Using biochar for remediation of soils contaminated with heavy metals and organic pollutants

Soil contamination with heavy metals and organic pollutants has increasingly become a serious global environmental issue in recent years. Considerable efforts have been made to remediate contaminated soils. Biochar has a large surface area, and high capacity to adsorb heavy metals and organic pollutants. Biochar can potentially be used to reduce the bioavailability and leachability of heavy metals and organic pollutants in soils through adsorption and other physicochemical reactions. Biochar is typically an alkaline material which can increase soil pH and contribute to stabilization of heavy metals. Application of biochar for remediation of contaminated soils may provide a new solution to the soil pollution problem. This paper provides an overview on the impact of biochar on the environmental fate and mobility of heavy metals and organic pollutants in contaminated soils and its implication for remediation of contaminated soils. Further research directions are identified to ensure a safe and sustainable use of biochar as a soil amendment for remediation of contaminated soils.     

Dispersal networks for enhancing bacterial degradation in heterogeneous environments

Successful biodegradation of organic soil pollutants depends on their bioavailability to catabolically active microorganisms. In particular, environmental heterogeneities often limit bacterial access to pollutants. Experimental and modelling studies revealed that fungal networks can facilitate bacterial dispersal and may thereby improve pollutant bioavailability. Here, we investigate the influence of such bacterial dispersal networks on biodegradation performance under spatially heterogeneous abiotic conditions using a process-based simulation model. To match typical situations in polluted soils, two types of abiotic conditions are studied: heterogeneous bacterial dispersal conditions and heterogeneous initial resource distributions. The model predicts that networks facilitating bacterial dispersal can enhance biodegradation performance for a wide range of these conditions. Additionally, the time horizon over which this performance is assessed and the network’s spatial configuration are key factors determining the degree of biodegradation improvement. Our results support the idea of stimulating the establishment of fungal mycelia for enhanced bioremediation of polluted soils.     

Biological remediation of explosives and related nitroaromatic compounds

Nitroaromatics form an important group of recalcitrant xenobiotics. Only few aromatic compounds, bearing one nitro group as a substituent of the aromatic ring, are produced as secondary metabolites by microorganisms. The majority of nitroaromatic compounds in the biosphere are industrial chemicals such as explosives, dyes, polyurethane foams, herbicides, insecticides and solvents. These compounds are generally recalcitrant to biological treatment and remain in the biosphere, where they constitute a source of pollution due to both toxic and mutagenic effects on humans, fish, algae and microorganisms. However, relatively few microorganisms have been described as being able to use nitroaromatic compounds as nitrogen and/or carbon and energy source. The best-known nitroaromatic compound is the explosive TNT (2,4,6-trinitrotoluene). This article reviews the bioremediation strategies for TNT-contaminated soil and water. It comes to the following conclusion: The optimal remediation strategy for nitroaromatic compounds depends on many site-specific factors. Composting and the use of reactor systems lend themselves to treating soils contaminated with high levels of explosives (e.g. at former ammunition production facilities, where areas with a high contamination level are common). Compared to composting systems, bioreactors have the major advantage of a short treatment time, but the disadvantage of being more labour intensive and more expensive. Studies indicate that biological treatment systems, which are based on the activity of the fungus Phanerochaete chrysosporium or on Pseudomonas sp. ST53, might be used as effective methods for the remediation of highly contaminated soil and water. Phytoremediation, although not widely used now, has the potential to become an important strategy for the remediation of soil and water contaminated with explosives. It is best suited where contaminant levels are low (e.g. at military sites where pollution is rather diffuse) and where larger contaminated surfaces or volumes have to be treated. In addition, phytoremediation can be used as a polishing method after other remediation treatments, such as composting or bioslurry, have taken place. This in-situ treatment method has the advantage of lower treatment costs, but has the disadvantage of a considerable longer treatment time. In order to improve the cost-efficiency, phytoremediation of nitroaromatics (and other organic xenobiotics) could be combined with bio-energy production. This requires, however, detailed knowledge on the fate of the contaminants in the plants as well as the development of efficient treatment methods for the contaminated biomass that minimise the spreading of the contaminants into the environment during post harvest treatment.     

Utilising the Synergy between Plants and Rhizosphere Microorganisms to Enhance Breakdown of Organic Pollutants in the Environment (15 pp)

Background Phytoremediation is a promising technology for the cleanup of polluted environments. The technology has so far been used mainly to remove toxic heavy metals from contaminated soil, but there is a growing interest in broadening its applications to remove/degrade organic pollutants in the environment. Both plants and soil microorganisms have certain limitations with respect to their individual abilities to remove/breakdown organic compounds. A synergistic action by both rhizosphere microorganisms that leads to increased availability of hydrophobic compounds, and plants that leads to their removal and/or degradation, may overcome many of the limitations, and thus provide a useful basis for enhancing remediation of contaminated environments.Main Features The review of literature presented in this article provides an insight to the nature of plant-microbial interactions in the rhizosphere, with a focus on those processes that are relevant to the breakdown and/or removal of organic pollutants. Due consideration has been given to identify opportunities for utilising the plant-microbial synergy in the rhizosphere to enhance remediation of contaminated environments.Results and Discussion The literature review has highlighted the existence of a synergistic interaction between plants and microbial communities in the rhizosphere. This interaction benefits both microorganisms through provision of nutrients by root exudates, and plants through enhanced nutrient uptake and reduced toxicity of soil contaminants. The ability of the plant-microbial interaction to tackle some of the most recalcitrant organic chemicals is of particular interest with regard to enhancing and extending the scope of remediation technologies.Conclusions Plant-microbial interactions in the rhizosphere offer very useful means for remediating environments contaminated with recalcitrant organic compounds.Outlook A better knowledge of plant-microbial interactions will provide a basis for improving the efficacy of biological remediations. Further research is, however, needed to investigate different feedback mechanisms that select and regulate microbial activity in the rhizosphere.     

COP-compost: a software to study the degradation of organic pollutants in composts

Composting has been demonstrated to be effective in degrading organic pollutants (OP) whose behaviour depends on the composting conditions, the microbial populations activated and interactions with organic matters. The fate of OP during composting involves complex mechanisms and models can be helpful tools for educational and scientific purposes, as well as for industrialists who want to optimise the composting process for OP elimination. A COP-Compost model, which couples an organic carbon (OC) module and an organic pollutant (OP) module and which simulates the changes of organic matter, organic pollutants and the microbial activities during the composting process, has been proposed and calibrated for a first set of OP in a previous study. The objectives of the present work were (1) to introduce the COP-Compost model from its convenient interface to a potential panel of users, (2) to show the variety of OP that could be simulated, including the possibility of choosing between degradation through co-metabolism or specific metabolism and (3) to show the effect of the initial characteristics of organic matter quality and its microbial biomass on the simulated results of the OP dynamic. In the model, we assumed that the pollutants can be adsorbed on organic matter according to the biochemical quality of the OC and that the microorganisms can degrade the pollutants at the same time as they degrade OC (by co-metabolism). A composting experiment describing two different ¹⁴C-labelled organic pollutants, simazine and pyrene, were chosen from the literature because the four OP fractions simulated in the model were measured during the study (the mineralised, soluble, sorbed and non-extractable fractions). Except for the mineralised fraction of simazine, a good agreement was achieved between the simulated and experimental results describing the evolution of the different organic fractions. For simazine, a specific biomass had to be added. To assess the relative importance of organic matter dynamics on the organic pollutants’ behaviour, a sensitivity analysis was conducted. The sensitivity analysis demonstrated that the parameters associated with organic matter dynamics and its initial microbial biomass greatly influenced the evolution of all the OP fractions, although the initial biochemical quality of the OC did not have a significant impact on the OP evolution.     

Sterilization affects soil organic matter chemistry and bioaccumulation of spiked p,p′-DDE and anthracene by earthworms

Laboratory experiments were conducted to assess the effects of soil sterilization on the bioavailability of spiked p,p′-DDE and anthracene to the earthworms Eisenia fetida and Lumbricus terrestris. Physical and chemical changes to soil organic matter (SOM) induced by sterilization were also studied. Uptake of both compounds added after soil was autoclaved or gamma irradiated increased for E. fetida. Sterilization had no effect on bioaccumulation of p,p′-DDE by L. terrestris, and anthracene uptake increased only in gamma-irradiated soils. Analyses by FT-IR and DSC indicate sterilization alters SOM chemistry and may reduce pollutant sorption. Chemical changes to SOM were tentatively linked to changes in bioaccumulation, although the effects were compound and species specific. Artifacts produced by sterilization could lead to inaccurate risk assessments of contaminated sites if assumptions derived from studies carried out in sterilized soil are used. Ultimately, knowledge of SOM chemistry could aid predictions of bioaccumulation of organic pollutants.     

Removal of organic contaminants in bioretention medium amended with activated carbon from sewage sludge

Bioretention, also known as rain garden, allows stormwater to soak into the ground through a soil-based medium, leading to removal of particulate and dissolved pollutants and reduced peak flows. Although soil organic matter (SOM) is efficient at sorbing many pollutants, amending the bioretention medium with highly effective adsorbents has been proposed to optimize pollutant removal and extend bioretention lifetime. The aim of this research was to investigate whether soil amended with activated carbon produced from sewage sludge increases the efficiency to remove hydrophobic organic compounds frequently detected in stormwater, compared to non-amended soil. Three lab-scale columns (520 cm³) were packed with soil (bulk density 1.22 g/cm³); activated carbon (0.5% w/w) was added to two of the columns. During 28 days, synthetic stormwater—ultrapure water spiked with seven hydrophobic organic pollutants and dissolved organic matter in the form of humic acids—was passed through the column beds using upward flow (45 mm/h). Pollutant concentrations in effluent water (collected every 12 h) and polluted soils, as well as desorbed amounts of pollutants from soils were determined using GC-MS. Compared to SOM, the activated carbon exhibited a significantly higher adsorption capacity for tested pollutants. The amended soil was most efficient for removing moderately hydrophobic compounds (log K _ow 4.0–4.4): as little as 0.5% (w/w), carbon addition may extend bioretention medium lifetime by approximately 10–20 years before saturation of these pollutants occurs. The column tests also indicated that released SOM sorb onto activated carbon, which may lead to early saturation of sorption sites on the carbon surface. The desorption test revealed that the pollutants are generally strongly sorbed to the soil particles, indicating low bioavailability and limited biodegradation.

     

Soil sterilization affects aging-related sequestration and bioavailability of p,p′-DDE and anthracene to earthworms

Laboratory experiments investigated the effects of soil sterilization and compound aging on the bioaccumulation of spiked p,p′-DDE and anthracene by Eisenia fetida and Lumbricus terrestris. Declines in bioavailability occurred as pollutant residence time in both sterile and non-sterile soils increased from 3 to 203 d. Accumulation was generally higher in sterile soils during initial periods of aging (from 3-103 d). By 203 d, however, bioavailability of the compounds was unaffected by sterilization. Gamma irradiation and autoclaving may have altered bioavailability by inducing changes in the chemistry of soil organic matter (SOM). The results support a dual-mode partitioning sorption model in which the SOM components associated with short-term sorption (the ‘soft’ or ‘rubbery’ phases) are more affected than are the components associated with long-term sorption (the ‘glassy’ or microcrystalline phases). Risk assessments based on data from experiments in which sterile soil was used could overestimate exposure and bioaccumulation of pollutants.     

Microbial bioavailability of pyrene in three laboratory-contaminated soils under aerobic and anaerobic conditions

Changes in bioavailability of pyrene in three uncontaminated soils were examined under aerobic and anaerobic conditions. Three soils were aerobically aged with pyrene and [(14)C]pyrene for 63 days, then incubated with water, nitrate, or sulfate under aerobic or anaerobic conditions for one year. Under aerobic conditions, microorganisms in two soils mineralized 58-82% of the added [(14)C]pyrene. The two soils amended with nitrate were seen to have enhanced aerobic mineralization rates. In one of these soils, non-extractable pyrene was seen to decrease over the course of the study due to desorption and mineralization, nitrate amendment enhanced this effect. Under anaerobic conditions, generated with a N(2):CO(2)(g) headspace, two soils with nitrate or sulfate amendment showed an increase in extractable [(14)C]pyrene at 365 days relative to inhibited controls, presumably due to microbially mediated oxidation-reduction potential and pH alteration of the soil environment. These observations in different soils incubated under aerobic and anaerobic conditions have important implications relative to the impact of microbial electron acceptors on bioavailability and transport of non-polar organic compounds in the environment suggesting that, given enough time, under the appropriate environmental conditions, non-extractable material becomes bioavailable. This information should be considered when assessing site specific exposure risks at PAH contaminated locations.     

堆肥技术处理有机污染土壤的研究进展

堆肥化处理是一种新型、高效的生物修复技术 ,本文综述了国内外应用堆肥技术处理有机污染土壤的研究进展 ,总结了对有机污染土壤进行堆肥处理的主要影响因素。本文还指出了堆肥技术目前存在的问题 ,并对其发展前景进行了展望     

Plant aided bioremediation in the vadose zone: model development and applications

Phytoremediation has the potential to enhance clean up of land contaminated by various pollutants. A mathematical model that includes a two-fluid phase flow model of water flow as well as a two-region soil model of contaminant reactions was developed and applied to various bioremediation scenarios in the unsaturated zone, especially to plant-aided bioremediation. To investigate model behavior and determine the main parameters and mechanisms that affect bioremediation in unplanted and planted soils, numerical simulations of theoretical scenarios were conducted before applying the model to field data. It is observed from the results that parameters affecting the contaminant concentration in the water phase, such as aqueous solubility, the octanol-water partition coefficient, and organic carbon content of the soil controlled the contaminant fate in the vadose zone. Simulation using the developed model also characterized the fate and transport of the contaminants both in planted and unplanted soils satisfactorily for field applications. Although phytoremediation has the potential for remediation of contaminated soils, results from both modeling and field studies suggested that plants may not always enhance the remediation efficiency when the soil already has a high microbial concentration, when the contaminant bioavailability is low, or when the overall reaction is mass transfer-limited. Therefore, other steps to increase contaminant bioavailability are needed in phytoremediation applications; natural purification mechanisms such as aging, volatilization, and natural bioremediation should be considered to maximize the plant effect and minimize the cost.     

Phytoremediation of polyaromatic hydrocarbons, anilines and phenols

Phytoremediation technologies based on the combined action of plants and the microbial communities that they support within the rhizosphere hold promise in the remediation of land and waterways contaminated with hydrocarbons but they have not yet been adopted in large-scale remediation strategies. In this review plant and microbial degradative capacities, viewed as a continuum, have been dissected in order to identify where bottle-necks and limitations exist. Phenols, anilines and polyaromatic hydrocarbons (PAHs) were selected as the target classes of molecule for consideration, in part because of their common patterns of distribution, but also because of the urgent need to develop techniques to overcome their toxicity to human health. Depending on the chemical and physical properties of the pollutant, the emerging picture suggests that plants will draw pollutants including PAHs into the plant rhizosphere to varying extents via the transpiration stream. Mycorrhizosphere-bacteria and -fungi may play a crucial role in establishing plants in degraded ecosystems. Within the rhizosphere, microbial degradative activities prevail in order to extract energy and carbon skeletons from the pollutants for microbial cell growth. There has been little systematic analysis of the changing dynamics of pollutant degradation within the rhizosphere; however, the importance of plants in supplying oxygen and nutrients to the rhizosphere via fine roots, and of the beneficial effect of microorganisms on plant root growth is stressed. In addition to their role in supporting rhizospheric degradative activities, plants may possess a limited capacity to transport some of the more mobile pollutants into roots and shoots via fine roots. In those situations where uptake does occur (i.e. only limited microbial activity in the rhizosphere) there is good evidence that the pollutant may be metabolised. However, plant uptake is frequently associated with the inhibition of plant growth and an increasing tendency to oxidant stress. Pollutant tolerance seems to correlate with the ability to deposit large quantities of pollutant metabolites in the 'bound' residue fraction of plant cell walls compared to the vacuole. In this regard, particular attention is paid to the activities of peroxidases, laccases, cytochromes P450, glucosyltransferases and ABC transporters. However, despite the seemingly large diversity of these proteins, direct proof of their participation in the metabolism of industrial aromatic pollutants is surprisingly scarce and little is known about their control in the overall metabolic scheme. Little is known about the bioavailability of bound metabolites; however, there may be a need to prevent their movement into wildlife food chains. In this regard, the application to harvested plants of composting techniques based on the degradative capacity of white-rot fungi merits attention.     

Modelling the extraction of soil contaminants with supercritical carbon dioxide

Extractions of volatile organic compounds (VOC’s) in contaminated soil from petroleum site were performed with supercritical carbon dioxide at different temperatures, pressures, extraction times, solvent flow rates, soil moisture contents and soil acidity. Three soil systems were investigated in order to compare the best parameters for extraction. A central composite rotatable design has been used to evaluate the influence of operation conditions on the extraction efficiency to generate model equations representing the types of soil. The results indicate that at least 70-80% of the initial amount of VOC’s can be removed at moderate temperatures even at very high moisture content. Supercritical extraction is best suited to silt type soils which have a low adsorption capacity. VOC’s recoveries from the artificial contaminated soil samples were higher in comparison with real contaminated soils. At moderate temperatures, the extraction efficiency for real soils is low because pollutants bind strongly to the soil.     

Hydroxypropyl-β-cyclodextrin extractability and bioavailability of phenanthrene in humin and humic acid fractions from different soils and sediments

Organic matter (OM) plays a vital role in controlling polycyclic aromatic hydrocarbon (PAH) bioavailability in soils and sediments. In this study, both a hydroxypropyl-β-cyclodextrin (HPCD) extraction test and a biodegradation test were performed to evaluate the bioavailability of phenanthrene in seven different bulk soil/sediment samples and two OM components (humin fractions and humic acid (HA) fractions) separated from these soils/sediments. Results showed that both the extent of HPCD-extractable phenanthrene and the extent of biodegradable phenanthrene in humin fraction were lower than those in the respective HA fraction and source soil/sediment, demonstrating the limited bioavailability of phenanthrene in the humin fraction. For the source soils/sediments and the humin fractions, significant inverse relationships were observed between the sorption capacities for phenanthrene and the amounts of HPCD-extractable or biodegradable phenanthrene (p?<?0.05), suggesting the importance of the sorption capacity in affecting desorption and biodegradation of phenanthrene. Strong linear relationships were observed between the amount of HPCD-extractable phenanthrene and the amount degraded in both the bulk soils/sediments and the humin fractions, with both slopes close to 1. On the other hand, in the case of phenanthrene contained in HA, a poor relationship was observed between the amount of phenanthrene extracted by HPCD and the amount degraded, with the former being much less than the latter. The results revealed the importance of humin fraction in affecting the bioavailability of phenanthrene in the bulk soils/sediments, which would deepen our understanding of the organic matter fractions in affecting desorption and biodegradation of organic pollutants and provide theoretical support for remediation and risk assessment of contaminated soils and sediments.     

The application of the vermicomposting process in the bioremediation of diesel contaminated soils

Abstract

Polycyclic Aromatic Hydrocarbons (PAHs) are among the environmental pollutants that have very high carcinogenic and mutagenic activity. Among hundreds of different PAHs, 17 are considered priority pollutants and routinely monitored for regulatory purposes. Extended periods of exposure and expensive clean-up costs are typically associated with the vast majority of processes used for the remediation of areas contaminated with PAHs. The results of this study indicate that bioremediation via vermicomposting could be an effective method for remedying soils contaminated with toxic organic compounds, such as PAHs. This study was conducted over 90?days in the presence of various quantities of organic matter (cattle manure) to recover soils contaminated with PAHs. High-performance liquid chromatography (HPLC) was applied to identify PAHs. An evaluation of the toxicity of the final material and the transformation of the organic matter throughout the process was also conducted. The data presented here suggest a relationship between the molar mass of the PAHs and the ability of the vermicomposting process to promote biodegradation. These results suggest that vermicomposting has great potential to be utilized as a tool for the bioremediation of soils impacted by PAHs.     

Correlations between PAH bioavailability,degrading bacteria,and soil characteristics during PAH biodegradation in five diffusely contaminated dissimilar soils

The natural biodegradation of seven polycyclic aromatic hydrocarbons (PAHs) by native microorganisms was studied in five soils from Normandy (France) from diffusely polluted areas, which can also pose a problem in terms of surfaces and amounts of contaminated soils. Bioavailability tests using cyclodextrin-based extractions were performed. The natural degradation of low molecular weight (LMW) PAHs was not strongly correlated to their bioavailability due to their sorption to geosorbents. Conversely, the very low degradation of high molecular weight (HMW) PAHs was partly correlated to their poor availability, due to their sorption on complexes of organic matter and kaolinites or smectites. A principal component analysis allowed us to distinguish between the respective degradation behaviors of LMW and HMW PAHs. LMW PAHs were degraded in less than 2–3 months and were strongly influenced by the relative percentage of phenanthrene-degrading bacteria over total bacteria in soils. HMW PAHs were not significantly degraded, not only because they were less bioavailable but also because of a lack of degrading microorganisms. Benzo[a]pyrene stood apart since it was partly degraded in acidic soils, probably because of a catabolic cooperation between bacteria and fungi.     

Bioremediation of a weathered and a recently oil-contaminated soils from Brazil: a comparison study

The facility with which hydrocarbons can be removed from soils varies inversely with aging of soil samples as a result of weathering. Weathering refers to the result of biological, chemical and physical processes that can affect the type of hydrocarbons that remain in a soil. These processes enhance the sorption of hydrophobic organic contaminants (HOCs) to the soil matrix, decreasing the rate and extent of biodegradation. Additionally, pollutant compounds in high concentrations can more easily affect the microbial population of a recently contaminated soil than in a weathered one, leading to inhibition of the biodegradation process. The present work aimed at comparing the biodegradation efficiencies obtained in a recently oil-contaminated soil (spiked one) from Brazil and an weathered one, contaminated for four years, after the application of bioaugmentation and biostimulation techniques. Both soils were contaminated with 5.4% of total petroleum hydrocarbons (TPHs) and the highest biodegradation efficiency (7.4%) was reached for the weathered contaminated soil. It could be concluded that the low biodegradation efficiencies reached for all conditions tested reflect the treatment difficulty of a weathered soil contaminated with a high crude oil concentration. Moreover, both soils (weathered and recently contaminated) submitted to bioaugmentation and biostimulation techniques presented biodegradation efficiencies approximately twice as higher as the ones without the aforementioned treatment (natural attenuation).     

Mobilization of phenol and dichlorophenol in unsaturated soils by non-uniform electrokinetics

The poor mobility of organic pollutants in contaminated sites frequently results in slow remediation processes. Organics, especially hydrophobic compounds, are generally retained strongly in soil matrix as a result of sorption, sequestration, or even formation into non-aqueous-phase liquids and their mobility is thus greatly reduced. The objective of this study was to evaluate the feasibility of using non-uniform electrokinetic transport processes to enhance the mobility of organic pollutants in unsaturated soils with no injection reagents. Phenol and 2,4-dichlorophenol (2,4-DCP), and kaolin and a natural sandy loam soil were selected as model organics and soils, respectively. The results showed that non-uniform electrokinetics can accelerate the desorption and movement of phenol and 2,4-DCP in unsaturated soils. Electromigration and electroosmotic flow were the main driving forces, and their role in the mobilization of phenol and 2,4-DCP varied with soil pH. The movement of 2,4-DCP in the sandy loam towards the anode (about 1.0 cmd(-1)V(-1)) was 1.0-1.5 cmd(-1)V(-1) slower than that in the kaolin soil, but about 0.5 cmd(-1)V(-1) greater than that of phenol in the sandy loam. When the sandy loam was adjusted to pH 9.3, the movement of phenol and 2,4-DCP towards the anode was about twice and five times faster than that at pH 7.7, respectively. The results also demonstrated that the movement of phenol and 2,4-DCP in soils can be easily controlled by regulating the operational mode of electric field. It is believed that non-uniform electrokinetics has the potential for practical application to in situ remediation of organics-contaminated sites.     

Identifying sources of soil inorganic pollutants on a regional scale using a multivariate statistical approach: role of pollutant migration and soil physicochemical properties

Principal components analysis (PCA) and correlation analysis were used to estimate the contribution of four components related to pollutant sources on the total variation in concentrations of Cu, Zn, Pb, Cd, As, Se, Hg, Fe and Mn in surface soil samples from a valley in east China with numerous copper and zinc smelters. Results indicate that when carrying out source identification of inorganic pollutants their tendency to migrate in soils may result in differences between the pollutant composition of the source and the receptor soil, potentially leading to errors in the characterization of pollutants using multivariate statistics. The stability and potential migration or movement of pollutants in soils must therefore be taken into account. Soil physicochemical properties may offer additional useful information. Two different mechanisms have been hypothesized for correlations between soil heavy metal concentrations and soil organic matter content and these may be helpful in interpreting the statistical analysis.     

Phytoremediation to increase the degradation of PCBs and PCDD/Fs

Phytoremediation is already regarded as an efficient technique to remove or degrade various pollutants in soils, water and sediments. However, hydrophobic organic molecules such as PAHs, PCBs and PCDD/Fs are much less responsive to bioremediation strategies than, for example, BTEX or LAS. PCDD/Fs and PCBs represent 3 prominent groups of persistent organic pollutants that share common chemical, toxicological and environmental properties. Their widespread presence in the environment may be explained by their chemical and biological stability. This review considers their fate and dissipation mechanisms. It is then possible to identify major sinks and to understand biological activities useful for remediation. Public health and economic priorities lead to the conclusion that alternative techniques to physical treatments are required. This review focuses on particular problems encountered in biodegradation and bioavailability of PCDD/Fs and PCBs. It highlights the potential and limitations of plants and micro-organisms as bioremediation agents and summarises how plants can be used to augment bacterial activity. Phytoremediation is shown to provide some new possibilities in reducing risks associated with dioxins and PCBs.