Dust explosion risk moderation for flocculent dusts

The research presented in this paper is focused on dust explosions of coarse and fine flocculent (or fibrous) samples of wood and polyethylene. Hybrid mixtures of fibrous polyethylene and admixed ethylene were also studied. Experimentation was conducted by following standardized test procedures and using standardized apparatus for determination of maximum explosion pressure, size-normalized maximum rate of pressure rise, minimum explosible concentration, minimum ignition energy, and minimum ignition temperature. A general trend was observed of enhanced explosion likelihood and consequence severity with a decrease in material diameter, as well as enhanced consequence severity with admixture of a flammable gas to the combustion atmosphere. The same phenomena are well-established for dusts composed of spherical particles; this highlights the importance of inherently safer design and the principle of moderation in avoiding the generation of fine sizes of flocculent dusts and hybrid mixtures of such materials with flammable gases.In addition to presenting experimental findings, the paper describes phenomenological modelling efforts for the flocculent polyethylene using four geometric equivalence models: radial equivalence, volumetric equivalence, surface area equivalence, and specific surface area equivalence. The surface area equivalence model was found to yield the best estimates of maximum rate of pressure rise for the flocculent polyethylene samples investigated experimentally.     

The effect of admixed material on the minimum explosible concentration of oil shale

The minimum explosible concentration (MEC) in the air atmosphere at the boundary between an explosion and no explosion in a dust cloud, has been investigated for several particle sizes of oil shale and for mixtures of oil shale and inert powder of different particle size. Limestone, stone dust and coarse particle size of oil shale were used as inert materials. Measurements were made in a standard small vertical tube apparatus. The results obtained indicated that the minimum explosible concentration is dependent on the particle size, i.e., values of MEC decrease with a decrease in the size of the particles. Below 70 μm, values of MEC become almost constant. Admixture of limestone as low as 5% to oil shale is sufficient to reduce the MEC values significantly.     

The influence of initial conditions on the propagation of smouldering fires in dust accumulations

A mathematical model is presented which allows one to treat the combined phenomena of heat, mass and species transfer by diffusion as they occur within smouldering fires in accumulations of dust or other solid bulk materials. The model was applied to predict self-ignition temperatures of five different dusts, where it could be shown that computed and experimental self-ignition temperatures coincide within an error margin of ±5%.

For smouldering fires, if initiated by either self-ignition or an ignition source, it could be shown that the temperature and the velocity at which the reaction front propagates both depend on the volume of the dust accumulation. In addition, the propagation velocity increases when the initial temperature of the dust accumulation is increased and decreases when the initial moisture content of the dust accumulation is increased.

Comparisons of the numerical model with experiments show that the smouldering propagation is mirrored qualitatively, while the accuracy of the computations strongly depends on the accuracy of the input parameters, namely on the apparent activation energy.     

Experimental investigation on explosion flame propagation of wood dust in a semi-closed tube

In order to explore flame propagation characteristics during wood dust explosions in a semi-closed tube, a high-speed camera, a thermal infrared imaging device and a pressure sensor were used in the study. Poplar dusts with different particle size distributions (0–50, 50–96 and 96–180 μm) were respectively placed in a Hartmann tube to mimic dust cloud explosions, and flame propagation behaviors such as flame propagation velocity, flame temperature and explosion pressure were detected and analyzed. According to the changes of flame shapes, flame propagations in wood dust explosions were divided into three stages including ignition, vertical propagation and free diffusion. Flame propagations for the two smaller particles were dominated by homogeneous combustion, while flame propagation for the largest particles was controlled by heterogeneous combustion, which had been confirmed by individual Damköhler number. All flame propagation velocities for different groups of wood particles in dust explosions were increased at first and then decreased with the augmentation of mass concentration. Flame temperatures and explosion pressures were almost similarly changed. Dust explosions in 50–96 μm wood particles were more intense than in the other two particles, of which the most severe explosion appeared at a mass concentration of 750 g/m³. Meanwhile, flame propagation velocity, flame propagation temperature and explosion pressure reached to the maximum values of 10.45 m/s, 1373 °C and 0.41 MPa. In addition, sensitive concentrations corresponding to the three groups of particles from small to large were 500, 750 and 1000 g/m³, separately, indicating that sensitive concentration in dust explosions of wood particles was elevated with the increase of particle size. Taken together, the finding demonstrated that particle size and mass concentration of wood dusts affected the occurrence and severity of dust explosions, which could provide guidance and reference for the identification, assessment and industrial safety management of wood dust explosions.     

Minimum Ignition Temperature of layer and cloud dust mixtures

The prevention of dust explosions is still a challenge for the process industry. Ignition, in particular, is a phenomenon that is still not completely understood. As a consequence, safety conditions pertaining to ignition suppression are rarely identified to an adequate level. It is well known that, in general, the ignition attitude of a dust depends on several factors, such as the nature of the chemical, the particle size, moisture content, etc., but there is still a lack of knowledge on the effect of the single variables.This paper has the aim of providing data on the Minimum Ignition Temperatures of dust mixtures obtained from a mixing of a combustible dust (flour, lactose, sucrose, sulphur) and an inert dust (limestone, extinguishing powders) as well as from the mixing of two different combustible dusts. Various mixtures with different weight ratios have been tested in a Godbert Greenwald (GG) furnace and on a hot plate in order to measure the effect of mixture composition on the Minimum Ignition Temperature (MIT_L) of the layer and on the Minimum Ignition Temperature (MIT_C) of the cloud. In order to further verify the effects of inert dust particle size, inerts sieved to different size ranges have been tested separately. Generally, both MIT_L and MIT_C increase as the inert content is increased. MIT_C is poorly affected by inert particle size when limestone is used. The MIT_L of pure flour is higher than the MIT_L of mixtures containing up to 40% of 32–75 μm of limestone. This was probably due to the behaviour of pure flour during the test, which demonstrated strong tendency to produce char, cracks in the layer and detachment from the hot plate.     

Explosibility of fine graphite and tungsten dusts and their mixtures

To evaluate the explosion hazard of ITER-relevant dusts, a standard method of 20-l-sphere was used to measure the explosion indices of fine graphite and tungsten dusts and their mixtures. The effect of dust particle size was studied on the maximum overpressures, maximum rates of pressure rise, and lower explosive concentrations of graphite dusts in the range 4 μm to 45 μm. The explosion indices of 1 μm tungsten dust and its mixtures with 4 μm graphite dust were measured. The explosibility of these dusts and mixtures were evaluated. The dusts tested were ranked as St1 class. Dust particle size was shown to be very important for explosion properties. The finest graphite dust appeared to have the lowest minimum explosion concentration and be able to explode with 2 kJ ignition energy.     

Moderation of dust explosions

Inherent safety is a proactive approach to process safety in which hazards are removed or minimized so as to reduce risk without engineered (add-on) or procedural intervention. Four basic principles are available to attain an inherently safer design—minimization, substitution, moderation, and simplification. The subject of the current paper is the principle of moderation as it applies to the prevention and mitigation of dust explosions.

Moderation can be achieved by processing a material under less severe operating conditions or by processing the material in a less hazardous form. With respect to the latter approach, it may be possible to alter the composition of a dust by admixture of solid inertants, or to increase the dust particle size so as to decrease its reactivity. Additionally, avoidance of the formation of hybrid mixtures of explosible dusts and flammable gases is an application of moderation of the material hazard.

Several examples are given for each of the above three forms of moderation. The discussion on admixture of solid inertants includes examples from the following industrial applications: (i) refractory materials manufacturing, (ii) food processing, (iii) power generation, (iv) industrial recycling, and (v) foundry shell mold fabrication. The importance of particle size consideration is explained first from the perspective of engineering tools such as the Dow Fire & Explosion Index, and professional guidance on the definition of a dust and suitable particle sizes for explosibility testing. Industrial examples are then drawn from the following areas: (i) rubber recycling and textile manufacturing, (ii) industrial recycling, (iii) wood processing, (iv) dry additive handling (polyethylene facility), (v) polyethylene production, (vi) carbon block recycling, and (vii) coal mining. The concluding discussion on hybrid mixtures includes brief cases from the process safety literature.     

固体惰性介质对煤粉爆炸压力的影响研究

通过对固体惰性介质在减轻煤粉爆炸作用的实验研究,给出影响固体惰化剂作用效果的主要影响因素。实验分别选用来自加拿大和中国的3种煤粉和石灰石,对每种实验样品的成分、粒度都进行分析。用20L球形容器进行实验,测定煤粉中加入不同含量的石灰石后煤粉爆炸的Pmax和(dp/dt)max值。结果表明,石灰石能够起到减轻煤粉爆炸影响的作用,并且随着煤粉粒度的减小,要达到相同的抑爆效果需要的石灰石的用量将加大。     

Minimum ignition energy of mixtures of combustible dusts

Most industrial powder processes handle mixtures of various flammable powders. Consequently, hazard evaluation leads to a reduction of the disaster damage that arises from dust explosions. Determining the minimum ignition energy (MIE) of flammable mixtures is critical for identifying possibility of accidental hazard in industry. The aim of this work is to measure the critical ignition energy of different kinds of pure dusts with various particle sizes as well as mixtures thereof.The results show that even the addition of a modest amount of a highly flammable powder to a less combustible powder has a significant impact on the MIE. The MIE varies considerably when the fraction of the highly flammable powder exceeds 20%. For dust mixtures consisting of combustible dusts, the relationship between the ignition energy of the mixture and the minimum ignition energy of the components follows the so-called harmonic model based upon the volume fraction of the pure dusts in the mixture. This correlation provides results which show satisfactory agreement with the experimental values.     

A numerical model to simulate smouldering fires in bulk materials and dust deposits

A numerical model is presented which consists of a set of partial differential equations for the transport of heat and mass fractions of eight chemical species to describe the onset of self-ignition and the propagation of smouldering fires in deposits of bulk materials or dust accumulations. The chemical reaction sub-model includes solid fuel decomposition and the combustion of char, carbon monoxide and hydrogen.The model has been validated against lab-scale self-ignition and smouldering propagation experiments and then applied to predictions of fire scenarios in a lignite coal silo. Predicted reaction temperatures of 550 K and propagation velocities of the smouldering front of about 6 mm/h are in good agreement with experimental values derived from lab-scale experiments.     

EVA树脂粉尘/甲烷/空气杂混物爆炸特性

在20 L爆炸实验装置中,开展了3种不同中值粒径的EVA树脂粉尘/甲烷/空气所组成的杂混物爆炸特性研究,探究了甲烷浓度对粉尘爆炸下限、最大爆炸压力的影响。结果表明,尽管添加的甲烷气体浓度低于爆炸下限,仍使得粉尘爆炸下限得以降低,粒径较大的EVA III粉尘,当甲烷体积分数为1%时,爆炸下限降低约25%;粒径较小的EVA I粉尘,当混入甲烷体积分数为4%时,爆炸下限则降低80%;甲烷体积分数每增加1%,可燃粉尘最大爆炸压力上升约10%,但对于粒径较小的EVA I粉尘,当甲烷体积分数为4%时,最大爆炸压力的上升呈现突变趋势,上升近50%。     

Effects of particle characteristics on flame propagation behavior during organic dust explosions in a half-closed chamber

To reveal the effects of particle characteristics on the mechanisms of flame propagation during organic dust explosions clearly, three long chain monobasic alcohols which are solids at room temperature and have similar physical–chemical properties were chosen to carry out experiments in a half-closed small chamber. A high-speed video camera was used to record the flame propagation process and to obtain the direct light emission photographs. Flame temperature was detected by a fine thermocouple. Based on the experimental results above, analysis was conducted on flame propagation characteristics and temperature profiles of organic particle cloud. As a result, it was found that the particle materials, especially volatility, strongly affected the flame propagation behavior. Particle concentration also affects the combustion zone propagation process significantly. With increasing the particle concentration, the maximum temperature of the combustion zone increases at the lower concentration, reaches a maximum value, and then decreases at the higher concentration. The propagation velocity of the combustion zone has a linear relationship with the maximum temperature, which implies conductive heat transfer is dominant in the flame propagation process of the three different volatile dusts.     

Parametric study of the explosivity of graphite-metals mixtures

The explosivity of dust clouds is greatly influenced by several parameters which depend on the operating conditions, such as the initial turbulence, temperature or ignition energy, but obviously also on the materials composition. In the peculiar case of a mixture of two combustible powders, the physical and chemical properties of both dusts have an impact on the cloud flammability and on its explosivity. Nevertheless, no satisfactory ‘mixing laws’ predicting the mixture behavior are currently available and the composition variable to be considered for such models greatly depend on the safety parameters which have to be determined: from volume ratios for some thermal exchanges and ignition phenomena, to surface proportions for some heterogeneous reactions and molar contents for chemical reactions. This study is mainly focused on graphite/magnesium mixtures as they are encountered during the decommissioning activities of UNGG reactors (Natural Uranium Graphite Gas). Due to the different nature and reactivity of both powders, these mixtures offer a wide range of interests. Firstly, the rate-limiting steps for the combustion of graphite are distinct from those of metals (oxygen diffusion or metal vaporization). Secondly, the flame can be thickened by the presence of radiation during metal combustion, whereas this phenomenon is negligible for pure graphite. Finally, the turbulence of the initial dust cloud is modified by the addition of a second powder. In order to assess the explosivity of graphite/magnesium clouds, a parametric study of the effects of storage humidity, particle size distribution, ignition energy, and initial turbulence has been carried out. In particular, it was clearly demonstrated that the turbulence significantly influences the explosion severity by speeding up the rate of heat release on the one hand and the oxygen diffusion through the boundary layer surrounding particles on the other hand. Moreover, it modifies the mean particle size and the spatial dust distribution in the test vessel, impacting the uniformity of the dust cloud. Thus, the present work demonstrates that the procedures developed for standard tests are not sufficient to assess the dust explosivity in industrial conditions and that an extensive parametric study is relevant to figure out the explosive behavior of solid/solid mixtures subjected to variations of operating conditions.     

Niacin,lycopodium and polyethylene powder explosibility in 20-L and 1-m3 test chambers

An experimental program has been undertaken to investigate the explosibility of selected organic dusts. The work is part of a larger research project aimed at examination of a category of combustible dusts known as marginally explosible. These are materials that appear to explode in laboratory-scale test chambers, but which may not produce appreciable overpressures and rates of pressure rise in intermediate-scale chambers. Recent work by other researchers has also demonstrated that for some materials, the reverse occurs – i.e., values of explosion parameters are higher in a 1-m³ chamber than one with a volume of 20 L. Uncertainties can therefore arise in the design of dust explosion risk reduction measures.The following materials were tested in the current work: niacin, lycopodium and polyethylene, all of which are well-known to be combustible and which cover a relatively wide range of explosion consequence severity. The concept of marginal explosibility was incorporated by testing both fine and coarse fractions of polyethylene. Experiments were conducted at Dalhousie University using the following equipment: (i) Siwek 20-L explosion chamber for determination of maximum explosion pressure (P_max), volume-normalized maximum rate of pressure rise (K_St), and minimum explosible concentration (MEC), (ii) MIKE 3 apparatus for determination of minimum ignition energy (MIE), and (iii) BAM oven for determination of minimum ignition temperature (MIT). Testing was also conducted at Fauske & Associates, LLC using a 1-m³ explosion chamber for determination of P_max, K_St and MEC. All equipment were calibrated against reference dusts, and relevant ASTM methodologies were followed in all tests.The explosion data followed known trends in accordance with relevant physical and chemical phenomena. For example, P_max and K_St values for the fine sample of polyethylene were higher than those for the coarse sample because of the decrease in particle size. MEC values for all samples were comparable in both the 20-L and 1-m³ chambers. P_max and K_St values compared favorably in the different size vessels except for the coarse polyethylene sample. In this case, K_St determined in a volume of 1 m³ was significantly higher than the value from 20-L testing. The fact that the 20-L K_St was low (23 bar m/s) does not indicate marginal explosibility of the coarse polyethylene. This sample is clearly explosible as evidenced by the measured values of MEC, MIE, MIT, and 1-m³ K_St (at both 550 and 600 ms ignition delay times).     

Differences and similarities of gas and dust explosions: A critical evaluation of the European ‘ATEX’ directives in relation to dusts

Explosive gas mixtures and explosive dust clouds, once existing, exhibit similar ignition and combustion features. However, there are two basic differences between dusts and gases which are of substantially greater significance in design of safety standards than these similarities. Firstly, the physics of generation and up-keeping of dust clouds and premixed gas/vapour clouds are substantially different. This means that in most situations where accidental explosive gas clouds may be produced quite readily, generation of explosive dust clouds would be highly unlikely. Secondly, contrary to premixed gas flame propagation, the propagation of flames in dust/air mixtures is not limited only to the flammable dust concentration range of dynamic clouds. The state of stagnant layers/deposits offers an additional discrete possibility of flame propagation.

The two European Directives 94/9/EC (1994) and 1999/92/EC (1999) primarily address gases/vapours, whereas the particular properties of dusts are not addressed adequately. Some recent IEC and European dust standards resulting from this deficiency are discussed, and the need for revising the two directives accordingly is emphasized.     

Experiment-based investigations of magnesium dust explosion characteristics

An experimental investigation was carried out on magnesium dust explosions. Tests of explosion severity, flammability limit and solid inerting were conducted thanks to the Siwek 20 L vessel and influences of dust concentration, particle size, ignition energy, initial pressure and added inertant were taken into account. That magnesium dust is more of an explosion hazard than coal dust is confirmed and quantified by contrastive investigation. The Chinese procedure GB/T 16425 is overly conservative for LEL determination while EN 14034-3 yields realistic LEL data. It is also suggested that 2000-5000 J is the most appropriate ignition energy to use in the LEL determination of magnesium dusts, using the 20 L vessel. It is essential to point out that the overdriving phenomenon usually occurs for carbonaceous and less volatile metal materials is not notable for magnesium dusts. Trends of faster burning velocity and more efficient and adiabatic flame propagation are associated with fuel-rich dust clouds, smaller particles and hyperbaric conditions. Moreover, Inerting effectiveness of CaCO₃ appears to be higher than KCl values on thermodynamics, whereas KCl represents higher effectiveness upon kinetics. Finer inertant shows better inerting effectiveness.     

On the explosion and flammability behavior of mixtures of combustible dusts

In the work presented in this paper, the explosion and flammability behavior of combustible dust mixtures was studied. Lycopodium, Nicotinic acid and Ascorbic acid were used as sample dusts.In the case of mixtures of two dusts, the minimum explosive concentration is reproduced well by a Le Chatelier's rule-like formula, whereas the minimum ignition energy is a linear combination of the ignition energies of the pure dusts.An unexpected behavior has been found in relation to the explosion behavior and the reactivity. When mixing Lycopodium and Nicotinic acid or Ascorbic acid, the rate of pressure rise of the mixture is much higher than the rate of pressure rise obtained by linearly averaging the values of the pure dusts (according to their weight proportions), thus suggesting that strong synergistic effects arise; but it is comparable to that of the most reactive dust in the mixture.The observed behavior seems to be linked to the presence of minerals in the Lycopodium particles which catalyze oxidation reactions of Nicotinic acid and Ascorbic acid, as suggested by TG analysis.In the case of mixtures of three dusts, a similar behavior is observed when the concentration of Lycopodium is twice that of the other two dusts.     

Determination of turbulent burning velocities of dust air mixtures with the open tube method

Correlating turbulent burning velocity to turbulence intensity and basic flame parameters-like laminar burning velocity for dust air mixtures is not only a scientific challenge but also of practical importance for the modelling of dust flame propagation in industrial facilities and choice of adequate safety strategy. The open tube method has been implemented to measure laminar and turbulent burning velocities at laboratory scale for turbulence intensities in the range of a few m/s. Special care has been given to the experimental technique so that a direct access to the desired parameters was possible minimising interpretation difficulties. In particular, the flame is propagating freely, the flame velocity is directly accessible by visualisation and the turbulence intensity is measured at the flame front during flame propagation with special aerodynamic probes. In the present paper, those achievements are briefly recalled. In addition, a complete set of experiments for diametrically opposed dusts, starch and aluminium, has been performed and is presented hereafter. The experimental data, measured for potato dust air mixtures seem to be in accordance with the Bray Gülder model in the range of 1.5 m/s<u′<3.5 m/s. For a further confirmation, the measurement range has been extended to lower levels of turbulence of u′<1.5 m/s. This could be achieved by changing the mode of preparation of the dust air mixture. In former tests, the particles have been injected into the tube from a pressurised dust reservoir; for the lower turbulence range, the particles have been inserted into the tube from above by means of a sieve–riddler system, and the turbulence generated from the pressurised gas reservoir as before. For higher levels of turbulence, aluminium air mixtures have been investigated using the particle injection mode with pressurised dust reservoir. Due to high burning rates much higher flame speeds than for potato dusts of up to 23 m/s have been obtained.     

Explosion of lycopodium-nicotinic acid–methane complex hybrid mixtures

With the terms “complex hybrid mixtures”, we mean mixtures made of two or more combustible dusts mixed with flammable gas or vapors in air (or another comburent).In this work, the flammability and explosion behavior of selected complex hybrid mixtures was studied. In particular, we investigated mixtures of nicotinic acid, lycopodium and methane. We performed explosion tests in the 20-L explosion vessel at different overall (nicotinic plus lycopodium) dust concentrations, nicotinic acid/lycopodium ratios, and methane concentrations.An exceptional behavior (in terms of unexpected values of rate of pressure rise and pressure) was found for the complex hybrid mixtures containing lycopodium and nicotinic acid in equal amounts. This mixture was found to be much more reactive than all the other dust mixtures, whatever the dust concentration and the methane content.     

Smoldering combustion of dust layer on hot surface

The critical temperature as well as the critical flux for ignition of a dust layer of cornflour and a mixture of wheatflour and cornflour (80% wheatflour+20% cornflour) on a hot plate have been determined. The moulded sample was cylindrical in shape and of different heights and diameters. The particle size of dusts ranged between 63 μm to 150 μm. The temperature–time histories for self-heating without ignition and with ignition are offered, showing the critical boundaries between them. Also the times to ignition for each dust, showing the effect of sample size on their values, are determined. Certain experimental correlations which relate to times to ignition, as well as the critical temperature for ignition and thermal and geometrical dimensions of sample are presented.