软/硬质悬浮填料对MBR中EPS的影响

以聚丙烯无纺布为膜组件,向浸渍式膜生物反应器(MBR)中分别投加硬/软质悬浮填料处理人工废水.分析测定EPS、SVI、膜污染阻力及跨膜压力的变化,采用统计分析方法研究了软/硬质悬浮填料对MBR中EPS及SVI的影响;通过扫描电镜(SEM)分析,表征添加软/硬质悬浮填料膜表面的污染状况.结果表明,添加软/硬质悬浮填料膜组件表面滤饼中的溶解性EPSS和结合性EPSB与膜污染阻力的皮尔逊相关系数(rp)分别为0.929～ 0.984和0.798～0.853,EPSS与膜污染阻力之间表现出更强的相关性,EPSS对膜污染阻力的贡献大于EPSB.添加软/硬质悬浮填料MBR污泥混合液的EPS与SVI的皮尔逊系数(rp)分别为0.895和0.798,呈现明显的正相关性.SEM分析也表明,添加软质填料的膜表面污泥覆盖程度大于硬质填料的膜表面,但膜内部的污泥沉积量明显低于硬质填料.与软质悬浮填料相比,硬质悬浮填料能导致MBR污泥混合液的SVI和EPS含量增大,增加膜污染速率和不可逆膜污染阻力,软质悬浮填料具有更好的控制膜不可逆污染的效能.     

A preliminary explore to the forced ventilation on the toxic gas release/dispersion and the hazard mitigation within a petrochemical plant

More than thirty-five years ago, the Bhopal disaster shook the whole world and investigators found out that many people survived just because they turned on the fans in their bedrooms. It was postulated that the forced ventilation played an important role in diluting the toxic gas and saved these people. In order to provide evidence to solve this old mystery, this research employed FLACS software to assess the hazardous degree of a toxic gas (hydrogen sulfide) leakage within a petrochemical process. Series of gas dispersion simulations were performed to actualize the hazardous characteristics and the corresponding risks of the release accident. The study shows that the hazardous level and the hazard range can be greatly influenced when parameters, such as the gas leakage circumstances (atmospheric conditions and wind speed) and the mitigation measures (direction of fans and their speed) are altered.By using explosion-proof fans in different positions and ventilation directions, combined with the natural wind in a certain direction, this research attempts to detect the best combination from various mitigation designs and to compare the influence of fan directions on hazard mitigation. It is also the first time of its kind to simulate the effect of forced ventilation on hazard mitigation within a process plant. The results show that the hazardous level of a toxic release can be effectively alleviated, when the direction of the mechanical ventilation is against the natural wind direction. With the help of the CFD simulation and the quantitative risk analysis technique, different loss prevention strategies can be tested via this method in order to establish a safer working environment.     

Effects of thickness profile and inner/outer of localized thin area defects on the remaining strength of pressure equipment

When encountering pressure equipment with a structural defect such as a local thinning defect (LTA), a critical question often arises regarding the safety of continued operation. This is primarily determined by the strength at the LTA zone, as it represents the weakest point of the structure. The remaining strength factor (RSF) is proposed as an indicator to evaluate the remaining strength and life of pressure equipment when a severe LTA is identified. The API 579/ASME FFS standard offers a series of practical engineering approaches for field engineers to follow, which have achieved great success. However, it has been found that the simpler Level 1 and Level 2 approaches sometimes fail to differentiate between LTAs on the inner or outer surface of the pressure equipment, yielding identical numerical processes and results. Moreover, the use of critical thickness profiles to replace the actual thickness profile in analysis can lead to overly optimistic estimation of the RSF, posing a potential danger when the RSF is close to the allowable limit. Key issues investigated in this study include: (a) discrepancies caused by the use of simplified critical thickness profiles or parabolic profiles, as API 579 suggested, on the RSF; (b) differences in RSFs when the same LTA is on the inner and outer wall; and (c) comparisons of membrane stress and bending stress, as well as their influences on the RSF at the cross-section of the vessel wall. It can be concluded with certainty that all simplified geometries (CTP and PTP) tend to underestimate the RSF and should be used with caution. Additionally, the actual remaining strength of the outer LTA was found to be slightly lower than that of the inner LTA of identical size. Therefore, when remaining life and derating for prolonged operation are of interest, finite element analysis on pressure equipment with the LTA is recommended.     

基于遗传算法的支持向量机预测有机物自燃点的研究

根据定量构效关系(QSPR)原理,研究自燃点(AIT)与其分子结构间的内在定量关系。以265种有机化合物作为样本集,随机选择238种作为训练集,27种作为测试集,用遗传算法(GA)进行变量选择,分别建立多元线性回归(MLR)模型和支持向量机(SVM)模型研究有机物的自燃点与其分子结构间的关系。通过分析,发现造成模型预测效果不佳的原因是试验数据本身存在问题。通过对2个模型的比较,结果为GA-SVM模型明显优于GA-MLR模型,说明自燃点与其分子结构间具有很强的非线性关系。     

TMBR+NF/RO组合工艺处理垃圾渗滤液的工程应用

采用TMBR+NF/RO组合工艺对湖北省宜昌市某垃圾卫生填埋场渗滤液进行处理,介绍了组合工艺的流程、特点、设备规格、技术参数。TMBR系统对可生化降解COD处理后,COD平均质量浓度为822 mg/L,平均去除率为95.8%,对NH_3-N平均去除率为94.9%;经过NF/RO出水的COD平均值为45 mg/L,NH_3-N均小于25mg/L,达到《生活垃圾填埋场污染控制标准》(GB 16889—2008)的排放标准。组合工艺处理成本为29.5元/m3。     

航空人为差错事故/事件分析(ECAR)模型研究

为深入研究航空人为差错事故/事件的影响因素,以人为差错相关理论为基础,对比分析几种典型的人为差错分析模型;通过借鉴ECCAIRS分析框架,并在基元事件分析(EEAM)逻辑和CCAR396部的分类方法基础上,构建航空人为差错事故/事件分析(ECAR)模型,它从事件层、描述层、原因层和组织因素与改进建议层,分析航空事故和不安全事件的人为差错。此外,还将组织因素概念引入该模型。     

GP/APP膨胀阻燃体系对硅橡胶复合材料阻燃及抑烟性能的影响

为了探究石墨粉 (GP) 与聚磷酸铵 (APP) 膨胀阻燃体系对硅橡胶复合材料的阻燃及抑烟特性的影响，采用锥形量热仪 (CCT)、热重分析仪 (TG) 及极限氧指数测试仪 (LOI) 对阻燃硅橡胶复合材料进行表征。研究结果表明:与单独添加膨胀阻燃剂APP的阻燃硅橡胶相比，添加GP/APP膨胀阻燃体系可有效提升燃烧过程中形成的膨胀碳层的致密度，降低阻燃硅橡胶复合材料的热释放速率及总烟释放量，提高阻燃硅橡胶复合材料高温阶段的热稳定性，提升阻燃硅橡胶复合材料的燃烧成炭率和质量保持率； 使阻燃硅橡胶复合材料的氧指数值增大。     

Effect of initial pressure on the lower explosion limit of nicotinic acid/acetone mixture

In the work presented in this paper, the effect of initial pressure on the lower explosion limit (LEL) of the hybrid nicotinic acid/acetone mixture was investigated through standard explosion tests carried out in the 20 L sphere. From experimental results, the flammability diagram was built in the plane (concentration/minimum explosive concentration) of nicotinic acid versus (concentration/LEL) of acetone. Interestingly, it has been found that, in going from low pressures (P < 1 atm) to high pressures (P > 1 atm), the extension of the flammability region increases. This behavior has been attributed to the fact that the turbulence kinetic energy (and thus the energy dissipation) decreases with increasing initial pressure. Bartknecht's correlation for LEL of hybrid mixtures was modified to take into account the effect of pressure, and two correlations were obtained able to give satisfactory predictions of experimental data at both low pressures and high pressures.     

引气剂和聚丙烯纤维对高水材料性质的影响研究

为了改变高水材料的破坏特点,采用引气剂和聚丙烯纤维双掺对其进行改性。试验结果表明:随着引气剂掺量的增加,浆体的流动性逐渐降低,混合浆液失流时间延长,试块密度和单轴抗压强度逐渐减小;聚丙烯纤维的掺入,对浆体流动性、失流时间、引气率影响均较小。聚丙烯纤维最佳掺量为2 kg/m3,引气剂和聚丙烯纤维的掺入使硬化体的弹性模量略有减小,且使试块由脆性破坏转变为延性破坏,在保持整体不散的情况下,提高其压缩量。SEM观察表明:钙矾石在气泡壁上集中生成,聚丙烯纤维与基体的界面处有利于针状钙矾石的生成,从而使聚丙烯纤维更好地发挥增强增韧的作用。     

A comparative study on the autoxidation of dimethyl ether (DME) comparison with diethyl ether (DEE) and diisopropyl ether (DIPE)

The Japanese government is planning to introduce DME as a substituted energy for oil and LNG. Introduction of DME could contribute greatly to both the prevention of global warming and the formation of resource-recycling societies. In these circumstances, a safety assessment of DME is very important when DME is used on a large scale. There is a possibility that prolonged exposure in air induces autoxidation to produce explosive organic peroxides during transportation and storage of DME. Therefore, the reactivity of DME with oxygen and the mechanism of the autoxidation were investigated. Accelerating Rate Calorimetry (ARC) was used to evaluate the thermal stability of DME and DIPE, a known peroxide producers, under adiabatic and various atmospheric conditions. In ARC studies of DME under oxygen, exothermic decompositions were detected although its self-heating rate was low in comparison with DIPE. Oven storage tests were carried out and iodimetry was used to measure the concentration of peroxides produced from DME in comparison with DIPE and DEE. However, no products could be found for DME either by GC/MS or by iodimetry, while some evidence of autoxidation of both DEE and DIPE were obtained from these experiments.     

条件价值法评估生命价值的应用探讨

分别对条件价值法评估生命价值的经济学理论基础和研究进展进行阐述;分析条件价值法应用于生命价值评估可能会产生的偏差有假想偏差、策略偏差和信息偏差,并探讨支付意愿与受偿意愿、诱导技术、风险变化率对其结果有效性的影响。根据文献分析结果,结合前期应用条件价值法评估生命价值实证研究的成果,就如何提高条件价值法评估生命价值结果的可靠性和有效性给出实证研究设计方案,通过总体设计框架、工作环境风险认知调查、工作风险支付意愿的设计、社会经济信息变量的设置、调查准备与预调查、样本容量及抽样设计、数据统计分析等多个方面的优化设计可以保障评估生命价值的有效性和可靠性。     

铜导线短路熔痕的SEM/EDS分析

在电气线路火灾原因的调查中,为更好地区分铜导线一次短路与二次短路的熔痕特征,用扫描电子显微镜(SEM)和X-射线能谱仪(EDS)对2种熔痕的形貌和相应的元素成分进行了试验研究。结果表明:铜导线一次短路与二次短路熔痕的表观形貌特征和元素成分具有明显的不同,二者的区别主要表现在熔痕表面所含的气孔、元素种类及导线本体与熔痕之间的过渡区方面,一次短路熔痕表面气孔多,元素种类少,导线与熔痕之间有明显界限,二次短路熔痕则相反。该研究结果可以区分短路熔痕形成的环境气氛,以此判断导线短路熔痕类型,为电气线路火灾原因的调查提供科学依据。     

基于贝叶斯网络的尾流事故机理分析

针对事故树分析法的局限性,在尾流事故树的基础上,建立贝叶斯网络(BN)。运用推理运算对BN进行定量分析,得出:空中交通密度太大、空中交通管制(ATC)间隔判断错误和短期冲突告警(STCA)被忽略是事故的关键致因。将针对致因提出的改进措施引入到BN中,评价相关措施的有效性。应用BN进行尾流事故的机理分析,能够以比逻辑门更好的形式表达变量间的不确定性关系,从而更加方便地找到导致事故发生的关键因素。     

煤热动力学参数、特征温度与挥发分关系的试验研究

通过煤的热动力学参数和特征温度可以表征煤自燃危险程度。而在实际情况中,这些数据缺少,往往只有煤的工业参数。因此,研究工业参数与表征煤自燃危险参数的关系十分必要。为了分析和建立该关系,基于非等温试验方法对不同煤样进行热重试验分析,得出8个煤样在10℃/min升温速率下的反应动力学参数与煤工业分析参数的关系,揭示挥发分与煤的氧化特性、特征温度的关系。试验结果表明:8个煤样的挥发分排序F3>F8>F4>F7>F2>F1>F5>F6,各特征温度排序基本满足T3相似文献   

基于ADAMS/Rail的直线电机轨道交通安全性研究

阐述了直线电机轨道交通的技术特点,并就其安全评价体系做了介绍,应用ADAMS/Rail软件分别建立了轮对、构架、悬挂系统、止挡、自导向径向转向架、直线电机以及车体的模型,并考虑轮轨关系组合为直线电机轨道交通的车辆-轨道耦合动力学整体模型,进行了大量的计算仿真。笔者主要以脱轨系数为例进行了动力响应分析,给出考虑了径向转向架和直线电机后的安全评判指标,比较了与径向转向架和未安装直线电机的区别,验证了模型的正确性和有效性。为后续研究直线电机轨道交通车辆-轨道耦合动力学模型提供了理论基础,从而可以进一步从安全性角度研究线路设计参数。为我国今后直线电机轨道交通建设就线路参数对车辆运行安全性的影响研究方面起到理论指导作用。     

基于BERT的灾害三元组信息抽取优化研究

为从网络媒体文本中快速、准确提取灾害三元组信息,利用 自然语言处理(NLP)技术,研究灾害三元组信息抽取应用及其算法优化.通过双向编码器表示(BERT)预训练语言模型,应用于地质灾害三元组信息提取的实例中,针对模型由于底层多头注意力(MHA)机制会导致"低秩瓶颈"问题,对此,通过增大模型key-size对其进行优化.结...     

单板层积梁弯曲破坏的试验研究与分析

在万能力学试验机上测试由高频热压方法制造的桦木和椴木单板层积梁的密度、静曲强度(MOR)、弹性模量(MOE)和水平剪切强度等力学性质;讨论LVL(单板层积材)梁受弯曲、水平剪切载荷时的主要破坏形式并得出相关结论。测试结果表明,在该试验条件下,桦木和椴木LVL梁具有较大的密度、MOR和较高的MOE。其主要物理力学性能受树种的影响较大,桦木LVL梁的主要性能均优于椴木LVL梁。当LVL梁受弯曲破坏时,其主要破坏形式为整体断裂破坏、开裂破坏以及混合破坏等3种;受水平剪切应力破坏时,以基材剪切破坏和胶层剪切破坏两种形式为主。     

湿法脱硫后烟气中SO3/硫酸雾测试方法的试验

在自行设计和搭建的模拟湿法脱硫烟气系统中,研究了基于控制冷凝法原理的SO_3/硫酸雾采集装置对湿法脱硫后SO_3/硫酸雾的捕集性能,重点考察了螺旋管与石英棉冷凝温度、采样枪温度、采样流量、采样时间和SO_3/硫酸雾质量浓度对SO_3/硫酸雾捕集性能的影响。结果表明,在研究范围内,湿法脱硫后SO_3/硫酸雾采集装置优化的操作参数为:螺旋管及石英棉冷凝温度95℃,采样枪温度280℃,采样流量17 L/min,采样时间30 min。SO_3/硫酸雾质量浓度较高时,螺旋冷凝管对SO_3/硫酸雾的捕集起主要作用,其捕集的SO_3/硫酸雾比例在75.8%~80.8%,远高于螺旋冷凝管与石英棉捕集SO_3/硫酸雾的比例;SO_3/硫酸雾质量浓度较低(约1mg/m3)时,采样枪对SO_3/硫酸雾的捕集起主要作用,其捕集SO_3/硫酸雾的比例大于50%。     

局域网内ARP协议攻击及解决办法

地址解析协议(ARP,Address Resolution Protocol)是用于关联某个3层(网络层)地址(如IP地址)和某个两层(数据链路层)地址(MAC地址)。由于ARP协议的自身的缺陷,使得ARP协议在使用的过程中存在着盗用IP地址和ARP欺骗等严重的安全问题。笔者在对ARP协议简要介绍的基础上,主要分析了利用ARP协议漏洞进行网络攻击的原理和攻击的常见方式,并提出相关的ARP攻击的解决办法。