基于生物表面活性剂的柴油微乳体系构建与性能研究

以生物表面活性剂鼠李糖脂（RL）为表面活性剂，中长碳链正构醇（正丁醇、正戊醇、正己醇、正庚醇及正辛醇）为助表面活性剂，采用滴定法制备RL／柴油／正构醇／水柴油微乳体系，并考察了表面活性剂用量（Km）、助表面活性剂醇的种类及用量（δas）及离子强度对柴油微乳体系最大增溶水量（Wo）的影响，并对不同条件下获得的柴油微乳体系的运动粘度（μ）和表面张力（γ）进行了表征。通过荧光法测得RL在柴油中的临界胶束浓度CMC为7g／L。当生物表面活性剂与柴油的质量比Km为0．02，助表面活性剂选用正庚醇且醇与表面活性剂的质量比δgs为0．1，NaOH溶液质量分数为0．06％时，柴油微乳体系的肛和T较低，形。最大，性能较佳。     

胶团强化超滤中表面活性剂结构差异对苯酚增溶性能的影响研究

在胶团强化超滤(MEUF)技术处理有机物废水中,采用多因素正交实验研究了3种不同类型的阳离子型表面活性剂,即疏水链长度相同,而亲水基头不同;亲水基头相同,而疏水链长度不同的表面活性剂,分析基团差异对于苯酚增溶的影响。结果表明,十六烷基氯化吡啶(CPC)对于苯酚的去除效果最好,其次是十八烷基三甲基溴化铵(OTAB),最后是十六烷基三甲基溴化铵(CTAB)。综合去除效果和经济性两方面考虑,在单因素超滤实验中选择OTAB来重点研究表面活性剂浓度和电解质浓度两个操作参数对于苯酚增溶的影响。     

石油醚为油相的乳状液膜稳定性研究

以石油醚为油相,以聚异丁烯单丁二酰亚胺(T151)、聚异丁烯多丁二酰亚胺(T155)为表面活性剂,制备了W/O(W代表水相,O代表油相,下同)单重乳液和W/O/W多重乳液,并进行了乳状液膜稳定性的研究.以破乳率、泄漏率和表观溶胀率为衡量指标,考察了表面活性剂种类和用量、油水比(油相体积与内水相体积的比)、乳水比(W/O单重乳液的体积与外水相体积的比)、制乳转速等参数对乳状液膜稳定性的影响.结果表明,表面活性剂的用量、油水比、乳水比和制乳转速均存在最佳值,即:(a)T151体积分数6%,油水比1:1,一次制乳转速3 000 r/min,乳水比为1:6,二次制乳转速300 r/min;(b)T155体积分数4%,油水比1:1,一次制乳转速4 000 r/min,乳水比为1:8,二次制乳转速400 r/min,此时的W/O/W多重乳液乳状液膜最稳定.     

蓖麻油衍生微乳液对菲的增溶和洗脱作用及其对菲污染土壤的修复机理

比较研究了蓖麻油硫酸盐(SCOS)与普通表面活性剂Triton X-100(TX100)、Tween 80(TW80)、Brij35、十二烷基苯磺酸钠(SDBS)和十二烷基硫酸钠(SDS)等对菲的增溶和洗脱作用.结果表明,菲表观溶解度与SCOS的浓度呈单一线性关系,SCOS微乳液对菲的增溶比SR=0.0314为最大,菲在微乳相和水相之间的分配系数logKem=4.44,大于菲在胶束相和水相之间的分配系数(logKmc).1:10土-水体系下,SCOS微乳液对菲污染土壤的清洗速率最快,清洗效率最高.SCOS有望成为土壤有机污染淋洗修复的增效试剂.     

表面活性剂对黄土中石油污染物的解吸影响研究

研究了用表面活性剂去除黄土中柴油类污染物。选用阴离子表面活性剂十二烷基苯磺酸钠和十二烷基硫酸钠 (LAS和SDS)和阳离子表面活性剂十六烷基三甲基溴化铵 (CTAB)对污染的土壤进行解吸实验 ,表明阴离子表面活性剂浓度从 0 .1%增加到 1.0 %时 ,其柴油的去除率可达 2 0 % ,而阳离子表面活性剂去除作用不甚明显。利用摩尔增溶比MSR值求得LAS和SDS的logKm 值为 4.5 5 2和 3 .63 0 ,这和理论的计算值很接近     

表面活性剂CMC对石油烃污染土壤的增溶

研究了表面活性剂羧甲基纤维素钠(carboxyl methyl cellulose,CMC)对土壤中石油污染物的增溶作用。通过批实验,对比研究了CMC和十二烷基苯磺酸钠SDBS 2种表面活性剂的增溶效果,探究了CMC浓度、pH、盐度及回用次数对土壤中石油烃增溶效果的影响。研究结果表明,当CMC浓度为0.5%,增溶时间为24 h时,对TPHs浓度为17 695 mg·kg~(-1)的污染土样,TPHs洗脱率高达60%以上。碱性环境有利于石油烃的洗脱,酸性体系会抑制石油烃的洗脱;增溶作用随盐度的增大而显著增大。在利用CMC对污染土壤进行增溶洗脱时,对于TPHs高浓度污染土壤,可以选择将其洗脱液回用1次或者2次;对于TPHs较低浓度污染土壤,可以选择将其洗脱液回用于较高浓度的污染土壤。     

糖脂类生物表面活性剂去除污染含水层中石油烃的研究

研究了糖脂类生物表面活性剂对石油烃的增溶,并将其用于污染含水层中石油烃的去除。结果表明:石油烃溶解度随着糖脂类生物表面活性剂浓度的增大而增大,糖脂类生物表面活性剂质量浓度为1 200mg/L时,石油烃溶解度达10 077.7mg/L;界面张力随着糖脂类生物表面活性剂浓度的增加而减小,糖脂类生物表面活性剂质量浓度为1mg/L时,界面张力为34.3mN/m,糖脂类生物表面活性剂质量浓度为800mg/L时,界面张力为5.2 mN/m。采用糖脂类生物表面活性剂对污染含水层进行清洗处理,在固液比(质量体积比)为1g∶2mL的体系中,糖脂类生物表面活性剂质量浓度为3 000mg/L,120r/min、10℃下振荡12h,石油烃去除率达70.82%。污染含水层柱冲洗结果表明,糖脂类生物表面活性剂质量浓度分别为1 200、3 000mg/L时,10倍孔隙体积的表面活性剂冲洗后,分别从污染砂样中去除41.81%和63.30%的石油烃。     

填料塔-微乳液增溶吸收法净化甲苯废气

利用甲苯可以和非离子表面活性剂及相应助表面活性剂水溶液形成微乳液,从而增大甲苯表观溶解度的特性,吸收净化甲苯废气。采用微乳液作为吸收剂的填料塔治理甲苯废气,探讨了吸收剂组成、表面活性剂种类及浓度、喷淋量、甲苯浓度负荷和助表面活性剂的加入及其种类对甲苯去除率的影响。结果表明,微乳液吸收处理甲苯废气具有显著的效果,最大去除率达41%;经过体系筛选采用Tween-20作为表面活性剂,此时最适喷淋量为40 L/h(液气比为1∶5),且随着甲苯浓度负荷的升高,甲苯去除率随之增加;添加助表面活性剂可以不同程度地提高甲苯的去除率,Tween-20/正丁胺/甲苯/水微乳体系为吸收甲苯的最佳体系,此时最高去除率可达65%。     

车用环保甲醇柴油制备工艺的研究

根据微乳液理论和甲醇分子结构的特点，选择出适合制备甲醇柴油微乳燃料的助溶剂和助溶表面活性剂，并对乳化过程进行了机理和实验研究。由实验得出微乳燃料最佳制备工艺条件为：常温下甲醇、0#柴油、脂肪酸甲酯、正丁醇分别占乳液质量的12%、50%、30%和8%，搅拌速度300 r/mim，乳化时间3 min。对最佳配方所得样品的粒径分析发现，粒径大小在30～140 nm之间，微乳液具有较好的高温稳定性、低温稳定性和机械稳定性，外观保持均一，1年内无沉淀或分层析出。     

土壤非饱和带柴油入渗的试验研究

通过土柱模拟试验研研了0#轻质柴油(简称柴油)在不同含水率和容重的壤土及砂土中的入渗及残留特征.结果表明:(1)相同时间内,柴油在壤土中的润湿锋面下渗距离随含水率的增加不断减小,风干土中柴油穿透时间最短;柴油在砂土中的润湿锋面下渗距离随含水率的增加先增大后减小,含水率为10.0%的砂土中柴油穿透时间最短.土壤含水率对润...     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.