生活垃圾恶臭污染释放过程研究

在实验室模拟填埋条件下,考察了不同垃圾组分、含水率、温度、填埋高度和压实密度对生活垃圾恶臭释放的影响。结果表明:生活垃圾恶臭物质主要来源于厨余垃圾、果皮垃圾和生活垃圾;含水率越高,恶臭物质释放越多;温度越高,恶臭物质释放越多;适当增加填埋高度不仅可以减少填埋作业面积,还可减少恶臭物质释放;提高生活垃圾的压实密度,可在增大恶臭气体迁移阻力、减轻恶臭污染的同时,增强垃圾堆体的稳定性,一定程度上增加了填埋库容。     

城市生活垃圾渗透系数测试研究

采用常水头测渗实验,对不同压实密度和水力梯度下的新鲜垃圾与陈垃圾的渗透系数进行测试,根据达西定律求得渗透系数值。由于垃圾的不均匀性、小颗粒的运动和大孔隙沟道流的形成和改变,实验初始阶段渗透系数值先增大至峰值,然后缓慢降低直至趋于稳定。实验稳定后,新鲜垃圾压实密度为0.75~0.95 t/m3时,渗透系数值约为1.26E-03~1.43E-03 cm/s。陈垃圾在压实密度分别为1.2和1.4 t/m3时,渗透系数为8.29E-04和1.35E-04 cm/s。     

厌氧陈腐垃圾模拟柱对渗滤液COD和NH_3-N的处理特性

通过实地钻取阿苏卫填埋场陈腐垃圾,真实模拟填埋场压实工艺,制作2种不同压实密度的陈腐垃圾模拟柱,对比研究其对渗滤液COD、NH3-N处理效果。结果表明,当模拟柱压实密度为1.09 t/m3时,渗滤液垂直运动明显;回灌此模拟柱水力负荷分别为18.6、28、37.2和46.5 L/t时,COD去除效果稳定,平均去除率达82.4%,最高去除率可达90.1%;出水NH3-N浓度均值为549.3 mg/L,且介于415～700 mg/L间变化。自循环回灌COD去除率最高仅为11.5%,NH3-N去除率最高仅为11.8%,两者去除效果不明显。因此,北方平原型填埋场进一步完善填埋工艺,使填埋场垂直方向渗透系数分布均匀,充分利用陈腐垃圾堆体的自降解能力,才是处理渗滤液污染的关键。     

厌氧陈腐垃圾模拟柱对渗滤液COD和NH_3-N的处理特性

通过实地钻取阿苏卫填埋场陈腐垃圾,真实模拟填埋场压实工艺,制作2种不同压实密度的陈腐垃圾模拟柱,对比研究其对渗滤液COD、NH3-N处理效果。结果表明,当模拟柱压实密度为1.09 t/m3时,渗滤液垂直运动明显;回灌此模拟柱水力负荷分别为18.6、28、37.2和46.5 L/t时,COD去除效果稳定,平均去除率达82...     

城市生活垃圾渗透系数测试研究

采用常水头测渗实验，对不同压实密度和水力梯度下的新鲜垃圾与陈垃圾的渗透系数进行测试，根据达西定律求得渗透系数值。由于垃圾的不均匀性、小颗粒的运动和大孔隙沟道流的形成和改变，实验初始阶段渗透系数值先增大至峰值，然后缓慢降低直至趋于稳定。实验稳定后，新鲜垃圾压实密度为0．75—0．95t／m^3时，渗透系数值约为1．26E-03～1．43E-03cm／s。陈垃圾在压实密度分别为1．2和1．4t／m^3时，渗透系数为8．29E-04和1．35E-04cm／s。     

城市固体废弃物持水率的室内实验研究

垃圾土持水率是估算填埋场淋沥液高度和分析填埋体稳定性的重要参数。通过对高压固结仪的改造,研制垃圾土持水率的室内实验仪器,并在该仪器上对取自我国南方某填埋场3个不同深度的大直径垃圾土试样进行各级荷载下的持水率实验。研究结果表明,随填埋深度增大,垃圾年份增加,垃圾土可降解度降低,腐殖质含量增大,垃圾土的持水率减小;随上覆压力增大,干重和湿重持水率减小,当上覆压力增大到一定程度,减小趋势变缓;随上覆压力的增大,体积持水率一般呈减小的趋势,但对于疏松垃圾土,在较小的压力下,体积持水率有增大的趋势,当压力增大到一定程度,则随压力的增大而减小;随干密度的增大,垃圾土干重和湿重持水率均减小。提出的垃圾土持水率的室内实验方法和研制的仪器合理可行。     

控制酸性矿山废水的污泥屏障压缩特性

污泥屏障通过物理拦截以及化学作用可以有效控制重金属离子迁移,采用污泥屏障处理酸性矿山废水(AMD)已被证明具有可行性.作为尾矿渣处置场屏障的主体材料,研究污泥压缩特性很有必要.实验结果表明,对于含水率相同的压实污泥试样,孔隙比随干密度增大而减小,最终趋于1;干密度相同的试样,最优含水率的孔隙比随应力增大减小最快.试样压缩系数随干密度增大而减小,随含水率增大先增大后减小,最优含水率的压缩系数为0.8 MPa-1.AMD溶液作孔隙液能提高试样压缩系数.通过对比分析有机质土的压缩特性,为以后的深化研究提供相关参数支持.     

不同改性剂改善污泥土工性质的比较研究

选择了泥土、矿化垃圾、粉煤灰和建筑垃圾4种改性剂改性城市污水处理厂污泥(以下简称污泥)。结果表明:(1)随着4种改性剂与污泥的混合比增大,混合物含水率降低。(2)当混合比为0.7(质量比)时,各种混合物的抗压强度都达到50kPa的填埋要求;当混合比为0.3～1.0时,混合物的抗压强度随着混合比的增大呈指数形式增大;比较4种改性剂对抗压强度的增大能力,粉煤灰最强,建筑垃圾次之,泥土和矿化垃圾较弱。(3)在50kPa预压力下,混合物要达到不小于25kPa的抗剪强度,泥土与污泥最小混合比为1.0,矿化垃圾与污泥最小混合比为1.0,粉煤灰与污泥最小混合比为0.7,建筑垃圾与污泥最小混合比为0.7。(4)除加泥土的混合物外,混合物压缩系数随着混合比的增大呈总体下降趋势。(5)粉煤灰除臭效果最好,矿化垃圾次之,建筑垃圾较差,泥土最差。     

垃圾填埋场污泥坑原位修复工程实践

垃圾填埋场内污泥坑的存在严重影响填埋场竖向扩建和填埋堆高。对某垃圾填埋场内污泥坑进行现场勘察取样、原位测试与室内实验,获得污泥的分层及沿深度变化的物理、力学特性,并针对不同分层的污泥,提出表层垃圾清除、污水抽排、泥水混合污泥土工管袋脱水、流塑、软塑污泥原位固化综合处理方法。对污泥坑抽排污水过程中垃圾堆体边坡进行渗流稳定分析,发现渗滤液水位快速下降将导致污泥坑垃圾边坡滑移失稳,在污泥坑治理过程中应采取相应措施。根据污泥坑上覆80~120 m垃圾堆体沿原位固化污泥滑移稳定分析,获得污泥坑原位固化处理强度指标,不排水抗剪强度Cu为40 k Pa。     

准好氧填埋工艺陈腐垃圾的理化特性变化规律

针对准好氧填埋工艺,研究了实际填埋场1~5年陈腐垃圾的含水率、有机质和腐殖质等理化特性动态变化规律。结果表明,垃圾含水率、电导率、有机质均随着填埋时间的增加呈现明显的降低趋势,且导气管附近垃圾样品(0 m)垃圾含水率、有机质降低速度相对较快,在填埋3年后含水率达到相对稳定的状态,有机质含量的降低主要发生在填埋处置的第2年;垃圾pH值、腐殖质提取率和富里酸含量呈现明显升高的趋势,且距离导气管较远垃圾样品(15 m)pH值升高速度相对较快,在填埋1年左右存在明显的酸化阶段;胡敏酸含量和HA/FA比则呈现出前期升高后期降低的趋势,其中导气管附近垃圾样品(0 m)的变化明显快于距离导气管较远(15 m)的垃圾。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.