剩余污泥对酸性大红G的吸附

以剩余污泥为吸附剂,研究其对模拟废水中酸性大红G的吸附条件及吸附机理。结果表明,剩余污泥对酸性大红G的吸附是一个快速过程,吸附时间可控制在30 min;其吸附过程同时受液膜扩散和颗粒内扩散的影响,可以用假二级动力学模型进行描述和预测;Freundlich方程可以较好地描述剩余污泥对酸性大红G的吸附行为。污泥未调pH时,对pH<2的溶液中酸性大红G的吸附性能良好;污泥pH为1时,对实验范围(pH<11)溶液中的酸性大红G均可有效吸附;污泥投加量增加,酸性大红G去除率升高,但污泥对酸性大红G的吸附量下降。     

污泥基活性炭吸附Cu2+的应用研究

以城市污水处理厂剩余污泥为原料，以ZnCl₂为活化剂制取污泥基活性炭。以此污泥基活性炭为吸附剂，对含Cu²⁺的废水进行了吸附实验研究。考察了溶液pH值、Cu²⁺的起始浓度对Cu²⁺离子吸附量的影响；利用等温吸附实验作出吸附等温线，并考察了污泥基活性炭吸附剂吸附Cu²⁺的动力学方程。实验结果表明，污泥基活性炭对Cu²⁺具有良好的吸附性能。吸附的最佳pH值为5；吸附符合Langmuir和Freundlich吸附等温方程，吸附为优惠吸附，吸附量随着吸附质溶液浓度的增加而增大；吸附平衡时间为4 h，吸附动力学符合二级动力学方程。     

Triton X-100在土壤颗粒上的吸附特征研究

采用平衡振荡法，研究了砂土对非离子表面活性剂Triton X-100的吸附特征。结果表明，砂颗粒对Triton X-100的吸附能力总体较低，单位吸附含量均＜1.1 mg/g；砂颗粒吸附Triton X-100过程中存在显著的吸附剂浓度效应，砂颗粒上Triton X-100含量随着固液比（吸附剂浓度）的增大而减小；吸附容量q_m与平衡常数K_L值随固液比变化而变化，Langmuir方程适用范围是起始浓度C₀相对较小的固液吸附体系；0.5～1 mm石英砂的吸附能力略＞0.2～0.5 mm石英砂，0.5～1 mm和0.2～0.5 mm石英砂吸附Triton X-100变化特征具有显著的一致性，采用高斯拟合模型可以反映出石英砂吸附Triton X-100的变化规律，相关系数R²均＞0.98。     

厌氧颗粒污泥吸附去除废水中Hg2+的研究

在实验室条件下，以静态、序批的方法研究了厌氧颗粒污泥对废水中Hg²⁺的吸附特性及环境条件对其吸附能力的影响，并通过红外光谱和能谱对比手段，初步探讨了厌氧颗粒污泥吸附Hg²⁺的机理。结果表明，厌氧颗粒污泥对Hg²⁺的吸附过程符合准二级吸附动力学模型，其吸附等温线与Freundlich型拟合得较好(R²=0.9933)；pH是影响吸附的重要因素，在pH值为3～8的范围内，吸附量较大，最大为64.64 mg/g，当pH值大于8或小于3时，吸附量逐渐下降；温度对吸附也有一定的影响，但影响程度不明显。红外光谱和能谱分析表明，厌氧颗粒污泥表面功能基团对Hg²⁺的络合作用是吸附的主要机理，这些基团包括—CH、—CH₂ 、—CH₃、P—H、CO、C—N、PO、SO及C—H，同时在吸附过程中还存在一定的离子交换吸附。     

酸度对好氧颗粒污泥生物吸附含铅废水影响的研究

为了有效地控制铅污染，利用序批式反应器（sequencing batch reactor,SBR）培养的以醋酸钠为碳源的好氧颗粒污泥作为吸附剂，进行生物吸附含铅废水的效能和机理的研究。通过考察酸度、接触时间和Pb²⁺初始浓度等因素的影响，验证好氧颗粒污泥吸附模型，并利用不同的脱附剂，进一步解析其生物吸附的Pb²⁺。实验结果表明, 酸度是影响好氧颗粒污泥生物吸附Pb²⁺的关键因素，当初始pH为5时，好氧颗粒污泥对含铅废水生物吸附效果最好。对低浓度（0～20 mg/L）含铅废水， 10 min后可快速达到吸附平衡。好氧颗粒污泥对Pb²⁺的实测饱和吸附量为101.97±9.00 mg/g，符合朗缪尔（Langmuir）模型。好氧颗粒污泥生物吸附Pb²⁺的过程，伴随着pH值的升高和K⁺、 Ca²⁺、 Mg²⁺的释放，此现象揭示离子交换作用是好氧颗粒污泥生物吸附Pb²⁺的机理之一。此外，脱附剂HNO₃、EDTA和CaCl₂能实现Pb²⁺的回收和好氧颗粒污泥的重复利用。     

ZnCl2法污泥含炭吸附剂对模拟烟气中气态汞的吸附

采用改进的ZnCl₂化学活化法制备污泥含炭吸附剂，利用EDS以及氮吸附等多种测试手段对所制得的污泥含炭吸附剂进行表征，并利用其处理模拟烟气汞污染物，实验结果表明，污泥含炭吸附剂对Hg0的吸附包括物理吸附作用和化学吸附作用，以物理吸附作用为主；随着Hg0入口浓度的提高，污泥含炭吸附剂的Hg0饱和吸附容量增大；随着吸附反应温度的升高污泥含炭吸附对Hg0的吸附作用减弱；在吸附反应温度125℃，Hg0入口浓度60.4 μg/m³，污泥含炭吸附剂和选定的活性炭对Hg0的吸附容量分别为81.2 μg/g和53.8 μg/g，污泥含炭吸附剂对Hg0的吸附作用好于选定的活性炭。     

沸石负载淀粉对Pb2+、Cu2+和Ni2+的吸附性能

将淀粉负载到沸石表面得到新型重金属离子复合吸附剂ZLS。分别从沸石与淀粉质量比、吸附温度、吸附时间、pH与重金属初始浓度不同方面考察了复合吸附剂ZLS吸附 Pb²⁺、Cu²⁺、Ni²⁺的影响。实验结果表明:当沸石与淀粉质量比为10:1,pH为6,吸附温度在30℃时,复合型吸附剂ZLS对Pb²⁺、Cu²⁺和Ni²⁺ 3种重金属离子的吸附效果最好;吸附动力学研究发现,ZLS对Pb²⁺、Cu²⁺和Ni²⁺的吸附行为均符合准二级动力学以及颗粒内部扩散模型;等温吸附数据符合Freundlich模型,吸附状态属于多层吸附。     

MWNTs及MWNTs/TiO2对水中1,2,3-三氯苯的吸附特性研究

采用批量平衡实验，对比研究了多壁碳纳米管（MWNTs）及多壁碳纳米管/二氧化钛复合材料（MWNTs/TiO₂）对水中1,2,3-三氯苯的吸附特性。结果表明，在相同条件下，MWNTs及MWNTs/TiO₂对1,2,3-三氯苯（1,2,3-TCB）的最大吸附量分别为71.8 mg/g和3.05 mg/g，pH值在2~11之间变化时，两者的吸附均不受pH值变化的影响。2种吸附剂的吸附过程均符合拟二级动力学方程，但MWNTs/TiO₂对1,2,3-TCB的吸附速率常数为0.4159 g/(mg·min)，约为MWNTs的50倍左右，说明MWNTs/TiO₂具有更强的吸附驱动力。1,2,3-TCB在2种吸附剂上的吸附过程均可用Freundlich吸附等温线来描述，其热力学参数吉布斯自由能△G⁰均为负、标准焓变△H⁰与熵变△S⁰均为正表明，MWNTs及MWNTs/TiO₂吸附1,2,3-TCB过程为自发吸热反应。与MWNTs相比，MWNTs/TiO₂具有可光催化再生的优点，能用于被污染水体的原位修复。     

改性高炉渣对染料的吸附动力学及热力学研究

以高炉渣和壳聚糖为原料,制备了高温改性高炉渣-壳聚糖复合吸附剂(TBFSC)和盐酸改性高炉渣-壳聚糖复合吸附剂(ABFSC),考察了2种吸附剂对酸性蒽醌蓝和活性艳红K-2BP的吸附性能,研究了吸附过程的等温吸附特征、吸附动力学和热力学。结果表明,2种染料在TBFSC和ABFSC上的吸附更好地符合Langmuir等温方程,表观二级动力学模型能够很好地描述TBFSC和ABFSC的吸附动力学行为。对于染料在TBFSC上的吸附,粒子内扩散过程和液膜扩散过程是该吸附的速控步骤,而液膜扩散过程为ABFSC吸附染料的速控步骤。热力学参数表明,TBFSC和ABFSC对两种染料的吸附都是自发进行的物理吸附,吸附过程均无配位基交换、化学键等强的作用力。     

剩余污泥制备活性炭及其应用研究

以城市污水处理厂二沉池排出的剩余污泥为原料，采用不同活化方法制备活性炭，同时对比活化效果，研究了制备工艺条件对污泥活性炭吸附性能及产率的影响。结合比表面积、孔径分布和扫描电镜表征分析，对制备的污泥活性炭的性能进行评价，并探讨了污泥活性炭作为水处理吸附剂的去除效果。结果表明，以ZnCl₂为活化剂制备的活性炭性能较好，其最佳制备条件为：活化温度550℃，活化时间45 min，ZnCl₂浓度40％，固液比1∶2。制得的污泥活性炭的碘吸附值为496 mg/g，产率为51.8％，比表面积为301.4 m²/g,孔体积为0.37 mL/g，微孔体积为0.08 mL/g，平均孔径为5.78 nm。将该产品用于处理城市污水，投加量为0.8％，吸附平衡时间约为60 min时，对COD的去除率为81％，吸附容量为42.53 mg/g。     

Green preparation of a novel red mud@carbon composite and its application for adsorption of 2,4-dichlorophenoxyacetic acid from aqueous solution

This study reports the eco-friendly preparation of a novel composite material consisting of red mud and carbon spheres, denoted as red mud@C composite, and its application for the removal of 2,4-dichlorophenoxyacetic acid herbicide (2,4-D) from aqueous solution. The preparation route has a green approach because it follows the low-energy consuming one-step hydrothermal process by using starch as a renewable carbon precursor and red mud as a waste from aluminum production industry. Characterization of the red mud@C composite was performed by FT-IR, TGA, SEM, TEM, BET, XRD, and Raman microscopy analyses. The batch adsorption studies revealed that the red mud@C composite has higher 2,4-D adsorption efficiency than those of the red mud and the naked carbon spheres. The maximum removal at initial pH of 3.0 is explained by considering the pKa of 2,4-D and pH of point of zero charge (pH_pzc) of the composite material. The adsorption equilibrium time was 60 min, which followed the pseudo-second-order kinetic model together with intra-particle diffusion model. The isotherm analysis indicated that Freundlich isotherm model better represented the adsorption data, with isotherm parameters of k [15.849 (mg/g) (mg/L)^?1/n] and n (2.985). The prepared composite is reusable at least 5 cycles of adsorption-desorption with no significant decrease in the adsorption capacity.

     

Mechanistic insight into pyrene removal by natural sepiolites

This paper investigates the sorption characteristics and mechanisms of pyrene onto two types of natural sepiolite-brown (B-Sep) and white (W-Sep). The effects of relevant properties such as clay content, surface area, pore diameter and volume, divalent cations, and organic carbon content were investigated by single component batch adsorption systems. The results suggest that pyrene has high affinity for both sepiolite and its sorption behavior could be mainly affected by exchangeable strongly hydrated cations such as Ca²⁺ and H₂O in the zeolite-like channels and by open channel defects (OCD) structures but no so much by the large number of Si-OH groups located on the sepiolite’s basal surfaces. Mesoporosity rather than surface area largely controls the sorption capacity and intensity of both sepiolites. This is shown by the increase in pore volume that exhibited the greatest increase in BET surface area. Particle size and morphological changes of both sepiolites following pyrene adsorption determined by FE-SEM showed that the sepiolite fibers are much longer than their widths, which are only several laths (several nanometers). This is a result of growth, mostly along the c-axis, at the expense of the diffusion of pyrene molecules through aqueous solution. As a consequence, a significant fibrous morphology is produced following the adsorption of pyrene by both sepiolites.     

Sorption of carbendazim and linuron from aqueous solutions with activated carbon produced from spent coffee grounds: Equilibrium,kinetic and thermodynamic approach

Spent coffee grounds (SCG) have been used for the production of activated carbon (AC) by impregnation with different ratios of phosphoric acid at 600?°C, Xp (H₃PO₄/coffee): 3:1^30%, 4:1^30%, 3:1^50% and 4:1^50%. The obtained AC was characterized by BET, FTIR and SEM. BET surface area corresponds to 803.422 m² g^?1. The influences of the main parameters such as contact time, the pesticides initial concentration, adsorbent dose, pH and temperature on the efficiency of separation process were investigated during the batch operational mode. Results were modeled by adsorption isotherms: Langmuir, Freundlich and Temkin isotherms, which gave satisfactory correlation coefficients. The maximum adsorption capacities calculated from the Langmuir isotherms were 11.918?mg g^?1 for carbendazim and 5.834?mg g^?1 for linuron at room temperature. Adsorption kinetics of carbendazim and linuron have been studied by the pseudo-first-order, the pseudo-second-order and the intraparticle diffusion model. The results of adsorption kinetics have been fitted the best by pseudo-second-order model. The resulted data from FTIR characterization pointed to the presence of many functional groups on the AC surface. SCG adsorbent, as an eco-friendly and low-cost material, showed high potential for the removal of carbendazim and linuron from aqueous solutions.     

稻壳活性炭制备及其对磷的吸附

利用农业废弃物稻壳经炭化、活化、酸洗、水洗和干燥等工艺制备出一种富含微孔和中孔结构的稻壳活性炭,其BET比表面积达886.3 m2/g。通过正交实验优化了稻壳活性炭对磷吸附条件,并在该条件下进行了吸附等温和吸附动力学实验研究。结果表明,稻壳活性炭对磷的吸附等温曲线能较好符合Langmuir模型(R2=0.9284)和Freundlich模型(R2=0.9208),由Langmuir线性拟合方程可得稻壳活性炭对磷饱和吸附量达6.93 mg/g;稻壳活性炭对磷的吸附过程可用准二级动力学方程描述(R2=0.9968),吸附速度较快,颗粒内扩散为该过程控速阶段。稻壳活性炭作为一种易得、廉价、高效的填料,在农村分散型污水生态处理技术中,具有良好的应用前景。     

矸石基X型分子筛对水中Co2+、Cu2+、Cd2+和Cr3+的去除

以煤矸石为原料,采用碱熔后水热合成法制备X型分子筛并进行XRD、SEM、BET和Zeta电位分析。研究其对水中Co2+、Cu2+、Cd2+和Cr3+4种离子的吸附性能,包括吸附等温线、吸附动力学以及初始金属离子浓度、pH值对吸附性能的影响。所合成的矸石基X型分子筛的BET比表面积为676.02 m2/g,微孔孔容为0.263 cm3/g。吸附实验表明,矸石基X型分子筛能有效去除上述4种离子,同时实现煤矸石的资源化和金属离子的去除。4种离子的平衡吸附量均随初始浓度的增大而增大,相同条件下平衡吸附量的大小顺序为Cd2+>Cr3+>Cu2+>Co2+。准二级动力学模型能很好地描述4种离子的吸附动力行为。Langmuir模型对Co2+、Cu2+和Cd2+吸附的拟合较Freundlich模型高,说明其主要表现为物理吸附过程。4种离子的吸附速率均由液膜扩散和颗粒内扩散共同控制。     

活化赤泥的除氟性能

以成本低的铝工业废矿渣（赤泥）为原材料,通过高温煅烧和酸化处理对赤泥进行活化,制备了除氟吸附剂。研究了反应时间、投加量、初始氟浓度、溶液温度、共存阴离子和pH值对活化赤泥除氟效果的影响。结果表明,接触反应时间为18 h时,吸附接近平衡。活化赤泥对氟离子的吸附符合Lagergren二级吸附动力学方程。另外,初始浓度越高,吸附容量越大。与Freundlich相比,Langmuir吸附等温模型可以更好地描述氟离子的吸附特性,最大吸附量可达2.71 mg/g。SO24-、Cl-和NO3-存在时（〈1 000 mg/L）,对氟离子的吸附几乎没有影响,然而,HCO3-、PO34-和氟离子共存时,会对氟吸附造成不利影响。活化赤泥在pH值3.5～11.0时,具有较好的吸附稳定性。活化赤泥是一种吸附容量高、性能稳定的环境友好型除氟材料,具有应用潜力。     

人工湿地基质对 NH+4-N 吸附性能简

为研究建筑废物红砖和工业废物煤渣用作人工湿地脱氮基质的可行性，分别通过静态吸附实验和动态NH₄⁺-N去除效果实验进行考察。结果表明，红砖和煤渣对NH₄⁺-N最大静态吸附量分别为0.2533 mg/g和0.0533 mg/g，其吸附等温曲线均符合Freundlich型吸附方程，吸附常数分别为0.0419和0.0091；红砖煤渣组合对污水中NH₄⁺-N平均动态脱除率达到41.18%，高于红砖的37.63%和煤渣的30.92%。     

Influence of preparation method on structural,optical, magnetic,and adsorption properties of nano-NiFe2O4

Nickel ferrite (NiFe₂O₄) nanoparticles are prepared through different routes (microwave, co-precipitation, and pyrolysis) and tested for water purification applications through adsorption removal of an acid red dye B as a model organic pollutant. The characterizations of the prepared samples were done using XRD, FT-IR, SEM, TEM, BET, UV-Vis absorbance, Raman spectrum, and vibrating sample magnetometer (VSM). All samples showed an inverse spinel crystal structure. The obtained results pointed out to the effect of the synthetic route on the morphology, particle size, optical, and magnetic properties of the prepared ferrites. Magnetic measurements showed super-paramagnetic behavior for all samples. The magnetic saturation (M_s) of the sample prepared by pyrolysis, was found to possess the highest saturation value, 34.8 emu/g. Adsorption experiments were performed under the change in several parameters, such as pH, adsorbent dosage, and initial dye concentration. A dye removal percentage of 99% was reached under the optimum state. The isothermal adsorption of the acid red dye was investigated using several models, in which the experimental data could be best described by the Freundlich model. Several kinetic and equilibrium models were inspected by linear regression analysis and showed best fitting for the adsorption data through pseudo-second-order model. The calculated thermodynamic parameters indicated that the adsorption of acid red dye onto all the ferrite samples is a spontaneous and endothermic physical adsorption process.

     

Adsorptive removal of an acid dye by lignocellulosic waste biomass activated carbon: equilibrium and kinetic studies

Chemically prepared activated carbon material derived from palm flower was used as adsorbent for removal of Amido Black dye in aqueous solution. Batch adsorption studies were performed for the removal of Amido Black 10B (AB10B), a di-azo acid dye from aqueous solutions by varying the parameters like initial solution pH, adsorbent dosage, initial dye concentration and temperature with three different particle sizes such as 100 μm, 600 μm and 1000 μm. The zero point charge was pH 2.5 and the maximum adsorption occurred at the pH 2.3. Experimental data were analyzed by model equations such as Langmuir, Freundlich and Temkin isotherms and it was found that the Freundlich isotherm model best fitted the adsorption data and the Freundlich constants varied from (K_F) 1.214, 1.077 and 0.884 for the three mesh sizes. Thermodynamic parameters such as ΔG, ΔH and ΔS were also calculated for the adsorption processes and found that the adsorption process is feasible and it was the endothermic reaction. Adsorption kinetics was determined using pseudo first-order, pseudo second-order rate equations and also Elovich model and intraparticle diffusion models. The results clearly showed that the adsorption of AB10B onto lignocellulosic waste biomass from palm flower (LCBPF) followed pseudo second-order model, and the pseudo second-order rate constants varied from 0.059 to 0.006 (g mg⁻¹ min) by varying initial adsorbate concentration from 25 mg L⁻¹ to 100 mg L⁻¹. Analysis of the adsorption data confirmed that the adsorption process not only followed intraparticle diffusion but also by the film diffusion mechanism.