基于VSP2的引发剂质量分数对醋酸乙烯聚合反应失控特性及安全泄放设计影响研究

为了解决醋酸乙烯聚合反应失控所引起的超压问题,通过VSP2绝热量热仪研究了醋酸乙烯聚合反应的失控特性,并通过Leung's法对某醋酸乙烯聚合反应器的安全泄放面积进行了计算;然后,在其他条件不变的情况下,研究引发剂质量分数对失控特性和泄放面积的影响,结果表明,引发剂质量分数对反应总放热量的影响不大,体系绝热温升为105~115℃;但引发剂质量分数越大,失控反应的最大温升速率和最大压升速率越大。这是因为引发剂质量分数越大,在相同泄放压力和最大累积压力下,单位质量反应物的放热速率就越大,也就需要更大的泄放面积;最后,引入无量纲数W~*、G~*和A~*,拟合出它们与引发剂质量分数X*的关系式,结果表明,在研究范围内所需安全泄放面积随引发剂质量分数线性增大。     

过氧丙酸分解反应的失控泄放特性研究

为研究过氧丙酸分解反应的失控泄放特性,利用泄放模式实验装置对过氧丙酸在不同泄放口径和泄放压力下的顶部和底部的泄放过程进行了试验模拟,得到了过氧丙酸的失控特性参数和不同条件下的泄放特征。结果表明:过氧丙酸失控反应泄放易出现二次峰值现象,初次峰值为气相泄放,二次峰值为气液两相泄放;二次峰值的出现取决于泄放口径及泄放时的物料温度,与泄放压力无关;恒压泄放容易出现非平衡泄放,导致较高最大累积压力和较高的釜内物料温度;底部泄放能够使釜内物料快速排空。     

Inherent thermal runaway hazard evaluation method of chemical process based on fire and explosion index

Thermal runaway hazard assessment provides the basis for comparing the hazard levels of different chemical processes. To make an overall evaluation, hazard of materials and reactions should be considered. However, most existing methods didn't take the both into account simultaneously, which may lead the assessment to a deviation from the actual hazard. Therefore, an integrated approach called Inherent Thermal-runaway Hazard Index (ITHI) was developed in this paper. Similar to Dow Fire and Explosion Index(F&EI) function, thermal runaway hazard of chemical process in ITHI was the product of material factor (MF) and risk index (RI) of reaction. MF was an indicator of material thermal hazards, which can be determined by initial reaction temperature and maximum power density. RI, which was the product of probability and severity, indicated the risk of thermal runaway during the reaction stage. Time to maximum rate under adiabatic conditions and criticality classes of scenario were used to indicate the runaway probability of the chemical process. Adiabatic temperature rise and heat of the desired reaction and secondary reaction were used to determine the severity of runaway reaction. Finally, predefined hazard classification criteria was used to classify and interpret the results obtained by this method. Moreover, the method was validated by case studies.     

Calorimetric study of the inhibition of runaway reactions during methylmethacrylate polymerization processes

Reaction inhibition was adopted as a method to halt runaway phenomena during polymerization experiments. Use of reaction calorimetry coupled with a particular system for early detection of the onset of runaway (early warning detection system) has allowed to investigate the behaviour of two substances that can influence the reaction rate: hydroquinone and 1,4-benzoquinone. The process studied was the free-radical polymerization of methylmethacrylate carried out under batch conditions in bulk or in emulsion. The results show that hydroquinone and 1,4-benzoquinone behave differently: the first is an inhibitor because it completely stops the process; the second behaves as a retarder and could be used industrially to control the process and keep the reactor temperature within safe limits.     

A general criterion to define runaway limits in chemical reactors

A general runaway criterion valid for single as well as for multiple reaction types, i.e. consecutive, parallel, equilibrium, and mixed kinetics reactions, and for several types of reactors, i.e. batch reactor (BR), semibatch reactor (SBR) and continuous stirred tank reactor (CSTR) has been developed. Furthermore, different types of operating conditions, i.e. isoperibolic and isothermal (control system), have been analysed. The criterion says that we are in a runaway situation when the divergence of the system becomes positive (div>0) on a segment of the reaction path. The results show that this is a general runaway criterion than can be used to calculate the runaway limits for chemical reactors. The runaway limits have been compared with previous criteria. A considerable advantage, over existing criteria, is that it can be calculated on-line using only temperature measurements and, hence, it constitutes the core of an early warning runaway detection system we are developing.     

Comparison of criteria for prediction of runaway reactions in the sulphuric acid catalyzed esterification of acetic anhydride and methanol

Loss of temperature control is one of the major reasons that can lead to runaway reaction. This occurrence is commonly named thermal runway. The aim of this paper is the application of thermal runaway criteria in order to predict the onset of runaway phenomena and define the range of stability related to operating conditions in the reactor, with specific reference to the esterification of acetic anhydride and methanol catalysed by sulphuric acid tested in isoperibolic conditions. The isoperibolic calorimeter has also been used to obtain thermodynamic, kinetic and physical chemistry data necessary to develop a model for the reaction. Some runaway criteria applied in this work require a model for the process, so a model for the analyzed system been developed.Because of the modest reaction enthalpy and low activation energy this reacting system provide a severe test to the runaway criteria.In this work, various runaway criteria have been applied to the experimental and simulated data and the results obtained have been compared.     

反应失控型火灾爆炸事故预测

介绍了一种预测反庆失控灾害的方法,通过实验测定容器的时间常数,预测能够引起反应失控的最低环境温度,发生反应失控时的危险温度,以及达到最大反应速度反需的时间,预测结果与实际情况具有良好的一致性。     

Thermal risk in batch reactors: Case of peracetic acid synthesis

The present paper deals with accidents risk in batch reactors. It identifies the conditions for the occurrence of a thermal runaway and develops a probabilistic approach to assess the relevant risk. It investigates also the conditions for optimal synthesis of peracetic acid (PAA) with hydrogen peroxide (HP) and acetic acid (AA). The kinetic model of reversible reaction and side reaction of PAA synthesis is used to predict reactor temperature and molar ratio of PAA by ASPEN PLUS software. A sensitivity analysis is performed under different conditions such as constant temperature or adiabatic process with different concentrations of sulfuric acid. Assuming a prior cooling system failure, the conditions for reaction runaway triggering a thermal accident are identified in the case of PAA synthesis. Monte Carlo simulations are used in order to calculate the conditional probability of accident and optimize the synthesis of PAA.     

Thermal hazards analysis of styrene in contact with impurities

Styrene is a reactive monomer commonly used to produce polystyrene and other copolymers. Unintended thermal runaway polymerization reactions of styrene keep reoccurring and have led to catastrophic consequences. One of the possible causes of these runaway incidents involves the contamination of the styrene monomer by incompatible species, which was not adequately investigated and documented. This study focuses on the quantification of thermal runaway hazards of styrene in contact with a series of contamination substances by adopting calorimetric analysis. Both Differential Scanning Calorimeter (DSC) and Advanced Reactive System Screening Tool (ARSST) were employed to examine the exothermic characteristics of styrene mixed with contaminating substances at different concentration levels and mixing conditions. Key safety parameters of the exothermic reaction, such as the onset temperature, the overall heat release, the maximum self-heating rate, as well as the activation energy, were obtained. The results indicated that the thermal runaway polymerization of purified styrene was significantly altered by the presence of contaminant species. Water effectively retarded and quenched the runaway polymerization at a higher temperature range. Alkaline had no substantial effect on the thermal runaway characteristics. The presence of acid solution under both static contact and vigorous mixing condition significantly promoted the thermal polymerization of styrene. A trace amount of concentrated acid initiated violent exothermic activity even at room temperature; and the severity of the reaction was profoundly impacted by the mass-transfer. Our study demonstrates significant implications in the prevention of runaway incidents during transportation and storage of styrene.     

A comparative analysis between temperature and pressure measurements for early detection of runaway initiation

In this work, we have analysed the use of pressure instead of temperature measurements for the early warning detection of runaway initiation. This is possible due to the fact that our runaway criterion, i.e. div>0, does not depend specifically on which state space variable we are using for divergence calculation. A series of runaway experiments, carried out in a 250 l pilot-scale reactor, has been used to compare the results. In accordance with previous analysis, we show that by using temperature, early detection of runaway initiation is achieved. Analogously to temperature, pressure may be also used for runaway detection. By comparing the different types of reactive systems analysed (vapour and gassy), it can be observed that temperature works better, in terms of earlier detection, than pressure but the differences are more pronounced for vapour than for gassy systems.     

On the divergence criterion for runaway detection: Application to complex controlled systems

It is well-known that, for certain values of the operative parameters influencing the dynamic behavior of a chemical reactor, a phenomenon known as thermal runaway (that is, a loss of the reactor temperature control) may arise. Such a situation can be really dangerous because above a certain threshold temperature value unwanted side reactions or, worse, decompositions of the reacting mixture may be triggered evolving high amounts of flammable or toxic gases that can cause reactor pressurization and, eventually, its explosion. For this reason, since the beginning of the previous century a number of studies concerning the prediction of the so called runaway boundaries has been carried out. In this work, a modified version of the divergence criterion for runaway detection, originally developed by Zaldívar and co-workers, is presented. Such a modified divergence criterion is capable of treating whatever type of complex controlled reacting system (taking into account not only temperature control but also dosing strategies) and its reliability has been demonstrated for isoperibolic semibatch reactors using literature experimental data concerning the nitration of 4-Chlorobenzotrifluoride in mixed acids and the nitric acid oxidation of 2-octanol to 2-octanone and further carboxylic acids.     

交联剂TAIC反应风险评估分析

利用全自动反应量热仪和绝热加速量热仪等相关实验仪器检测出TAIC(三烯丙基异氰尿酸酯)合成反应的反应热、比热容及热稳定性等数据,依据绝热温升、工艺温度、技术最高温度、最大反应速率到达时间及失控体系可能达到的最高温度这5个温度参数按照评估标准从分解热、严重度、可能性、矩阵、工艺危险度这5个方面分别进行评估。通过对热参数及实验过程进行分析提出降低工艺危险等级的工艺优化方法。根据最终评估结果对TAIC生产装置的安全性进行评价,提出相应的整改措施及建议。     

Setting optimal operating conditions for a catalytic reactor for butane oxidation using parametric sensitivity analysis and failure probability indices

Safe operation of a catalytic reactor remains a sensitive issue when highly exothermic reactions are conducted and hazardous side reactions may occur. Derivation of the optimal operating conditions must include economic but also safety criteria, technological constraints, beside controllability and stability aspects. The present work introduces a criterion based on a joint failure probability index related to uncertainty in the runaway boundaries and the random disturbances of the operating parameters. The use of such a safety criterion is even more important when setting the optimal operating policy of the reactor in the vicinity of the runaway boundaries that often correspond to a high productivity. The paper indicates how an economically efficient but more prudent operating policy can be selected, by simultaneously considering the economic and safety objectives. An example is provided for the case of an industrial fixed-bed tubular reactor, of high thermal sensitivity, used for the catalytic oxidation of butane to maleic anhydride in vapour phase. The multi-objective optimization can lead to a prudent trade-off operating solution (corresponding to a failure probability of maximum 3–4%) that limits the reactor productivity. Being based on a local and global sensitivity analysis of the reactor, the proposed rule is generally applicable by minimizing the probability with which control variables violate their safety limits.     

BIPB的热分解动力学和失控反应模拟

为了评估双(叔丁过氧基)二异丙苯(BIPB)的热危害,对其热分解过程进行多速率的动态扫描C80热分析,用几种简单的热危害评估方法分析其热危害。然后应用模式法、无模式法(Friedman微分等转化率法)分别对试验结果进行处理,得到分解动力学数据,并用ASTM E 698法得到活化能数据,同时用C80、ARC和DSC的试验数据验证分解动力学数据的可靠性。最后利用无模式法的分解动力学数据进行BIPB绝热条件下和非绝热的2m3球形容器中的失控反应模拟,得到类似工艺条件下BIPB的安全控制温度。     

Hazard evaluation for chlorination and amination reactions of fluorocytosine production process

Reaction thermal runaway is one of the most important reasons leading to chemical accidents. With the rapid development of the chemical industry in the world, especially the fine chemical industry, various safety accidents also occur frequently. Therefore, it is necessary to study the exothermic behavior of the reaction process. In this study, reaction calorimeter was used to study the exothermic phenomena during the chlorination reaction and amination reaction. Differential scanning calorimetry was performed on the reactants, and thermogravimetric experiments were performed on the products. In addition, adiabatic experiment was performed to study the thermal runaway behavior of amination products under adiabatic conditions. The results showed that the target reactions generated a large amount of heat in the initial stage. The maximum temperature of amination reaction is higher than the initial decomposition temperature of the amination product under adiabatic condition. The pyrolysis of amination product was divided into three stages. The product had a high apparent activation energy at the beginning of decomposition, and the apparent activation energy decreased as the decomposition progressed.     

苯和甲苯硝化及磺化反应热危险性分级研究

首先介绍了化工工艺热安全性的内涵,并从反应过程热危险性分析的方法学出发,介绍间隙、半间歇化学反应工艺热危险性分级研究的总体思路及方法。然后,围绕甲苯和苯的硝化、磺化反应,用全自动反应量热仪(RC1e)和加速度量热仪(ARC)测定其反应过程的绝热温升(△Tad)、目标反应所能达到的最高温度(TM)、分解反应最大速率到达时间(θD)等参数。运用风险评价指数矩阵法(方法1)和基于失控过程温度参数的热危险评估法(方法2)分别对其硝化和磺化反应过程的热危险性进行了分级评估。结果表明,这两种方法具有良好的一致性;给定工艺条件下甲苯和苯的一段硝化反应过程的热危险度等级较低;而磺化反应的热危险较高。尽管这两种方法还有一定的局限性,但对于间歇、半间歇合成工艺的本质安全化设计、工艺热危险性的评估具有重要的参考价值和实用意义。     

Thermal hazard assessment for synthesis of 3-methylpyridine-N-oxide

The exothermic oxidation of 3-methylpyridine with hydrogen peroxide was analyzed by Reaction Calorimeter (RC1e) in semi-batch operation. Heat releasing rate and heat conversion were studied at different operating conditions, such as reaction temperature, feeding rate, the amount of catalyst and so on. The thermal hazard assessment of the oxidation was derived from the calorimetric data, such as adiabatic temperature rise (ΔT_ad) and the maximum temperature of synthesis reaction (MTSR) in out of control conditions. Along with thermal decomposition of the product, the possibility of secondary decomposition under runaway conditions was analyzed by time to maximum rate (TMR_ad). Also, risk matrix was used to assess the risk of the reaction. Results indicated that with the increase of the reaction temperature, the reaction heat release rate increased, while reaction time and exotherm decreased. With the increase of feeding time, heat releasing rate decreased, but reaction time and exotherm increased. With the amount of the catalyst increased, heat releasing rate increased, reaction time decreased and exothermic heat increased. The risk matrix showed that when the reaction temperature was 70 °C, feeding time was 1 h, and the amount of catalyst was 10 g and 15 g, respectively, the reaction risk was high and must be reduced.     

Using thermal analysis with kinetic calculation method to assess the thermal stability of azo compound on construction materials

The application of construction polymers in engineering and alternative materials has always occupied a place in the market. In the production process of polymer resins, initiators can be used to lower the polymerization reaction energy threshold, which can improve reaction efficiency and reduce energy loss. However, as a commonly used energetic substance in the polymerization process, azos have caused related process hazards due to their exothermic characteristics. Because of this, it is essential to examine and analyze the thermal hazard characteristics of emerging azo substances, such as 2-cyanopropan-2-imemicarbazide (CABN). Although previous literature performs the calculation on related thermal hazard parameters of CABN, there is still exists a void for discussion in estimating the reaction model to avoid analogous hazards and enhance the existing thermal analysis. Based on the past literature, the reaction model is improved with thermogravimetric analysis as evidence. The revised thermal hazard parameters are calculated as the basis of control and mitigation measures, the kinetic model is used to estimate the modified safety parameters, and in the judgment of the runaway reaction, the critical temperature of the runaway is found by analyzing the influence of slight changes in ambient temperature on the reaction temperature. The results show that the critical temperature that causes CABN to enter the runaway reaction is delayed, and the hazard is lower than in the storage situation. Therefore, the thermal hazard to CABN mainly focuses on the safety environment and measures during storage.     

Evaluating time to maximum rate (TMR) and self-accelerating decomposition temperature (SADT) of self-polymerizing vinyl acetate monomer

Vinyl acetate monomer (VAM) is widely used as a chemical intermediate producing a variety of copolymer products. Besides, VAM has the tendency to readily decompose into free radicals and ions that initiates the self-sustaining polymerization reaction. The non-isothermal experiments of VAM were performed using differential scanning calorimetry (DSC), and the calculations of the kinetic parameters from temperature-programmed DSC curves have been evaluated by the isoconversional method. The thermal analysis of VAM was proceeded using the advanced thermal analysis software (AKTS) to figure out the time to maximum rate (TMR) and self-accelerating decomposition temperature (SADT) for a proactive safety design of VAM. Subsequently, the kinetic model is used to predict the potential thermal runaway in the VAM-PVAc polymerizing process.