Photocatalytic degradation of microcystin-LR in aqueous solutions

In this work, the photocatalytic degradation of aqueous microcystin-LR was studied using TiO₂ and ZnO as photocatalysts. The process was optimised and characterised at the bench scale (200 mL); both semiconductors exhibited a high degradation capacity at reaction times of 1 min (degradation greater than 95%). The transient species that were observed indicate that the degradation occurs via the multiple hydroxylation and elimination of the labile peptide residues of the molecule. When photocatalysis was applied in a continuous treatment system (20–50 L), the photocatalytic process exhibited a high degradation efficiency, which resulted in residual microcystin-LR concentrations that were less than 1 μg L^?1 (C₀ = 5 μg L^?1).     

Using the Gasoline Additive MTBE in Forensic Environmental Investigations

A variety of additives are used in gasoline, and they can sometimes be used to help identify the source, timing, or number of gasoline spills at a site. The physicochemical characteristics of the additive MTBE, and its historical use pattern in the United States since 1979, make it a key compound to study when conducting forensic investigations of gasoline spills. MTBE's low octanol : water distribution coefficient and high solubility cause it to dissolve into groundwater more readily than other gasoline components. Thus, the initial appearance of MTBE in the groundwater is often a good indicator of a recent gasoline spill. MTBE's very low retardation and minimal biodegradation in groundwater can be used with transport rate calculations to establish relatively accurate estimates of spill timing. Because MTBE moves faster in groundwater than BTEX compounds, if a gasoline spill site has a BTEX plume that is longer than the MTBE plume, it is certain that at least two distinctly different gasoline releases have occurred. This allows for the identification of new gasoline spills, even when substantial subsurface petroleum contamination already exists. An example application is reviewed to demonstrate the use of MTBE data in forensic investigations.     

Compositional Changes of Aromatic Steroid Hydrocarbons in Naturally Weathered Oil Residues in the Egyptian Western Desert

Naturally weathered oil residues from an arid dumpsite in Al-Alamein, Egypt were analyzed for monoaromatic and triaromatic steranes to demonstrate the utility of biomarker compounds in assessing the chemical composition changes during the degradation of the released oil residues in a terrestrial environment. The characterizations of individual aromatic compounds were based on gas chromatography/mass spectrometry (GC/MS) analyses. The results showed that triaromatic sterane distributions were similar in the oil residues of varying weathering degradation extents and correlated with a fresh crude oil sample of the Western Desert-sourced oil. Molecular ratios of triaromatic sterane compounds (ratios of C₂₈20R /C₂₈20S, C₂₇20R /C₂₈20R, and C₂₈20S /[C₂₆20R + C₂₇20S ]) were proved to be suitable for source identification. Major changes in chemical compositions during weathering of the oil residues were the depletion of short chain mono- and tri-aromatic steranes in samples that had undergone extensive degradation. The results of triaromatic sterane distribution are in good agreement with weathering classification based on the analyses of saturate and aromatic hydrocarbons and the ratios of n -alkanes, PAHs and saturate biomarker compounds.     

In situ measurements of volatile aromatic hydrocarbon biodegradation rates in groundwater

Benzene and alkylbenzene biodegradation rates and patterns were measured using an in situ microcosm in a crude-oil contaminated aquifer near Bemidji, Minnesota. Benzene-D6, toluene, ethylbenzene, o-, m- and p-xylenes and four pairs of C₃- and C₄-benzenes were added to an in situ microcosm and studied over a 3-year period. The microcosm allowed for a mass-balance approach and quantification of hydrocarbon biodegradation rates within a well-defined iron-reducing zone of the anoxic plume. Among the BTEX compounds, the apparent order of persistence is ethylbenzene > benzene > m,p-xylenes > o-xylene ≥ toluene. Threshold concentrations were observed for several compounds in the in situ microcosm, below which degradation was not observed, even after hundreds of days. In addition, long lag times were observed before the onset of degradation of benzene or ethylbenzene. The isomer-specific degradation patterns were compared to observations from a multi-year study conducted using data collected from monitoring wells along a flowpath in the contaminant plume. The data were fit with both first-order and Michaelis-Menten models. First-order kinetics provided a good fit for hydrocarbons with starting concentrations below 1 mg/L and Michaelis-Menten kinetics were a better fit when starting concentrations were above 1 mg/L, as was the case for benzene. The biodegradation rate data from this study were also compared to rates from other investigations reported in the literature.     

Comparing the desorption and biodegradation of low concentrations of phenanthrene sorbed to activated carbon,biochar and compost

Carbonaceous soil amendments are applied to contaminated soils and sediments to strongly sorb hydrophobic organic contaminants (HOCs) and reduce their freely dissolved concentrations. This limits biouptake and toxicity, but also biodegradation. To investigate whether HOCs sorbed to such amendments can be degraded at all, the desorption and biodegradation of low concentrations of ¹⁴C-labelled phenanthrene (?5 μg L^?1) freshly sorbed to suspensions of the pure soil amendments activated carbon (AC), biochar (charcoal) and compost were compared. Firstly, the maximum abiotic desorption of phenanthrene from soil amendment suspensions in water, minimal salts medium (MSM) or tryptic soy broth (TSB) into a dominating silicone sink were measured. Highest fractions remained sorbed to AC (84 ± 2.3%, 87 ± 4.1%, and 53 ± 1.2% for water, MSM and TSB, respectively), followed by charcoal (35 ± 2.2%, 32 ± 1.7%, and 12 ± 0.3%, respectively) and compost (1.3 ± 0.21%, similar for all media). Secondly, the mineralization of phenanthrene sorbed to AC, charcoal and compost by Sphingomonas sp. 10-1 (DSM 12247) was determined. In contrast to the amounts desorbed, phenanthrene mineralization was similar for all the soil amendments at about 56 ± 11% of the initially applied radioactivity. Furthermore, HPLC analyses showed only minor amounts (<5%) of residual phenanthrene remaining in the suspensions, indicating almost complete biodegradation. Fitting the data to a coupled desorption and biodegradation model revealed that desorption did not limit biodegradation for any of the amendments, and that degradation could proceed due to the high numbers of bacteria and/or the production of biosurfactants or biofilms. Therefore, reduced desorption of phenanthrene from AC or charcoal did not inhibit its biodegradation, which implies that under the experimental conditions these amendments can reduce freely dissolved concentration without hindering biodegradation. In contrast, phenanthrene sorbed to compost was fully desorbed and biodegraded.     

Receptor modeling of source apportionment of Hong Kong aerosols and the implication of urban and regional contribution

Understanding the spatial–temporal variations of source apportionment of PM_2.5 is critical to the effective control of particulate pollution. In this study, two one-year studies of PM_2.5 composition were conducted at three contrasting sites in Hong Kong from November 2000 to October 2001, and from November 2004 to October 2005, respectively. A receptor model, principal component analysis (PCA) with absolute principal component scores (APCS) technique, was applied to the PM_2.5 data for the identification and quantification of pollution sources at the rural, urban and roadside sites. The receptor modeling results identified that the major sources of PM_2.5 in Hong Kong were vehicular emissions/road erosion, secondary sulfate, residual oil combustion, soil suspension and sea salt regardless of sampling sites and sampling periods. The secondary sulfate aerosols made the most significant contribution to the PM_2.5 composition at the rural (HT) (44 ± 3%, mean ± 1σ standard error) and urban (TW) (28 ± 2%) sites, followed by vehicular emission (20 ± 3% for HT and 23 ± 4% for TW) and residual oil combustion (17 ± 2% for HT and 19 ± 1% for TW). However, at the roadside site (MK), vehicular emissions especially diesel vehicle emissions were the major source of PM_2.5 composition (33 ± 1% for diesel vehicle plus 18 ± 2% for other vehicles), followed by secondary sulfate aerosols (24 ± 1%). We found that the contribution of residual oil combustion at both urban and rural sites was much higher than that at the roadside site (2 ± 0.4%), perhaps due to the marine vessel activities of the container terminal near the urban site and close distance of pathway for the marine vessels to the rural site. The large contribution of secondary sulfate aerosols at all the three sites reflected the wide influence of regional pollution. With regard to the temporal trend, the contributions of vehicular emission and secondary sulfate to PM_2.5 showed higher autumn and winter values and lower summer levels at all the sites, particularly for the background site, suggesting that the seasonal variation of source apportionment in Hong Kong was mainly affected by the synoptic meteorological conditions and the long-range transport. Analysis of annual patterns indicated that the contribution of vehicular emission at the roadside was significantly reduced from 2000/01 to 2004/05 (p < 0.05, two-tail), especially the diesel vehicular emission (p < 0.001, two-tail). This is likely attributed to the implementation of the vehicular emission control programs with the tightening of diesel fuel contents and vehicular emission standards over these years by the Hong Kong government. In contrast, the contribution of secondary sulfate was remarkably increased from 2001 to 2005 (p < 0.001, two-tail), indicating a significant growth in regional sulfate pollution over the years.     

Air–land exchanges of CO2, CH4 and N2O measured by FTIR spectrometry and micrometeorological techniques

Micrometeorological flux-gradient and nocturnal boundary layer methods were combined with Fourier transform infrared (FTIR) spectroscopy for high-precision trace gas analysis to measure fluxes of the trace gases CO₂, CH₄ and N₂O between agricultural fields and the atmosphere. The FTIR measurements were fully automated and routinely obtained a precision of 0.1–0.2% for several weeks during a measurement campaign in October 1995. In flux-gradient measurements, vertical profiles of the trace gases were measured every 30 min from the ground to 22 m. When combined with independent micrometeorological measurements of water vapour fluxes, trace gas fluxes from the underlying surface could be determined. In the nocturnal boundary layer method the rate of change in mass storage in the 0–22 m layer was combined with fluxes measured at 22 m to estimate surface fluxes. Daytime fluxes for CO₂ were −0.78±0.40 (1σ) mg CO₂ m⁻² s⁻¹. Daytime fluxes of N₂O and CH₄ were very small and difficult to measure reliably using the flux-gradient technique, despite the high precision of the concentration measurements. Mean daytime flux for N₂O was 17±48 ng N m⁻² s⁻¹, while the corresponding flux for CH₄ was 47±410 ng CH₄ m⁻² s⁻¹. The mean nighttime flux of CO₂ estimated using the nocturnal boundary layer method was +0.15±0.05 mg CO₂ m⁻² s⁻¹, in good agreement with chamber measurements of respiration rates. Nighttime fluxes of CH₄ and N₂O from the nocturnal boundary layer method were 109±69 ng CH₄ m⁻² s⁻¹ and 2±3.2 ng N m⁻² s⁻¹, respectively, in good agreement with chamber measurements and inventory estimates based on the sheep and cattle stocking rates in the region. The suitability of FTIR-based methods for long term monitoring of spatially and temporally averaged flux measurements is discussed.     

Measurement and analysis of atmospheric ammonia emissions from anaerobic lagoons

Ammonia-nitrogen flux (NH₃-N=(14/17)NH₃) was determined from six anaerobic swine waste storage and treatment lagoons (primary, secondary, and tertiary) using the dynamic chamber system. Measurements occurred during the fall of 1998 through the early spring of 1999, and each lagoon was examined for approximately one week. Analysis of flux variation was made with respect to lagoon surface water temperature (∼15 cm below the surface), lagoon water pH, total aqueous phase NH_x(=NH₃+NH₄⁺) concentration, and total Kjeldahl nitrogen (TKN). Average lagoon temperatures (across all six lagoons) ranged from approximately 10.3 to 23.3^°C. The pH ranged in value from 6.8 to 8.1. Aqueous NH_x concentration ranged from 37 to 909 mg N l⁻¹, and TKN varied from 87 to 950 mg N l⁻¹. Fluxes were the largest at the primary lagoon in Kenansville, NC (March 1999) with an average value of 120.3 μg N m⁻² min⁻¹, and smallest at the tertiary lagoon in Rocky Mount, NC (November 1998) at 40.7 μg N m⁻² min⁻¹. Emission rates were found to be correlated with both surface lagoon water temperature and aqueous NH_x concentration. The NH₃-N flux may be modeled as ln(NH₃-N flux)=1.0788+0.0406T_L+0.0015([NH_x]) (R²=0.74), where NH₃-N flux is the ammonia flux from the lagoon surface in μg N m⁻² min⁻¹, T_L is the lagoon surface water temperature in ^°C, and [NH_x] is the total ammonia-nitrogen concentration in mg N l⁻¹.     

Photocatalytic degradation kinetics and mechanism of phenobarbital in TiO2 aqueous solution

5-Ethyl-5-phenylpyrimidine-2,4,6(1H, 3H, 5H)-trione is an anti-convulsant used to treat disorders of movement, e.g. tremors. This work deals with the transformation of phenobarbital by UV/TiO₂ heterogeneous photocatalysis, to assess the decomposition of the pharmaceutical compound, to identify intermediates, as well as to elucidate some mechanistic details of the degradation. The photocatalytic removal efficiency of 100 μm phenobarbital is about 80% within 60 min, while the degradation efficiency of phenobarbital was better in alkaline solution. The study on contribution of reactive oxidative species (ROSs) has shown that OH is responsible for the major degradation of phenobarbital, while the photohole, photoelectrons and the other ROSs have the minor contribution to the degradation. Finally, based on the identification of degradation intermediates, two main photocatalytic degradation pathways have been tentatively proposed, including the hydroxylation and cleavage of pyrimidine ring in the phenobarbital molecule respectively. Certainly, the phenobarbital can be mineralized when the photocatalytic reaction time prolongs.     

Aircraft-based volatile organic compounds flux measurements with relaxed eddy accumulation

Regional estimates of fluxes of volatile organic compounds (VOCs) are required to improve our understanding of their role in the chemistry of the atmosphere. Flux measurements on such a scale can best be obtained using aircraft-based systems. These systems usually rely on the eddy covariance technique, which requires fast response gas sensors for flux measurement, but such sensors are not available for most organic compounds, therefore, the relaxed eddy-accumulation (REA) technique was selected. An aircraft-based REA sampling system was developed and used to measure isoprene emission over the boreal forest during the 1996 summer. Over a short period in July at the Boreal Ecosystem/Atmosphere Study (BOREAS) southern study area (SSA), the isoprene fluxes ranged from −0.06 to 1.79 μg m^-2 s^-1, with a mean of 0.59±0.34 μg m^-2 s^-1, while in August at the BOREAS northern study area (NSA) the isoprene fluxes ranged from 0.00 to 0.26 μg m^-2 s^-1, with a mean of 0.14±0.09 μg m^-2 s^-1. In the SSA, the isoprene fluxes over aspen ranged from 0.44 to 1.79 μg m^-2 s^-1, with a mean of 0.92±0.33 μg m^-2 s^-1, whereas over black spruce, isoprene fluxes ranged from −0.06 to 0.54 μg m^-2 s^-1, with a mean of 0.36±0.21 μg m^-2 s^-1. The isoprene fluxes were exponentially correlated with solar radiation and radiative surface temperature. High correlations between isoprene fluxes and the fluxes of CO₂ and latent heat were also observed. Carbon lost through isoprene emissions was about 0.7 and 0.8% of the CO₂ assimilation rate for aspen and black spruce, respectively. The results demonstrate that the aircraft-based relaxed eddy-accumulation technique is a promising approach for quantifying the atmosphere–surface exchange of VOCs on a regional scale.     

Definition of yearly emission factor of dust and greenhouse gases through continuous measurements in swine husbandry

The object of this study was to develop an accurate estimation method to evaluate the contribution of the various compartments of swine husbandry to dust and GHG (greenhouse gases, CO₂, CH₄ and N₂O) emission into the atmosphere during one year of observation.A weaning, a gestation, a farrowing and a fattening room in an intensive pig house were observed in three different periods (Autumn–Winter, Springtime and Summer, monitoring at least 60% of each period (20% at the beginning, in the middle and at the end) of each cycle).During monitoring, live weight, average live weight gain, number of animals and its variation, type of feed and feeding time were taken into account to evaluate their influence on PM₁₀, or the fraction of suspended particulate matter with an aerodynamic diameter less than or equal to 10 μm [Emission Inventory Guidebook, 2007. B1100 Particle Emissions from Animal Husbandry Activities. Available from: <http://reports.eea.europa.eu/EMEPCORINAIR5/en/B1100vs1.pdf> (accessed October 2008)] and to define GHG emission.The selected piggery had a ventilation control system using a free running impeller to monitor continuously real-time environmental and management parameters with an accuracy of 5%.PM₁₀ concentration was monitored by a sampler (Haz Dust EPAM 5000), either continuously or through traditional gravimetric technique, and the mean value of dust amount collected on the membranes was utilized as a correction factor to be applied to continuously collected data.PM₁₀ concentration amount incoming from inlets was removed from PM₁₀ emission calculation, to estimate the real contribution of pig house dust pollution into atmosphere.Mean yearly emission factor of PM₁₀ was measured in 2 g d^?1 LU^?1 for the weaning room, 0.09 g d^?1 LU^?1 for the farrowing room, 2.59 g d^?1 LU^?1 for the fattening room and 1.23 g d^?1 LU^?1 for the gestation room. The highest PM₁₀ concentration and emission per LU was recorded in the fattening compartment while the lowest value was recorded in the farrowing room.CO₂, CH₄ and N₂O concentrations were continuously measured in the exhaust ducts using an infrared photoacoustic detector IPD (Brüel & Kjaer, Multi-gas Monitor Type 1302, Multipoint Sampler and Doser Type 1303) sampling data every 15 min, for the 60% of the cycles.Yearly emission factor for CO₂ was measured in 5997 g d^?1 LU^?1 for the weaning room, 1278 g d^?1 LU^?1 for the farrowing room, 13,636 g d^?1 LU^?1 for the fattening room and 8851 g d^?1 LU^?1 for the gestation room.Yearly emission factor for CH₄ was measured in 24.57 g d^?1 LU^?1 for the weaning room, 4.68 g d^?1 LU^?1 for the farrowing room, 189.82 g d^?1 LU^?1 for the fattening room and 132.12 g d^?1 LU^?1 for the gestation room.Yearly emission factor for N₂O was measured in 3.62 g d^?1 LU^?1 for the weaning room, 0.66 g d^?1 LU^?1 for the farrowing room, 3.26 g d^?1 LU^?1 for the fattening room and 2.72 g d^?1 LU^?1 for the gestation room.     

Atmospheric nitrogen fluxes at the Belgian coast: 2004–2006

Daily and seasonal variations in dry and wet atmospheric nitrogen fluxes have been studied during four campaigns between 2004 and 2006 at a coastal site of the Southern North Sea at De Haan (Belgium) located at coordinates of 51.1723° N and 3.0369° E. Concentrations of inorganic N-compounds were determined in the gaseous phase, size-segregated aerosol (coarse, medium, and fine), and rainwater samples. Dissolved organic nitrogen (DON) was quantified in rainwater. The daily variations in N-fluxes of compounds were evaluated with air-mass backward trajectories, classified into the main air-masses arriving at the sampling site (i.e., continental, North Sea, and Atlantic/UK/Channel).The three, non-episodic campaigns showed broadly consistent fluxes, but during the late summer campaign exceptionally high episodic N-deposition was observed. The average dry and wet fluxes for non-episodic campaigns amounted to 2.6 and 4.0 mg N m^?2 d^?1, respectively, whereas during the episodic late summer period these fluxes were as high as 5.2 and 6.2 mg N m^?2 d^?1, respectively.Non-episodic seasons/campaigns experienced average aerosol fluxes of 0.9–1.4 mg N m^?2 d^?1. Generally, the contribution of aerosol NH₄⁺ was more significant in the medium and fine particulate fractions than that of aerosol NO₃^?, whereas the latter contributed more in the coarse fraction, especially in continental air-masses. During the dry mid-summer campaign, the DON contributed considerably (～15%) to the total N-budget.Exceptionally high episodic aerosol-N inputs have been observed for the late summer campaign, with especially high deposition rates of 3.6 and 2.9 mg N m^?2 d^?1 for Atlantic/UK/Channel and North Sea-continental (mixed) air-masses, respectively. During this pollution episode, the flux of NH₄⁺ was dominating in each aerosol fraction/air-mass, except for coarse continental aerosols. High deposition of gaseous-N was also observed in this campaign with an average total N-flux of 2–2.5-times higher than in other campaigns.     

Air pollutants in rural homes in Guizhou,China – Concentrations,speciation, and size distribution

Several types of fuels, including coal, fuel wood, and biogas, are commonly used for cooking and heating in Chinese rural households, resulting in indoor air pollution and causing severe health impacts. In this paper, we report a study monitoring multiple pollutants including PM₁₀, PM_2.5, CO, CO₂, and volatile organic compounds (VOCs) from fuel combustion at households in Guizhou province of China. The results showed that most pollutants exhibited large variability for different type of fuels except for CO₂. Among these fuels, wood combustion caused the most serious indoor air pollution, with the highest concentrations of particulate matters (218～417 μg m^?3 for PM₁₀ and 201～304 μg m^?3 for PM_2.5), and higher concentrations of CO (10.8 ± 0.8 mg m^?3) and TVOC (about 466.7 ± 337.9 μg m^?3). Coal combustion also resulted in higher concentrations of particulate matters (220～250 μg m^?3 for PM₁₀ and 170～200 μg m^?3 for PM_2.5), but different levels for CO (respectively 14.5 ± 3.7 mg m^?3 for combustion in brick stove and 5.5 ± 0.7 mg m^?3 for combustion in metal stove) and TVOC (170 mg m^?3 for combustion in brick stove and 700 mg m^?3 for combustion in metal stove). Biogas was the cleanest fuel, which brought about the similar levels of various pollutants with the indoor case of non-combustion, and worth being promoted in more areas. Analysis of the chemical profiles of PM_2.5 indicated that OC and EC were dominant components for all fuels, with the proportions of 30～48%. A high fraction of SO₄^2? (31～34%) was detected for coal combustion. The cumulative percentages of these chemical species were within the range of 0.7～1.3, which was acceptable for the assessment of mass balance.     

The use of receptor modelling and emission inventory data to explain the downward trend in UK PM10 concentrations

Statistically significant downward trends in measured UK annual mean PM₁₀ concentrations have been observed at eight out of the nine urban background monitoring sites between the start of monitoring in 1992 or 1993 and 2000.Site-specific projections of the individual components of measured PM₁₀ concentrations have been derived for the period 1992–2000 at three monitoring sites from receptor modelling results for 1999 monitoring data. Measured annual average PM₁₀ concentrations declined to between 71% and 66% of the 1992 values during this period at the sites studied. The largest contributions to the decline in total PM₁₀ are from secondary particles at London Bloomsbury (40%, 3.4 μg m⁻³, tapered element oscillating microbalance (TEOM)), stationary sources at Belfast Centre (53%, 4.6 μg m⁻³, TEOM) and roadside traffic emissions at Bury Roadside (49%, 5.0 μg m⁻³, TEOM). The good agreement between the projected total PM₁₀ concentrations and measured values for the years 1992–2000 indicate that the combination of the receptor model and the site-specific projections provide a suitably robust method for predicting future PM₁₀ concentrations and the quantification of the impact of possible future policy measures to reduce PM₁₀ concentrations. The good agreement between the projections and measured concentration also provides a useful verification of the trends in emissions inventory estimates for the 1990s.Projections of estimated PM₁₀ concentrations have also been calculated for the London Bloomsbury site for the period from 1970 to 1991. Annual mean concentrations are predicted to have been in the range from 30 to 35 μg m⁻³, TEOM from 1977 to 1991 but much higher at values between 39 and 46 μg m⁻³, TEOM in the early 1970s.     

Development of an improved optical transmission technique for black carbon (BC) analysis

A new optical transmission technique for black carbon (BC) analysis was developed to minimize interferences due to scattering effects in filter samples. A standard thermal analysis method (VDI, 1999) is used to link light attenuation by the filter samples to elemental carbon (EC) concentration. Scattering effects are minimized by immersion of the filters in oil of a similar refractive index, as is often done for microscopy purposes. Light attenuation was measured using both a white light source and a red LED of 650 nm. The usual increase in overestimation of BC concentrations with decreasing BC amount in filter samples was found considerably reduced. Some effects of BC properties (e.g. fractal dimension, microstructure and size distribution) on the specific attenuation coefficient B_ATN, however, are still present for the treated samples. B_ATN was found close to 1 m² g⁻¹ for dry-dispersed industrial BC and 7 m² g⁻¹ for nebulized BC. Good agreement was found between the oil immersion, integrating sphere and a polar photometer technique and Mie calculations. The average specific attenuation coefficient of ambient samples in oil varied between 7 and 11 m² g⁻¹ for white light and 6 and 9 m² g⁻¹ for red light (LED). B_ATN was found to have much less site variation for the treated than for the untreated samples. The oil immersion technique improved also the correlation with thermally analyzed EC. This new immersion technique therefore presents a considerable improvement over conventional optical transmission techniques and may therefore serve as a simple, fast and cost-effective alternative to thermal methods.     

Solubility of toluene,benzene and TCE in high-microbial concentration systems

We report measurements of solubility limits for benzene, toluene, and TCE in systems that contain varying levels of biomass up to 0.13 g mL⁻¹ for TCE and 0.25 g mL⁻¹ for benzene and toluene. The solubility limit increased from 21 to 48 mM when biomass (in the form of yeast) was added to aqueous batch systems containing benzene. The toluene solubility limit increased from 4.9 to greater than 20 mM. For TCE, the solubility increased from 8 mM to more than 1000 mM. Solubility for TCE (trichloroethylene) was most heavily impacted by biomass levels, changing by two orders of magnitude as the microbial concentrations approach those in biofilms.     

Hydrocarbon emission fingerprints from contemporary vehicle/engine technologies with conventional and new fuels

The present paper presents results from the analysis of 29 individual C₂–C₉ hydrocarbons (HCs) specified in the European Commission Ozone Directive. The 29 HCs are measured in exhaust from common, contemporary vehicle/engine/fuel technologies for which very little or no data is available in the literature. The obtained HC emission fingerprints are compared with fingerprints deriving from technologies that are being phased out in Europe. Based on the total of 138 emission tests, thirteen type-specific fingerprints are extracted (Mean ± SD percentage contributions from individual HCs to the total mass of the 29 HCs), essential for receptor modelling source apportionment. The different types represent exhaust from Euro3 and Euro4 light-duty (LD) diesel and petrol-vehicles, Euro3 heavy-duty (HD) diesel exhaust, and exhaust from 2-stroke preEuro, Euro1 and Euro2 mopeds. The fuels comprise liquefied petroleum gas, petrol/ethanol blends (0–85% ethanol), and mineral diesel in various blends (0–100%) with fatty acid methyl esters, rapeseed methyl esters palm oil methyl esters, soybean oil methyl or sunflower oil methyl esters. Type-specific tracer compounds (markers) are identified for the various vehicle/engine/fuel technologies.An important finding is an insignificant effect on the HC fingerprints of varying the test driving cycle, indicating that combining HC fingerprints from different emission studies for receptor modelling purposes would be a robust approach.The obtained results are discussed in the context of atmospheric ozone formation and health implications from emissions (mg km^?1 for LD and mopeds and mg kW h^?1 for HD, all normalised to fuel consumption: mg dm^?3 fuel) of the harmful HCs, benzene and 1,3-butadiene.Another important finding is a strong linear correlation of the regulated “total” hydrocarbon emissions (tot-HC) with the ozone formation potential of the 29 HCs (ΣPO₃ = (1.66 ± 0.04) × tot-RH; r² = 0.93). Tot-HC is routinely monitored in emission control laboratories, whereas C₂–C₉ are not. The revealed strong correlations broadens the usability of data from vehicle emission control laboratories and facilitates the comparison of the ozone formation potential of HCs in exhaust from of old and new vehicle/engine/fuel technologies.     

Trace gas variations at Cape Point,South Africa,during May 1997 following a regional biomass burning episode

During the continuous monitoring of atmospheric parameters at the station Cape Point (34°S, 18°E), a smoke plume originating from a controlled fire of 30-yr-old fynbos was observed on 6 May 1997. For this episode, which was associated with a nocturnal inversion and offshore airflow, atmospheric parameters (solar radiation and meteorological data) were considered and the levels of various trace gases compared with those measured at Cape Point in maritime air. Concentration maxima in the morning of 6 May for CO₂, CO, CH₄ and O₃ amounted to 370.3 ppm, 491 ppb, 1730 ppb and 47 ppb, respectively, whilst the mixing ratios of several halocarbons (F-11, F-12, F-113, CCl₄ and CH₃CCl₃) remained at background levels. In the case of CO, the maritime background level for this period was exceeded by a factor of 9.8. Differences in ozone levels of up to 5 ppb between air intakes at 4 and 30 m above the station (located at 230 m above sea level) indicated stratification of the air advected to Cape Point during the plume event. Aerosols within the smoke plume caused the signal of global solar radiation and UV–A to be attenuated from 52.4 to 13.0 mW cm⁻² and from 2.3 to 1.3 mW cm⁻², respectively, 5 h after the trace gases had reached their maxima. Emission ratios (ERs) calculated for CO and CH₄ relative to CO₂ mixing ratios amounted to 0.042 and 0.0040, respectively, representing one of the first results for fires involving fynbos. The CO ER is somewhat lower than those given in the literature for African savanna fires (average ER=0.048), whilst for CH₄ the ER falls within the range of ERs reported for the flaming (0.0030) and smouldering phases (0.0055) of savanna fires. Non-methane hydrocarbon (NMHC) data obtained from a grab sample collected during the plume event were compared to background levels. The highest ERs (ΔNMHC/ΔCH₄) have been obtained for the C₂–C₃ hydrocarbons (e.g. ethene at 229.3 ppt ppb⁻¹), whilst the C₄–C₇ hydrocarbons were characterised by the lowest ERs (e.g. n-hexane at 1.0 and n-pentane at 0.8 ppt ppb⁻¹).     

Field performance of dichotomous sequential PM air samplers

For over one year, the Environmental Protection Commission of Hillsborough County (EPCHC) in Tampa, Florida, operated two dichotomous sequential particulate matter air samplers collocated with a manual Federal Reference Method (FRM) air sampler at a waterfront site on Tampa Bay. The FRM was alternately configured as a PM_2.5, then as a PM₁₀ sampler. For the dichotomous sampler measurements, daily 24-h integrated PM_2.5 and PM_10–2.5 ambient air samples were collected at a total flow rate of 16.7 l min⁻¹. A virtual impactor split the air into flow rates of 1.67 and 15.0 l min⁻¹ onto PM_10–2.5 and PM_2.5 47-mm diameter PTFE^® filters, respectively. Between the two dichotomous air samplers, the average concentration, relative bias and relative precision were 13.3 μg m⁻³, 0.02% and 5.2% for PM_2.5 concentrations (n=282), and 12.3 μg m⁻³, 3.9% and 7.7% for PM_10–2.5 concentrations (n=282). FRM measurements were alternate day 24-h integrated PM_2.5 or PM₁₀ ambient air samples collected onto 47-mm diameter PTFE^® filters at a flow rate of 16.7 l min⁻¹. Between a dichotomous and a PM_2.5 FRM air sampler, the average concentration, relative bias and relative precision were 12.4 μg m⁻³, −5.6% and 8.2% (n=43); and between a dichotomous and a PM₁₀ FRM air sampler, the average concentration, relative bias and relative precision were 25.7 μg m⁻³, −4.0% and 5.8% (n=102). The PM_2.5 concentration measurement standard errors were 0.95, 0.79 and 1.02 μg m⁻³; for PM₁₀ the standard errors were 1.06, 1.59, and 1.70 μg m⁻³ for two dichotomous and one FRM samplers, respectively, which indicate the dichotomous samplers have superior technical merit. These results reveal the potential for the dichotomous sequential air sampler to replace the combination of the PM_2.5 and PM₁₀ FRM air samplers, offering the capability of making simultaneous, self-consistent determinations of these particulate matter fractions in a routine ambient monitoring mode.     

Kinetics of the gas-phase reactions of NO3 radicals with ethyl acrylate,n-butyl acrylate,methyl methacrylate and ethyl methacrylate

The relative rate method has been used to determine the rate constants for the gas-phase reactions of NO₃ radicals with a series of acrylate esters: ethyl acrylate (k₁), n-butyl acrylate (k₂), methyl methacrylate (k₃) and ethyl methacrylate (k₄) at 298 ± 1 K and 760 Torr. The obtained rate constants are k₁ = (1.8 ± 0.25) × 10^?16 cm³ molecule^?1 s^?1, k₂ = (2.1 ± 0.33) × 10^?16 cm³ molecule^?1 s^?1, k₃ = (3.6 ± 1.2) × 10^?15 cm³ molecule^?1 s^?1, k₄ = (4.9 ± 1.7) × 10^?15 cm³ molecule^?1 s^?1. The experimental rate constants are in good agreement with theoretical rate constants calculated by an algorithm of the correlation between the rate constants and the orbital energies for the reactions of unsaturated VOCs with NO₃ radicals. In addition, the atmospheric lifetimes of the compound against NO₃ attack are estimated and the results show that NO₃ reactions contribute little to the atmospheric losses of acrylate esters except in polluted regions.