环境空气中多环芳烃的采样与分析技术

文章对环境空气中多环芳烃的采样与分析方法进行了概述,侧重介绍了样品的采集、净化、采样效率的评估方法和采样分析全过程的质量控制.     

废水矿物油采样与样品萃取

废水矿物油采样与样品萃取张向东，李峰（山东省滨州地区环境监测站２５６６１４）废水矿物油的采样及样品萃取的乳化现象是影响油类测定结果的重要因素，如果水样采集不当，样品萃取过程中乳化现象处理不好，会对测定结果产生较大影响。１样品采集水中油类物质主要来自采...     

化学吸收法采集固定污染源氨气的影响因素探究

固定污染源氨气的手工监测，干扰因素较多，其中采样环节尤为关键。实验通过催化氧化-化学发光法考察不同采样管线材质对氨气的吸附效果，离子色谱法考察化学吸收法采集氨气的吸收瓶类型、采样流量、吸收液种类、吸收液浓度及体积等采样条件对氨气吸收效率的影响。实验表明，316 L不锈钢与聚四氟乙烯对氨气的吸附较小，氨气的采样流量不宜超过1.0 L/min,棕色气泡式吸收瓶更适用于氨气样品的采集，磷酸溶液作吸收液对氨气的吸收效率较好，对于低浓度的氨气样品，应采用低流量长时间采集。     

一种新的采集地下水的抽水泵

美国华盛顿州里奇兰的巴特尔西北太平洋研究所生产的一种新型抽水泵用于地下水监测采样可大大降低采样的成本。这种新型的抽水泵用不锈钢和聚四氟乙烯材料制成,可以保证采样过程样品免遭污染。用这种泵采样只要20一40分钟就能采集一个有代表性的地下水样品。而目前使用的抽水泵要8个小时左右才能采集到一个样品。一种新的采集地下水的抽水泵@陶甄~~     

环境监测采样中的质量控制

环境样品采集过程的质量控制是监测工作的薄弱环节.本文研究了采样过程的质量控制,并用定量的方法将采样误差与实验分析误差区分开来.     

固体废物样品采集过程中几种采样误差的研究

固体废物由于其自身特殊的理化特性和在产生、排放以及存贮过程中存在着的随机和非随机不均匀性,使得欲采集有“代表性”的样品要比采集大气、水质样品困难得多,如果采样误差大,无论怎样降低采样误差,也很难对污染物有一个正确评价.由此可见,降低采样误差至关重要.1.采样方法带来的采样误差在污染源的固体废物采样过程中,要根据污染物的不同的产生排放形式和采样目的选择     

挥发性有机物污染土壤样品采样方法比较

以苯系物污染土壤样品的采集为例,比较了4种不同采样方法导致样品检测结果的差异。其中,方法 1将样品装填至广口瓶内并压实密封,方法2采用非扰动采样器采集10 g样品后转移至加有10 mL甲醇保护剂的Vial瓶中密封,方法 3用非扰动采样器采集10 g样品后直接将其密封于采样器内,方法 4用Encore采样器采样后将其密封于采样器内。结果表明,方法 2采集样品的检出率最高,其余3种方法的差异不明显,方法 2采集样品的检出结果 71%以上都大于其余3种方法。而且,对于挥发性较强的苯与甲苯,以方法 2采集的样品91%以上都大于其余3种方法,最大及平均检出浓度高出2~3个数量级。5种不同土质样品检测结果表明,对于有机质含量较低的细砂,方法2的最高及平均检出浓度均高于其余3种方法 1~3个数量级,差异随土壤有机质含量的升高而降低。可见,对于苯系物及挥发性强于苯系物的其他挥发性有机物污染土壤样品的采集,方法 2效果最优,可指定为VOCs污染场地土壤样品的采样方法。     

环境空气中气态和颗粒态总氟化物分析方法优化

对双层磷酸氢二钾浸渍滤膜采集-氟离子选择电极测定环境空气中1、24 h气态和颗粒态总氟化物的方法进行了优化研究。方法采用小流量采集(24 h采样流量为16.7 L/min,1 h采样流量为50 L/min),解决了现有方法在样品采集上的问题,优化了样品制备中超声提取和静置方法。采样体积为3、24 m~3时,方法检出限分别为0.5、0.06μg/m~3,测定下限分别为2.0、0.24μg/m~3。实际样品测定,采样1 h时,加标回收率为87.9%~109%;采样24 h时,加标回收率为80.2%~99.3%,平行样测定的精密度为0.3%~2.9%,方法精密度和准确度良好,适用于环境空气中氟化物的测定。     

大气颗粒物元素组分及分布的研究

1.布点与采样我们在沈阳市城区内设居民区、文化区、交通区和工业区四个采样点,在郊区设一个对照点,共设五个采样点.采样用美国安德逊五段撞击式大流量器,分别采集了冬夏两季颗粒物样品.颗粒物的空气动力学直径范围见表1.     

自然环境中微塑料样品的采集与分离方法

综述了自然环境中微塑料样品采集与分离方法的研究进展,介绍了水环境、土壤与沉积物、环境空气、生物体等不同介质中微塑料的采集方法、技术原理和使用条件,以及密度分离、筛选分离、滤膜过滤等分离提取和预处理方法,提出了建立统一的微塑料采样指南,开展空气中微塑料富集、采样、分离和检测标准方法研究等建议。     

燃煤电厂烟气中汞的采集与分析方法

汞的测试技术包括采样和分析两部分,其中汞含量的分析方法已经相对比较成熟,限制测试技术发展的诸多问题主要来源于取样过程。根据不同的取样方式,将现有测试技术分为湿式采样分析法、干式采样分析法以及在线分析技术3种,重点介绍了3种方法的采样原理、系统构成、过程的影响因素以及适用范围。最后针对CVAAS、CVAFS、AES 3种汞含量测定技术在Hg CEMS测试系统中的应用进行了对比介绍。     

Statistical Analysis of Spatial Pattern: A Comparison of Grid and Hierarchical Sampling Approaches

Previous studies have combined random-site hierarchical sampling designs with analysis of variance techniques, and grid sampling with spatial autocorrelation analysis. We illustrate that analysis techniques and sampling designs are interchangeable using densities of an infaunal bivalve from a study in Poverty Bay, New Zealand. Hierarchical designs allow the estimation of variances associated with each level, but high-level factors are imprecisely estimated, and they are inefficient for describing spatial pattern. Grid designs are efficient for describing spatial pattern, and are amenable to conventional analysis. Our example deals with a continuous spatial habitat, but our conclusions also apply in disjunct or patchy habitats. The influence of errors in positioning is also assessed. The advantages of systematic sampling are reviewed, and more efficient hierarchical approaches are identified. The distinction between biological and statisticalsignificance in all analyses is emphasised.     

全流稀释风道机动车排放颗粒物采集系统的集成及其流量控制和调节

以机动车排放颗粒物采集和分析为主要目的,开发了全流稀释风道机动车排放颗粒物采集系统.文章阐述了全流稀释风道的系统集成以及流量控制系统的设计和调节,其中包括设计应用范围、主要技术参数、系统检定等.流量控制系统采用的关键技术,即文丘里管组合装配方式具有控制流量范围广、变更灵活的特点,可以适应小到摩托车,大到重型柴油车等不同类型车辆检测的需要.     

Workplace monitoring of hydrogen peroxide using titanyl-coated sorbents

The current methods of sampling hydrogen peroxide, based on bubbling in acid solutions (titanium tetrachloride or titanium oxysulfate), are unsuitable for personal sampling. An alternative medium has been developed: silica gel coated with titanium oxysulfate. Sample tubes of this new sampling medium are suitable for personal sampling. The sampling performance is the same as that of the methods based on bubbling, but the tubes must be desorbed as soon as possible, even if the spectrophotometric analysis can be postponed. Special emphasis has been placed on the possible interference by peracetic acid, which is currently used in conjunction with hydrogen peroxide in the food industry.     

煤气化过程中气态污染物采样分析的研究进展

通过考察气态污染物采样方法的基本原理，对比分析国内外常压采样系统和加压采样系统的设计特征，选择煤气化过程中5种常见气态污染物为分析对象，列举常用的化学分析法和仪器分析法，为加压气化装置采样系统的设计提供参考材料和建议，归纳了一些有助于提高气态污染物检测数据可靠性的措施，希望能为煤气化过程中（特别是加压煤气化过程中）气态污染物采样系统的设计提供思路和借鉴。     

A field-based spectrophotometric flow-injection system for automatic determination of chloride in soil water

The use of chloride as a tracer for soil water investigations is discussed. Limitations with laboratory based soil core and field based sampling are considered with respect to the poor suitability of the data for rigorous assessment of mechanistic models. Investigation of water movement in soil has been restricted by limitations in spatial and temporal sampling. Fine resolution sampling generates large numbers of samples which cause problems with post sampling laboratory analysis. This paper describes a field-based system for the analysis of chloride in soil water. There are three component parts to the system, (i) a custom sampling sub-system comprising of ceramic cup suction samplers and sample traps, (ii) a sample routing sub-system to channel sample to (iii) a sample analysis sub-system utilizing a flow injection method for sample analysis using a custom built photo-diode detector. The three sub-systems were controlled by a suitably equipped personal computer. A calibration procedure is described with a third order polynomial equation derived to convert millivolt response from the detector into chloride concentration. Field and laboratory data from a tracer experiment are presented and discussed, and it is concluded that the system is well suited to field-based applications. Finally it is noted that the photo-detector is suitable for colourimetric analysis of any tracer with suitable chemical determination.     

Evaluating the effectiveness of routine water quality monitoring in Miyun reservoir based on geostatistical analysis

This study used geographic information system techniques and geostatistics methods to evaluate the effectiveness of routine water quality monitoring in the western segment of the Miyun reservoir in Beijing. Methodologies as well as the sampling design are evaluated. The single-layer evaluation and three integrated evaluation methods including principal component analysis (PCA), ordinary kriging (OK)_Mean, and Mean_Layers were used to validate the effectiveness of evaluation methods, and the effectiveness of each sampling design was validated by comparing their errors. Results indicated that, while a single-layer evaluation only shows the trophic state of water at a specific level, an integrated evaluation synthetically analyzes and evaluates the trophic state of the entire water body. Furthermore, results of the integrated analysis show that a PCA method is more accurate and can represent the trophic state of the entire water body. The OK_Mean and Mean_Layers methods are only able to represent the mean level for trophic state of the entire water body but cannot reflect local trophic state and distribution details. Although methods used in the routine monitoring of Miyun reservoir have some similarities to the OK_Mean and Mean_Layers methods, their range of errors and uncertainty are greater because of a lack of detailed spatial continuous information. The analysis on the number of sampling points shows that, within a certain range of error, minor changes of sampling points will have no obvious impact on the monitoring results. For the routine monitoring of western Miyun reservoir, using only three to five sampling points for monitoring is inadequate. According to our analysis, it is more appropriate to use at least ten sampling points for monitoring these areas.     

地表水水样自然沉降放置试验与讨论

本文用四种方式对地表水样品的自然沉降在采样环节还是在分析环节进行实验,对BOD5、CODMn、CODcr之类分析时不需对样品进行预处理的项目有一定影响,自然沉降在分析环节的监测结果低于在采样环节的监测结果;对氨氮、总磷之类分析时需对样品进行预处理的项目影响几率基本持平。     

Volatile Organic Compounds: Sampling Methods and Their Worldwide Profile in Ambient Air

The atmosphere is a particularly difficult analytical system because of the very low levels of substances to be analysed, sharp variations in pollutant levels with time and location, differences in wind, temperature and humidity. This makes the selection of an efficient sampling technique for air analysis a key step to reliable results. Generally, methods for volatile organic compounds sampling include collection of the whole air or preconcentration of samples on adsorbents. All the methods vary from each other according to the sampling technique, type of sorbent, method of extraction and identification technique. In this review paper we discuss various important aspects for sampling of volatile organic compounds by the widely used and advanced sampling methods. Characteristics of various adsorbents used for VOCs sampling are also described. Furthermore, this paper makes an effort to comprehensively review the concentration levels of volatile organic compounds along with the methodology used for analysis, in major cities of the world.