基于热风险理论对道化学评价中物质系数的研究

随着本质安全研究的深入,道化学评价方法中物质系数MF的计算已不能准确描述反应物本身的热风险大小。在道化学评价方法中引入热风险概念,比较热危险性评价方法和道化学评价方法间相异点;以六甲基磷酰三胺工艺为研究对象,用DSC量热仪对反应物进行分析得出放热速率q、反应波峰峰值、单位质量的反应焓Hr,对采集的工艺参数用热力学理论外推法、基因贡献法得出活化能E、比热容CP并以此求出最大反应失效时间TMRad、绝热温升Qad、物质系数MF值以及工艺单元中物料量。得出最大反应失效时间与物质系数MF间具有相关性,道化学评价方法对因失效反应引发二次反应的热风险评估也适用。     

苯和甲苯硝化及磺化反应热危险性分级研究

首先介绍了化工工艺热安全性的内涵,并从反应过程热危险性分析的方法学出发,介绍间隙、半间歇化学反应工艺热危险性分级研究的总体思路及方法。然后,围绕甲苯和苯的硝化、磺化反应,用全自动反应量热仪(RC1e)和加速度量热仪(ARC)测定其反应过程的绝热温升(△Tad)、目标反应所能达到的最高温度(TM)、分解反应最大速率到达时间(θD)等参数。运用风险评价指数矩阵法(方法1)和基于失控过程温度参数的热危险评估法(方法2)分别对其硝化和磺化反应过程的热危险性进行了分级评估。结果表明,这两种方法具有良好的一致性;给定工艺条件下甲苯和苯的一段硝化反应过程的热危险度等级较低;而磺化反应的热危险较高。尽管这两种方法还有一定的局限性,但对于间歇、半间歇合成工艺的本质安全化设计、工艺热危险性的评估具有重要的参考价值和实用意义。     

Probe into effect of the initiator on the thermal runaway hazards of methyl methacrylate bulk polymerization

The bulk polymerization of methyl methacrylate (MMA) is of great importance in chemical industry, but the polymerization process is highly hazardous, and few reports have focused on the effect of initiators on its thermal hazards. In this work, to thoroughly explore the thermal hazard characteristics, the runaway behavior of MMA bulk polymerization is investigated by a combination of thermodynamics experimental and kinetics theoretical methods. The results indicate that the presence of initiator exhibits an undesirable thermal hazard to the MMA bulk polymerization, and its exothermic behavior is also greatly influenced by the type and concentration of initiator. For azobisisoheptanenitrile (ABVN), azodiisobutyronitrile (AIBN) and dibenzoyl peroxide (BPO) initiators as examples, the AIBN-initiated reaction has the shortest adiabatic induction period (39.51 min), whereas the BPO-initiated polymerization exhibits the strongest maximum temperature-rising rate and maximum pressure-rising rate. Under adiabatic runaway, the temperature and pressure change significantly with increasing AIBN concentration, revealing a great potential risk of thermal runaway. Kinetic parameters are calculated to further understand the thermal runaway mechanisms, showing a strong agreement with the adiabatic experimental data. Finally, based on the cooling failure scenario, severity grading is determined by the evaluation criteria. The current work provides extensive data as a reference and guidance for the process design and optimization of MMA bulk polymerization from the perspective of safety.     

Thermal hazard assessment for synthesis of 3-methylpyridine-N-oxide

The exothermic oxidation of 3-methylpyridine with hydrogen peroxide was analyzed by Reaction Calorimeter (RC1e) in semi-batch operation. Heat releasing rate and heat conversion were studied at different operating conditions, such as reaction temperature, feeding rate, the amount of catalyst and so on. The thermal hazard assessment of the oxidation was derived from the calorimetric data, such as adiabatic temperature rise (ΔT_ad) and the maximum temperature of synthesis reaction (MTSR) in out of control conditions. Along with thermal decomposition of the product, the possibility of secondary decomposition under runaway conditions was analyzed by time to maximum rate (TMR_ad). Also, risk matrix was used to assess the risk of the reaction. Results indicated that with the increase of the reaction temperature, the reaction heat release rate increased, while reaction time and exotherm decreased. With the increase of feeding time, heat releasing rate decreased, but reaction time and exotherm increased. With the amount of the catalyst increased, heat releasing rate increased, reaction time decreased and exothermic heat increased. The risk matrix showed that when the reaction temperature was 70 °C, feeding time was 1 h, and the amount of catalyst was 10 g and 15 g, respectively, the reaction risk was high and must be reduced.     

BIPB的热分解动力学和失控反应模拟

为了评估双(叔丁过氧基)二异丙苯(BIPB)的热危害,对其热分解过程进行多速率的动态扫描C80热分析,用几种简单的热危害评估方法分析其热危害。然后应用模式法、无模式法(Friedman微分等转化率法)分别对试验结果进行处理,得到分解动力学数据,并用ASTM E 698法得到活化能数据,同时用C80、ARC和DSC的试验数据验证分解动力学数据的可靠性。最后利用无模式法的分解动力学数据进行BIPB绝热条件下和非绝热的2m3球形容器中的失控反应模拟,得到类似工艺条件下BIPB的安全控制温度。     

自反应性化学物质热危险性综合评估

自反应性化学物质热危险性评估的关键在于表征参数的选择和量化,单一的评估参数往往仅表征其热危险性的某一方面。综合考虑自反应性物质发生热分解反应的难易程度及其造成后果的严重程度两个方面,分别选取放热反应初始温度(To)和反应热(-ΔH)作为相应的表征参数,通过半正态分布函数对这两个指标进行标准化处理。在此基础上根据风险的定义提出了一种新的自反应性化学物质的热危险性综合评估指数(THI指数),并建立相应的热危险性分级标准,对自反应性化学物质的热危险性进行综合评估与分级。结果表明,建立的THI指数所确定的热危险性分级结果与基于活化能和最大绝热温度的RHI指数的反应危险性等级基本一致,该指数能够对自反应性化学物质的热危险性进行定量评估。     

Case study: T2 Laboratories explosion

A tragic explosion resulting from a runaway chemical reaction occurred at the T2 Laboratories, Inc. facility in December 2007. The U.S. Chemical Safety Board (CSB) completed an incident investigation of the T2 explosion, identifying the root cause as a failure to recognize the runaway reaction hazard associated with the chemical it was producing. Understanding the consequences of process upset conditions is critical to determine risk. This paper will focus on lessons learned from this incident including a comprehensive hazard assessment for reactive chemicals as well as proper collection and application of adiabatic calorimetry data to characterize the chemical reaction and determine appropriate mitigation strategies. Examples will be provided to establish safer operating conditions, implement safeguards and reduce the overall risk.     

低压环境对锂电池热失控释放温度影响

为研究锂电池在民航飞行低压特殊环境的安全性及发生热失控灾害后的高温危险性,通过可模拟飞行变动条件的动压变温实验舱开展系列实验,研究锂电池在不同低压环境下的（101,60,30 kPa）多节18650型锂离子电池热失控温度特性,采集电池池体温度及热失控喷射释放温度等参数。研究结果表明:随环境压力降低,圆柱锂电池间的热失控传播并不能被阻断,但锂电池热失控灾害所释放产生的高温区域减少,且高温持续时间变短,释放所产生温度的高温危险性随环境压力的降低而有所降低。     

Modeling thermal analysis for predicting thermal hazards relevant to transportation safety and runaway reaction for 2,2′-azobis(isobutyronitrile)

The pure decomposition behavior of 2,2′-azobis (isobutyronitrile) (AIBN) and its physical phase transformation were examined and discussed. The thermal decomposition of this self-reactive azo compound was explored using differential scanning calorimetry (DSC) to elucidate the stages in the progress of this chemical reaction. DSC was used to predict the kinetic and process safety parameters, such as self-accelerating decomposition temperature (SADT), time to maximum reaction rate under adiabatic conditions (TMR_ad), and apparent activation energy (E_a), under isothermal and adiabatic conditions with thermal analysis models. Moreover, vent sizing package 2 (VSP2) was applied to examine the runaway reaction combined with simulation and experiments for thermal hazard assessment of AIBN. A thorough understanding of this reaction process can identify AIBN as a hazardous and vulnerable chemical during upset situations. The sublimation and melting of AIBN near its apparent onset decomposition temperature contributed to the initial steps of the reaction and explained the exothermic attributes of the peaks observed in the calorimetric investigation.     

Using thermal analysis with kinetic calculation method to assess the thermal stability of azo compound on construction materials

The application of construction polymers in engineering and alternative materials has always occupied a place in the market. In the production process of polymer resins, initiators can be used to lower the polymerization reaction energy threshold, which can improve reaction efficiency and reduce energy loss. However, as a commonly used energetic substance in the polymerization process, azos have caused related process hazards due to their exothermic characteristics. Because of this, it is essential to examine and analyze the thermal hazard characteristics of emerging azo substances, such as 2-cyanopropan-2-imemicarbazide (CABN). Although previous literature performs the calculation on related thermal hazard parameters of CABN, there is still exists a void for discussion in estimating the reaction model to avoid analogous hazards and enhance the existing thermal analysis. Based on the past literature, the reaction model is improved with thermogravimetric analysis as evidence. The revised thermal hazard parameters are calculated as the basis of control and mitigation measures, the kinetic model is used to estimate the modified safety parameters, and in the judgment of the runaway reaction, the critical temperature of the runaway is found by analyzing the influence of slight changes in ambient temperature on the reaction temperature. The results show that the critical temperature that causes CABN to enter the runaway reaction is delayed, and the hazard is lower than in the storage situation. Therefore, the thermal hazard to CABN mainly focuses on the safety environment and measures during storage.     

交联剂TAIC反应风险评估分析

利用全自动反应量热仪和绝热加速量热仪等相关实验仪器检测出TAIC(三烯丙基异氰尿酸酯)合成反应的反应热、比热容及热稳定性等数据,依据绝热温升、工艺温度、技术最高温度、最大反应速率到达时间及失控体系可能达到的最高温度这5个温度参数按照评估标准从分解热、严重度、可能性、矩阵、工艺危险度这5个方面分别进行评估。通过对热参数及实验过程进行分析提出降低工艺危险等级的工艺优化方法。根据最终评估结果对TAIC生产装置的安全性进行评价,提出相应的整改措施及建议。     

Thermal hazards analysis of styrene in contact with impurities

Styrene is a reactive monomer commonly used to produce polystyrene and other copolymers. Unintended thermal runaway polymerization reactions of styrene keep reoccurring and have led to catastrophic consequences. One of the possible causes of these runaway incidents involves the contamination of the styrene monomer by incompatible species, which was not adequately investigated and documented. This study focuses on the quantification of thermal runaway hazards of styrene in contact with a series of contamination substances by adopting calorimetric analysis. Both Differential Scanning Calorimeter (DSC) and Advanced Reactive System Screening Tool (ARSST) were employed to examine the exothermic characteristics of styrene mixed with contaminating substances at different concentration levels and mixing conditions. Key safety parameters of the exothermic reaction, such as the onset temperature, the overall heat release, the maximum self-heating rate, as well as the activation energy, were obtained. The results indicated that the thermal runaway polymerization of purified styrene was significantly altered by the presence of contaminant species. Water effectively retarded and quenched the runaway polymerization at a higher temperature range. Alkaline had no substantial effect on the thermal runaway characteristics. The presence of acid solution under both static contact and vigorous mixing condition significantly promoted the thermal polymerization of styrene. A trace amount of concentrated acid initiated violent exothermic activity even at room temperature; and the severity of the reaction was profoundly impacted by the mass-transfer. Our study demonstrates significant implications in the prevention of runaway incidents during transportation and storage of styrene.     

Hazard evaluation for chlorination and amination reactions of fluorocytosine production process

Reaction thermal runaway is one of the most important reasons leading to chemical accidents. With the rapid development of the chemical industry in the world, especially the fine chemical industry, various safety accidents also occur frequently. Therefore, it is necessary to study the exothermic behavior of the reaction process. In this study, reaction calorimeter was used to study the exothermic phenomena during the chlorination reaction and amination reaction. Differential scanning calorimetry was performed on the reactants, and thermogravimetric experiments were performed on the products. In addition, adiabatic experiment was performed to study the thermal runaway behavior of amination products under adiabatic conditions. The results showed that the target reactions generated a large amount of heat in the initial stage. The maximum temperature of amination reaction is higher than the initial decomposition temperature of the amination product under adiabatic condition. The pyrolysis of amination product was divided into three stages. The product had a high apparent activation energy at the beginning of decomposition, and the apparent activation energy decreased as the decomposition progressed.     

Thermal risk analysis of cumene hydroperoxide in the presence of alkaline catalysts

Many studies have been performed to clarify the basic thermal runaway hazards and kinetics of cumene hydroperoxide (CHP) decomposition. However, materials that are incompatible with CHP have not been clearly identified. Alkaline solutions have been used as a catalyst to form dimethylphenyl carbinol (DMPC) and dicumyl peroxide (DCPO); however, these solutions also affect the reaction and storage temperature of CHP. In this study, thermal calorimeters, differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2), were used to compare the effects of various bases on the decomposition of CHP in cumene. Specifically, the exothermic onset temperature, change in pressure over time, self-heating rate and heat of decomposition were evaluated. Moreover, to appraise the degree of hazard associated with the use of CHP, the compatibility of CHP with various substances was analyzed, and a risk matrix for thermal runaway reactions was obtained. The results of the present study could be used to design safety procedures for the production of CHP and its derivatives.     

Preparation of n-Octadecane@MF resin microPCMs and its application in temperature control of esterification reactions

Reaction thermal runaway accidents occur frequently and occupy a high proportion in chemical accidents. Reducing accidents by controlling reaction temperature is of great implication to enhance the safety level of chemical processes. Phase change materials (PCMs) have a good energy storage potential, which can rapidly convert the reaction exotherm in the reaction process into its own phase change latent heat, urgently control the reaction temperature, and enhance the process thermal safety level. In this study, using n-octadecane as the core and melamine-formaldehyde (MF) resin as the shell, microencapsulated phase change materials (microPCMs) was made, which has a smooth spherical shape, good thermal stability, and a phase change enthalpy up to 162.87 J/g. The homogeneous esterification reaction of 2-butanol (2 B) and propionic anhydride (PA) was selected as the target reaction, and then the reaction was scaled up equivalently to investigate the effect of amplification to the reaction system. The results indicated that the temperature control of the esterification reaction system by microPCMs is the synergy between physical inhibition and chemical inhibition. The reaction temperature could be controlled by adding microPCMs, and the temperature control effect improved with the increase of microPCMs addition. In large scale reactors, microPCMs still has certain temperature control ability after being added.     

Planning protection measures against runaway reactions using criticality classes

A systematic approach to the assessment of thermal risks linked with the performance of exothermal reactions at industrial scale was proposed a long time ago. The approach consisted of a runaway scenario starting from a cooling failure and a classification of these scenarios into criticality classes. In the mean time these tools became quite popular and many chemical companies use them. Recently, the international standard IEC 61511 required the use of protection systems with reliability depending on the risk level. Since the criticality classes were developed as a tool for the choice of risk reducing measures as a function of the criticality, it seems obvious that the criticality classes may be used in the context of the standard IEC 61511, which provides a relation between the risk level and the reliability of protection systems.Firstly, the runaway scenario and the criticality classes will be shortly described. Secondly, the assessment criteria for severity and probability of occurrence of a runaway scenario will be described together with the required data and their interpretation in terms of risk. Thirdly, the assessment procedure is exemplified for the different criticality classes. Finally, the design of protection measures against runaway and the required IPL and SIL are based on the risk assessment obtained from the criticality classes. This approach allows minimising the required data set for the safety assessment and for the definition of the protection system designed in order to avoid the development of the runaway.     

低压环境下不同三元圆柱锂电池热失控危险特性对比研究

为研究21700和18650新旧2型多用途锂离子电池在航空运输低压环境下的热失控特性差异，采用动压变温实验舱搭建实验平台开展实验。将实验环境压力设定为飞机巡航时的环境压力30 kPa，对比常压101 kPa，使用外部热源加热的方式触发锂电池热失控，利用热传播引发相邻电池热失控，分别从热失控温度变化特性、热释放速率和热解气体组分浓度变化进行分析。研究结果表明:能量密度更高的21700电池热失控峰值温度更高，高温危险性要高于18650电池，但触发热失控所需的热量更多，电池间热传播时间会延长；低压环境有利于降低锂电池热失控燃爆峰值温度，减小燃爆热释放速率，但会产生更多CxHy和CO等具有燃爆性的热解气体，可能会在有限空间内与氧气混合引起二次燃爆。     

Investigation of the decomposition reaction and dust explosion characteristics of crystalline dicumyl peroxide

The dicumyl peroxide (DCP) is widely used as a polymerization initiator, catalyst and vulcanizing agent in the chemical industry. A number of accidents have been caused by its thermal instability in storage or manufacturing process. Thus, its hazard characteristics have to be clearly identified. First of all, the differential scanning calorimeter (DSC) is used to measure the heat of decomposition reaction, which can contribute to understanding the reaction characteristics of DCP. The accelerating rate calorimeter (ARC) is used to measure the rates of temperature and pressure rises of decomposition reaction, and then the kinetics parameters are estimated. Furthermore, the MIKE 3 apparatus and the 20-l-Apparatus are used to measure and analyze the dust explosion characteristics of DCP at room temperature and atmospheric pressure. Finally, Semenov's thermal explosion theory is applied to investigate the critical runaway condition and the stability criterion of decomposition reaction, and to build the relationship of critical temperature, convective heat transfer coefficient, heat transfer surface area and ambient temperature. These results contribute to improving the safety in the reaction, transportation and storage processes of DCP.     

The critical runaway condition and stability criterion in the phenol–formaldehyde reaction

The procedure of phenol–formaldehyde polymerization is a rather important and complicated reaction in the chemical industry. This exothermic polymeric reaction releases a huge amount of heat. The high amount of energy accumulated and increasing temperature in this reaction process always lead to runaway reaction and a hazard situation owing to the high released heat and improper operation. In this investigation, we used sodium hydroxide as alkali–catalyst in the phenol–formaldehyde polymerization and estimated the reaction kinetics parameters to evaluate the thermal hazard conditions. The critical temperatures and stable criteria of the runaway reaction in this exothermic polymerization were evaluated. This technique is important and useful for safe operation in the phenol–formaldehyde polymerization process.