沉淀剂对稀土Gd掺杂SnO2/Ti涂层阳极性能的影响

实验采用共沉淀法，以无机盐SnCl₄·5H₂O、Sb₂O₃、Gd(NO₃)₃为前驱体，制备稀土Gd掺杂SnO2/Ti多组分涂层阳极。研究了用不同沉淀剂制备的电极以苯酚为目标有机物的电化学降解特性，以考察沉淀剂对稀土Gd掺杂SnO₂/Ti阳极性能的影响；并对所制备的涂层阳极进行了SEM、XRD、XPS等表征及阳极极化曲线、循环伏安曲线测试，分析并讨论了沉淀剂对稀土Gd掺杂SnO₂/Ti阳极性能的影响机理。结果表明，沉淀剂对稀土Gd掺杂SnO₂/Ti电极性能有较大的影响，在本实验条件，以氨水为沉淀剂所制备的电极电催化性能较好，稳定性能较高。     

电解浮选用于活性污泥固液分离的正交实验研究

本研究旨在探索用电解浮选进行活性污泥固液分离的可行性。研究通过小试试验确定电解浮选进行活性污泥固液分离的适宜工艺条件，在装有Ti/RuO₂-IrO₂-TiO₂阳极、Ti阴极的电解浮选槽中进行了活性污泥固液分离的研究，针对影响电解气浮工艺的4个主要影响因素（水力停留时间、接触室电流密度、分离区电流密度和接触室极板间距）及3个合适的水平进行正交试验。结果表明，分离区电流密度是最主要影响因素。当进水SS浓度为1687 mg/L时，在停留时间为25 min，接触室电流密度为5 mA/cm²，分离区电流密度为4 mA/cm²，极板间距为3 mm的条件下进行电解浮选验证性试验，悬浮固体颗粒物去除率较高，去除率为98.9% ，能耗0.54 kWh/m³。     

电催化氧化处理除草剂异草酮废水的效能简

为有效处理含异草酮除草剂废水，以Sb掺杂Ti/SnO₂电极为阳极，不锈钢板为阴极，采用电催化氧化技术对异草酮废水进行降解，研究了不同影响因素对异草酮去除率的影响，并分析了异草酮的降解效果。结果表明，当异草酮初始浓度为100 mg/L、电流密度为20 mA/cm²、电解质投加量为0.10 mol/L，反应120 min后，异草酮去除率达到94%，此时TOC去除率为57.9%，能耗为25 kWh/m³，且废水的可生化性能显著提高。     

用H2O2/Fe3+处理高浓度含甲醛废水的研究

研究采用H₂O₂/Fe³⁺催化氧化处理高浓度含甲醛废水，探讨了双氧水和催化剂投加量、反应pH及反应温度等操作条件对处理效果的影响，并通过酸溶解回用失活催化剂。结果表明，较优的操作条件为：H₂O₂/COD（质量比）=2.2～2.6，Fe³⁺/H₂O₂（摩尔比）=0.048～0.058，反应pH 1.80～2.68，反应温度50℃，反应时间40 min；在上述操作条件下，甲醛去除率达到99%以上，COD去除率达到85%以上。失活的催化剂可通过稀酸溶解后循环使用，其效果与三价铁盐作催化剂的基本相同。采用H₂O₂/Fe³⁺处理含甲醛废水具有比采用H₂O₂/Fe³⁺较优的效果。     

催化湿式氧化法处理高浓度唑螨酯生产废水的研究

对唑螨酯生产过程中产生的高浓度实际废水采用催化湿式氧化技术在鼓泡式固定床反应器连续反应装置上进行处理。实验表明，制备的复合负载型催化剂CuO-MnO₂-Cr₂O₃/ZrO₂-CeO₂在处理该废水时具有较好的催化活性。通过对反应温度、反应压力、反应空速、气液比和进水pH等工艺条件的考察，得出最佳的工艺条件为：反应温度=220℃，反应压力=5.8 MPa，空速＝1.8 h^-1，V（气）∶V（水）＝260∶1，进水pH＝9，在此条件下COD去除率达到95.2％。     

新型高效气体扩散电极的制备与性能

评述了原位产生H₂O₂的电化学法污水处理技术中使用的主要电极，研究了用石墨制备高效气体扩散电极的方法。对石墨用HNO₃与H₃PO₄的混合液改性，石墨与聚四氟乙烯的质量比为2∶1，电极经350℃煅烧1 h，对溶解O₂还原产生H₂O₂的催化活性最高。仅在pH值很低时，电极的活性较差，在pH=3～9时，电极的活性受pH值变化影响较小。在pH=3时电解150 min，电极的电流效率始终高于72%，H₂O₂浓度达到了274.5 mg/L。     

阴极负载不同催化剂对天然水体中沉积物微生物燃料电池运行特性的影响

考察了阴极负载Co₃O₄和MnOOH对天然水体中沉积物微生物燃料电池（SMFC）产电性能和SMFC对沉积物中有机质去除率的影响。实验结果表明，SMFC阴极负载Co₃O₄和MnOOH后，体系的输出电压由483 mV增大到549 mV和534 mV；相应体系的内阻由206 Ω显著降低到99 Ω和128 Ω，最大功率密度（Pmax）由3.3 mW/m²增大到9.1 mW/m²和6.6 mW/m²。此外，SMFC体系的电流密度与沉积物中烧失量（LOI）、易氧化有机质（ROOM）去除率呈线性关系，并且阴极负载Co₃O₄和MnOOH可以促进阳极沉积物中有机质的去除。     

CuAPO-5分子筛催化氧化水溶液中苯酚的性能

以水热晶化法合成了铜磷铝分子筛CuAPO-5，并用XRD、SEM,FT-IR，UV-Vis等对样品进行了表征，结果表明Cu²⁺进入到了AlPO₄-5分子筛骨架中。研究了以CuAPO-5为催化剂， H₂O₂为氧化剂对水溶液中苯酚的催化氧化性能。在苯酚初始浓度200 mg/L 、H₂O₂添加量1 200 mg/L、pH值5.0、处理温度80 ℃时，处理240 min时苯酚去除率达到100％，TOC去除率达81.76％，析出到溶液中Cu²⁺浓度仅为0.527 mg/L。温度从40 ℃上升到80 ℃时，苯酚的去除率及TOC去除率明显增大，表明温度对催化剂的活性影响显著，相比于均相催化剂骨架Cu催化过氧化氢分解需要更多的能量。重复性实验表明，催化剂性能稳定。     

真空紫外光臭氧降解偏二甲肼的研究

研究比较了臭氧氧化（O₃）、紫外臭氧（O₃/UV）和真空紫外臭氧（O₃/VUV）对推进剂——偏二甲肼的处理效果，O₃/VUV最为有效，反应速率常数分别比O₃/UV和O₃高39.8%和65.6%，中间产物——甲醛去除得更迅速，反应50 min即无法检出。初始pH 9时，O₃/VUV降解偏二甲肼的速率最快，达到0.4461 min^-1；反应速率常数随臭氧投加量的增加而线性增大；随偏二甲肼初始浓度从100 mg/L增加到2 000 mg/L，反应动力学由一级转为零级。碳酸盐浓度在0～2 mmol/L范围内对O₃/VUV降解偏二甲肼没有明显的抑制作用。偏二甲肼的无机氮产物以氨离子为主，无机氮只占总氮的40%～60%，说明仍有相当比例的氮以有机氮形式存在。     

UV/Fenton法预处理N-甲基苯胺生产废水

采用UV/Fenton法对N-甲基苯胺生产废水进行预处理。当原水COD约为3 400 mg/L时，在适宜操作条件（H₂O₂投加量为50 mL/L，Fe²⁺投加量为1.209 g/L，pH＝5.0，反应时间为30 min）下的COD去除率可达90％以上。同时得到Fenton试剂处理该废水的适宜条件为：H₂O₂投加量为60 mL/L，Fe²⁺投加量为1.692 g/L，pH为5.0，反应时间30 min；单独UV辐照处理该废水的较适宜条件为：反应时间为20 min， pH＝5.0。最后就3种处理方法进行了比较，发现UV对Fenton试剂处理N-甲基苯胺生产废水具有一定促进作用。反应前后的紫外光谱说明，经UV/Fenton反应后，原水中的含苯环物质已得到了彻底的氧化分解。     

Performance of Gd-doped Ti-based Sb-SnO2 anodes for electrochemical destruction of phenol

The performance of electrodes for the electro-catalytic decomposition of a model pollutant (phenol) was enhanced using Gd-doped Ti/SnO(2)-Sb electrodes prepared by a thermal deposition method. Phenol degradation followed first-order rate kinetics, with the maximum rate achieved using a 2% Gd doping level (molar ratio based on Gd:Sn) for tests conducted over a doping range of 1-10%. The first-order rate constant with 2% Gd was 0.044 min(-1), versus 0.026 min(-1) obtained with the control (plain Ti/SnO(2)-Sb). TOC removal and UV scans revealed that different intermediates were produced for different Gd contents, and that destruction efficiencies of these intermediates also varied with Gd doping levels of 1-5%. Electrodes were characterized by scanning electron microscopy, X-ray diffraction, electron dispersive spectrometry, and X-ray photon-electron spectroscopy. It is suggested that the state of specific active sites on the electrode surface and the oxygen transfer activity at the electrode/electrolyte interface affect the performance of anodes with different compositions.     

CeO2-CoO／ACF低温SCR烟气脱氮性能的研究

活性炭纤维（ACF）经硝酸处理后采用浸渍法制备了CeO2-CoO／ACF复合催化剂，测试了其在以氨气为还原剂的低温SCR过程中的催化活性，同时研究了金属氧化物浸渍顺序及负载量、催化剂煅烧温度、空速比（SV）、NH，／NO（摩尔比）、O2含量等因素对NO转化效率的影响。研究发现，负载量为10％的CeO2-CoO／ACF复合催化剂经煅烧后在120—240℃时具有很高的催化活性，并且在N0初始浓度为1000mg／m3、空速比（SV）为6000h～、NH3／NO为1．05、O：体积分数在3．0％时具有较高的NO转化效率。     

Evaluation of different electrochemical methods on the oxidation and degradation of Reactive Blue 4 in aqueous solution

The oxidation of a reactive dye, Reactive Blue 4, RB4, (C.I. 61205), widely used in the textile industries to color natural fibers, was studied by electrochemical techniques. The oxidation on glassy carbon electrode and reticulated vitreous carbon electrode occurs in only one step at 2.0 < pH < 12 involving a two-electron transfer to the amine group leading to the imide derivative. Dye solution was not decolorized effectively in this electrolysis process. Nevertheless, the oxidation of this dye on Ti/SnO2/SbO(x) (3% mol)/RuO2 (1% mol) electrode showed 100% of decolorization and 60% of total organic carbon removal in Na2SO4 0.2 M at pH 2.2 and potential of +2.4V. Experiments on degradation photoelectrocatalytic were also carried out for RB4 degradation in Na2SO4 0.1 M, pH 12, using a Ti/TiO2 photoanode biased at +1.0 V and UV light. After 1h of electrolysis the results indicated total color removal and 37% of mineralization.     

三维电极法深度处理维生素生产废水

采用三维电极法对维生素废水进行深度处理,分别以钛涂钌铱板、铁板和不锈钢板作为电极阳极,石墨板作为电极阴极,柱状活性炭作为粒子电极,结果表明,当以钛涂钌铱板作为阳极,以粒径为1 mm的柱状活性炭作为粒子电极时电解效果最好,COD和色度去除率最高。实验选择电解电压、电极板间距、电解时间和初始pH值作为主要影响因素进行正交实验,实验研究证明,各因素的影响大小为电解电压>电极板间距>电解时间>初始pH值,得到的最佳参数组合分别为:电解电压为10 V,电极板间距为8 cm,电解时间为20 min,初始pH值为4,得到COD和色度最大去除率分别为59.5%和93.57%。     

基于Ti/SnO2阳极氧化法的典型染料废水电化学氧化规律

采用Ti／SnO2电极间接阳极氧化法处理直接深棕M和活性艳蓝KNR模拟染料废水，研究电解质种类、pH、电压、NaCl投加量及电解时间对其降解效果的影响；在最佳组合条件下，通过分析uV—Vis光谱以及降解过程中氮元素的存在形式，研究上述2种染料的降解规律。结果表明，在pH为3，电压20V，NaCl投加量为2．5g／L的条件下，电解30min后，直接深棕M和活性艳蓝KNR的脱色率分别达到80％和95％，60min后直接深棕M的COD去除率可达75％，活性艳蓝KNR的COD去除率达到90％；电解60min后，直接深棕M的偶氮双键完全破坏，萘环和苯环结构被逐步降解，活性艳蓝KNR溶液电解2min，其分子结构中的蒽醌共轭体系被破坏，随反应的进行，蒽醌结构逐渐被破坏，染料逐步降解。     

CeO_2-CoO/ACF低温SCR烟气脱氮性能的研究

活性炭纤维(ACF)经硝酸处理后采用浸渍法制备了CeO2-CoO/ACF复合催化剂,测试了其在以氨气为还原剂的低温SCR过程中的催化活性,同时研究了金属氧化物浸渍顺序及负载量、催化剂煅烧温度、空速比(SV)、NH3/NO(摩尔比)、O2含量等因素对NO转化效率的影响。研究发现,负载量为10%的CeO2-CoO/ACF复合催化剂经煅烧后在120~240℃时具有很高的催化活性,并且在NO初始浓度为1 000 mg/m3、空速比(SV)为6 000 h-1、NH3/NO为1.05、O2体积分数在3.0%时具有较高的NO转化效率。     

电极材料对电解法处理循环式准好氧垃圾填埋场渗滤液效果的影响研究

分别用3种不同材料电极(不锈钢、Ti/Pt和Ti/RuO2-IrO2)作阳极、石墨电极作阴极在同一条件下分别对循环式准好氧填埋垃圾场渗滤液进行电解处理对比研究.研究结果表明,随着电解时间的变化,渗滤液中的COD、BOD5、BOD5/COD、重金属离子浓度、色度和pH值均会发生改变.当电解时间为10～20 min时,用上述3种电极作阳极电解均会出现渗滤液COD、BOD5、BOD5/COD增大的现象;当电解时间为30～40 min时,用Ti/RuO2-IrO2或Ti/Pt电极作阳极电解均可使渗滤液的色度降为0;当电解时间为120 min时,分别用3种电极作阳极电解都可使渗滤液中的COD、BOD5和重金属得到有效的去除,其中用Ti/RuO2-IrO2电极作阳极电解对COD、BOD5的去除效果最好:用Ti/Pt电极作阳极电解对Pb2 的去除效果最好.     

Characteristics of electrolysis, ozonation, and their combination process on treatment of municipal wastewater.

The characteristics of municipal wastewater treatment by electrolysis, ozonation, and combination processes of electrolysis and aeration using three gaseous species (nitrogen [N2], oxygen [O2], and ozone [O3]) were discussed in this research using ruthenium oxide (RuO2)-coated titanium anodes and stainless-steel (SUS304) cathodes. Electrolysis and electrolysis with nitrogen aeration were characterized by a rapid decrease in 5-day biochemical oxygen demand (BODs) and total nitrogen and a slow decrease in chemical oxygen demand (COD). In contrast, ozonation, electrolysis with oxygen aeration, and electrolysis with ozone aeration were characterized by transformation of persistent organic matter to biodegradable matter and preservation of total nitrogen. The best energy efficiency in removing BOD5 and total nitrogen was demonstrated by electrolysis, as a result of direct anodic oxidation and indirect oxidation with free chlorine produced from the chloride ion (Cl-) at the anodes. However, electrolysis with ozone aeration was found to be superior to the other processes, in terms of its energy efficiency in removing COD and its ability to remove COD completely, as a result of hydroxyl radical (*OH) production via cathodic reduction of ozone.     

Influence of metal oxides on PCDD/Fs formation from pentachlorophenol

Chlorophenols (ClPhs) are considered as important precursors for PCDD/Fs formation. The influences of series of metal oxides including MgO, Al2O3, CaO, BaO, TiO2, V2O5, MnO2, Fe2O3, Co3O4, CuO, Ag2O, ZnO, HgO, SnO, PbO, La2O3, CeO2, and Eu2O3 on PCDD/Fs formation from pentachlorophenol (PCP) were investigated in a laboratory-scale reactor. The results indicated that most of the above metal oxides have obvious suppressing effects on the total amount of PCDD/Fs formation from precursor PCP except for CuO, ZnO, MnO2, TiO2 and Co3O4 with promotion effects at 280 degrees C for 2 h. Although MgO, Al2O3, Fe2O3, PbO, La2O3 and Eu2O3 could reduce the amount of octachlorinated dibenzo-p-dioxin (OCDD), they promote the formation of more toxic 1,2,3,4,6,7,8-HpCDD at the same time. The total suppressing efficiencies of several metal oxides including CaO, BaO, PbO, Ag2O, HgO and SnO which have lower Z/r (charge to radius ratio) <2 are all over 90%. The theories of generalized acid-base and atomic parameter (Z/r) were used to speculate the effecting mechanisms. The factors including time and temperature on suppressing efficiencies of CaO, BaO and PbO have also been studied in the present paper. The results showed that the total suppressing efficiencies of CaO, BaO and PbO increase with the increase of heated time and temperature.     

电化学方法用于酸性红B模拟废水脱色试验研究

本文研究了两种电极材料 (SnO2 Ti和RuO2 Ti)对酸性红B模拟废水的脱色效果 ,考察了不同 pH、电流密度(j)及外加电解质 (Na2 SO4/NaCl)对处理过程的影响。结果表明 ,两种电极材料都能对酸性红B染料废水进行有效脱色 ,主要是Cl-在电解过程中的间接氧化作用 ,同时也包括电极表面的直接氧化作用。