定流量条件下壤土夹层对苯和Br~-穿透包气带的影响

为研究壤土夹层对VOCs穿透包气带的影响,以苯为特征污染物,Na Br为示踪剂开展室内的渗流模拟土柱实验。模拟包气带对苯的吸附实验,确定吸附平衡时间、最大吸附量,分析砂土和粉质壤土对苯的吸附特性;设计渗流土柱实验,模拟定流量降雨条件下苯在不同构型的土柱中的迁移过程,分析壤土夹层在时间和空间上对苯穿透包气带到达含水层的影响,并得出弥散系数和阻滞系数。结果表明,相对黏粒含量高的壤土夹层显著改变了溴离子的穿透曲线,对污染水有明显的阻水减渗作用,不仅延迟了苯向含水层的迁移时间,而且在一定程度上起到了吸附、降解的阻滞作用,有效降低了特征污染物穿透包气带的含量。     

土壤柴油污染修复的抽气提取去除实验研究

为得到土壤气相抽提(SVE)去除柴油的优化条件，进行了一维土柱抽气提取去除柴油污染物的实验研究，研究不同初始含水率、不同抽气量对污染土壤中柴油去除率的影响及不同深度残留柴油的变化规律。结果表明：在本实验模拟的范围内，抽气量越大，SVE处理效果越好；初始含水率越低，处理效果越好；此外，不同深度去除率变化的规律基本上是随深度的增大而减小。实验结果可为土壤轻油污染实际治理提供实验数据基础。     

不同水分条件下活性污泥对土壤中DOM产生及DDT降解的影响

采用盆钵实验,通过控制淹水、田间最大持水量和60%相对含水量3种水分条件系统研究施用活性污泥(AS)对不同质地土壤中DOM的产生消长规律及DDT降解的影响,旨在为农药污染土壤修复及农产品清洁生产提供理论依据。结果表明:1)不同水分条件下AS均能提高土壤中DOM的含量,且随添加比例增加而增加;2)不同水分条件下AS均能促进土壤中p,p'-DDT降解,淹水条件下添加1%~3%的AS使粘土、壤土和砂土中p,p'-DDT的降解率分别提高4.0%~45.0%、2.7%~48.9%和2.2%~35.4%;最大持水量条件下粘土、壤土和砂土中p,p'-DDT的降解率分别提高2.9%~40.9%、1.9%~46.9%和2.1%~34.3%;60%相对含水量条件下粘土、壤土和砂土中p,p'-DDT的降解率分别提高3.0%~40.9%、2.1%~45.0%和1.7%~31.6%;3)不同水分条件下,不同质地土壤中添加AS后DOC含量与p,p'-DDT含量呈显著正相关。上述结果表明不同水分条件下AS对p,p'-DDT降解的促进效果表现为淹水条件最大持水量60%相对含水量,p,p'-DDT在不同质地土壤中的降解速度表现为壤土粘土砂土。     

乙二胺还原的氧化石墨烯对镉离子的动态吸附

以乙二胺(EDA)还原氧化石墨烯(GO)制得一种吸附剂材料,即还原态氧化石墨烯(RGO)。考察了动态条件下Cd2+溶液的初始浓度、流速及吸附床高度对穿透曲线的影响,同时利用Bed-Depth-Service Time(BDST)模型对吸附床高度与穿透时间的关系进行线性拟合分析,研究了RGO对Cd2+溶液的动态吸附性能。结果表明,RGO可以有效地去除水溶液中的Cd2+,随着吸附床高度的增加,离子的去除率增大,穿透时间延长;当溶液初始浓度增大时穿透时间缩短,离子的去除率减小;而溶液的流速加快,穿透时间和去除率都相应减小。吸附床高度与穿透时间的关系可用BDST模型较好地进行描述,预测新的操作条件下的穿透时间与实验值误差均小于5%。     

电动力学技术修复苯酚污染土壤的研究

用电动力学技术对苯酚污染砂土的修复进行了实验研究.探讨了苯酚污染砂土电动力学修复的可行性及在不同电场强度下苯酚的迁移特征和机制.研究了采用添加阴离子表面活性剂十二烷基苯磺酸钠(LAS)和控制液(柠檬酸和NaOH)等对迁移效果的影响,以及苯酚在砂土中的迁移和分布规律.实验结果表明,在电场作用下苯酚在砂土中发生富集.在电场强度为2.0V/cm时的苯酚富集效果明显,比在电场强度为0.5 V/cm时苯酚多增加30%,且向阳极的迁移距离增大了12 cm;在阴极添加不同浓度的LAS,苯酚在砂土中的富集效果不同,LAS浓度越大向阳极迁移得越快富集效果越明显,当LAS为0.046 0 mol/L时苯酚最高增加了143%;向阳极添加NaOH,苯酚在阳极区增加了136%,比向阴极添加柠檬酸的效果明显.     

醇对柴油微乳体系性能的影响

采用AOT为表面活性剂,不同碳链长度正构醇为助表面活性剂,通过稀释法制备了AOT/柴油/正构醇/水微乳体系。考察了醇与表面活性剂的质量比(r)和正构醇的碳链长度对柴油微乳体系的影响,对不同条件下制备的微乳体系的电导率(δ)、界面张力(γ)及运动粘度(μ)进行了表征。结果表明,采用正丁醇时,微乳体系会出现渗滤现象。采用其他醇时,微乳体系的最大增溶水量(W0)随碳链长度增加而减小,随r增大先增大后减小;随增溶水量(W)增加,δ增大直至达到稳定,γ减小,μ增大;随醇碳链长度增大,δ减小,γ、μ增大;随r增大,δ增大,γ、μ减小。采用正戊醇(r=0.4)时,微乳体系的W0最大,γ、μ均较小,柴油微乳液体系的性能较佳。     

温度和表面活性剂对菲在土壤中吸附的影响

通过静态吸附实验,研究了北京地区土壤对菲的吸附行为,考察了温度和表面活性剂对菲吸附的影响.结果表明,6种土样对菲的吸附等温线均较好地符合Freundlich吸附模式,其吸附能力的大小顺序为:轻壤土>轻粘土>砂壤土>中壤土>重壤土>紧砂土;温度升高不利于菲在土壤中的吸附;十二烷基苯磺酸钠(LAS)和十六烷基三甲基澳化铵(CTAB)均利于菲在土壤表面的解吸,LAS和CTAB对菲的解吸率最高可达66.2%和31.8%,且LAS的解吸效果更好.     

控制酸性矿山废水的污泥屏障压缩特性

污泥屏障通过物理拦截以及化学作用可以有效控制重金属离子迁移,采用污泥屏障处理酸性矿山废水(AMD)已被证明具有可行性.作为尾矿渣处置场屏障的主体材料,研究污泥压缩特性很有必要.实验结果表明,对于含水率相同的压实污泥试样,孔隙比随干密度增大而减小,最终趋于1;干密度相同的试样,最优含水率的孔隙比随应力增大减小最快.试样压缩系数随干密度增大而减小,随含水率增大先增大后减小,最优含水率的压缩系数为0.8 MPa-1.AMD溶液作孔隙液能提高试样压缩系数.通过对比分析有机质土的压缩特性,为以后的深化研究提供相关参数支持.     

土壤理化性质对Fe~0还原硝基苯的影响

采用零价铁（Fe0）还原降解土壤中的硝基苯,考察土壤理化性质对还原效果的影响。结果显示,当2 g土壤中NB含量约为2.5×10-6mol/g,铁粉用量为50 mg,土壤含水量为75%时,控温25℃条件下反应1 h,硝基苯在松砂土和中壤土中的还原率分别可达到82.9%和91.1%。硝基苯在2种土壤中的还原率表现出中壤土〉松砂土的规律;土壤微生物和土壤有机质含量升高有利于反应进行;粒径偏小的中壤土中硝基苯还原较彻底。NB在土壤中的老化时间对Fe0还原效果影响较小。     

轻质非水相流体(柴油)在多孔介质中的垂向运移

紫外分光光度计为测量手段,通过简易一维土柱实验装置模拟了在不同条件下柴油在多孔介质中的运移。实验发现:柴油在两种不同粒径的砂土中垂向迁移的规律大致相同,并在持续淋滤108 h后,约90%的残余柴油都聚集在距离表层30 cm的范围内;间歇淋滤比持续淋滤更容易使柴油聚集在毛细带,不易向深处迁移;并在一定程度上验证了LNAPLs在地下环境中运动的渗漏、顶托阶段。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

实验室质量管理体系内部审核的策划

在实施ISO／IEC 17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核策划阶段的关键环节，提出审核范围确定、审核计划和抽样方案制订的质量控制要求，为有序高效地实施内部审核提供了技术方法。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.