2-(2-喹啉偶氮)-4-二乙氨基苯甲酸光度法测定镍的研究

合成了新试剂 2 -( 2 -喹啉偶氮 ) -4 -二乙氨基苯甲酸 ( QADEABA) ,并研究了其与镍的显色反应 ,在 p H=8.0的硼酸 -磷酸二氢钾缓冲介质中 ,吐温 -80存在下 ,QADEABA与镍反应生成 2∶ 1稳定络合物 ,λmax=5 90 nm ,ε=1 .1 8× 1 0 5L· mol-1· cm-1。镍含量在 0～ 0 .4 mg/ L内符合比耳定律 ,方法用于水样中镍含量的测定 ,结果令人满意     

5—(4—磺酸基苯偶氮)8—(2,4—二硝基苯氨基)喹啉测定食品中铜的研究应用

在弱碱性介质中 ,5— (4—磺酸基苯偶氮 ) 8— (2 ,4—二硝基苯氨基 )喹啉 (SPDNPAQ)与铜反应生成 2∶ 1紫红色络合物 ,体系 λmax=56 0 nm,ε=1.2 3× 10 5L· mol-1· cm-1。铜含量在 0～ 0 .4 mg/ L内符合比耳定律 ,方法用于一些生物样品和水样中铜的测定。     

重铬酸钾分光光度法测定COD的改进

使用美国HACH公司DR/2010型分光光度计测定COD,需用原装消解液,费用较大。今自配低浓度COD消解液和自建校准曲线代替原装消解液和仪器内存曲线,取得了满意的测定结果。1　试验自配消解液:C(1/6K2Cr2O7)=0 104mol/L重铬酸钾溶液与硫酸-硫酸银溶液以1∶5体积比混合摇匀。其他试剂、仪器及试验步骤均同文献[1]。2　结果与讨论2 1　校准曲线的绘制采用300mg/LCOD标准溶液,绘制标准曲线,得线性回归方程:y=2 25×10-3-3 43×10-3x,γ=-0 9997。2 2　精密度配制15 0mg/L、45 0mg/L和75 0mg/LCOD标液,用自配消解液和自建校准曲线进行…     

分光光度法测定环境水样中镁的研究

研究了4-(2-羟基-4-硝基苯偶氮)-1-苯基-3-甲基吡唑啉酮(HNAPMP)与镁的显色反应,在硼砂—氢氧化钠(pH=10)缓冲介质中,乳化剂-OP存在下,HNAPMP与镁反应生成2∶1稳定络合物,λmax为525nm,ε为3 63×104L·mol-1·cm-1。镁含量在0—0 8mg/L内符合比耳定律,方法用于环境水样中镁的测定,结果令人满意。     

番红花红T紫外分光光度法测定微量亚硝酸盐氮

1实验方法 :于 2 5ml比色管中加 5μg亚硝酸盐氮标准使用液 ( 5.0 μg/ml)、2 .0 ml1 .0× 1 0 -3mol/L 番红花红 T、4 .0 ml2 .0 mol/L 缓冲溶液( H2 SO4) ,用水定容 ,摇匀。放置 1 0 min,用 1 cm比色皿以试剂空白为参比在 365nm处测吸光度 ,吸光值至少在 1 h内保持恒定。 2变异系数 0 .59%～ 1 .35% ,加标回收率 98.2 %～ 1 0 0 .4 %。 3亚硝酸盐氮在 0～ 1 0 .0 μg/2 5ml内符合比耳定律 ,表观摩尔吸光系数 3.1× 1 0 4L/mol· cm,回归方程y=0 .0 2 67c 0 .0 0 2 ,相关系数 r=0 .9992 ,结果满意。番红花红T紫外分光光度法测定微量亚…     

4-氨基安替吡啉法测定水中高浓度挥发酚

取 2 50 ml含酚水样的蒸馏液于 50 0 ml分液漏斗中 ,加入 2 .0 ml缓冲溶液混匀 ,此时 p H为1 0 .0± 0 .2。加入 1 .5ml2 % 4 - AAP溶液混匀 ,再加 1 .5ml铁氰化钾溶液混匀。做一试剂空白 ,然后均以蒸馏水为参比 ,显色 1 5min用 1 cm比色皿于波长 51 0 nm处测吸光度。含酚 0～ 50 0 (μg/2 50 ml)时符合比耳定律 ;摩尔吸光系数 1 .2 6×1 0 4L/mol· cm,灵敏度较高 ;检出限为 0 .0 75mg/L;相对标准误差 2 .75% ;回收率 92 .5～ 96 .7( % )。本法在经过显色剂显色后确定水样为高浓度时 ,只需对其直接比色即可测出挥发酚浓度 ,避免重复工作…     

2-羟基-5-磺酸基苯基重氮氨基偶氮苯光度法测定微量Ni(Ⅱ)的研究

2—羟基— 5—磺酸基苯基重氮氨基偶氮苯与 Ni( )在 OP存在下 ,于 p H=1 0的硼砂缓冲溶液中形成 2∶ 1红色络合物 ,λmax=530 nm,ε=6.0× 1 0 4 L· mol- 1·cm- 1 ,Ni( )含量在 0～ 0 .2 4 mg/ L符合比耳定律。用于电镀废水中镍的测定 ,结果满意。     

HPLC法测定饲料中维生素A、维生素D 3 和维生素E

建立了以w(C2H5OH)=95 %乙醇直接提取,高效液相色谱仪在波长280 nm和254 nm处连续测定饲料中维生素A、维生素D3和维生素E的方法.色谱柱为大连依利特Hypersil ODS C18(25 cm×4.6 mm×5 μm),流动相为甲醇-水,流速为1.2 mL/min.维生素A、维生素D3、维生素E的质量浓度分别在1.0 mg/L～20.0 mg/L、0.5 mg/L～15.0 mg/L 、2.5 mg/L～50.0 mg/L范围内与峰面积呈良好的线性关系,检测限分别为0.3×10-6 μg、0.04×10-6 μg、5.0×10-6 μg,相对标准偏差分别为1.6 %、2.7 %、2.4 %,平均回收率分别为99 %、102 %、98 %.     

双硫腙-CTMAB光度法测定锌的研究

在硼砂 -氢氧化钠缓冲溶液 (p H=1 1 .0 )中 ,溴化十六烷基三甲胺 (CTMAB)存在下双硫腙与锌生成可溶于水的 2∶ 1红色络合物 ,λmax=540 nm ,ε=7.3 0× 1 0 4 L· cm-1· mol-1,锌含量在 0～ 0 .6mg/L内符合比耳定律。本法可用于水样中锌含量的测定     

间磺酸基偶氮安替比林光度法测定Ni(Ⅱ)的研究

间磺酸基偶氮安替比林与Ni(Ⅱ )在pH =4 .0～ 6.0HAc -NaAc缓冲溶液中形成 1∶1蓝色络合物 ,λmax=630nm ,ε=5 .4 5× 1 0 4 L·mol- 1·cm- 1,Ni(Ⅱ )含量在 0～ 0 .30mg/L符合比耳定律。用于电镀废水中镍的测定 ,结果满意     

4—（H—酸偶氮）—1—苯基—3—甲基吡唑酮光度法测定铜的研究及应用

合成了新试剂４－（Ｈ－酸偶氮）１－苯基－３－甲基吡唑酮（ＨＰＭＰ）,研究了其和铜的显色反应。在ｐＨ＝７的ＮＨ４Ａｃ缓冲介质中,ＣＴＭＡＢ存在下,ＨＰＭＰ与Ｃｕ（Ⅱ）生成２∶１紫色络合物,λｍａｘ＝５８０ｎｍ,ε＝５．６８×１０４Ｌ·ｍｏｌ－１·ｃｍ－１。铜含量在０～０．６ｍｇ／Ｌ内符合比耳定律。方法用于水样和生物样品中铜的测定,结果令人满意。     

氯仿,四氯化碳对蚕豆根尖细胞微核诱发效应的比较研究

利用蚕豆根尖细胞微核方法检测氯仿、四氯化碳的诱变效应，结果表明，氯仿从０．０１ｇ／Ｌ至１．０各浓度组微核率明显高于阴性对照组（Ｐ〈０．０１），亦高于阳性对照组（Ｐ〈０．０１），四氯化碳从０．０１ｇ／Ｌ至１．０ｇ／Ｌ各浓度组微核率同样明显高于阴性及阳性对照组（Ｐ〈０．０１），且同一浓度的２种药物诱发微核率比较，氯仿高于四氯化碳，差异非常显著，说明氯仿的诱变活性强于四氯化碳。     

Biomonitoring of testate amoebae (protozoa) as toxic metals absorbed in aquatic bryophytes from the Hg-Tl mineralized area (China)

A new method has been developed for the determination of chemical oxygen demand (COD) in pulping effluent using chemometrics-assisted spectrophotometry. Two calibration models were established by inducing UV-visible spectroscopy (model 1) and derivative spectroscopy (model 2), combined with the chemometrics software Smica-P. Correlation coefficients of the two models are 0.9954 (model 1) and 0.9963 (model 2) when COD of samples is in the range of 0 to 405 mg/L. Sensitivities of the two models are 0.0061 (model 1) and 0.0056 (model 2) and method detection limits are 2.02?C2.45 mg/L (model 1) and 2.13?C2.51 mg/L (model 2). Validation experiment showed that the average standard deviation of model 2 was 1.11 and that of model 1 was 1.54. Similarly, average relative error of model 2 (4.25%) was lower than model 1 (5.00%), which indicated that the predictability of model 2 was better than that of model 1. Chemometrics-assisted spectrophotometry method did not need chemical reagents and digestion which were required in the conventional methods, and the testing time of the new method was significantly shorter than the conventional ones. The proposed method can be used to measure COD in pulping effluent as an environmentally friendly approach with satisfactory results.     

Investigations on boron levels in drinking water sources in China

To evaluate boron contamination of public drinking water in China, both dissolved and total boron contents in 98 public drinking water sources from 49 cities, 42 brands of bottled water samples from supermarkets in several cities, and 58 water samples from boron industrial area were measured by inductively coupled plasma-mass spectrometry (ICP-MS). Our experimental results showed that boron existed in public drinking water sources mainly in dissolved status with total concentrations ranging from 0.003 to 0.337 mg/L (mean = 0.046 mg/L). The mean boron concentrations in mineral and pure bottled water were 0.052 and 0.028 mg/L, respectively. The results obtained in this work showed that there was no health risk on view of boron in public drinking water sources and bottled water. In boron industrial area, boron concentrations in surface water and ground water were 1.28 mg/L (range = 0.007–3.8 mg/L) and 18.3 mg/L (range = 0.015–140 mg/L), respectively, which indicated that boron industry caused boron pollution in local water system.     

Physicochemical quality of an urban municipal wastewater effluent and its impact on the receiving environment

The physicochemical qualities of the final effluents of an urban wastewater treatment plant in South Africa were assessed between August 2007 and July 2008 as well as their impact on the receiving watershed. The pH values across all sampling points ranged between 6.8 and 8.3, while the temperature varied from 18°C to 25°C. Electrical conductivity (EC) of the samples was in the range of 29–1,015 μS/cm, and turbidity varied between 2.7 and 35 NTU. Salinity and total dissolved solids (TDS) varied from 0.36 to 35 psu and 16 to 470 mg/L, respectively. The concentrations of the other physicochemical parameters are as follows: chemical oxygen demand (COD, 48–1,180 mg/L); dissolved oxygen (DO, 3.9–6.6 mg/L); nitrate (0.32–6.5 mg NO $_{3}^{-}$ as N/L); nitrite (0.06–2.4 mg NO $_{2}^{-}$ as N/L); and phosphate (0.29–0.54 mg PO $_{4}^{3-}$ as P/L). pH, temperature, EC, turbidity, TDS, DO, and nitrate varied significantly with season and sampling point (P?<?0.05 and P?<?0.01, respectively), while salinity varied significantly with sampling point (P?<?0.01) and COD and nitrite varied significantly with season (P?<?0.05). Although the treated effluent fell within the recommended water quality standard for pH temperature, TDS, nitrate and nitrite, it fell short of stipulated standards for other parameters. The result generally showed a negative impact of the discharged effluent on the receiving watershed and calls for a regular and consistent monitoring program by the relevant authorities to ensure best practices with regard to treatment and discharge of wastewater into the receiving aquatic milieu in South Africa.     

Characterization of Rain and Roof Drainage Water Quality in Xanthi, Greece

Thirteen field campaigns were undertaken in the period from December 2, 2002 until September 1, 2004 to collect water samples in order to characterize the quality of rainfall and roof drainage in the city of Xanthi, a typical provincial city in Greece. In each campaign, water samples were collected from 10 representative sites in the city (in total 130 samples), representing areas of distinct land use and human activities (i.e., traffic volume, residence density and industrial activity). The water samples were analyzed according to drinking water criteria for total coliform (not detected), temperature (range: 0.9–20°C), pH (range: 3.6–11.4), alkalinity (range: 0–21.5 mg CaCO₃/L), nitrate (range: 0–2456 μg/L), ammonium (range: 0–2628 μg/L), sulfate (range: 0–0.5 mg/L), calcium (range: 259.1–3064 μeq/L), magnesium (range: 0.8–488.8 μeq/L), potassium (range: 0.0–110.6 μeq/L) and dissolved heavy metals (Fe, range: 0.01–0.18 mg/L; Mn, range: 0.01–0.09 mg/L; Zn, range: 0.01–0.54 mg/L; Cu, Cr and Ni, not detected). Pollutant concentrations were generally higher in roof drainage than in rainwater, but both were lower than drinking water standards. Dissolved heavy metal concentrations were generally higher in the areas of intensive human activities, such as roads with high traffic volume and densely populated residential areas. The satisfactory quality of rainwater, which results from this analysis, makes its use as grey water possible.     

Determination of Cadmium Levels in Agricultural Areas of Çarşamba and Bafra Plains

Cadmium pollution resulted from fertilizer applications were studied by determining cadmium levels in agricultural and non-agricultural soils of Bafra and Çar?amba plains. Soil samples of 68 were collected from agricultural (34) and non-agricultural (34) areas. The sample of 2 g was placed in a test tube and digested with hydrochloric acid and nitric acid mixture (3:1, v/v) in an aluminum block. Taking up the evaporated residue was dissolved in 1% nitric acid and total cadmium concentrations were determined with GF-AAS. Mean level of cadmium contents were found in agricultural areas 0.162?±?0.078 for Çar?amba and 0.433?±?0.288 mg kg^?1 for Bafra. The accuracy of the method was tested with determining cadmium contents of standard reference material and cadmium spiked soil samples.     

微乳液介质 - 4- (6- 甲氧基 - 8- 喹啉偶氮 )- 间苯三酚分光光度法测定微量铜

研究了溴代十六烷基吡啶、正丁醇、正庚烷和水自制微乳溶液介质中,4-（6-甲氧基-8-喹啉偶氮）-间苯三酚与铜的显色反应,建立了分光光度法测定微量铜的新方法。在显色液中铜的质量浓度在0.010 mg/L～0.700 mg/L范围内符合比尔定律,方法检出限为0.003 mg/L,铝合金和水样测定的RSD为0.3%～1.7%,加标回收率为96.3%～104%。     

气相分子吸收光谱法在海水无机氮测定中的适用性研究

为探究气相分子吸收光谱法在海水无机氮测定中的适用情况,在检出限的10～20倍、30～50倍、50～100倍3个浓度范围内开展了准确度、加标回收率和方法比对试验。结果表明,采用气相分子吸收光谱法测定海水亚硝酸盐氮(0～0.100 mg/L)、硝酸盐氮(0～0.400 mg/L)、氨氮(0～0.200 mg/L)时,标准曲线均具有很好的线性,线性拟合度均在0.999 3以上,检出限依次为0.000 8、0.004、0.004 mg/L,且该方法不具有盐效应,适用于海水样品的检测。当样品浓度太低时,气相分子吸收光谱法测定结果的准确度较低,因此,建议仅在亚硝酸盐氮浓度高于0.030 mg/L、硝酸盐氮浓度高于0.100 mg/L、氨氮浓度高于0.090 mg/L时使用该方法,对应的海域为河口及近岸等无机氮含量较高的海域。此外,为保证测定结果的准确度,每个样品需平行测定2～3次。     

刚果红-巯基棉分离富集光度法测定垃圾渗滤液中镉

基于在pH值为4.0～5.2的BR缓冲介质中，镉与刚果红发生显色反应并生成蓝色离子缔合物的原理，建立了测定垃圾渗滤液中镉的巯基棉分离富集光度法。其最大正吸收波长和最大负吸收波长分别为604nm和492nm，线性范围分别为0.10mg／L～2.80mg／L和0.10mg／L～3．40mg／L，采用双波长叠加测定灵敏度更高。探讨了渗滤液的处理方法及共存离子对测定的影响，优化了试验条件，实际样品的测定结果与原子吸收法对比无显著差异，加标回收率为98，6％～104％。