基于改进火焰原子吸收光谱的土壤六价铬分析

针对分离和萃取环节,对火焰原子吸收光谱测定土壤中六价铬的方法加以改进。采用聚合氯化铝为絮凝剂、异戊醇为萃取剂,使三价铬和六价铬有效分离,并减少了测试干扰。考察了聚铝试剂用量和萃取液振荡时间对测定的影响,并将该方法与EPA 3060A方法和未改进的火焰原子吸收光谱法比较,表明改进后的方法能用于土壤中六价铬的测定。     

碳酸氢钠浸提-钼锑抗分光光度法测定土壤中的有效磷

用0.50 mol/L碳酸氢钠溶液浸提中性和石灰性土壤中的有效磷.碳酸氢钠可以抑制溶液中Ca2+的活度,使某些活性较大的磷酸钙盐被浸提出来,同时也可使活性磷酸铁、铝盐水解而被浸出.浸提液与钼锑抗显色剂反应生成磷钼蓝,在波长880 nm处测量吸光度.当取样量为2.50 g时,使用50 mL碳酸氢钠溶液浸提,使用1 cm比...     

氯化钡浸提法测定土壤可交换酸度

建立了氯化钡浸提测定酸性土壤可交换酸度的方法，优化了水土比、土壤粒度、浸提液质量浓度、浸提次数、震荡时间等试验参数。方法检出限为0．016cmol／kg，经重复性和再现性检验表明精密度良好。该方法可同时用于土壤可交换性氢和可交换性铝的测定。     

铋磷钼蓝分光光度法测定土壤中磷含量

土壤中磷含量的分析是土壤环境监测的主要项目之一.建立了铋磷钼蓝分光光度法测定土壤中磷含量的新方法,与现有的《土壤全磷测定方法》(GB 9837-88)和土壤总磷快速检测仪方法进行了比较讨论.方法的检出限为5.0 mg/kg,对磷含量为475 mg/kg和292 mg/kg的标准土壤样品进行测定,结果与标准值吻合,其相对...     

等离子发射光谱法测定铝在驻马店市地表水铝含量调查中的应用

按照地表水监测技术规范(HJ/T91-2002),对驻马店市地表水体进行采样,用等离子体发射光谱法两条铝分析线,对所采各个断面水样中的铝浓度进行分析测定,分析得出了流域内地表水中铝含量的一般特征,为下一步地表水体环境质量标准中增设铝项目的管理提供技术支持。     

异丙醇增感电感耦合等离子体质谱法直接测定土壤和沉积物中硒

提出了沸水浴混合酸法消解,以异丙醇为增感剂,电感耦合等离子体质谱直接测定土壤和沉积物中硒的方法。实验表明2mol/L硝酸-4mol/L盐酸混酸能有效溶出土壤和沉积物中各种形态的硒。相对于1%硝酸基体,4%(V/V)异丙醇基体中硒的ICP-MS响应值提高了12.1倍;而且4%(V/V)异丙醇基体可有效抑制硒的质谱干扰。ICP发射功率和雾化气流速是影响异丙醇在ICP-MS测定过程增敏效应的主要因素。以78硒为测定同位素,方法检出限为0.005mg/kg,实际样品测定精密度均小于5%。用于测定土壤和沉积物国家标准样品并对其消解液进行加标回收实验,结果令人满意。     

GC-MS/MS法测定石油污染土壤中的多环芳烃

采用丙酮-正己烷混合溶液(体积比为1∶1)提取石油污染土壤样品中10种典型多环芳烃,用GC-MS/MS法测定。通过优化前处理和测定条件,使方法在0.100 mg/L～10.0 mg/L范围内线性良好,方法检出限为5.00μg/kg～15.8μg/kg。土壤样品加标回收试验6次测定结果的RSD为0.1%～16.6%,加标回收率为43.1%～109%。将该方法用于测定湖南某石化项目周边的实际土壤,结果表明该地区不同点位土壤中多环芳烃测定值为未检出～300μg/kg,在国家标准规定的范围内。     

土壤中挥发性有机物的快速测定方法

本文建立了用便携式气相色谱-质谱仪快速测定土壤中VOCs的方法。该方法能够快速对土壤样品中VOCs进行定性分析和定量测定。当采样量达到5 g时,方法检出限0.02~2.11μg/L,相对标准偏差2.0%~13.5%;加标20μg/L时,回收率63%~123%。采用该方法测定北京地区5个土壤样品,总体质量浓度为0~873μg/kg。     

微波消解-氢化物发生-原子荧光法测定土壤中的砷

以微波消解的方法处理土壤样品,采用硝酸—盐酸作为消解体系,设定最佳的样品前处理条件,使用水浴温恒加速砷的还原速率,同时利用仪器自动配置标准曲线。同时设定仪器最优测定条件,再用双道原子荧光光谱法测定土壤样品中的砷。通过国家标准参考物质和加标回收试验,对方法进行验证。结果表明,采用该方法,砷的浓度范围在2.00～20.00μg/L时校正曲线呈线性,检出限为0.003mg/Kg,测定土壤标准物质,砷测定结果均在标准值允差范围内, RSD范围为1.31%,测定土壤中砷的回收率为106.6%。说明该方法稳定性好、精密度高、操作简便、成本低,适用于高效测定大量土壤样品中砷含量。     

加速溶剂萃取-凝胶净化色谱-气相色谱质谱法测定农用地土壤中有机氯农药方法研究

通过对加速溶剂萃取、平行蒸发及净化方法等环节的优化实验,建立了加速溶剂萃取-凝胶净化色谱-气相色谱质谱法测定农用地土壤中23种有机氯农药的检测方法。结果表明,方法检出限为0.0034~0.0052 mg/kg;对化合物质量分数为0.25 mg/kg的土壤加标样品进行平行实验,回收率为82.0%~93.7%;测定结果的相对标准偏差（RSD）≤8.7%。对土壤有证标准质控样品进行分析,测定结果均在验收范围之内。该方法准确可靠,灵敏度较高,样品净化效果较好,能够满足农用地土壤中有机氯农药残留痕量分析的要求。     

铁和铝离子对土壤水溶性氟化物检测的干扰研究

通过离子选择电极法测定Fe3+和Al3+不同含量的土壤样品中水溶性氟化物试验,研究Fe3+和Al3+对测定的干扰与消除方法,证实了在总离子强度调节缓冲溶液共存下,Fe3+和Al3+对土壤提取液中水溶性氟化物检测结果存在不同程度的负干扰。选择6种代表性土壤样品,在水溶性氟化物提取液中加入20 mg/L的Al3+和100 mg/L的Fe3+做干扰试验,比较了分取不同体积土壤提取液对氟化物检测结果的影响,结果表明,对水溶性ρ(Fe3+)和ρ(Al3+)高的土壤样品,可选择减少提取液取样体积来消除干扰。选取的5种标准样品测试结果与标准值相符,干扰消除方法具有良好的适用性。     

铬污染土壤中六价铬的测定

研究了土壤中Ｃｒ＾６＋的提取测定方法。结果表明，用０．４ｍｏｌ／Ｌ ＫＣｌ为提取剂，离心分离提取液，可简单，快速，准确地测定土壤中Ｃｒ＾６＋，所建立的方法适用于北方偏碱性土壤。     

Evaluating Controlling Factors to Ali/(Ca + Mg) Molar Ratio in Acidic Soil Water, Southern and Southwestern China: Multivariate Approach

Al_i/(Ca + Mg) molar ratio in soil water has been used as an indicator to the effects of acid deposition on terrestrial ecosystems. However, the main factors controlling this ratio have not been well documented in southern and southwestern China. In this study, we presented the variation in inorganic aluminum (Al_i) and Al_i/(Ca + Mg) molar ratio in different sites and soil horizons based on two to three years monitoring data, and evaluated the main factors controlling Al_i/(Ca + Mg) molar ratio using principle component analysis (PCA) and partial least square (PLS) regression. Monitoring data showed although Al_i/(Ca + Mg) molar ratios in most soil water were lower than assumed critical 1.0, higher molar ratios were found in some soil water at TSP and LXH site. Besides acid loading, both soil properties and soil water chemistry affected the value of Al_i/(Ca + Mg) molar ratio in soil water. Partial least square (PLS) indicated that they had different relative importance in different soil horizons. In A-horizon, soil aluminum saturation (AlS) had higher influence on Al_i/(Ca + Mg) molar ratio than soil water chemistry did; higher soil aluminum saturation (AlS) led to higher Al_i/(Ca + Mg) molar ratio in soil water. In the deeper horizons (i.e., B₁-, B₂- and BC-horizon), inorganic aluminum (Al_i) in soil water had more and more important role in regulating Al_i/(Ca + Mg) molar ratio. On regional scale, soil aluminum saturation (AlS) as well as cation exchange capacity (CEC) was the dominant factor controlling Al_i/(Ca + Mg) molar ratio. This should be paid enough attention on when making regional acid rain control policy in China.     

Solid phase extraction of gold(III) on silica gel modified with benzoylthiourea prior to its determination by flame atomic absorption spectrometry

A new method has been developed for the determination of gold based on separation and preconcentration using silica gel modified with benzoylthiourea. The optimum experimental parameters for preconcentration of gold, such as acid concentration, sample flow rate, eluent and matrix ions, have been investigated. Gold could be quantitatively retained in the 0.25-2.0 mol L(-1) HCl and HNO(3) concentrations, and then eluted completely with 0.5 mol L(-1) thiourea in 1.0 mol L(-1) HCl. The sorption capacity of gold(III) is 0.92 +/- 0.04 mmol g(-1) with a high enrichment factor of 267. The relative standard deviation of the method, RSD%, was found as 1.2% for 0.1 microg mL(-1). The detection limit for gold was 1.4 microg L(-1). The validation of the proposed method was checked by the analysis of certified reference soil materials. The presented procedure was applied to the determination of gold in some environmental samples.     

Monitoring of copper level in water and soil samples by using liquid–liquid extraction

A new, simple, sensitive, and selective spectrophotometric method for the determination of copper in water and soil samples has been demonstrated. The method is based on the reaction of Cu(I) with neocuproine (2,9-dimethyl-1, 10-phenanothroline) and extracted with N-phenyl benzimidoylthiourea in chloroform. The value of molar absorptivity of the complex in the term of Cu(I) is 1.45 × 10⁵ L mol^???1 cm^???1 at λ _max 460 nm in chloroform. The detection limit of copper in water and soil is 2 ng mL^???1 and 4 ng g^???1, respectively. The method is free from the interference of the ions commonly found to be associated with the copper determination in water and soil samples. The application of the proposed method has been successfully tested for the determination of copper in different types of water and soil samples.     

石墨炉原子吸收法测定环境空气中的锡

研究了硝酸-双氧水体系消解、石墨炉原子吸收法测定环境空气中锡的方法.采用抗坏血酸和磷酸二氢铵作混合基体改进剂,热解涂层石墨管,塞曼扣背景.方法的检测限为3.56 μg/L,实际样品回收率为90.6％～102％.     

Propanil in a Manitoba soil: an interactive spreadsheet model based on conventional chemical kinetics

An interactive spreadsheet model has been created for quantitative predictions of propanil sorption and reaction in a slurried Manitoba clay soil. Based on experimental values for the numbers of empty and filled sorption sites as reactants and products, the reaction mechanism has been described with conventional chemical kinetics. The on line HPLC μ extraction method revealed labile sorption, intraparticle diffusion, and a chemical reaction. Laidler's integral rate law for second order kinetics describes the labile sorption. Desorption, intraparticle diffusion, and the chemical reaction are all described by first order kinetics. The time dependent effects of initial concentration and amount of slurried soil can be predicted for sorption, intraparticle diffusion, and the amount of reaction product. Suggested applications include storm runoff and inputs for fate and transport hydrology models.     

Assessment of aluminum bioavailability in alum sludge for agricultural utilization

Inorganic aluminum ions, [Al(H₂O)₆]³⁺, [Al(OH)(H₂O)₅]²⁺, and [Al(OH)₂(H₂O)₄]⁺, are toxic to a number of crops. The aim of this study was to estimate the danger of soil contamination of bioavailable aluminum and heavy metals forms because of alum sludge which was a by-product of water, and wastewater treatment technology using aluminum coagulant is introduced into the soil. Aluminum and selected heavy metal fractionation was carried out in the post-coagulation sludge collected at a water treatment plant (where aluminum was used as a coagulant), fermented sewage sludge at a municipal wastewater treatment plant (which did not apply aluminum coagulant), and soil from water treatment plant as well as the mixtures of sludge and soil. It has been found that post-coagulation sludge used as natural fertilizer is a secondary source of bioavailable aluminum, especially when aluminum coagulants are used during water and wastewater treatment. The evaluation of applicability of the sludge to very weak acidic and acidic agricultural soils was carried out. The authors shall debate the question whether, in this case, the Regulation of EU and Polish Government on sewage sludge should also take the bioavailable aluminum into account and add to the list of the elements whose allowable contents are limited.     

Simultaneous derivatization and extraction of nitrophenols in soil and rain samples using modified hollow-fiber liquid-phase microextraction followed by gas chromatography–mass spectrometry

A simple and sensitive method based on a modified hollow-fiber liquid-phase microextraction followed by gas chromatography–mass spectrometry has been successfully developed for the extraction and simultaneous derivatization of some nitrophenols (NPs) in soil and rain samples. Microwave-assisted solvent extraction was used for the extraction of NPs from the soil, while the rain sample was directly applied to the previously mentioned method. Briefly, in this method, the analytes were extracted from aqueous samples into a thin layer of organic solvent (dodecane?+?10 % tri-n-octylphosphine oxide) sustained in the pores of a porous hollow fiber. Then, they were back-extracted using a small volume of organic acceptor solution (25 μl; 10 mg/L N-methyl-N-(trimethylsilyl)trifluoroacetamide, as derivatization reagent, in acetonitrile) that was located inside the lumen of the hollow fiber. Under the optimized extraction conditions, enrichment factors of 255 to 280 and limits of detection of 0.1 to 0.2 μg/L (S/N?=?3) with dynamic linear ranges of 1–100 μg/L were obtained for the analytes. The accuracy of the approach was tested by the relative recovery experiments on spiked samples, with results ranging from 93 to 113 %. The method was shown to be rapid, cost-effective, and potentially interesting for screening purposes.