毛细管气相色谱法测定烟草中有机氯农药残留

研究了烟草中六六六及滴滴涕异构体含量的气相色谱分析方法.样品以石油醚 丙酮在索氏提取器中提取,提取液以浓硫酸净化.采用DB-5弹性石英毛细管柱分离样品,GC-ECD检测农药六六六、滴滴涕的残留量.方法的线性范围为2.27×10-13～7.66×10-11g;最小检测量为1.3×10-8～3.0×10-7 μg,加标平均回收率为95.3%～103.3%,RSD为2.8%～4.5%.     

土壤中有机氯农药残留分析前处理方法研究

利用硅胶柱、氟罗里土柱净化前处理方法对浙江某地区土壤样品中六六六、滴滴涕有机氯农药的残留量进行分析,并与现行的GB/T 14550-1993浓硫酸净化前处理方法进行比较。实验结果表明,采用柱净化前处理方法加标回收率在78%～121%,两种前处理方法所得气相色谱分析结果的平均相对标准偏差小于±20%,表明利用柱净化前处理方法能满足痕量有机物残留分析的要求。     

超声波提取-气相色谱法测定土壤中残留六六六和滴滴涕

采用气相色谱法毛细管色谱柱分离、电子捕获检测器检测土壤中残留的六六六和滴滴涕含量。取风干过筛的土壤样品，用丙酮、石油醚（1：）浸泡，超声波提取，浸泡液经浓硫酸净化后进样测定。当土壤样品取样量为10g时，方法检测限α-六六六，γ-六六六为0.001mg/kg,β-六六六、δ-六六六、op'-DDT和pp'-DDT为0.004mg/kg,pp'-DDE,pp'-DDD为0.002mg/kg。加标回收率在77%-100%之间，相对标准偏差为2.5%-8.5%。方法简便、灵敏。     

微波萃取-气相色谱/质谱法测定土壤中的有机氯农药

通过微波萃取提取土壤中的有机氯农药,萃取溶液经浓硫酸脱色、佛罗里硅土柱净化,最后用气相色谱/质谱法分析.以石英砂为基体进行加标回收测定,有机氯农药的回收率在75.5%～103%之间,检出限为0.01μg/kg.     

土壤和沉积物中多氯联苯单体测定的净化方法研究

对浓硫酸净化、铜粉脱硫、氟罗里硅土柱、硅胶柱、石墨碳柱等净化方法在土壤和沉积物多氮联苯单体测定中的应用进行了研究.浓硫酸对多氯联苯单体的净化回收率达92.4％～109％;氟罗里硅土柱用正己烷/丙酮混合溶液淋洗,净化洗脱液体积为8 mL～10 mL时,回收率达85.7％ ～ 108％;硅胶柱用正己烷淋洗,净化洗脱液体积为...     

土壤介质中酞酸酯类污染物分析方法研究

介绍了加压流体提取(PFL、ASE)提取-GPC净化-GC/MS分析土壤中酞酸酯类污染物方法的程序和质控要求,研究了每个步骤对分析六种目标物准确度和精密度的影响以及测定实际土壤样品的情况.结果显示,加压流体提取(PFL)、浓缩和GPC净化各步骤全程序空白加标回收率分别在86.3%～108%、78.5%～117%和87.4%～103%范围,精密度均在15%以内.在实际土壤样品中加入六种酞酸酯标准的加标回收率在45.2%～103.4%范围内,其相对标准偏差8%～23%.     

固相萃取气相色谱法测定水中痕量六六六和滴滴涕

建立了固相萃取气相色谱测定水质中六六六、滴滴涕的方法,详尽地叙述了水样预处理过程。方法检测限较低,α六六六和γ六六六为1ng/L,β六六六、δ六六六和pp′DDE为2ng/L,op′DDT和pp′DDT为3ng/L,pp′DDD为4ng/L。加标回收率在88%～93%之间,回收较好,相对标准差均<2.5%,精密度好。方法快速、简便,避免了液液萃取的繁多手续。     

加速溶剂萃取-固相萃取小柱净化-气相色谱法测定土壤中有机磷农药

建立了加速溶剂萃取-固相萃取小柱净化-气相色谱法测定土壤中12种有机磷农药的方法。推荐了12种有机磷农药快速分离的色谱条件。采用加速溶剂萃取技术实现了对土壤中有机磷农药残留的提取,选取最佳条件参数,减少了组分的损失,提取回收率达88%～108%。选择不同填料的SPE小柱和洗脱溶剂形成3种方案法进行净化实验,结果表明,方案2采用混合溶剂(正己烷、丙酮、二氯甲烷体积比为1∶1∶1)洗脱上样后的硅胶SPE小柱的净化效果好,回收率为91%～121%。方法检出限为0.000 1～0.000 2 mg/kg,石英砂基体和实际污染土壤样品加标回收率为62%～112%,相对标准偏差为0.7%～8.6%。该方法操作简便,快捷,灵敏度高,检出限低,试剂用量少,准确度和精密度符合质量控制要求。     

超声波萃取-气相色谱/质谱法测定土壤中15种Pops类有机氯农药

用探头式超声波萃取仪、己烷/丙酮混合溶剂提取土壤中的15种Pops类有机氯农药(包括六氯苯、七氯、六六六、氯丹、艾氏剂、狄氏剂、异狄氏剂、灭蚁灵、滴滴涕),萃取溶液经氟罗里硅土柱净化、氮吹浓缩,用气相色谱/质谱仪(GC-MS)进行测定。方法检出限0.4～1.4μg/kg,空白样品有机氯农药加标回收率为52.8%～118%、有机氯标记替代物回收率为71.0%～122%,RSD为6.8%～16.5%。     

气相色谱法检测地下水中六六六和滴滴涕

采用环己烷萃取、浓硫酸净化,联合气相色谱电子捕获检测器分析地下水中的六六六和滴滴涕,优化了升温程序、进样口温度、衬管等分析参数。8种组分在8.6 m in内完全分离,在0.001 mg/L~0.200 mg/L范围内标准工作曲线线性良好,检出限为0.03μg/L~0.38μg/L,标准溶液平行测定的RSD为0.1%~4.8%,加标回收率为90.0%~131%。     

气相色谱-串联质谱法测定土壤中十氯酮

研究了提取溶剂效率、净化方式等因素对十氯酮测定的影响,对比了加速溶剂提取、微波萃取及超声波等提取方式,考察了不同电子轰击能量、碰撞能量下特征离子对的响应。建立了加速溶剂萃取,H2SO4净化分离,气相色谱法-三重四极杆质谱法测定土壤中十氯酮的分析方法。取5.0 g土壤干样,内标法定量,线性相关系数为0.999 7,加标回收率为91.7%~121%,相对标准偏差为3.4%(n=6),检出限为0.1 ng/kg。     

Conventional, microwave, and ultrasound sequential extractions for the fractionation of metals in sediments within the Petrochemical Industry, Serbia

In this paper, the main objective was fractionation of Cd, Cu, Ni, Pb, Zn, Ca, Fe, and K in certificate material and sediment samples gathered from and around the Petrochemical Industry using the conventional, microwave and ultrasonic sequential extraction. Microwave oven and ultrasound bath were used as an energy source for achieving faster extraction. Additional heating and boiling of samples were avoided by using lower power and shorter time for microwave and ultrasound extraction. Precision and accuracy of procedure were evaluated by using certificate material (BCR701). Acceptable accuracy of metals (87.0–111.3 %) was achieved for all three-step sequential of conventional extraction protocol. An accuracy of the fourth step has been verified with two certificate materials: BCR143R and 146R. The range of total extracted metal concentrations from sediments was similar for all three extraction techniques. A significant high percentage of Cd, Cu, and Zn were obtained after extraction of the exchangeable and acid soluble sediment fraction. Principal component analysis of values obtained after determination of risk assessment code using conventional and ultrasound sequential extraction show similarity of these values. Accuracy, recovery, and risk assessment code values imply that ultrasound sequential extraction is a more suitable, accelerated sequential extraction procedure (30 min per extraction step) than microwave extraction in applied conditions.     

微波萃取技术在分析土壤中有机污染物的应用

介绍了微波萃取技术及其使用的试剂、设备和条件,对微波萃取在分析土壤中有机污染物的应用予以综述,阐述了微波萃取技术是分析土壤中有机污染物的好方法。     

Environmental survey in the Tuul and Orkhon River basins of north-central Mongolia, 2010: metals and other elements in streambed sediment and floodplain soil

Streambed sediment and subsurface floodplain soil were sampled for elemental analyses from 15 locations in river basins of north-central Mongolia during August 2010. Our primary objective was to conduct a reconnaissance-level assessment of potential inputs of toxicologically important metals and metalloids to Lake Baikal, Russia, that might originate from mining and urban activities within tributaries of the Selenga River in Mongolia. Samples were collected in triplicate from all sites, then dried, and sieved to <2 mm for analysis by portable X-ray florescence spectroscopy and by inductively coupled plasma mass spectrometry after digestion with concentrated nitric and hydrochloric acids. Arsenic, copper, and mercury were greatly elevated in sediment and floodplain soil collected from tributary streams located near two major mining operations. Lead and zinc were moderately elevated in streambed sediment and in floodplain soil obtained from a small tributary in the capital city of Ulaanbaatar, but those concentrations were considerably less than probable effects benchmarks. Historical and possibly present mining activities have led to considerable metal contamination in certain tributaries of the Orkhon River in north-central Mongolia; however, metals originating from those sources did not appear to be accumulating in sediments at our downstream-most sampling sites located near the border between Mongolia and Russia.     

Determination of arsenic species in fish, crustacean and sediment samples from Thailand using high performance liquid chromatography (HPLC) coupled with inductively coupled plasma mass spectrometry (ICP-MS)

Suitable techniques have been developed for the extraction of arsenic species in a variety of biological and environmental samples from the Pak Pa-Nang Estuary and catchment, located in Southern Thailand, and for their determination using HPLC directly coupled with ICP-MS. The estuary catchment comprises a tin mining area and inhabitants of the region can suffer from various stages of arsenic poisoning. The important arsenic species, AsB, DMA, MMA, and inorganic arsenic (As III and V) have been determined in fish and crustacean samples to provide toxicological information on those fauna which contribute to the local diet. A Hamilton PRP-X100 anion-exchange HPLC system employing a step elution has been used successfully to achieve separation of the arsenic species. A nitric acid microwave digestion procedure, followed by carrier gas nitrogen addition- (N2)-ICP-MS analysis was used to measure total arsenic in sample digests and extracts. The arsenic speciation of the biological samples was preserved using a Trypsin enzymatic extraction procedure. Extraction efficiencies were high, with values of 82-102%(As) for fish and crustacean samples. Validation for these procedures was carried out using certified reference materials. Fish and crustacean samples from the Pak Pa-Nang Estuary showed a range for total arsenic concentration, up to 17 microg g(-1) dry mass. The major species of arsenic in all fauna samples taken was AsB, together with smaller quantities of DMA and, more importantly, inorganic As. For sediment samples, arsenic species were determined following phosphoric acid (1 M H3PO4) extraction in an open focused microwave system. A phosphate-based eluant, pH 6-7.5, with anion exchange HPLC coupled with ICP-MS was used for separation and detection of AsIII, AsV, MMA and DMA. The optimum conditions, identified using an estuarine sediment reference material (LGC), were achieved using 45 W power and a 20 minute heating period for extraction of 0.5 g sediment. The stability and recovery of arsenic species under the extraction conditions were also determined by a spiking procedure which included the estuarine sediment reference material. The results show good stability for all species after extraction with a variability of less than 10%. Total concentrations of arsenic in the sediments from the Pak Pa-Nang river catchment and the estuary covered the ranges 7-269 microg g(-1)and 4-20 [micro sign]g g(-1)(dry weight), respectively. AsV was the major species found in all the sediment samples with smaller quantities of AsIII. The presence of the more toxic inorganic forms of arsenic in both sediments and biota samples has implications for human health, particularly as they are readily 'available'.     

Transportation and fate of cationic surfactant in river water

The degradation, sorption, transportation and material balance of cationic surfactants discharged from domestic waste into river water was studied. Ion-pair solid-phase extraction behavior showed that the sorption of cationic surfactants as an ion-pair with anionic surfactant onto river sediment was so strong that little cationic surfactant was found in the bulk water. Cationic surfactant was found in river sediment at more than 500 times higher concentration than that in the bulk water. The degradation of the cationic surfactant was very slow in river water and much slower in the sediment. A material balance of cationic surfactant was estimated for a river running through Toyama City by measuring the flow rate and the concentration of cationic surfactant in the water at several points. It was found that more than 30% of cationic surfactant introduced to the river was lost during the river running through ca. 3 km in 3 h. This reduction probably comes from a quick transfer of the cationic surfactant from river water to sediment and water weed by means of adsorption or precipitation with suspending solids.     

公园地表土中多环芳烃的分离提取及含量分析

比较加压液体萃取法、超声波辅助萃取技术和微波辅助提取技术对公园地表土中多环芳烃的提取效率,并对目标化学成分进行分析鉴定。以超高效液相色谱-三重四极杆质谱作为分析方法,共分离检测出16种多环芳烃类化合物,分别为萘、苊、苊烯、氟、菲、蒽、荧蒽、芘、苯并[a]蒽、艹屈、苯并[b]荧蒽、苯并[k]荧蒽、苯并[a]芘、二苯并[a,h]蒽、茚并[1,2,3-cd]芘和苯并[ghi]苝。结果表明:加压液体萃取法、超声波辅助萃取技术和微波辅助提取技术均可以有效提取公园地表土中多环芳烃类成分。超高效液相色谱-质谱联用技术可以有效地分析公园地表土中多环芳烃类成分。     

Effect of ultrasonic agitation on the release of copper, iron, manganese and zinc from soil and sediment using the BCR three-stage sequential extraction

An ultrasonic bath and an ultrasonic probe have been used to develop rapid versions of the three-stage Community Bureau of Reference (BCR, now the Standards, Measurement and Testing Programme) sequential extraction procedure. The effect of the ultrasonic treatments on the extraction of copper, iron, manganese and zinc from a sewage sludge-amended soil has been assessed. Recoveries similar to those of conventional shaking (i.e., conventional value, +/- 30%) could generally be obtained for copper, manganese and zinc, but not for the important matrix element iron. With the use of compromise sonication conditions, steps 1, 2 and 3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 3, 5 and 1 min, respectively, using the ultrasonic probe, and in 3, 1 and 1 h, respectively, using the bath. The extraction procedures developed using the soil performed well when applied to lake sediment BCR CRM 601. Analyte partitioning was generally similar to that obtained with mechanical shaking, and overall metal recoveries were 84-98% of those obtained with the conventional BCR protocol, except for copper extracted with the probe (74%). Poorer performance (analyte recoveries, 58-104%) was obtained when the methods were applied to an intertidal sediment. This highlights the difficulty of developing a version of the BCR extraction, with ultrasonic assistance, which gives a performance equivalent to conventional shaking when applied to different substrates.     

Effectiveness of amendments on re-acidification and heavy metal immobilization in an extremely acidic mine soil

Previous studies have shown that the application of soil amendments is efficient in reducing acidity and heavy metal bioavailability in mine soils. However, it remains a challenge for environmentalists to predict accurately and control economically the re-acidification in re-vegetated mine soils. In this study, net acid generation (NAG) test and bioassay technique were employed to assess the effectiveness of the amendments [including lime, N-P-K (nitrogen, phosphorous and potassium) fertilizer, phosphate and river sediment] on re-acidification and heavy metal immobilization in an extremely acid (pH < 3) mine soil. Our results suggested that NAG test was a rapid and accurate approach to assess the effectiveness of the amendments on re-acidification potential of the mine soil. Interestingly, it was found that phosphate and river sediment played quite specific roles in preventing the re-acidification in the mine soil. In addition, the results also indicated that the addition of 25 t ha(-1) lime combined with river sediment (30%) might be an economical method to successfully control the acidification and re-acidification in the extremely acid mine soil, allowing the re-establishment of the plants. Collectively, our results implied that the combined use of NAG test and bioassay assessment was effective in evaluating a reclamation strategy for extremely acidic mine soils.