地铁车站火灾中调度列车辅助站台人员疏散方法研究

随着我国城市地铁建设的发展,复杂多层地铁站台形式的出现导致地铁车站火灾发生时底层站台人员疏散所需时间常超出现有规范.提出调度列车疏散站台人员的方式,论证了地铁列车辅助站台人员安全疏散措施的可行性,给出了列车发车间隔、列车运行速度、站间距离等因素对疏散所需时间的影响,结果表明发车间隔是决定列车疏散所需时间的主要因素.研究工作可以为同类地铁站台人员安全疏散设计和应急预案制定提供参考.     

Overall and local movement speeds during fire drill evacuations in buildings up to 31 stories

The time that it takes an occupant population to reach safety when descending a stairwell during building evacuations is typically described by measurable engineering variables such as stairwell geometry, speed, density, and pre-evacuation delay. In turn, engineering models of building evacuation use these variables to predict the performance of egress systems for building design, emergency planning, or event reconstruction. As part of a program to better understand occupant movement and behavior during building emergencies, the Engineering Laboratory at the National Institute of Standards and Technology (NIST) has been collecting stairwell movement data during fire drill evacuations of office buildings. These data collections are intended to provide a better understanding of this principal building egress feature and develop a technical foundation for future codes and standards requirements. To date, NIST has collected fire drill evacuation data in eight office building occupancies ranging from 6 to 62 stories in height that have included a range of stairwell widths and occupant densities.While average movement speeds in the current study of 0.48 m/s ± 0.16 m/s are observed to be quite similar to the range of literature values, local movement speeds as occupants traverse down the stairwell are seen to vary widely within a given stairwell, ranging from 0.056 m/s to 1.7 m/s. These data should provide confirmation of the adequacy of existing literature values typically used for occupant movement speeds or provide updated values for future analyses.     

Fate of trace tetracycline with resistant bacteria and resistance genes in an improved AAO wastewater treatment plant

The fate of trace tetracycline, tetracycline resistant bacteria (TRB) and tetracycline resistant genes (TRGs) in an improved anaerobic-anoxic-oxic (AAO) wastewater treatment plant (WWTP) was investigated in this study. Quantitative real-time polymerase chain reaction (qPCR) and conventional heterotrophic plate count method were used to measure eight tet genes (tetA, tetB, tetC, tetE, tetM, tetO, tetS and tetX) and TRB, respectively. The TRB percent of total heterotrophic bacteria (THB) is about 1.31–24.1% in WWTP influent. Tet gene abundance in the WWTP varied greatly among the gene types. The concentrations of TRGs in effluent samples ranged from 7.11 × 10⁻⁹ to 1.53 × 10⁻⁴ copies/copy 16S rRNA gene. TRB and THB, tetM and tetO, tetE and tetX, but not the others, showed a significant correlation with each other (p < 0.01). The relationships between ribosomal protection protein genes, enzymatic modification gene and corresponding concentrations of antibiotics were found to be considerably significant (R² = 0.898, p < 0.01 for ribosomal protection protein genes and R² = 0.872, p < 0.05 for enzymatic modification gene).     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Determination of the applicable exhaust airflow rate through a ventilation shaft in the case of road tunnel fires

In this study, a model experiment in a long road tunnel employing the longitudinal ventilation system with a ventilation shaft is carried out during a fire accident to determine the optimum exhaust airflow rate through the ventilation shaft. The appropriate operation of the shaft fan according to the position of fire is investigated, and the optimum exhaust airflow rate for prevention of smoke spreading through the tunnel is determined based on the entire exhaust of both smoke and airflow generated by fire and jet fan operation, respectively. As a result of using the amount of smoke, the critical air velocity produced by jet fans, the effective cross-sectional area of a tunnel and the correction factor, a formula for exhaust airflow rate is drived. In addition, a correction factor (α = 1.1) for the thermal expansion caused by heat of a 20 MW fire is determined theoretically and experimentally. It is expected that this study will contribute to plan the shaft operation for the emergency ventilation as well as provide the preliminary data to design the airflow rate of shaft.     

Using a cluster randomized controlled trial to determine the effects of intervention of battery and hardwired smoke alarms in New South Wales,Australia: Home fire safety checks pilot program

IntroductionIn 2014, Fire & Rescue New South Wales piloted the delivery of its home fire safety checks program (HFSC) aimed at engaging and educating targeted top “at risk” groups to prevent and prepare for fire. This pilot study aimed to assess the effectiveness of smoke alarms using a cluster randomized controlled trial.MethodsSurvey questionnaires were distributed to the households that had participated in the HFSC program (intervention group). A separate survey questionnaire was distributed to the control group that was identified with similar characteristics to the intervention group in the same suburb. To adjust for potential clustering effects, generalized estimation equations with a log link were used.ResultsMultivariable analyses revealed that battery and hardwired smoking alarm usage increased by 9% and 3% respectively among the intervention group compared to the control group. Females were more likely to install battery smoke alarms than males. Respondents who possessed a certificate or diploma (AOR = 1.31, 95% CI 1.00–1.70, P = 0.047) and those who were educated up to years 8–12 (AOR = 1.32, 95% CI 1.06–1.64, P = 0.012) were significantly more likely to install battery smoke alarms than those who completed bachelor degrees. Conversely, holders of a certificate or diploma and people who were educated up to years 8–12 were 31% (AOR = 0.69, 95% CI 0.52–0.93, P = 0.014) and 24% (AOR = 0.76, 95% CI 0.60–0.95, P = 0.015) significantly less likely to install a hardwired smoke alarm compared to those who completed bachelor degrees.ConclusionsThis pilot study provided evidence of the benefit of the HFSC in New South Wales. Practical Applications: Fire safety intervention programs, like HFSC, need to be targeted to male adults with lower level of schooling even when they are aware of their risks.     

Magnetophoretic separation of Chlorella sp.: Role of cationic polymer binder

Cationic polyelectrolyte promoted effective attachment of iron oxide nanoparticles (IONPs) onto microalgal cells through electrostatic attraction. Poly(diallyldimethylammonium chloride) (PDDA) and chitosan (ChiL), both are cationic polymer, are feasible to act as binding agent to promote rapid magnetophoretic separation of Chlorella sp. through low gradient magnetic separation (LGMS) with field gradient ▿B less than 80 T/m in real time. Cell separation efficiency up to 98% for the case of PDDA and 99% for the case of ChiL can be achieved in 6 min when 3 × 10⁷ cells/mL Chlorella sp. are exposed to 300 mg/L surface functionalized-IONPs (SF-IONPs). Different polyelectrolytes do not give significant effect on cell separation efficiency as long as the particle attachment occurred. However, the PDDA is more preferable as the binder for all type of microalgae medium than the chitosan (ChiL) since it is not pH dependent. SF-IONPs coated with PDDA guarantee the cell separation performance for all pH range of cell medium, with 98.21 ± 0.40% at pH 8.84. On the other hand, the ChiL performance will be affected by the cell medium pH, with only 22.93 ± 31.03% biomass recovery at pH 9.25.     

Access to trauma centers for road crashes in the United States

Introduction: Existing research indicates that around 90% of all U.S. residents have access to at least one level I or II trauma center within 60 min. However, a limitation of these estimates lies in that they are based on where people live and not where people are injured, which may overestimate the access to trauma centers for seriously injured patients in fatal crashes. Method: In this study, the Fatality Analysis Reporting System (FARS) data between 2013 and 2014 were collected and analyzed to quantify the access of injured patients to trauma centers for fatal crashes across states. Two types of distance, linear distance and route distance, were calculated using ArcGIS. The estimated transport time to the nearest level I/II trauma center was also calculated and compared to the recorded on-scene and transport time. Results and Conclusions: The Northeast region had the nearest average linear and route distance between fatal crash and trauma center (25.3 km and 31.7 km, respectively), followed by the Midwest (44.4 km and 54.1 km), the South (47.3 km and 57.0 km), and the West (50.9 km and 67.5 km). The comparison between the estimated and actual transport time revealed that the different states adopted different trauma triage protocols, resulting in different utilization rates of the level I/II trauma center among states. A linear regression analysis demonstrated that the longer the average route distance, the less the seriously injured patients in fatal crashes were taken to level I/II trauma center directly. Practical applications: These findings may help to identify the access to trauma centers for road crashes and the variation of delivery ratio to trauma center among the states, therefore a better utilization of trauma centers for road crashes can be achieved for the emergency medical services (EMS) systems.     

Removal mechanism of trace oxytetracycline by aerobic sludge

To investigate the mechanism of removal of selected pharmaceuticals in activated sludge systems, laboratory-scale batch experiments were conducted to assess the adsorption and degradation behavior of trace oxytetracycline (OTC). The adsorption equilibrium of OTC was observed in 30 min and the adsorption process could be well described by a pseudo-second-order model with a rate of 0.362 L μg^?1 min^?1. The OTC adsorption rate decreased with increasing temperature and could be fitted by the Freundlich isotherm. The linear partition coefficients (K_d) were 1.19, 0.999, and 0.841 L g^?1 at temperatures of 15, 20, and 25 °C, respectively. Thermodynamic analysis revealed that the adsorption of OTC onto the inactivated sludge was spontaneous (ΔG = ?16.7 to ?17.0 kJ mol^?1), enthalpy-driven (ΔH = ?24.9 kJ mol^?1), entropy-retarded (ΔS = ?27.4 J (mol K)^?1), and predominantly a physical adsorption.     

The investigation of correlated factors of external explosion during the venting process

Experimental investigations were done in the paper for the process of venting explosion in a ϕ200 mm×400 mm cylindrical vessel. Compared with the normal venting process, the phenomenon of external explosion was observed and discussed first. Moreover, when CH₄–air mixture gases were used and the vent diameter was 55 mm, three kinds of condition were selected: ϕ=0.8, ϕ=1.0 and ϕ=1.3. And two ignition positions were selected: at the vessel center and at the bottom. Then the venting processes influenced by these factors were experimented and discussed, too.     

Removal of toluene vapour from air stream using a biofilter packed with polyurethane foam

Biodegradation of toluene vapour was investigated for 168 days in a polyurethane packed biofilter inoculated with a mixed microbial population. Biofilter consisted of five square cross-section modular units each of size 0.16 m × 0.16 m × 0.20 m and filled with the polyurethane foam cubes up to a height of 0.15 m. Inlet concentration of toluene was varied from 0.04 to 2.5 g m^?3 and the volumetric flow rate of toluene loaded air from 0.06 to 0.90 m³ h^?1.Depending upon initial loading rates, removal efficiency ranging from 68.2 to 99.9% and elimination capacity ranging from 10.85 to 90.48 g h^?1 m^?3 were observed during steady state operations. More than 90% removal efficiency was observed up to an inlet loading rate of 76.3 g h^?1 m^?3. High carbon recovery (>90%) indicated effective biodegradation in the bed. Low variation of pH (7.2–8.8) and pressure drop (45.8–76.3 Pa) was observed. The stability of the biomass was evident from the fast response of the biofilter to shutdown and restartup.     

Nursing student evaluation of NIOSH workplace violence prevention for nurses online course

Introduction: As primary targets of workplace violence in health care settings, nurses may suffer negative physical and psychological consequences. NIOSH created an online course to educate nurses about violence prevention techniques. Method: A mixed-methods approach assessed workplace violence awareness and knowledge among nursing students. A pre/post/post-test survey and focus group discussions evaluated participant awareness and knowledge, assessed course design, and solicited recommendations for increasing participation and strategies for improving message retention. Results: The mean awareness scores differed significantly between pre-course and both post-course time points (Wilk's λ = 0.319, F(2, 46) = 49.01, p < 0.001). Post hoc tests using the Bonferroni correction revealed that course participation increased awareness of workplace violence from pre-course scores (M = 0.75, SD = 0.438) to immediate post-course (M = 2.13, SD = 0.789) and four-week post-course (M = 1.96, SD = 0.771) scores on a 3-item measure. Similarly, mean knowledge scores increased between pre-course and both post-course time points (Wilk's λ = 0.495, F(1.57, 73.66) = 37.26, p < 0.001). Post hoc tests using the Bonferroni correction revealed that course participation increased knowledge of workplace violence from pre-course scores (M = 6.65, SD = 1.45) to immediate post-course (M = 8.56, SD = 1.32) and four-week post-course (M = 8.19, SD = 1.42) scores on a 10-item measure. Qualitative data from the focus groups reinforced the quantitative findings. Participants citing benefits from the content strongly recommended including the course in nursing curriculums. Incorporating the course early in the nursing educational experience will better prepare students to deal with workplace violence when they enter health care professions. Conclusions: The results indicate that NIOSH and its partners created an effective online workplace violence awareness and prevention course. Practical applications: Nursing students and professionals can be effectively educated about workplace violence using an online format.     

Conscientious personality and young drivers' crash risk

Introduction: Personality characteristics are associated with many risk behaviors. However, the relationship between personality traits, risky driving behavior, and crash risk is poorly understood. The purpose of this study was to examine the association between personality, risky driving behavior, and crashes and near-crashes, using naturalistic driving research methods. Method: Participants' driving exposure, kinematic risky driving (KRD), high-risk secondary task engagement, and the frequency of crashes and near-crashes (CNC) were assessed over the first 18 months of licensure using naturalistic driving methods. A personality survey (NEO-Five Factor Inventory) was administered at baseline. The association between personality characteristics, KRD rate, secondary task engagement rate, and CNC rate was estimated using a linear regression model. Mediation analysis was conducted to examine if participants' KRD rate or secondary task engagement rate mediated the relationship between personality and CNC. Data were collected as part of the Naturalistic Teen Driving Study. Results: Conscientiousness was marginally negatively associated with CNC (path c = − 0.034, p = .09) and both potential mediators KRD (path a = − 0.040, p = .09) and secondary task engagement while driving (path a = − 0.053, p = .03). KRD, but not secondary task engagement, was found to mediate (path b = 0.376, p = .02) the relationship between conscientiousness and CNC (path c′ = − 0.025, p = .20). Conclusions: Using objective measures of driving behavior and a widely used personality construct, these findings present a causal pathway through which personality and risky driving are associated with CNC. Specifically, more conscientious teenage drivers engaged in fewer risky driving maneuvers, and suffered fewer CNC. Practical Applications: Part of the variability in crash risk observed among newly licensed teenage drivers can be explained by personality. Parents and driving instructors may take teenage drivers' personality into account when providing guidance, and establishing norms and expectations about driving.     

Pretreatment of municipal landfill leachate by a combined process

Biodegradability enhancement of landfill leachate using air stripping followed by coagulation/ultrafiltration (UF) processes was introduced. The air stripping process obtained a removal efficiency of 88.6% for ammonia nitrogen (NH₄–N) at air-to-liquid ratio of 3500 (pH 11) for stripping 18 h. The single coagulation process increased BOD/COD ratio by 0.089 with the FeCl₃ dosage of 570 mg l^?1 at pH 7.0, and the single UF process increased the BOD/COD ratio to 0.311 from 0.049. However, the combined process of coagulation/UF increased the BOD/COD ratio from 0.049 to 0.43, and the final biological oxygen demand (BOD), chemical oxygen demand (COD), NH₄–N and colour of leachate were 1223.6 mg l^?1, 2845.5 mg l^?1, 145.1 mg l^?1 and 2056.8, respectively, when 3 kDa molecular weight cut-off (MWCO) membrane was used at the operating pressure 0.7 MPa. In ultrafiltration process, the average solution flux (J_V), concentration multiple (M_C) and retention rate (R) for COD was 107.3 l m^?2 h^?1, 6.3% and 84.2%, respectively.     

Evaluation of an in-vehicle monitoring system (IVMS) to reduce risky driving behaviors in commercial drivers: Comparison of in-cab warning lights and supervisory coaching with videos of driving behavior

ProblemRoadway incidents are the leading cause of work-related death in the United States.MethodsThe objective of this research was to evaluate whether two types of feedback from a commercially available in-vehicle monitoring system (IVMS) would reduce the incidence of risky driving behaviors in drivers from two companies. IVMS were installed in 315 vehicles representing the industries of local truck transportation and oil and gas support operations, and data were collected over an approximate two-year period in intervention and control groups. In one period, intervention group drivers were given feedback from in-cab warning lights from an IVMS that indicated occurrence of harsh vehicle maneuvers. In another period, intervention group drivers viewed video recordings of their risky driving behaviors with supervisors, and were coached by supervisors on safe driving practices.ResultsRisky driving behaviors declined significantly more during the period with coaching plus instant feedback with lights in comparison to the period with lights-only feedback (ORadj = 0.61 95% CI 0.43–0.86; Holm-adjusted p = 0.035) and the control group (ORadj = 0.52 95% CI 0.33–0.82; Holm-adjusted p = 0.032). Lights-only feedback was not found to be significantly different than the control group's decline from baseline (ORadj = 0.86 95% CI 0.51–1.43; Holm-adjusted p > 0.05).ConclusionsThe largest decline in the rate of risky driving behaviors occurred when feedback included both supervisory coaching and lights.Practical applicationsSupervisory coaching is an effective form of feedback to improve driving habits in the workplace. The potential advantages and limitations of this IVMS-based intervention program are discussed.     

Investigation on removal of p-nitrophenol using a hybridized photo-thermal activated persulfate process: Central composite design modeling

The aim of this work is the study of p-nitrophenol (PNP) removal, as a nitroaromatic compound, using a hybridized photo-thermally activated potassium persulfate (KPS) in a fully recycled batch reactor. Response surface method was used for modeling the process. Reaction temperature, KPS initial dosage and initial pH of the solution were selected as variables, besides PNP degradation efficiency was selected as the response. ANOVA analysis reveals that a second order polynomial model with F-value of 41.7, p-value of 0.0001 and regression coefficient of 0.95 is able to predict the response. Based on the model, the process optimum conditions were introduced as initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 66 °C. Also experiments showed that using thermolysis and photolysis of the persulfate simultaneously, the role of thermolysis is not considerable. A pseudo first order kinetic model was established to describe the degradation reaction. Operational cost, as a vital industrial criterion, was estimated so that the condition of initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 25 °C showed the highest cost effective case. Under the preferred mild condition, the process will reach to 84% and 89% of degradation and mineralization efficiencies, after 60 and 120 min, respectively.     

Fire and Explosion Characteristics of 3-Methyl Pyridine at 270°C with High Oxygen Concentrations

The mixture of 3-methyl pyridine (3-picoline) and steam is used in the production of vitamin B3 in the gas phase. The aim of this study was to investigate the influence of inert steam (H₂O) on the flammability characteristics of 3-picoline in the manufacturing process. Four practical vapour mixing ratios of 3-picoline/steam mixtures, 5, 10, 30 and 100 vol% 3-picoline, were selected in this study. A series of flammability tests were employed for determining their fire and explosion characteristics. Fire tests H₂O: 3-picoline 5,10, 30 and 100 vol% were carried out in a 20-L-Apparatus under simulated conditions of 760 mmHg, 270°C, together with high oxygen concentrations (42 and 21 vol%) used in the real process.The experimental results showed that the safety-related parameters and flammability hazard degrees were all able to be significantly reduced while substantial amount of steam was infused into the 3-picoline/steam system. While the steam proportion was up to 97 vol%, 3-picoline/steam would be non-flammable. As a result, dosing steam to the process is one of the effective methods to prevent the relevant processes from incurring fire and explosion hazards, not to mention its economical benefit.     

Prevalence of work-site injuries and relationship between obesity and injury among U.S. workers: NHIS 2004–2012

Introduction: Studies have reported associations between obesity and injury in a single occupation or industry. Our study estimated the prevalence of work-site injuries and investigated the association between obesity and work-site injury in a nationally representative sample of U.S. workers. Methods: Self-reported weight, height, and injuries within the previous three months were collected annually for U.S. workers in the National Health Interview Survey (NHIS) from 2004–2012. Participants were categorized as normal weight (BMI: 18.5–24.9 kg/m²), overweight (BMI: 25.0–29.9), obese I (BMI: 30.0–34.9), and obese II (BMI: 35 +). The prevalence of injury and prevalence ratios from fitted logistic regression models was used to assess relationships between obesity and injury after adjusting for covariates. Sampling weights were incorporated using SUDAAN software. Results: During the 9-year study period from 2004 to 2012, 1120 workers (78 workers per 10,000) experienced a work-related injury during the previous three months. The anatomical sites with the highest prevalence of injury were the back (14.3/10,000 ± 1.2), fingers (11.5 ± 1.3), and knees (7.1 ± 0.8). The most common types of injuries were sprains/strains/twists (41.5% of all injuries), cuts (20.0%), and fractures (11.8%). Compared to normal weight workers, overweight and obese workers were more likely to experience work-site injuries [overweight: PR = 1.25 (95% CI = 1.04–1.52); obese I: 1.41 (1.14–1.74); obese II: 1.68 (1.32–2.14)]. These injuries were more likely to affect the lower extremities [overweight: PR = 1.48, (95% CI = 1.03–2.13); obese I: 1.70 (1.13–2.55); obese II: 2.91 (1.91–4.41)] and were more likely to be due to sprains/strains/twists [overweight: PR = 1.73 (95% CI = 1.29–2.31); obese I: PR = 2.24 (1.64–3.06); obese II: PR = 2.95 (2.04–4.26)]. Conclusions: Among NHIS participants, overweight and obese workers were 25% to 68% more likely to experience injuries than normal weight workers. Practical applications: Weight reduction policies and management programs may be effectively targeted towards overweight and obese groups to prevent or reduce work-site injuries.     

Educational status and organizational safety climate: Does educational attainment influence workers’ perceptions of workplace safety?

From a practical perspective, understanding the impact of education on perceptions of workplace safety would benefit management’s decisions regarding workers’ adaptability, general work effectiveness, accident frequency, implementation of safety management policies, and handling of education-related accident characteristics. The current study thus examined the relationship between educational attainment and (i) safety perception, (ii) job satisfaction, (iii) compliance with safety management policies, and (iv) accident frequency. Participants were Ghanaian industrial workers (N = 320) categorized into four educational groups based on their responses: basic education 50% (n = 159); secondary education, n = 98 (30%); vocational/professional education, 17% (n = 56); and university education, 3% (n = 7). Workplace safety perception was assessed with Hayes et al.’s 50-item Work Safety Scale (WSS): a scale that effectively captures the dimensions identified by safety experts to influence perceptions of workplace safety. Multivariate analysis (MANOVA) was used to test for differences of statistical significance. Posterior comparison with t-test consistently revealed significant differences between the two higher-educated cohorts and their lower-educated counterparts. The results indicated a positive association between education and safety perception. Higher-educated workers recorded the best perceptions on safety, indicated the highest level of job satisfaction, were the most compliant with safety procedures and recorded the lowest accident involvement rate.