共查询到20条相似文献,搜索用时 314 毫秒
1.
《环境工程学报》2015,(7)
以工业废弃物为主要原料,经过同时聚合制备聚硅酸阳离子絮凝剂(PSiC)。实现硅酸缩合自聚、铁铝离子羟化聚合以及硅与铁铝离子聚合同步交互进行。利用PSiC处理印染废水,研究PSiC去除浊度、色度和和UV254的性能,分析其除污染机理。结果表明,PSiC处理印染废水时最佳投放量为80mg/L,此时浊度和色度去除率分别达到50%和90%。废水pH为7、PSiC投加量80mg/L时对印染废水UV254的去除率为65%。pH和投加量过大或过小都会降低PSiC去除UV254的效果。在混凝搅拌初期UV254迅速下降,停止搅拌后又略有所上升。沉淀初期UV254稍有波动,沉降10min后基本趋于稳定。 相似文献
2.
3.
以白碳黑、硅灰、硅藻土和硅胶筛选硅质原料,并与钙质原料电石渣制备了水化硅酸钙。借助XRF、BET、FTIR等表征手段,通过多次重复除磷实验,研究了硅质原料特性对水化硅酸钙回收磷性能的影响。结果表明,白碳黑具有极高的反应活性,因此可作为制备具有磷回收特性的水化硅酸钙的硅质原料。结合XRD等表征发现,白碳黑的有效利用率是影响水化硅酸钙回收磷性能的关键,该利用率取决于白碳黑与电石渣的摩尔配比以及水热反应温度。当电石渣与白碳黑的摩尔比为1.6:1,反应温度为170℃时,白碳黑具有最佳的利用效率。该条件制备的水化硅酸钙可作为晶种,在其表面结晶形成羟基磷灰石,从而达到磷回收的目的,磷回收后固体物质中的磷含量为19.05%。 相似文献
4.
以白碳黑、硅灰、硅藻土和硅胶筛选硅质原料,并与钙质原料电石渣制备了水化硅酸钙。借助XRF、BET、FT—IR等表征手段,通过多次重复除磷实验,研究了硅质原料特性对水化硅酸钙回收磷性能的影响。结果表明,白碳黑具有极高的反应活性,因此可作为制备具有磷回收特性的水化硅酸钙的硅质原料。结合XRD等表征发现,白碳黑的有效利用率是影响水化硅酸钙回收磷性能的关键,该利用率取决于白碳黑与电石渣的摩尔配比以及水热反应温度。当电石渣与白碳黑的摩尔比为1.6:1,反应温度为170℃时,白碳黑具有最佳的利用效率。该条件制备的水化硅酸钙可作为晶种,在其表面结晶形成羟基磷灰石,从而达到磷回收的目的,磷回收后固体物质中的磷含量为19.05%。 相似文献
5.
6.
活性硅酸混凝剂PFASSC处理造纸废水 总被引:5,自引:0,他引:5
利用硅酸钠、硫酸铝、三氯化铁和硫酸为主要原料制备了复合型活性硅酸混凝剂PFASSC并对造纸废水进行了处理,得到活性硅酸混凝剂PFASSC最佳配方为:PH=2.0(Fe^3++Al^2)/SiO2(摩尔比)=1.5,Fe^3+/Al^3+(摩尔比)=1.0,与常用混凝剂相比,PFASSC混凝剂处理造纸废水对除浊、脱色和去除CDDCr有更加优良的性能。 相似文献
7.
针对二氧化锰对废水中氯离子电解生成活性氯具有较好催化活性的特点,以软锰矿为原料制备一种新型粒子电极,将其用于三维电极系统处理油气田高含氯废水,利用活性氯的强氧化性进一步强化废水中难降解有机物SMP的处理;并考察软锰矿粒子电极制备条件对电极性能和电解效果的影响。结果表明:软锰矿与石墨质量比6∶4、PTFE分散液加入量10%、330°C下灼烧2 h为软锰矿粒子电极最优制备条件;与常规活性炭粒子电极相比,软锰矿粒子电极电解活性氯的产生量、COD去除率均显著优于活性炭粒子电极;且软锰矿粒子电极在重复使用多次后,活性组分流失量较小,对SMP的降解效率仍较高,保持了稳定的电催化性能。 相似文献
8.
外源硅对不同pH水田土壤吸附铅的影响 总被引:2,自引:0,他引:2
通过等温吸附实验,研究了加硅对2种不同pH水田土壤吸附铅特性的影响。实验中用硝酸中和硅酸钠的碱性,各处理间钠离子和硝酸根离子的差异以硝酸钠补齐,消除了因硅酸盐的加入改变体系pH及伴随离子对土壤吸附铅可能产生的影响。结果表明,在本实验条件下,Langmuir方程、Freundlich方程和Temkin方程都能较好地描述不同硅浓度条件下两种土壤对铅的吸附特征,但以Freundlich模型为最优;加硅促进了酸性土壤对铅的吸附,抑制了碱性土壤对铅的吸附。 相似文献
9.
聚硅基复合氯化铁絮凝剂的制备及其在采油废水处理中的应用 总被引:2,自引:0,他引:2
采用硅酸钠制备聚硅酸,探讨了活化pH、活化剂、硅酸钠浓度(以SiO_2质量分数计)及聚合温度等因素对聚硅酸稳定性的影响.利用聚硅酸及氯化铁制备聚硅基复合氯化铁(PSiF),并通过正交试验分析了活化pH、Si/Fe(摩尔比)、OH/Fe(摩尔比)、制备时间对PSiF絮凝性能的影响.综合考虑絮凝性能、稳定性以及经济性等因素,确定PSiF适宜的制备条件为SiO_2质量分数2%~3%;活化pH为2~3;Si/Fe为0.50~0.75;OH/Fe为0.50~0.75;制备时间为0.5 h;聚合温度低于25℃.对比PSiF、PAC、FeCl_3对采油废水的处理效果,PSiF除浊、除COD效果以及经济性最好,是一种应用前景广阔的新型絮凝剂. 相似文献
10.
11.
Árpád Ambrus 《Journal of environmental science and health. Part. B》2013,48(3):435-442
Abstract A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits. 相似文献
12.
介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠 相似文献
13.
不同泥源对厌氧氨氧化反应器启动的影响 总被引:2,自引:1,他引:1
采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。 相似文献
14.
Janusz A. Pudykiewicz Anna S. Koziol 《Atmospheric environment (Oxford, England : 1994)》1998,32(24):5541
The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing. 相似文献
15.
造纸废水混凝处理中SFT助凝替代性研究 总被引:1,自引:0,他引:1
中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染 相似文献
16.
活性炭三维电极法对印染废水的处理研究 总被引:4,自引:0,他引:4
对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25~30 V,进水pH值6.5~7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。 相似文献
17.
18.
以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径<1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径. 相似文献
19.
Evaluation of the presence of drugs of abuse in tap waters 总被引:1,自引:0,他引:1
A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L−1, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L−1. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L−1). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L−1 (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L−1, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L−1). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L−1 (Spain) and 0.3 ng L−1 (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected. 相似文献
20.
Volker Berding Stefan Schwartz Michael Matthies 《Environmental science and pollution research international》1999,6(1):37-43
The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters
(inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation,
on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency.
The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity
was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters),
and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity
to 961, and the maximal dimension is 21. 相似文献