Nickel and sulfur speciation of residual oil fly ashes from two electric utility steam-generating units

Representative duplicate fly ash samples were obtained from the stacks of 400- and 385-MW utility boilers (Unit A and Unit B, respectively) using a modified U.S. Environmental Protection Agency (EPA) Method 17 sampling train assembly as they burned 0.9 and 0.3 wt % S residual (No. 6 fuel) oils, respectively, during routine power plant operations. Residual oil fly ash (ROFA) samples were analyzed for Ni concentrations and speciation using inductively coupled plasma-atomic emission spectroscopy, X-ray absorption fine structure (XAFS) spectroscopy, and X-ray diffraction (XRD). ROFA deionized H2O extraction residues were also analyzed for Ni speciation using XAFS and XRD. Total Ni concentrations in the ROFAs were similar, ranging from 1.3-1.5 wt%; however, stack gas Ni concentrations in the Unit A were 0.990 microg/Nm3 compared with 0.620 microg/Nm3 for Unit B because of the greater residual oil feed rates employed at Unit A to attain higher 400-MW load conditions with a lower heating value oil. Ni speciation analysis results indicated that ROFAs from Unit A contain approximately 3 wt % NiSO4 x xH2O (where x is assumed to be 6 for calculation purposes) and appoximately 4.5 wt% of a Ni-containing spinel compound, similar in composition to (Mg,Ni)(Al,Fe)2O4. ROFAs from Unit B contain on average 2 wt% NiSO4 x 6 H20 and 1.1 wt% NiO. XAFS and XRD analyses did not detect any nickel sulfide compounds, including carcinogenic nickel subsulfide (Ni3S2) (XAFS detection limit is 5% of the total Ni concentration). In addition, XAFS measurements indicated that inorganic sulfate and organic thiophene species accounted for > 97% of the total S in the ROFAs. Unit A ROFAs contained much lower thiophene proportions because cyclone-separated ROFA reinjection is employed on this unit to collect and reburn the larger carbonaceous particles.     

Comparison of hematite/Fe(II) systems with cement/Fe(II) systems in reductively dechlorinating trichloroethylene

Reactive reductants of cement/Fe(II) systems in dechlorinating chlorinated hydrocarbons are unknown. This study initially evaluated reactivities of potential reactive agents of cement/Fe(II) systems such as hematite (alpha-Fe(2)O(3)), goethite (alpha-FeOOH), lepidocrocite (gamma-FeOOH), akaganeite (beta-FeOOH), ettringite (Ca(6)Al(2)(SO(4))(3)(OH)(12)), Friedel's salt (Ca(4)Al(2)Cl(2)(OH)(12)), and hydrocalumite (Ca(2)Al(OH)(6)(OH).3H(2)O) in reductively dechlorinating trichloroethylene (TCE) in the presence of Fe(II). It was found that a hematite/Fe(II) system shows TCE degradation characteristics similar to those of cement/Fe(II) systems in terms of degradation kinetics, Fe(II) dose dependence, and final products distribution. It was therefore suspected that Fe(III)-containing phases of cement hydrates in cement/Fe(II) systems behaved similarly to the hematite. CaO, which was initially introduced as a pH buffer, was observed to participate in or catalyze the formation of reactive reductants in the hematite/Fe(II) system, because its addition enhanced the reactivities of hematite/Fe(II) systems. From the SEM (scanning electron microscope) and XRD (X-ray diffraction) analyses that were carried out on the solids from hematite/Fe(II) suspensions, it was discovered that a sulfate green rust with a hexagonal-plate structure was probably a reactive reductant for TCE. However, SEM analyses conducted on a cement/Fe(II) system showed that hexagonal-plate crystals, which were presumed to be sulfate green rusts, were much less abundant in the cement/Fe(II) than in the hematite/Fe(II) systems. It was not possible to identify any crystalline minerals in the cement/Fe(II) system by using XRD analysis, probably because of the complexity of the cement hydrates. These observations suggest that major reactive reductants of cement/Fe(II) systems may differ from those of hematite/Fe(II) systems.     

Catalytic oxidation processes for removing dimethylsulfoxide from wastewater

An effective method for removing dimethylsulfoxide (DMSO) from wastewater, based on the mild selective catalytic sulfoxidation with H(2)O(2), is proposed in this study. The catalysts are W-containing layered double hydroxides (LDH), and they were obtained by ionic exchange of the nitrate anions from MAl-LDH precursors (M=Mg(2+) or Zn(2+)) with both WO(4)(2-) and W(7)O(24)(6-) species. Results of X-ray diffraction (XRD), N(2) adsorption, thermal gravimetric analysis (TGA), diffuse reflectance ultraviolet spectroscopy (DRUV) and Raman spectroscopy confirmed the formation of the W-oxospecies inside the interlayer space and the modification of the textural properties upon the exchange process. All catalysts showed very good activity and stability in the DMSO conversion into dimethylsulfone with dilute H(2)O(2) aqueous solution, at low temperatures (20-50 degrees C). The efficiency of the H(2)O(2) was higher than 95% and the behaviour of the water as solvent was very close to that of the organic solvents (ethanol, acetonitrile, 1,4-dioxane).     

Mineralization of aged atrazine and mecoprop in soil and aquifer chalk.

The effect of ageing on the bioavailability and sorption of the herbicides atrazine and mecoprop was studied in soil and aquifer chalk sampled at an agricultural field near Aalborg, Denmark. The herbicides were incubated in sterile soil or chalk up to 3 months prior to inoculation with 5 x 10(7) cells g(-1) (dry weight) of a mecoprop degrading highly enriched culture (PM) or 1 x 10(9) cells g(-1) (dry weight) of the atrazine degrading Pseudomonas sp. strain ADP. As a measure of the bioavailable residues accumulated 14CO2 was measured for 2 months. In both soil and chalk ageing limited the rate of atrazine mineralization, and in chalk the extent of mineralization was reduced as well. The fraction of sorbed atrazine in the soil ranged between 50% and 62%, whereas a maximum of 12% was sorbed in chalk. No impact on the mineralization of aged mecoprop was seen as no sorption of this herbicide on either soil or chalk was measured.     

Oxidation of volatile organic compounds on SBA-15 mesoporous molecular sieves modified with manganese

Catalytic combustion of volatile organic compounds, such as propene, has been studied on manganese modified mesoporous molecular sieves. Powder X-ray diffraction, (29)Si nuclear magnetic resonance, nitrogen sorption and transmission electron microscopy show that the SBA-15 mesoporous silica molecular sieve can be modified with manganese using Mn(2)(CO)(10) or Mn(O(2)CMe)(2) without significant distortion of the host structure. The two products were catalytically active in propene oxidation, with SBA-15 modified with Mn(2)(CO)(10) showing significantly higher activity, possibly due to higher Mn content, than SBA-15 modified with Mn(O(2)CMe)(2).     

Evaluation of boron removal from water by hydrotalcite-like compounds

Layered double hydroxides (LDHs) or hydrotalcite (HT)-like compounds with different kinds of metal ions (Mg-Al and Mg-Fe) in the brucite-like sheets were prepared and their adsorption properties were studied in the boron removal from aqueous solution under laboratory conditions. The hydrotalcites were synthesized by the coprecipitation method and were characterized by chemical analyses, X-ray diffraction (XRD), Fourier Transform infrared spectroscopy (FTIR) and specific surface area measurements (BET). The affinity of these materials with a mixture of B(OH)(3) and B(OH)(4)(-) was studied as a function of contact time, initial pH of the solutions, HT quantity and B concentration (adsorption isotherms). It was found that 120 min is enough time for the equilibrium state to be reached in boron adsorption. Boron removal was independent of the initial pH of the solutions because of the high buffering capacity of the LDHs. On the other hand, the adsorption capacity increases with increasing the adsorbent quantity. The adsorption isotherms, described by the Langmuir model, are of L-type, suggesting that B(OH)(4)(-) is adsorbed preferentially on HT-like materials. Besides, Mg-Al hydrotalcites showed higher adsorption capacity than Mg-Fe. We proposed that in Mg-Al hydrotalcites, the boron removal occurs by both adsorption on external surface and ion exchange, whereas for Mg-Fe it occurs only by surface adsorption. After treatment of a solution containing 5.2 mgBl(-1) with Mg-Al hydrotalcites the final boron concentration reached the recommended limit by WHO for drinking water (0.5 mgl(-1)).     

稻壳基活性炭的制备及其对亚甲基蓝吸附的研究

以稻壳为原料，采用K2CO3活化法和H3P04活化法制备了比表面积为1312m^2／g和682m^2／g的活性炭，通过扫描电子显微镜（SEM）、X-射线衍射仪（XRD）对样品进行了表征，并将孔隙发达的活性炭样品用于对亚甲基蓝的吸附，结果表明，K2CO3活化法制备的活性炭样品具有更多的微孔结构；随着亚甲基蓝溶液初始浓度的增加、活性炭吸附时间的延长，亚甲基蓝的去除率呈现逐渐降低和逐渐增大的变化规律，当pH值为6时，活性炭对亚甲基蓝的吸附效果最佳；稻壳基活性炭对亚甲基蓝的吸附等温线符合Langmuir模型，Qm最高可达476．2mg／g；热力学参数△G^0△H^0和△S^0均为负值，表明稻壳基活性炭对亚甲基蓝的吸附是一个自发的放热反应。     

Molecular study of concentrated copper pollutant with a compost

Humic substance in compost contains various organic functional groups that can sorb metal ions through ionic force. This study used thermal treatment technology to concentrate copper in the heated residues while destroying the humic substance of copper-sorbed kitchen compost. Scanning electron microscopy (SEM) results show that copper clusters were formed in the heated residues. Information from both X-ray diffraction (XRD) patterns and Cu K-edge X-ray absorption spectroscopy (XAS) spectrum indicates that about 30% of the doped Cu(II) was chemically reduced to Cu(I) and Cu(0) when the sample was heated at 500 and 900 degrees C for 2h. The XAS results indicate that after 500 degrees C thermal treatment, the loaded Cu(NO(3))(2) was transformed into CuO (ca. 54%), Cu (ca. 18%), Cu(OH)(2) (ca. 15%), and Cu(2)O (ca.13%). Heating at 900 degrees C caused more transformation into elemental Cu probably due to more release of oxygen.     

Sorption of organic contaminants in a fractured chalk formation

Sorption capability of bedrock components from a fractured chalk province was evaluated using ametryn, phenanthrene, m-xylene, 2,4,6-tribromophenol, and 1,2-dichloroethane. Sorption isotherms for the four aromatic compounds were nonlinear on gray (unoxidized) chalk. Over the studied solution ranges, the distribution coefficient decreased by factor of 3 for phenanthrene and m-xylene, a factor 4 for ametryn, and by an order of magnitude for 2,4,6-tribromophenol. In contrast, 1,2-dichloroethane displayed a linear isotherm. The importance of polar interactions for ametryn sorption was evaluated by normalizing sorption to an "inert" solvent, n-hexane. n-Hexane-normalized sorption of ametryn was much greater than that of phenanthrene, presumably due to ametryn participation in hydrogen bonding interactions. In sharp contrast to sorption to gray chalk, sorption to white (oxidized) chalk is 100- to 1000-fold lower at any given solution concentration. The much greater sorption on gray chalk cannot be explained by specific surface area, clay content, or organic matter content; thus, the nature of the organic matter is considered to control sorption in the chalk samples. Gray chalk sorption capacity estimates for ametryn and 2,4,6-tribromophenol are similar, which, together with evidence of competition for sorption sites, suggests that the limited capacity sorption domain for both compounds is similar.     

Lead and other metals distribution in local cooking salt from the Fofi salt- spring in Akwana, Middle Benue Trough, Nigeria

Energy Dispersive X-ray Fluorescence (EDXRF) technique has been used to determine the concentrations of lead(Pb) and other heavy metals in local cooking salts (LCS) from Akwana village, Middle Benue Trough, Nigeria. The comparison of the distribution of these metals in LCS, 'fake' salt (FS) and the usual common salts (CS) are given. Lead was found to be enriched in LCS by factor exceeding 200 times compared to the other salts. The origin of Pb contamination in the LCS is examined and its effects on the inhabitants of the village are considered.     

超声辅助La-TiO2/膨胀珍珠岩的吸附与光催化性能

以膨胀珍珠岩(expanded perlite,EP)为载体,以钛酸正丁酯和硝酸镧为前驱体,采用浸渍法制备出掺杂镧的漂浮型La-TiO2/EP光催化剂,采用X-射线粉末衍射研究了催化剂的形态结构。以正辛烷为模拟水面烃类污染物,通过超声波辅助对此催化剂的吸附与光催化性能进行了研究。结果表明:以20～40目的膨胀珍珠岩为载体制备的5%La-TiO2/EP,经500℃焙烧2 h后对辛烷的去除效果最好。超声波可促进辛烷在催化剂表面的吸附与迁移,超声辅助下辛烷去除率可提高11.08%。     

Effect of anions and cations on cadmium sorption kinetics from aqueous solutions by chitin: experimental studies and modeling

The effect of ions, including Na(+), Mg(2+), Ca(2+), Cl(-), SO(4)(2-) and CO(3)(2-), at various initial concentrations, on the kinetics of cadmium sorption by chitin was studied at 25 degrees C and free initial pH solution in batch conditions. The presence of these ions in solution was found to inhibit the uptake of cadmium by chitin to different degrees: sodium and chloride ions have no significant effect. For Mg(2+), Ca(2+), SO(4)(2-) and CO(3)(2-) ions, the effects ranged from a large inhibition of cadmium by Ca(2+) and CO(3)(2-) to a weak inhibition by Mg(2+) and SO(4)(2-). These results indicate that the uptake sites of these ions are the same. No ion was found to enhance cadmium uptake. The results also showed that the kinetics of sorption are best described by a pseudo second-order expression than a first or second-order model.     

Effects of copper and palladium on the reduction of bromate by Fe(0)

Bromate reduction by Fe(0) with incorporation of copper or palladium was investigated in batch tests. The incorporation of copper led to an increase in the rate of bromate reduction, while incorporation of palladium did not show any effect on bromate reduction by Fe(0), regardless of the bimetal application techniques (either simultaneous addition of Cu(II) or Pd(IV) into the Fe-BrO3- reaction system or using copper or palladium amended iron for bromate removal). Surface analyses by X-ray photoelectron spectroscopy (XPS) and X-ray powder diffraction (XRD) techniques indicated that aqueous Cu(II) was reduced and incorporated into the iron surface to form Cu2O and Cu(0). Among these two species, pure Cu(0) is not an active electron donor to the bromate reduction reaction, as shown by there being no reduction from using Cu(0) powders alone and no enhancement by Fe(0) when physically mixed with Cu(0). Although it has been proposed in the literature that the enhancement of adsorption also contributes to the enhancement of chemical reduction, this is not the case here because adsorption decreased when Cu increased. The enhanced bromate reduction rate in the presence of copper observed here is most likely the result of the newly formed active Cu(I). The presence of PdO was evidenced by XPS but yielded no enhancement in bromate reduction. Finally, the Cu2O present on the iron surface because of copper impurities in commercially available iron was found to be involved in the bromate reduction and to accelerate the reduction rate.     

长江水絮凝污泥制备光催化剂及其催化活性

用聚硅硫酸钛絮凝处理长江水，所产生的絮凝污泥经干燥、煅烧处理后制备了具有较高催化活性的复合光催化剂，并用XRD对其进行了表征。考察了絮凝pH值、煅烧温度、絮凝剂投加量和光催化剂投加量等因素对复合光催化剂光催化降解活性艳红K-2BP溶液的影响。结果表明，当絮凝pH值为4，煅烧温度为500℃，絮凝剂投加量为0．2g／L时，制备的复合光催化剂催化活性最佳，光催化降解浓度为25mg／L的活性艳红K-2BP溶液15min后降解率达99．9％，与同等实验条件下P-25的降解效率相当。     

Effect of the Mn oxidation state and lattice oxygen in Mn-based TiO2 catalysts on the low-temperature selective catalytic reduction of NO by NH3

TiO₂-supported manganese oxide catalysts formed using different calcination temperatures were prepared by using the wet-impregnation method and were investigated for their activity in the low-temperature selective catalytic reduction (SCR) of NO by NH₃ with respect to the Mn valence and lattice oxygen behavior. The surface and bulk properties of these catalysts were examined using Brunauer-Emmett-Teller (BET) surface area, X-ray diffraction (XRD), temperature-programmed reduction (TPR), and temperature-programmed desorption (TPD). Catalysts prepared using lower calcination temperatures, which contained Mn⁴⁺, displayed high SCR activity at low temperatures and possessed several acid sites and active oxygen. The TPD analysis determined that the Brönsted and Lewis acid sites in the Mn/TiO₂ catalysts were important for the low-temperature SCR at 80～160 and 200～350 °C, respectively. In addition, the available lattice oxygen was important for attaining high NO to NO₂ oxidation at low temperatures.

Implications: Recently, various Mn catalysts have been evaluated as SCR catalysts. However, there have been no studies on the relationship of adsorption and desorption properties and behavior of lattice oxygen according to the valence state for manganese oxides (MnO_x). Therefore, in this study, the catalysts were prepared by the wet-impregnation method at different calcination temperatures in order to show the difference of manganese oxidation state. These catalysts were then characterized using various physicochemical techniques, including BET, XRD, TPR, and TPD, to understand the structure, oxidation state, redox properties, and adsorption and desorption properties of the Mn/TiO₂ catalysts.     

热镀锌厂酸洗废水和锌灰中回收硫化锌

从热镀锌厂的酸洗废水和锌灰中回收硫化锌,采用X射线能谱仪(EDS),X射线衍射仪(XRD),傅里叶红外光谱仪(FTIR)和场发射透射电镜(FETEM)表征样品ZnS性质,电感耦合等离子发射体(ICP-OES)分析上清液性质,并研究该反应动力学过程。EDS和ICP分析表明,样品ZnS纯度达到85.45%,其上清液含有高浓度铁,含量为2 g/L,可用于制备复合亚铁絮凝剂,而其他重金属离子浓度均低于电镀废水排放标准。XRD分析表明,样品ZnS是立方晶型,调节pH和采用滴加方式能有效改善样品ZnS的晶型。采用Scherrer公式计算晶体粒径,结果表明,晶粒大小在3~6 nm之间。FTIR分析表明,样品ZnS呈现良好的红外透明性,且温度、pH和滴加方式对样品的红外透光性基本没有影响。FETEM结合XRD图表明,该纳米晶呈片状,近似为球形,呈多层叠加,分散性不明显,有团聚现象。动力学实验表明,逆一级动力学方程适合描述硫化沉淀的反应动力学过程,活化能为39.04 kJ/mol,沉淀过程受化学反应和扩散联合控制。     

Modelling the migration of contaminants through variably saturated dual-porosity, dual-permeability chalk

In the Hesbaye region in Belgium, tracer tests performed in variably saturated fissured chalk rocks presented very contrasting results in terms of transit times, according to artificially controlled water recharge conditions prevailing during the experiments. Under intense recharge conditions, tracers migrated across the partially or fully saturated fissure network, at high velocity in accordance with the high hydraulic conductivity and low effective porosity (fracture porosity). At the same time, a portion of the tracer was temporarily retarded in the almost immobile water located in the matrix. Under natural infiltration conditions, the fissure network remained inactive. Tracers migrated downward through the matrix, at low velocity in relation with the low hydraulic conductivity and the large porosity of the matrix. Based on these observations, Brouyère et al. (2004a) [Brouyère, S., Dassargues, A., Hallet, V., 2004a. Migration of contaminants through the unsaturated zone overlying the Hesbaye chalky aquifer in Belgium: a field investigation, J. Contam. Hydrol., 72 (1-4), 135-164, doi: 10.1016/j.conhyd.2003.10.009] proposed a conceptual model in order to explain the migration of solutes in variably saturated, dual-porosity, dual-permeability chalk. Here, mathematical and numerical modelling of tracer and contaminant migration in variably saturated fissured chalk is presented, considering the aforementioned conceptual model. A new mathematical formulation is proposed to represent the unsaturated properties of the fissured chalk in a more dynamic and appropriate way. At the same time, the rock water content is partitioned between mobile and immobile water phases, as a function of the water saturation of the chalk rock. The groundwater flow and contaminant transport in the variably saturated chalk is solved using the control volume finite element method. Modelling the field tracer experiments performed in the variably saturated chalk shows the adequacy and usefulness of the new conceptual, mathematical and numerical model.     

Competitive sorption of organic contaminants in chalk

In the Negev desert, Israel, a chemical industrial complex is located over fractured Eocene chalk formations where transfer of water and solutes between fracture voids and matrix pores affects migration of contaminants in the fractures due to diffusion into the chalk matrix. This study tests sorption and sorption competition between contaminants in the chalk matrix to make it possible to evaluate the potential for contaminant attenuation during transport in fractures. Single solute sorption isotherms on chalk matrix material for five common contaminants (m-xylene, ametryn, 1,2-dichloroethane, phenanthrene, and 2,4,6-tribromophenol) were found to be nonlinear, as confirmed in plots of Kd versus initial solution concentration. Over the studied concentration ranges, m-xylene Kd varied by more than a factor of 100, ametryn Kd by a factor of 4, 1,2-dichloroethane Kd by more than a factor of 3, phenanthrene Kd by about a factor of 2, and 2,4,6-tribromophenol Kd by a factor of 10. It was earlier found that sorption is to the organic matter component of the chalk matrix and not to the mineral phases (Chemosphere 44 (2001) 1121). Nonlinear sorption isotherms indicate that there is at least some finite sorption domain. Bi-solute competition experiments with 2,4,6-tribromophenol as the competitor were designed to explore the nature of the finite sorption domain. All of the isotherms in the bi-solute experiments are more linear than in the single solute experiments, as confirmed by smaller variations in Kd as a function of initial solution concentration. For both m-xylene and ametryn, there is a small nonlinear component or domain that was apparently not susceptible to competition by 2,4,6-tribromophenol. The nonlinear sorption domain(s) is best expressed at low solution concentrations. Inert-solvent-normalized single and bi-solute sorption isotherms demonstrate that ametryn undergoes specific force interactions with the chalk sorbent. The volume percent of phenanthrene sorbed at the liquid solubility limit is calculated to be 13% v:v in both the single and bi-solute experiments. This value exceeds what may be reasonably interpreted as partitioning of phenanthrene into organic matter, despite the relative linearity of the phenanthrene sorption isotherm (compared with other compounds) in both single and bi-solute systems.     

H_4SiW_(12)O_(40)/TiO_2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析.研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响.实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%.     

Nondestructive characterization of municipal-solid-waste-contaminated surface soil by energy-dispersive X-ray fluorescence and low-Z (atomic number) particle electron probe X-ray microanalysis

The long-term environmental impact of municipal solid waste (MSW) landfilling is still under investigation due to the lack of detailed characterization studies. A MSW landfill site, popularly known as Dhapa, in the eastern fringe of the metropolis of Kolkata, India, is the subject of present study. A vast area of Dhapa, adjoining the current core MSW dump site and evolving from the raw MSW dumping in the past, is presently used for the cultivation of vegetables. The inorganic chemical characteristics of the MSW-contaminated Dhapa surface soil (covering a 2-km stretch of the area) along with a natural composite (geogenic) soil sample (from a small countryside farm), for comparison, were investigated using two complementary nondestructive analytical techniques, energy-dispersive X-ray fluorescence (EDXRF) for bulk analysis and low-Z (atomic number) particle electron probe X-ray microanalysis (low-Z particle EPMA) for single-particle analysis. The bulk concentrations of K, Rb, and Zr remain almost unchanged in all the soil samples. The Dhapa soil is found to be polluted with heavy metals such as Cu, Zn, and Pb (highly elevated) and Ti, Cr, Mn, Fe, Ni, and Sr (moderately elevated), compared to the natural countryside soil. These high bulk concentration levels of heavy metals were compared with the Ecological Soil Screening Levels for these elements (U.S. Environment Protection Agency) to assess the potential risk on the immediate biotic environment. Low-Z particle EPMA results showed that the aluminosilicate-containing particles were the most abundant, followed by SiO2, CaCO3-containing, and carbonaceous particles in the Dhapa samples, whereas in the countryside sample only aluminosilicate-containing and SiO2 particles were observed. The mineral particles encountered in the countryside sample are solely of geogenic origin, whereas those from the Dhapa samples seem to have evolved from a mixture of raw dumped MSW, urban dust, and other contributing factors such as wind, precipitation, weather patterns, farming, and water logging, resulting in their diverse chemical compositions and the abundant observation of carbonaceous species. Particles containing C and P were more abundant in the Dhapa samples than in the countryside soil sample, suggesting that MSW-contaminated soils are more fertile. However, the levels of particles containing potentially toxic heavy metals such as Cr, Mn, Ni, Cu, Zn, and/or Pb in the Dhapa samples were significant, corroborated by their high bulk concentration levels (EDXRF), causing deep concern for the immediate environment and contamination of the food chain through food crops.