非甲烷总烃样品保存时限探讨

非甲烷总烃在监测过程中,废气样品保存容器的选择和保存时间的长短对分析结果有重要影响。研究结果表明:使用玻璃注射器保存样品,应在8 h内完成分析;使用泰德拉惰性气袋保存样品,保存时间可延长至48 h,如废气中主要组分为沸点高于150℃的高沸点化合物,则应在8 h内完成非甲烷总烃的测定。     

关于改进非甲烷总烃测定方法的探讨

根据非甲烷总烃排放标准、分析方法和实际监测情况，对非甲烷总烃定义、总烃峰型异常、氧峰干扰、方法检出限测定和采样容器选择等方面存在的问题进行了探讨。结果表明：气态烃的衍生物属于非甲烷总烃，烃的衍生物和色谱柱类型是导致总烃峰型异常的主要原因，使用除烃空气作载气可消除氧峰干扰，非甲烷总烃为差值结果，应按照EPA SW-846标准测定检出限，PVF气袋本底低、气密性和化学惰性好，是最佳的非甲烷总烃采样容器。     

VOCs在线监测进样方式对非甲烷总烃测定的影响

采用正压、负压、大气平衡3种进样方式，研究了VOCs在线监测系统对非甲烷总烃测定的影响。探讨在大气平衡进样方式下定量环内压力、平衡时间、进样流量对非甲烷总烃测定的影响，研究结果表明：采用正压进样方式，定量环内正压增大，非甲烷总烃质量浓度偏高；采用负压进样方式，定量环内负压增大，非甲烷总烃质量浓度降低；采用大气平衡进样方式，定量环内压力、平衡时间、进样流量的增大或减小对非甲烷总烃测定没有明显影响。比较3种进样方式，大气平衡进样方式的VOCs在线监测系统能够提高非甲烷总烃在线监测结果的准确性和可靠性，更适用于污染源废气在线监测。     

南京市固定污染源非甲烷总烃在线监测系统比对监测探讨

对南京市某典型企业固定污染源非甲烷总烃在线监测系统开展比对监测,将在线监测结果和便携式仪器监测、手工监测结果作比对分析。结果表明,在线监测系统线性误差与量程漂移可以满足现阶段管理要求,实际样品比对过程中采用不同的采样分析仪器,监测结果差距较大,便携式分析仪结果相对误差较小(为3. 72%),手工监测结果相对误差较大(为48. 3%)。建议加强污染源废气手工监测的质控管理,强化在线监测设备的运维管理,推进污染源非甲烷总烃CEMS合理有序发展。     

气相色谱法检测废气中甲烷、非甲烷总烃的问题研究

气相色谱法检测废气中甲烷、非甲烷总烃的方法存在诸多问题。针对标准参考气体的选择、采样方式、样品保存、配气方式、仪器配置等方面做了重点研究。结果表明,使用甲烷作为标准参考气体最佳,根据污染源的实际状况,可选择动力采样或玻璃注射器手动采样。样品气保存在惰性气袋中比玻璃注射器更好,实验分析更推荐双柱配置的气相色谱,手工配制标准气系列、使用填充柱也可很好的满足检测的质量要求。     

全玻璃针筒注射器保存空气中甲烷和总烃的影响因素

采用全玻璃针筒取样/保存、双通道双毛细管柱测定非甲烷总烃分析方法,以甲烷标准气体样品、标准气体样品(TO-14、TO-15),以及3种实际环境空气样品为例,考察了全玻璃针筒注射器取样保存影响检测结果的若干因素。结果表明,样品的保存时间取决于以下因素:(1)样品性质,不同类型样品的保存时间差异大,化学反应活性强的样品,其总烃含量呈现先升高后降低趋势,甲烷则相对稳定;(2)样品浓度水平,相同条件下相同类型样品,浓度高的保存时间短于低浓度样品,如与环境空气浓度相仿的样品保存时间可超过60 h;(3)保存环境的避光程度,对于同一种VOCs标准气体样品,避光、半避光、非避光保存样品回收率迥异,趋势差别极大,对于部分样品即便是避光保存仍发现回收率变化极大;(4)全玻璃材质注射器的气密性,需对照技术规范要求,进行气密性的检查。     

罐采样-加压进样-气相色谱法测定环境空气中非甲烷总烃研究

建立了罐采样-气相色谱法测定环境空气中非甲烷总烃的分析方法。用罐采集环境空气样品至微负压状态，经除烃空气加压后，用气相色谱仪进行分析。并对氮气空白、除烃空气、样品保存期限、不同压力进样、不同正压压力进样、不同湿度、不同种类物质对总烃的贡献等进行了研究，在最佳实验条件下，非甲烷总烃的方法检出限为0.04μmol/mol,标准曲线相关系数均大于0.999 5,低、中、高浓度水平测定结果相对标准偏差均小于2.0%,低、中、高浓度的质控样品相对误差均小于2.0%。利用该方法对环境空气样品进行了检测分析，该法完全满足国家标准质控的要求，适用于环境空气和污染源无组织废气中非甲烷总烃的准确测定。     

直接进样-气相色谱质谱法同时测定固定污染源排气中的含氟温室气体

建立了一种直接进样-气相色谱质谱法同时分离和测定固定污染源排气中三氟甲烷、四氟甲烷、六氟乙烷和六氟化硫等含氟温室气体的方法。使用CP-Sillica PLOT毛细管填充柱可使上述4种目标化合物实现基线分离。分别用全扫描模式和选择离子扫描模式进行定量分析,方法检出限分别为0.12,0.19,0.10,0.08 mg/m~3和2.8,3.4,1.7,3.1μg/m~3。探讨了样品保存容器与保存时间对样品浓度衰减的影响,指出Tedlar采样袋或铝塑复合膜采样袋可以较长时间保存样品,在常温下,样品可保存至少7 d。实际样品测定结果表明方法快速、简便,适用于固定污染源排气中含氟温室气体的测定。     

固定污染源非甲烷总烃自动连续监测系统比对监测

对非甲烷总烃自动连续监测系统进行示值误差、响应时间、零点漂移和量程漂移等性能测试,对非甲烷总烃便携式分析仪进行检出限、精密度、准确度等性能测试。性能测试满足相关要求后同时利用便携式催化氧化-氢火焰离子化检测器法(催化氧化-FID)、便携式气相色谱-氢火焰离子化检测器法(GC-FID)和实验室气相色谱-氢火焰离子化检测器法(GC-FID)对固定污染源非甲烷总烃自动连续监测系统进行现场比对测试。测试结果表明,在工况变动较大的情况下,便携式FID法与实验室GC-FID法测试结果相对误差为19. 6%～35. 1%,具有很好的可比性。以实验室GC-FID法为参比方法时,自动连续监测系统相对准确度为64. 1%,不满足《固定污染源废气非甲烷总烃连续监测系统技术要求及检测方法》(HJ 1013—2018)的要求。以便携式FID为参比方法时,自动连续监测系统相对准确度分别为28. 6%和35. 3%,相对《固定污染源废气总烃、甲烷和非甲烷总烃的测定气相色谱法》(HJ 38—2017)方法一致性更好,均能满足《HJ 1013—2018》的要求。提出,应推进便携式方法在自动连续监测系统验收和质控比对中的应用。     

浅谈环境实验室采样容器的抽样检测方法

为了规范环境监测环节,严把质量关,确保监测数据和信息的准确可靠。实验室需严格控制采样容器等的清洗环节,并应对已清洗的采样容器进行抽样检测,从源头做好质量把控。本文针对有机物(总石油烃、酚类化合物、多环芳烃)、重金属及总氰化物等项目设计了检测方案,并取得了较好的结果。     

自动进样及气体分流技术测定气体中非甲烷总烃

采用自动进样和气体分流技术,双柱双FID检测器气相色谱法测定气体中的非甲烷总烃,实现了非甲烷总烃的连续自动分析,同时一次进样即可得到甲烷和总烃的数据。方法的检出限为0.05 mg/m3,测定的相对标准偏差在0.7%~1.8%内,非甲烷总烃的加标回收率为96.0%~98.5%。与传统手动进样法相比,本方法具有重复性好、操...     

ICP-AES法和分光光度法测定工业废水中总磷的方法比较

用ICP-AES法和分光光度法同时测定4种不同工业废水中的总磷含量,将2种方法的测定结果作比对。试验表明,ICP-AES法对国家标准样品的测定结果具有较高的准确度和精密度,4种废水样品测定结果的加标回收率为94.0%~110%,RSD在0.9%~3.2%之间。分光光度法适用于低浓度、低干扰样品的测定,对于高浓度含磷废水,取样体积和样品稀释倍数均会对其测定结果产生显著影响。消解样品经浊度-色度补偿后,分光光度法的测定结果精密度较低。     

Sources of volatile organic compounds in Cairo’s ambient air

The greater Cairo area suffers from extreme levels of gas and particulate phase air pollutants. In order to reduce the levels of ambient pollution, the USAID and the Egyptian Environmental Affairs Agency (EEAA) have supported the Cairo Air Improvement Project (CAIP). As part of this project, two intensive ambient monitoring studies were carried out during the period of February 22 to March 4 and October 27 to November 27, 1999. Volatile organic compounds (VOCs) were measured on a 24-h basis at six sampling stations during each of the intensive periods. During the February/March study, samples were collected daily, while in the October/November study samples were collected every other day. The six intensive measurement sites represented background levels, mobile source impacts, industrial impacts, and residential exposure. High levels of NMHC were observed at all locations. NMHC concentrations ranged from 365 ppb C at Helwan to 1,848 ppb C at El Qualaly during winter, 1999 and from 461 ppb C at Kaha to 2,037 ppb C at El Qualaly during fall, 1999. El Qualaly, the site chosen to represent mobile emissions, displayed the highest average NMHC concentrations of any site, by a factor of 2 or more. The highest mobile source contributions were estimated at this site. The major contributors to NMHC at all sites were mobile emissions, lead smelting, and compressed natural gas.     

Simultaneous monitoring of atmospheric methane and speciated non-methane hydrocarbon concentrations using Peltier effect sub-ambient pre-concentration and gas chromatography

Sub-ambient trapping, used to pre-concentrate atmospheric samples for non-methane hydrocarbon (NMHC) analysis by gas chromatography, can also be used to measure ambient methane concentrations. Above a sample volume of 40 ml, a dynamic equilibrium is established between ambient and trapped methane allowing for simultaneous quantitative determinations of methane and NMHC. The temperature stability of the trap is critical for quantitative methane analysis and this can be achieved by Peltier effect cooling. Simultaneous measurements of methane and NMHC reduce the equipment required for field trips and can ease the interpretation and modelling of atmospheric data. The feasibility for deployment of the system in remote locations was demonstrated by running the apparatus virtually unattended for a 5-day period. The correlations between the concentrations of methane, ethane and ethene measured during this period are discussed.     

SPME-based air sampling method for inhalation exposure assessment studies: case study on perchlorethylene exposure in dry cleaning

Exposure to perchlorethylene, especially for dry cleaning workers and for people living near dry cleaning shops, could lead to several diseases and disorders. This study examines the value of solid-phase microextraction (SPME) for sampling perchlorethylene in the atmosphere of dry cleaning shops. Carboxen/polydimethylsiloxane (CAR/PDMS) in 0.5-cm retracted mode was selected. There were no significant differences between sampling rates at different temperatures (range of 20 to 30 °C) and air velocities (2 to 50 cm/s). On the opposite, relative humidity (RH) had a significant effect on sampling rates. Method reproducibility was realized in the laboratory and field conditions and was 6.2 % and 7 to 11 %, respectively. Repeatability was also determined as 8.9 %. Comparison of the results according to the American Industrial Hygiene Association exposure assessment strategy showed the SPME sampler yields more conservative results in comparison with traditional standard method.     

离子色谱法测定环境空气中氯化氢时应注意的问题

用离子色谱法测定大气中低浓度氯化氢,方法灵敏、准确度高,但测定过程极易受污染干扰.本文主要探讨了在前期准备、采样和分析全过程中应注意的一些问题.