Validation of Urban Emission Inventories

Two emission validation methods are presented. The first method focuses on the precision of the emission factors and the accuracy of modelled traffic flows. Emission factors derived from the COPERT II methodology are compared with on-board emission measurements and modelled traffic flow rates are compared with observations. The second validation method focuses on the completeness of the inventory, i.e. coverage of all sources. The method compares measured pollutant fluxes in the urban plume with the downwind transported and dispersed emissions integrated over plume width and mixing height. Both methods seem to indicate that traffic emission factors used in the urban emission inventories show large uncertainties. Besides the lack of measurement precision this is mainly induced by external influence factors like driving behaviour and vehicle maintenance.     

汽车修理养护企业挥发性有机物排放控制标准探讨

通过对汽车修理养护企业喷烤漆废气排放现状进行调查分析,指出中国目前适用于控制汽车修理养护企业废气排放的标准《大气污染物综合排放标准》(GB 16297-1996)在实际运用中存在的问题。依据《制定地方大气污染物排放标准的技术方法》(GB/T 3840-1991)《大气污染物综合排放标准详解》《工作场所有害因素职业接触限值化学有害因素》(GBZ 2.1-2007)《工业企业设计卫生标准》(TJ 36-1979)、美国环保局多介质环境模型等,用不同方法计算汽车修理养护企业排放的废气中几种挥发性有机物的排放浓度和排放速率限值,并对监测结果进行评价分析,提出编制汽车修理养护企业废气排放控制标准的建议。     

An Evaluation of Microscopic Emission Models for Traffic Pollution Simulation Using On-board Measurement

As a result of the continuously increasing numbers of motor vehicles in metropolitan areas worldwide, road traffic emission levels have been recognized as a challenge during the planning and management of transportation. Experiments were conducted to collect on-road emission data using portable emission measurement systems in two Chinese cities in order to estimate real traffic emissions and energy consumption levels and to build computational models for operational transport environment projects. In total, dynamic pollutant emissions and fuel consumption levels from dozens of light duty vehicles, primarily from four different vehicle classes, were measured at a second-by-second level. Using the collected data, several microscopic emission models including CMEM, VT-Micro, EMIT, and POLY were evaluated and compared through calibration and validation procedures. Non-linear optimization methods are applied for the calibration of the CMEM and EMIT models. Numerical results show that the models can realize performance levels close to the CMEM model in most cases. The VT-Micro model shows advantages in its unanimous performance and ability to describe low emission profiles while the EMIT model has a clear physics basis and a simple model structure. Both of them can be applied when extensive emission computation is required in estimating environmental impacts resulting from dynamic road traffic.     

Mean Vehicle Speed Distributions for the Spatiotemporal Estimation of Exhaust Emissions

Link Emissions Models estimate traffic-related air pollution emissions at the individual road link level and inform governmental policies for air quality management. The current South Australian Link Emissions Model (CLEM) assumes constant spatiotemporal traffic flow at a single fixed mean speed, a potential limitation as the variability of exhaust emissions with vehicle speed has been established in the literature.We extend CLEM to eliminate the assumption of constant traffic flow, through the derivation of mean Australian vehicle speed distributions for different road types. Specifically, we successfully model the vehicle speed profile data from the second National In-Service Emissions study using Nearest Neighbour Kernel Density Estimation. We propose a mean speed Distribution Link Emissions Model (DLEM) for exhaust emission estimation based on the derived mean speed distributions. DLEM is an augmented, enhanced version of CLEM, accommodating a range of vehicle speeds and road types. The performance of the extended model, DLEM, is analysed in comparison to the current model, CLEM, through a case study analysis of vehicle exhaust emissions on a typical arterial road in Adelaide, South Australia. Results indicate use of DLEM and, by extension, mean vehicle speed distributions, has a strong impact on emission estimation. In particular, the fixed speed model, CLEM, may be substantially underestimating exhaust emissions of carbon monoxide, non-methane volatile organic compounds and particulate matter less than 2.5 μm in diameter. These are common exhaust pollutants that have been extensively linked with adverse health effects including respiratory morbidity and premature mortality.     

不同类型机动车尾气挥发性有机化合物排放特征研究

机动车尾气主要成分包括一氧化碳、氮氧化物、碳氢化合物、铅及苯并[a]芘等.其中,挥发性有机化合物由于其对光化学烟雾的贡献及对人体健康的影响而成为近年来大气化学研究的热点.文章首次对北京市9种车辆、5种燃料在不同工况下排放挥发性有机化合物特征进行了定量研究.结果表明,车型、燃料、净化器及工况等因素对排放量产生影响,电喷车比化油器车排放低,其中,夏利比富康与奥迪排放量高;LPG与汽油车排放量最高,柴油车与CNG车排放最低.其中,-10#柴油车比0#柴油车排放更低;使用净化器可以降低挥发性有机化合物排放量;不同工况对排放量的影响随车型、燃料类型的不同而不同.因此,使用清洁燃料、安装净化器和使用电喷装置,可减少尾气中挥发性有机化合物含量.     

梅梁湖的富营养化状况及治理对策讨论

监测结果表明，梅梁湖水体ＴＰ，ＴＮ含量分别为０．１ｍｇ／Ｌ和３．４ｍｇ／Ｌ藻类生物量达９－１３亿个细胞／Ｌ，富营养化相当严重，污染的主要原因，工农业，渔业，畜牧业和生活污水的直接排放，使水全营养盐含量较高，藻类大量繁殖，可采用“控源截汛”，“清除淤泥”，“调水搞活”及生物治理等综合性措施，对梅梁湖的富营养化进行了治理。     

Assessment of Mexico��s program to use ethanol as transportation fuel: impact of 6% ethanol-blended fuel on emissions of light-duty gasoline vehicles

Recently, the Mexican government launched a national program encouraging the blending of renewable fuels in engine fuel. To aid the assessment of the environmental consequences of this move, the effect of gasoline fuel additives, ethanol and methyl tert-butyl ether, on the tailpipe and the evaporative emissions of Mexico sold cars was investigated. Regulated exhaust and evaporative emissions, such as carbon monoxide, non-methane hydrocarbons, and nitrogen oxides, and 15 unregulated emissions were measured under various conditions on a set of 2005?C2008 model light-duty vehicles selected based on sales statistics for the Mexico City metropolitan area provided by car manufacturers. The selected car brands are also frequent in Canada, the USA, and other parts of the world. This paper provides details and results of the experiment that are essential for evaluation of changes in the emission inventory, originating in the low-blend ethanol addition in light vehicle fuel.     

上海市机动车污染实时排放预警系统设计与应用

研究上海市机动车污染的动态排放测算和网格化动态排放清单构建,在实时的交通数据和交通环境监测数据的基础上,结合交通模型、机动车排放清单模型等业务模型和算法,依托大数据存储、可视化和GIS等技术,开发了上海市机动车污染物实时排放预警系统,实现了上海市全市道路的机动车动态排放测算、交通环境政策实施情景模拟和网格化排放清单,更新频率为每30 min一次,包含PM、NOx、CO、SO2、VOCs等污染物和9种车型。系统建成后直接服务于首届中国国际进口博览会,为大气污染排放实时总量跟踪评估、污染源管控措施分析及监测成因分析等提供了有力的实时数据和技术支撑。     

New research assessing the effect of engine operating conditions on regulated emissions of a 4-stroke motorcycle by test bench measurements

In the latest years the effect of powered two-wheelers on air polluting emissions is generally noteworthy all over the world, notwithstanding advances in internal combustion engines allowed to reduce considerably both fuel consumption and exhaust emissions of SI engines. Nowadays, in fact, these vehicles represent common means of quotidian moving, serving to meet daily urban transport necessities with a significant environmental impact on air quality. Besides, the emissive behavior of the two-wheelers measured under fixed legislative driving standards (and not on the local driving conditions) might not be sufficiently representative of real world motorcycle riding.The purpose of this investigation is a deeper research on emissive levels of in-use motorcycles equipped with last generation SI engines under real world driving behavior. In order to analyze the effect of vehicle instantaneous speed and acceleration on emissive behavior, instantaneous emissions of CO, HC and NO_X were measured in the exhaust of a four-stroke motorcycle, equipped with a three-way catalyst and belonging to the Euro-3 legislative category. Experimental tests were executed on a chassis dynamometer bench in the laboratories of the National Research Council (Italy), during the Type Approval test cycle, at constant speed and under real-world driving cycles. This analytical-experimental investigation was executed with a methodology that improves vehicles emission assessment in comparison with the modeling approaches that are based on fixed legislative driving standards. The statistical processing results so obtained are very useful also in order to improve the database of emission models commonly used for estimating emissions from road transport sector, then they can be used to evaluate the environmental impact of last generation medium-size motorcycles under real driving behaviors.     

System Dynamics Modeling and Policy Simulation for Urban Traffic: a Case Study in Beijing

This paper constructs a system dynamics model for simulating the impact of different strategies on urban traffic’s energy consumption and carbon emissions. Based on a case study in Beijing, the model includes three subsystems: (1) urban traffic, (2) population and economy, and (3) energy consumption and carbon emissions. First, the model is used to decompose the impact of different vehicles on energy consumption and carbon emissions. Decomposition results show that private cars have the most significant impact on urban traffic’s energy consumption and carbon emissions; however, total vehicle kilometers traveled by private cars are the smallest among four trip modes. Then, the model is used to simulate different urban traffic policies. Policies are categorized as follows: (a) driving restrictions on vehicle registration numbers, (b) a scheme for vehicle registrations via a lottery system, and (c) development of public transportation infrastructures. Scenario simulation results show that all those measures can reduce energy consumption and carbon emissions. Though the last strategy (c) contains several delays, its effect is more stable and far-reaching. Finally, some recommendations about easing traffic pressure and reducing traffic emissions are given.     

北京市高架道、桥交通噪声状况调查与对策研究

对北京市区内８１座道路立交桥和１１段高架道路的声环境状况进行了多方位的调研与实测。分析了高架道、桥附近声环境的地面水平分布特征、高层楼房垂直分布特征、昼夜时间分布特征及产生的原因。从增强城市总体规划与交通管理,注意沿街建筑功能配置与布局,加强临街住户门窗隔声效果,适当建设有效的道路隔声屏障等方面提出了城市发展中解决和控制交通噪声污染的对策建议。     

An Integrated Approach to Street Canyon Pollution Modelling

An integrated method for the prediction of the spatial pollution distribution within a street canyon directly from a microscopic traffic simulation model is outlined. The traffic simulation package Paramics is used to model the flow of vehicles in realistic traffic conditions on a real road network. This produces details of the amount of pollutant produced by each vehicle at any given time. The authors calculate the dispersion of the pollutant using a particle tracking diffusion method which is superimposed on a known velocity and turbulence field. This paper shows how these individual components may be integrated to provide a practical street canyon pollution model. The resulting street canyon pollution model provides isoconcentrations of pollutant within the road topography.     

New Metal Emission Patterns in Road Traffic Environments

The increased awareness of traffic as a major diffuse metal emission source emphasizes the need for more detailed information on the various traffic-related sources and how and where the metals are dispersed. In this study, metal emission patterns in the road traffic environment were examined from the perspective of different surrounding factors, e.g. the importance of intersections, deceleration, vehicle speed and traffic density. A total of 148 topsoil samples from 18 south Swedish roads were analysed (using GFAAS) for traffic-emitted metals, i.e. Cd, Cr, Cu, Ni, Pb, Sb and Zn. The roadside topsoil metal concentrations were used to examine correlations between metals and surrounding factors. The studied metals were divided into three groups corresponding to different emission sources: metals from decelerating activities (Cu, Sb and Zn), metals as historical residues from the combustion of petrol (Pb and Cd), and non-source-specific metals (Cr and Ni). It was found that Cu and Sb, despite their rather short history as traffic-emitted metals, have increased more than eightfold in roadside soils compared to background levels. The major source of road traffic related Cu and Sb is brake linings. The significant increase of Cu and Sb in roadside topsoil stresses the need for metal transport studies as well as effect studies of these metals. Metals emitted due to decelerating activities were not correlated to elevated concentrations near road junctions. Emission patterns of traffic-related metals alongside roads are crucial in order to be able to evaluate the optimal localization of storm water treatment ponds.     

Evaluation of the Operational Street Pollution Model Using Data from European Cities

This paper presents a sensitivity analysis and an evaluation of the semi-empirical model known as Operational Street Pollution Model (OSPM). The model is capable of calculating airborne concentrations of exhaust gases emitted by vehicles, within a street canyon. OSPM has been extensively evaluated using data collected over a two year period (1994–1995), during a monitoring campaign carried out in Jagtvej, Denmark. Further evaluation of the model was carried out using data collected in Göttinger Strasse, Hannover (1994) and Schildhorn Strasse, Berlin (1995), both in Germany. In all cases, model runs were carried out for carbon monoxide.Two sets of emission factors were used for the two street canyons in Germany; namely that available within OSPM and another separate set of emission factors derived from data collected in Germany. In the calculation of the latter set, the urban driving patterns and variations in the vehicle fleet composition according to the engine capacity were assumed accordingly. A correlation coefficient of 0.90 between the modelled and measured concentrations was obtained for all the cases considered when using the emission factors of OSPM. A correlation coefficient of about 0.85 was obtained with the newly proposed emission factors when applied to Göttinger and Schildhorn Strasse.     

An Integrated Multicriteria Decision Analysis System for Reducing Air Emissions from Mining Process

The selection of a best alternative method to minimize air pollution and energy consumption for mine sites is a critical task because it encompasses evaluation of different techniques. The aim of this paper is to select most suitable technology for mining system which helps in reducing air pollution and carbon footprints by implementing the multicriteria decision analysis (MCDA) method. The existing methods or frameworks in the mining sector, which have been used in the past to select the sustainable solution, are lacking aid of MCDA, and there is a need to contribute more in this field with a promising decision system. The MCDA method is applied as a probabilistic integrated approach for a mine site in Canada. The analysis involves processing inputs to the Preference Ranking Organization Method for Enrichment Evaluation (PROMETHEE) method which assists in identifying the alternatives, defining the criteria, and thus outranking of the final choice. Moreover, criteria weighting has been determined using analytical hierarchical process (AHP) method. Three categories: reduction of dust/fugitive emission control strategies, reduction in fuel consumption to minimize carbon footprint, and cyanide destruction methods are selected. The probability distributions of criteria weights and output flows are defined by performing uncertainty analysis using the Monte Carlo simulation (MCS). The sensitivity analysis is conducted using Spearman’s rank correlation method and walking criteria weights. The results indicate that the integrated framework provides a reliable way of selecting air pollution control solutions and help in quantifying the impact of different criteria for the selected alternatives.

     

佛山市交通CO2排放及低碳出行对策

以佛山市2012年数据为基础,结合COPERT模型,分析了车型种类、排气量、燃油类型、排放水平等对CO2排放因子的影响规律,探讨了不同车型组成与排放水平下的CO2排放分担率,讨论并评估了佛山市的低碳交通出行对策。结果表明:排放水平对CO2排放因子的影响不明显,除重型客车与公交车,燃油类型对CO2排放因子的影响亦不明显,各车型的CO2排放因子随着排气量的增加而增加;当佛山市机动车平均行驶速度提高至55 km/h时,每辆车CO2综合排放因子可达最小值125.73 g/km;轻型客车和摩托车的CO2排放量最大,分别为1469 493 t/a和394 174.3 t/a,分担率分别为52.1%和14.0%;不同排放水平的载客车CO2排放分担率从大到小排序依次为:国I国0国Ⅱ国Ⅲ国Ⅳ,分别为34.7%、22.0%、21.2%、17.5%及4.6%。     

Modelling of Motor Vehicle Fuel Consumption and Emissions Using a Power-Based Model

The performance of a power based fuel consumption and exhaust emissions model for spark ignition vehicles has been evaluated using a large Australian database derived from testing a wide range of in-use cars on a chassis dynamometer. It was also applied to results of on-road fuel consumption measurement using a "floating" car which was driven back and forth on hilly roadways in Sydney with a length of 8.6 km. The model is found to predict the fuel consumption well over the standard drive cycles and also for the floating car. Average exhaust emissions were also well predicted, but, as would be expected, vehicle-to-vehicle correlation is impossible due to the well-known high variability of emissions between nominally identical vehicles.     

Integrated Traffic and Emission Simulation: a Model Calibration Approach Using Aggregate Information

Environmental impacts of road traffic have attracted increasing attention in project-level traffic planning and management. The conventional approach considers emission impact analysis as a separate process in addition to traffic modeling. This paper first introduces our research effort to integrate traffic, emission, and dispersion processes into a common distributed computational framework, which makes it efficient to quantify and analyze correlations among dynamic traffic conditions, emission impacts, and air quality consequences. A model calibration approach is particularly proposed when on-road or in-lab instantaneous emission measurements are not directly available. Microscopic traffic simulation is applied to generate dynamic vehicle states at the second-by-second level. Using aggregate emission estimation as standard reference, a numerical optimization scheme on the basis of a stochastic gradient approximation algorithm is applied to find optimal parameters for the dynamic emission model. The calibrated model has been validated on several road networks with traffic states generated by the same simulation model. The results show that with proper formulation of the optimization objective function, the estimated dynamic emission model can capture the trends of aggregate emission patterns of traffic fleets and predict local emission and air quality at higher temporal and spatial resolutions.     

Development and Application of Urban High Temporal-Spatial Resolution Vehicle Emission Inventory Model and Decision Support System

This paper reports on the development and application of an urban high temporal-spatial resolution vehicle emission inventory model and decision support system based on the current situation in China and actual vehicle emission control requirements. The system incorporates a user-friendly modular architecture that integrates a vehicle emission model and a decision support platform and includes scenario analysis and visualisation capabilities. A bottom-up approach based on localised emission factors and actual on-road driving condition has been adopted to develop the system. As a case study of application and evaluation, an emission reduction effect analysis of the supposed low-emission zone (LEZ) policy in Beijing (2012) was conducted. According to the simulated results in the forms of tables, histograms and grid maps, the establishment of this LEZ had a definite effect on the emission reduction of various types of air pollutants, especially carbon monoxide and hydrocarbon. In the system, the simulation methodology for identifying environmental benefits brought by the LEZ policy could be used to assess other similar environmental policies. Through flexible modification of configuration values or input data variables, the efficacy of separate or joint policies could be quantifiably evaluated and graphically displayed.     

A combined analysis to identify airborne PM10 sources

A two step procedure that combines an air dispersion model with a receptor model was used to identify the key sources that contribute to air levels of suspended particulate matter. The contribution to PM(10) concentrations measured at four monitoring sites in San Nicolas, Argentina, of the following sources, a thermal power plant, an integrated steel mill, motor vehicle exhaust fumes, and finally dust from paved and unpaved roads, have been analysed. Moreover, an air dispersion model was used to estimate the contribution of the thermal power plant, emissions of which have been described in depth by means of hourly fuel consumption and specific emission factors. The ratio "apportionment coefficient" was introduced to relate the contribution of this source to the measured 24 h PM(10) concentrations by analysing the frequency of occurrence of connecting winds between the power plant and each monitoring site. In San Nicolas 70% of the PM(10) sampled at three of the four monitoring sites could be attributed to the power plant in those scenarios where winds connected the facility's tall point sources with the sampling locations. The contribution to the measured PM(10) levels of the rest of the sources that are present in the analysed area was confirmed by way of receptor models. For this purpose, the multielemental composition of 41 samples was determined by Wavelength Dispersive X-ray Fluorescence analysis. In order to ascertain the underlying correlations between PM(10) samples and potential sources, Principal Component Analysis was performed on the standard matrix of composition profiles, which comprises the measured PM(10) samples being enlarged with the composition profiles of the potential contributing sources. The diagonalization of the covariance matrix was used as a screening procedure to differentiate the most likely contributing sources from those that were not significant.