Temporal characteristics from continuous measurements of PM2.5 and speciation at the Taipei Aerosol Supersite from 2002 to 2008

This study uses monitoring data collected at the Taipei Aerosol Supersite from March 2002 to February 2008 to analyze characteristics such as seasonal fluctuations, diurnal variations, and photochemical-related variations of PM_2.5 chemical compositions. The results indicate that the average of PM_2.5 mass concentration in Taipei during this period is 30.3 ± 16.0 μg m^?3. The highest average concentration of PM_2.5 components is that of sulfate, which accounts for 21.1% of the PM_2.5 mass, followed by organic carbon (OC) at 15.9%, nitrate at 5.8%, and elemental carbon (EC) at 5.4%. Concentrations of EC, OC, and nitrate have distinctive but similar seasonal fluctuations, which is highest in spring and lowest in fall. Sulfate concentration has less seasonal fluctuations, and the highest value appears during the fall. Similarly, concentrations of EC, OC, and nitrate have notable diurnal variations; however, the diurnal variation of sulfate concentration is not very apparent. These observation data show that EC, OC, and nitrate in PM_2.5 in the Taipei metropolis come mainly from local emissions, while sulfate comes mainly from the regional transport of pollutants. This is likely because Taiwan is located on the lee zone of the Asian prevailing winds from fall to spring; its air quality is frequently affected by the transport of air pollutants from Mainland China. In addition, the extent of increase in aerosols is much higher than that of CO, indicating the formation of secondary aerosol when photochemical activity is strong. Based on six years of observation data, this study explores three potential scenarios to set up Taiwan's PM_2.5 air quality standard (AQS). The analysis indicates that the optimum standard for 24-h air quality of PM_2.5 should be around 50 μg m^?3.     

Characterization of Particulate Matter for Three Sites in Kuwait

Abstract

Many studies have shown strong associations between particulate matter (PM) levels and a variety of health outcomes, leading to changes in air quality standards in many regions, especially the United States and Europe. Kuwait, a desert country located on the Persian Gulf, has a large petroleum industry with associated industrial and urban land uses. It was marked by environmental destruction from the 1990 Iraqi invasion and subsequent oil fires. A detailed particle characterization study was conducted over 12 months in 2004–2005 at three sites simultaneously with an additional 6 months at one of the sites. Two sites were in urban areas (central and southern) and one in a remote desert location (northern). This paper reports the concentrations of particles less than 10 µm in diameter (PM₁₀) and fine PM (PM_2.5), as well as fine particle nitrate, sulfate, elemental carbon (EC), organic carbon (OC), and elements measured at the three sites. Mean annual concentrations for PM₁₀ ranged from 66 to 93 µg/m³ across the three sites, exceeding the World Health Organization (WHO) air quality guidelines for PM₁₀ of 20 µg/m³. The arithmetic mean PM_2.5 concentrations varied from 38 and 37 µg/m³ at the central and southern sites, respectively, to 31 µg/m³ at the northern site. All sites had mean PM_2.5 concentrations more than double the U.S. National Ambient Air Quality Standard (NAAQS) for PM_2.5. Coarse particles comprised 50–60% of PM₁₀. The high levels of PM₁₀ and large fraction of coarse particles comprising PM₁₀ are partially explained by the resuspension of dust and soil from the desert crust. However, EC, OC, and most of the elements were significantly higher at the urbanized sites, compared with the more remote northern site, indicating significant pollutant contributions from local mobile and stationary sources. The particulate levels in this study are high enough to generate substantial health impacts and present opportunities for improving public health by reducing airborne PM.     

Characterization of carbonaceous species in PM2.5 in Xi'an during spring

The characterization of carbonaceous species in PM_2.5 during a spring period in a suburb of Xi'an, China was investigated. PM_2.5 samples were collected on quartz filters and analyzed for organic carbon (OC) and elemental carbon (EC). The thermal optical reflectance method was used. The minimum OC/EC ratio method was used to estimate the concentration of secondary organic carbon (SOC). The distribution of eight carbon fractions was investigated as well. The average mass concentrations of OC and EC were 15.90 and 8.38 μg/m³, respectively. The average OC/EC ratio ranged from 1.16 to 3.16 with an average value of 2.25. This implies the existence of SOC in PM_2.5. The mean SOC concentration was 7.20 μg/m³, accounting for 45.28% of total OC. This result suggests that SOC is a significant component of OC in the suburb of Xi'an. Results from the distribution of eight carbon fractions revealed that emissions from motor vehicle, coal combustion, and road dust were the main source of carbonaceous particles in the sampling period.     

Fugitive Dust Emission Source Profiles and Assessment of Selected Control Strategies for Particulate Matter at Gravel Processing Sites in Taiwan

Abstract

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM₁₀), fine suspended particulate (PM_2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (<100 µm) concentrations at the boundary of gravel sites ranged from 280 to 1290 µg/m³, which clearly exceeds the Taiwan hourly air quality standard of 500 µg/m³. Moreover, PM₁₀ concentrations, ranging from 135 to 550 µg/m³, were also above the daily air quality standard of 125 µg/m³ and approximately 1.2 and 1.5 times the PM_2.5 concentrations, ranging from 105 to 470 µg/m³. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 µm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Source Identification and Trends in Concentrations of Gaseous and Fine Particulate Principal Species in Seoul,South Korea

Abstract

Ambient measurements were made using two sets of annular denuder system during the four seasons (April 2001 to February 2002) and were then compared with the results during the period of 1996–1997 to estimate the trends and seasonal variations in concentrations of gaseous and fine particulate matter (PM_2.5) principal species. Annual averages of gaseous HNO₃ and NH₃ increased by 11% and 6%, respectively, compared with those of the previous study, whereas HONO and SO₂ decreased by 11% and 136%, respectively. The PM_2.5 concentration decreased by ～17%, 35% for SO₄ ^2?, and 29% for NH₄ ⁺, whereas NO₃ ^? increased by 21%. Organic carbon (OC) and elemental carbon (EC) were 12.8 and 5.98 μg/m^-3, accounting for ～26 and 12% of PM_2.5 concentration, respectively. The species studied accounted for 84% of PM_2.5 concentration, ranging from 76% in winter to 97% in summer.

Potential source contribution function (PSCF) analysis was used to identify possible source areas affecting air pollution levels at a receptor site in Seoul. High possible source areas in concentrations of PM_2.5, NO₃ ^?, SO₄ ^2?, NH₄ ⁺, and K⁺ were coastal cities of Liaoning province (possibly emissions from oil-fired boilers on ocean liners and fishing vessels and industrial emissions), inland areas of Heibei/Shandong provinces (the highest density areas of agricultural production and population) in China, and typical port cities (Mokpo, Yeosu, and Busan) of South Korea. In the PSCF map for OC, high possible source areas were also coastal cities of Liaoning province and inland areas of Heibei/Shandong provinces in China. In contrast, high possible source areas of EC were highlighted in the south of the Yellow Sea, indicating possible emissions from oil-fired boilers on large ships between South Korea and Southeast Asia. In summary, the PSCF results may suggest that air pollution levels in Seoul are affected considerably by long-range transport from external areas, such as the coastal zone in China and other cities in South Korea, as well as Seoul itself.     

Particulates and Metallic Elements Monitoring at Two Sampling Sites (Harbor,Airport) in Taiwan

This study characterized the dry deposition flux and dry deposition velocity (Vd) of metallic elements attached on particulate matter. Specifically, large particles (>10 μm), coarse particles (10 μm～2.5 μm), and fine particles (<2.5 μm) were studied at the Gong Ming Junior High School (Taichung Airport) and Taichung Harbor sampling sites in central Taiwan. Ambient air samples were collected to determine total suspended particulate matter (TSP), dry deposition plate (DDP), Vd, coarse particulate matter (PM_2.5–10) and fine particulate matter (PM_2.5), and metallic elements concentrations at the Airport and Taichung Harbor sites between June 17, 2013, and November 14, 2013. The results revealed that the average TSP, DDP, Vd, PM_2.5–10, and PM_2.5 particulate at the Airport were 54.55 (μg/m³), 902.25 (μg/m²-min), 17.11 (m/sec), 0.003 (μg/m³), and 0.010 (μg/m³), respectively; while these values at Taichung Harbor were 63.66 (μg/m³), 539.69 (μg/m²-min), 9.94 (m/sec), 0.003 (μg/m³), and 0.014 (μg/m³), respectively. In addition, the results showed that the average Cu and Pb concentrations were higher than Cr, Ni, and Cd for both the airport and harbor sampling sites. Furthermore, Cr, N, Cu, Cd, and Pb had the highest average concentrations versus those reported for other study areas, with one exception: The results obtained in Kacanik, Kosovo, during 2005. The average metallic elements concentrations order was Cu > Pb > Cr > Ni > Cd.     

Air Quality Impact of the Coal-Fired Power Plants in the Northern Passageway of the China West-East Power Transmission Project

Abstract

This paper analyzes the air quality impacts of coal-fired power plants in the northern passageway of the West-East Power Transmission Project in China. A three-layer Lagrangian model called ATMOS, was used to simulate the spatial distribution of incremental sulfur dioxide (SO₂) and coarse particulate matter (PM₁₀) concentrations under different emission control scenarios. In the year 2005, the emissions from planned power plants mainly affected the air quality of Shanxi, Shaanxi, the common boundary of Inner Mongolia and Shanxi, and the area around the boundary between Inner Mongolia and Ningxia. In these areas, the annually averaged incremental SO₂ and PM₁₀ concentrations exceed 2 and 2.5 µg/m3, respectively. The maximum increases of the annually averaged SO₂ and PM₁₀ concentrations are 8.3 and 7.2 µg/m³, respectively, which occur around Hancheng city, near the boundary of the Shaanxi and Shanxi provinces. After integrated control measures are considered, the maximum increases of annually averaged SO₂ and PM₁₀ concentrations fall to 4.9 and 4 µg/m³, respectively. In the year 2010, the areas affected by planned power plants are mainly North Shaanxi, North Ningxia, and Northwest Shanxi. The maximum increases of the annually averaged SO₂ and PM₁₀ concentrations are, respectively, 6.3 and 5.6 µg/m³, occurring in Northwest Shanxi, which decline to 4.4 and 4.1 µg/m³ after the control measures are implemented. The results showed that the proposed power plants mainly affect the air quality of the region where the power plants are built, with little impact on East China where the electricity will be used. The influences of planned power plants on air quality will be decreased greatly by implementing integrated control measures.     

Applications of GPS-tracked personal and fixed-location PM2.5 continuous exposure monitoring

Continued development of personal air pollution monitors is rapidly improving government and research capabilities for data collection. In this study, we tested the feasibility of using GPS-enabled personal exposure monitors to collect personal exposure readings and short-term daily PM_2.5 measures at 15 fixed locations throughout a community. The goals were to determine the accuracy of fixed-location monitoring for approximating individual exposures compared to a centralized outdoor air pollution monitor, and to test the utility of two different personal monitors, the RTI MicroPEM V3.2 and TSI SidePak AM510. For personal samples, 24-hr mean PM_2.5 concentrations were 6.93 μg/m³ (stderr = 0.15) and 8.47 μg/m³ (stderr = 0.10) for the MicroPEM and SidePak, respectively. Based on time–activity patterns from participant journals, exposures were highest while participants were outdoors (MicroPEM = 7.61 µg/m³, stderr = 1.08, SidePak = 11.85 µg/m³, stderr = 0.83) or in restaurants (MicroPEM = 7.48 µg/m³, stderr = 0.39, SidePak = 24.93 µg/m³, stderr = 0.82), and lowest when participants were exercising indoors (MicroPEM = 4.78 µg/m³, stderr = 0.23, SidePak = 5.63 µg/m³, stderr = 0.08). Mean PM_2.5 at the 15 fixed locations, as measured by the SidePak, ranged from 4.71 µg/m³ (stderr = 0.23) to 12.38 µg/m³ (stderr = 0.45). By comparison, mean 24-h PM_2.5 measured at the centralized outdoor monitor ranged from 2.7 to 6.7 µg/m³ during the study period. The range of average PM_2.5 exposure levels estimated for each participant using the interpolated fixed-location data was 2.83 to 19.26 µg/m³ (mean = 8.3, stderr = 1.4). These estimated levels were compared with average exposure from personal samples. The fixed-location monitoring strategy was useful in identifying high air pollution microclimates throughout the county. For 7 of 10 subjects, the fixed-location monitoring strategy more closely approximated individuals’ 24-hr breathing zone exposures than did the centralized outdoor monitor. Highlights are: Individual PM_2.5 exposure levels vary extensively by activity, location and time of day; fixed-location sampling more closely approximated individual exposures than a centralized outdoor monitor; and small, personal exposure monitors provide added utility for individuals, researchers, and public health professionals seeking to more accurately identify air pollution microclimates.

Implications: Personal air pollution monitoring technology is advancing rapidly. Currently, personal monitors are primarily used in research settings, but could they also support government networks of centralized outdoor monitors? In this study, we found differences in performance and practicality for two personal monitors in different monitoring scenarios. We also found that personal monitors used to collect outdoor area samples were effective at finding pollution microclimates, and more closely approximated actual individual exposure than a central monitor. Though more research is needed, there is strong potential that personal exposure monitors can improve existing monitoring networks.     

Concentrations of aliphatic and polycyclic aromatic hydrocarbons in ambient PM2.5 and PM10 particulates in Doha,Qatar

Organic carbon (OC), elemental carbon (EC), and 90 organic compounds (36 polycyclic aromatic hydrocarbons [PAHs], 25 n-alkane homologues, 17 hopanes, and 12 steranes) were concurrently quantified in atmospheric particulate matter of PM_2.5 and PM₁₀. The 24-hr PM samples were collected using Harvard Impactors at a suburban site in Doha, Qatar, from May to December 2015. The mass concentrations (mean ± standard deviation) of PM_2.5 and PM₁₀ were 40 ± 15 and 145 ± 70 µg m^?3, respectively, exceeding the World Health Organization (WHO) air quality guidelines. Coarse particles comprised 70% of PM₁₀. Total carbonaceous contents accounted for 14% of PM_2.5 and 10% of PM₁₀ particulate mass. The major fraction (90%) of EC was associated with the PM_2.5. In contrast, 70% of OC content was found in the PM_2.5–10 fraction. The secondary OC accounted for 60–68% of the total OC in both PM fractions, indicating photochemical conversions of organics are much active in the area due to higher air temperatures and solar radiations. Among the studied compounds, n-alkanes were the most abundant group, followed by PAHs, hopanes, and steranes. n-Alkanes from C₂₅ to C₃₅ prevailed with a predominance of odd carbon numbered congeners (C₂₇–C₃₁). High-molecular-weight PAHs (5–6 rings) also prevailed, within their class, with benzo[b + j]fluoranthene (Bb + jF) being the dominant member. PAHs were mainly (80%) associated with the PM_2.5 fraction. Local vehicular and fugitive emissions were predominant during low-speed southeasterly winds from urban areas, while remote petrogenic/biogenic emissions were particularly significant under prevailing northwesterly wind conditions.

Implications: An unprecedented study in Qatar established concentration profiles of EC, OC, and 90 organic compounds in PM_2.5 and PM₁₀. Multiple tracer organic compounds for each source can be used for convincing source apportionment. Particle concentrations exceeded WHO air quality guidelines for 82–96% of the time, revealing a severe problem of atmospheric PM in Doha. Dominance of EC and PAHs in fine particles signifies contributions from combustion sources. Dependence of pollutants concentrations on wind speed and direction suggests their significant temporal and spatial variability, indicating opportunities for improving the air quality by identifying sources of airborne contaminants.     

Particulate Matter in California: Part 2—Spatial,Temporal, and Compositional Patterns of PM2.5, PM10–2.5, and PM10

Abstract

Geographic and temporal variations in the concentration and composition of particulate matter (PM) provide important insights into particle sources, atmospheric processes that influence particle formation, and PM management strategies. In the nonurban areas of California, annual-average PM_2.5 and PM₁₀ concentrations range from 3 to 10 [H9262]g/m³ and from 5 to 18 µg/m³, respectively. In the urban areas of California, annual-averages for PM_2.5 range from 7 to 30 [H9262]g/m³, with observed 24-hr peaks reaching levels as high as 160 [H9262]g/m³. Within each air basin, exceedances are a mixture of isolated events as well as periods of elevated PM_2.5 concentrations that are more prolonged and regional in nature. PM_2.5 concentrations are generally highest during the winter months. The exception is the South Coast Air Basin, where fairly high values occur throughout the year. Annual-average PM_2.5 mass, as well as the concentrations of major components, declined from 1988 to 2000. The declines are especially pronounced for the sulfate (SO₄ ^2?) and nitrate (NO₃ ^?) components of PM_2.5 and PM₁₀ and correlate with reductions in ambient levels of oxides of sulfur (SO_x) and oxides of nitrogen (NO_x). Annual averages for PM_10–2.5 and PM₁₀ exhibited similar downwind trends from 1994 to 1999, with a slightly less pronounced decrease in the coarse fraction.     

Chemical characteristics of principal PM2.5 species in Chongju,South Korea

Fine particles were collected over four seasons from October 1995 to August 1996 to evaluate the chemical characteristics of principal PM_2.5 components in Chongju, South Korea. The annual mean concentrations of PM_2.5 (d_p⩽2.5 μm), sulfate, nitrate, ammonium, elemental carbon (EC) and organic carbon (OC) were 44.2, 8.22, 3.63, 2.84, 4.44 and 4.99 μg m⁻³, respectively. The sum of the species measured from this study accounted for 50–62% of the PM_2.5 mass. Sulfate was the most abundant species and constituted 13–23% of the PM_2.5 mass. The EC and OC accounted for 17–28% of PM_2.5. The correlation between OC and EC was strong, and the annual mean ratio of OC/EC was 1.12, suggesting that OC measured in the Chongju area may be emitted directly in particulate form as a primary aerosol.     

Organic and elemental carbon associated to PM10 and PM2.5 at urban sites of northern Greece

Organic carbon (OC) and elemental carbon (EC) concentrations, associated to PM₁₀ and PM_2.5 particle fractions, were concurrently determined during the warm and the cold months of the year (July–September 2011 and February–April 2012, respectively) at two urban sites in the city of Thessaloniki, northern Greece, an urban-traffic site (UT) and an urban-background site (UB). Concentrations at the UT site (11.3?±?5.0 and 8.44?±?4.08 14 μg m^?3 for OC₁₀ and OC_2.5 vs. 6.56?±?2.14 and 5.29?±?1.54 μg m^?3 for EC₁₀ and EC_2.5) were among the highest values reported for urban sites in European cities. Significantly lower concentrations were found at the UB site for both carbonaceous species, particularly for EC (6.62?±?4.59 and 5.72?±?4.36 μg m^?3 for OC₁₀ and OC_2.5 vs. 0.93?±?0.61 and 0.69?±?0.39 μg m^?3 for EC₁₀ and EC_2.5). Despite that, a negative UT-UB increment was frequently evidenced for OC_2.5 and PM_2.5 in the cold months possibly indicative of emissions from residential wood burning at the urban-background site. At both sites, cconcentrations of OC fractions were significantly higher in the cold months; on the contrary, EC fractions at the UT site were prominent in the warm season suggesting some influence from maritime emissions in the nearby harbor area. Secondary organic carbon, being estimated using the EC tracer method and seasonally minimum OC/EC ratios, was found to be an appreciable component of particle mass particularly in the cold season. The calculated secondary contributions to OC ranged between 35 and 59 % in the PM₁₀ fraction, with relatively higher values in the PM_2.5 fraction (39–61 %). The source origin of carbonaceous species was investigated by means of air parcel back trajectories, satellite fire maps, and concentration roses. A local origin was mainly concluded for OC and EC with limited possibility for long range transport of biomass (agricultural waste) burning aerosol.     

Intercomparison of two different thermal-optical elemental carbons and optical black carbon during ABC-EAREX2005

A formal intercomparison of fine particle elemental (black) carbon is conducted involving three real-time semi-continuous measurement systems. Two-hourly interval time-resolved measurements of organic carbon (OC) and elemental carbon (EC) were performed at the Gosan site, Korea during Atmospheric Brown Clouds–East Asian Regional Experiment 2005 (ABC-EAREX2005) campaign. They were operated by the same semi-continuous field carbon instruments of Sunset Laboratory (thermal optical transmittance) in PM_2.5 particulate. However, their thermal protocols (four and two steps for OC and five and two steps for EC) were different. The co-located 1 min black carbon (BC) concentrations were compared by an Aethalometer for an intercomparison study.As a result, the poor R² of OC between two different temperature protocols suggested that OC can be significantly more biased by the slight differences of maximum temperature (870 and 840 °C) and a number of temperature steps (four steps and two steps) with their hold times. However, EC that is a smaller fraction of total carbon (TC) shows the good agreement between two different protocols, which are under a mixture of 2% O₂ and 98% He in six temperature steps and two temperature steps as max as 900 and 880 °C with the slope of 1.05±0.15 (R² of 0.98). The different slopes between EC and BC, which show the range of 1.23–1.61, demonstrate the variability of the attenuation coefficient of the BC particulate.     

Sources and characteristics of carbonaceous aerosols at Agra “World heritage site” and Delhi “capital city of India”

Agra, one of the oldest cities “World Heritage site”, and Delhi, the capital city of India are both located in the border of Indo-Gangetic Plains (IGP) and heavily loaded with atmospheric aerosols due to tourist place, anthropogenic activities, and its topography, respectively. Therefore, there is need for monitoring of atmospheric aerosols to perceive the scenario and effects of particles over northern part of India. The present study was carried out at Agra (AGR) as well as Delhi (DEL) during winter period from November 2011 to February 2012 of fine particulate (PM_2.5: d?<?2.5 μm) as well as associated carbonaceous aerosols. PM_2.5 was collected at both places using medium volume air sampler (offline measurement) and analyzed for organic carbon (OC) and elemental carbon (EC). Also, simultaneously, black carbon (BC) was measured (online) at DEL. The average mass concentration of PM_2.5 was 165.42?±?119.46 μg m^?3 at AGR while at DEL it was 211.67?±?41.94 μg m^?3 which is ~27 % higher at DEL than AGR whereas the BC mass concentration was 10.60 μg m^?3. The PM_2.5 was substantially higher than the annual standard stipulated by central pollution control board and United States Environmental Protection Agency standards. The average concentrations of OC and EC were 69.96?±?34.42 and 9.53?±?7.27 μm m^?3, respectively. Total carbon (TC) was 79.01?±?38.98 μg m^?3 at AGR, while it was 50.11?±?11.93 (OC), 10.67?±?3.56 μg m^?3 (EC), and 60.78?±?14.56 μg m^?3 (TC) at DEL. The OC/EC ratio was 13.75 at (AGR) and 5.45 at (DEL). The higher OC/EC ratio at Agra indicates that the formation of secondary organic aerosol which emitted from variable primary sources. Significant correlation between PM_2.5 and its carbonaceous species were observed indicating similarity in sources at both sites. The average concentrations of secondary organic carbon (SOC) and primary organic carbon (POC) at AGR were 48.16 and 26.52 μg m^?3 while at DEL it was 38.78 and 27.55 μg m^?3, respectively. In the case of POC, similar concentrations were observed at both places but in the case of SOC higher over AGR by 24 in comparison to DEL, it is due to the high concentration of OC over AGR. Secondary organic aerosol (SOA) was 42 % higher at AGR than DEL which confirms the formation of secondary aerosol at AGR due to rural environment with higher concentrations of coarse mode particles. The SOA contribution in PM_2.5 was also estimated and was ~32 and 12 % at AGR and DEL respectively. Being high loading of fine particles along with carbonaceous aerosol, it is suggested to take necessary and immediate action in mitigation of the emission of carbonaceous aerosol in the northern part of India.     

Urban impacts on regional carbonaceous aerosols: Case study in central Texas

Rural and background sites provide valuable information on the concentration and optical properties of organic, elemental, and water-soluble organic carbon (OC, EC, and WSOC), which are relevant for understanding the climate forcing potential of regional atmospheric aerosols. To quantify climate- and air quality-relevant characteristics of carbonaceous aerosol in the central United States, a regional background site in central Texas was chosen for long-term measurement. Back trajectory (BT) analysis, ambient OC, EC, and WSOC concentrations and absorption parameters are reported for the first 15 months of a long-term campaign (May 2011–August 2012). BT analysis indicates consistent north–south airflow connecting central Texas to the Central Plains. Central Texas aerosols exhibited seasonal trends with increased fine particulate matter (<2.5 μm aerodynamic diameter, PM_2.5) and OC during the summer (PM_2.5 = 10.9 μg m^?3 and OC = 3.0 μg m^?3) and elevated EC during the winter (0.22 μg m^?3). When compared to measurements in Dallas and Houston, TX, central Texas OC appears to have mixed urban and rural sources. However, central Texas EC appears to be dominated by transport of urban emissions. WSOC averaged 63% of the annual OC, with little seasonal variability in this ratio. To monitor brown carbon (BrC), absorption was measured for the aqueous WSOC extracts. Light absorption coefficients for EC and BrC were highest during summer (EC MAC = 11 m² g^?1 and BRC MAE₃₆₅ = 0.15 m² g^?1). Results from optical analysis indicate that regional aerosol absorption is mostly due to EC with summertime peaks in BrC attenuation. This study represents the first reported values of WSOC absorption, MAE₃₆₅, for the central United States.

Implications:Background concentration and absorption measurements are essential in determining regional potential radiative forcing due to atmospheric aerosols. Back trajectory, chemical, and optical analysis of PM_2.5 was used to determine climatic and air quality implications of urban outflow to a regional receptor site, representative of the central United States. Results indicate that central Texas organic carbon has mixed urban and rural sources, while elemental carbon is controlled by the transport of urban emissions. Analysis of aerosol absorption showed black carbon as the dominant absorber, with less brown carbon absorption than regional studies in California and the southeastern United States.     

Prescribed Burns and Wildfires in Colorado: Impacts of Mitigation Measures on Indoor Air Particulate Matter

Abstract

Wildfires and prescribed burns are receiving increasing attention as sources of fine particulate matter (PM_2.5). The goal of this research project was to understand the impact of mitigation strategies for residences impacted by scheduled prescribed burns and wildfires. Pairs of residences were solicited to have PM_2.5 concentrations monitored inside and outside of their houses during four fires. The effect of using air cleaners on indoor PM_2.5 was investigated, as well as the effect of keeping windows closed. Appropriately sized air cleaners were provided to one of each pair of residences; occupants of all of the residences were asked to keep windows shut and minimize opening of exterior doors. Additionally, residents were asked to record all of the activities that may be a source of particulate matter, such as cooking and cleaning. Measurements were made during one prescribed burn and three wildfires during the 2002 fire season. Outdoor 24‐hr average PM_2.5 concentrations ranging from 6 to 38 µg/m³ were measured during the fires, compared with levels of 2–5 µg/m³ during background measurements when no fires were burning. During the fires, PM_2.5 was <3 µg/m³ inside all of the houses with air cleaners installed. This corresponds with a decrease of 63–88% in homes with the air cleaners operating when compared with homes without air cleaners. In the homes without the air cleaners, measured indoor concentrations were 58–100% of the concentrations measured outdoors.     

Considering the effects of ambient particulate matter on the lung function of motorcycle taxi drivers in Bangkok,Thailand

The motorcycle taxi drivers of Bangkok have been heavily exposed to high concentrations of PM₁₀ (particulate matter with an aerodynamic diameter ≤10 μm), and the impact of this on their lungs has been neither documented nor studied. This study examines the association between exposure to PM₁₀ and lung function decline among motorcycle taxi drivers. A cross-sectional study was conducted in Bangkok between two groups: a subject group of motorcycle taxi drivers and control group of enclosed vehicle taxi drivers. The findings of the Thailand Pollution Control Department were used to estimate the annual ambient PM₁₀ concentration levels in the metropolis. Pulmonary functions of motorcycle taxi drivers and enclosed vehicle taxi drivers were measured and compared using the Mann-Whitney test. Multiple linear regression analysis was applied to estimate the effects of PM₁₀ exposure on the lung function of motorcycle taxi drivers. A total of 1283 motorcycle taxi drivers and 600 taxi drivers were investigated. The mean forced expiratory volume in 1 sec/forced vital capacity (FEV₁/FVC) of the motorcycle taxi drivers was significantly lower than that of the taxi drivers (P < 0.001). The mean FEV₁/FVC of motorcycle taxi drivers exposed to ≥50 µg/m³ PM₁₀ was statistically lower (?2.82%; 95% confidence interval [CI]: ?4.54% to ?1.09%) and the mean % vital capacity (%VC) of those exposed to 40–49.9 µg/m³ PM₁₀ was statistically lower than that of motorcycle taxi drivers exposed to <30 µg/m³ PM₁₀ (?3.33%; 95% CI: ?5.79% to ?0.87%). Motorcycle taxi drivers were directly exposed to air pollution in their working environment. As a result, their lung function might decrease more than that of enclosed vehicle taxi drivers. With the possible exposure to ≥50 µg/m³ PM₁₀, the vehicular emission standards should be vigorously enforced. Further investigation is warranted to clarify the effect of lung dysfunction on the work and lifestyle of motorcycle taxi drivers.

Implications: Motorcycle taxi drivers are directly exposed to air pollution in their work environment; therefore, their lung function might decrease more than that of enclosed vehicle taxi drivers, especially when exposed to ≥50 µg/m³ PM₁₀. World Health Organization (WHO) vehicular emission standards should be recognized and eventually enforced.     

The Impact of a Building Implosion on Airborne Particulate Matter in an Urban Community

Abstract

In response to community concerns, the air quality impact of imploding a 22-story building in east Baltimore, MD, was studied. Time- and space-resolved concentrations of indoor and outdoor particulate matter (PM) (nominally 0.5–10 µm) were measured using a portable nephelometer at seven and four locations, respectively. PM₁₀ levels varied in time and space; there was no measurable effect observed upwind of the implosion. The downwind peak PM₁₀ levels varied with distance (54,000–589 µg/m³) exceeding pre-implosion levels for sites 100 and 1130 m 3000- and 20-fold, respectively. Estimated outdoor 24-hr integrated mass concentrations varied from 15 to 72 µg/m³. The implosion did not result in the U.S. Environmental Protection Agency (EPA) National Ambient Air Quality Standard (NAAQS) for PM₁₀ being exceeded. X-ray fluorescence analysis indicated that the elemental composition was dominated by crustal elements: calcium (57%), silicon (23%), aluminum (7.6%), and iron (6.1%). Lead was above background but at a low level (0.17 µg/m³). Peak PM₁₀ concentrations were short-lived; most sites returned to background within 15 min. No increase in indoor PM₁₀ was observed even at the most proximate 250 m location. These results demonstrate that a building implosion can have a severe but short-lived impact on community air quality. Effective protection is offered by being indoors or upwind.     

Roadside Particulate Air Pollution in Bangkok

Abstract

Airborne fine particles of PM_2.5-10 and PM_2.5 in Bangkok, Nonthaburi, and Ayutthaya were measured from December 22, 1998, to March 26, 1999, and from November 30, 1999, to December 2, 1999. Almost all the PM₁₀ values in the high-polluted (H) area exceeded the Thailand National Ambient Air Quality Standards (NAAQS) of 120 μg/m³. The low-polluted (L) area showed low PM₁₀ (34–74 μg/m³ in the daytime and 54–89 μg/m³ at night). PM_2.5 in the H area varied between 82 and 143 μg/m³ in the daytime and between 45 and 146 μg/m³ at night. In the L area, PM_2.5 was quite low both day and night and varied between 24 and 54 μg/m³, lower than the U.S. Environmental Protection Agency (EPA) standard (65 μg/m³). The personal exposure results showed a significantly higher proportion of PM_2.5 to PM₁₀ in the H area than in the L area (H = 0.80 ± 0.08 and L = 0.65 ± 0.04).

Roadside PM₁₀ was measured simultaneously with the Thailand Pollution Control Department (PCD) monitoring station at the same site and at the intersections where police work. The result from dual simultaneous measurements of PM₁₀ showed a good correlation (correlation coefficient: r = 0.93); however, PM levels near the roadside at the intersections were higher than the concentrations at the monitoring station. The relationship between ambient PM level and actual personal exposures was examined. Correlation coefficients between the general ambient outdoors and personal exposure levels were 0.92 for both PM_2.5 and PM₁₀.

Bangkok air quality data for 1997–2000, including 24-hr average PM₁₀, NO₂, SO₂, and O₃ from eight PCD monitoring stations, were analyzed and validated. The annual arithmetic mean PM₁₀ of the PCD data at the roadside monitoring stations for the last 3 years decreased from 130 to 73 μg/m³, whereas the corresponding levels at the general monitoring stations decreased from 90 to 49 μg/m³. The proportion of days when the level of the 24-hr average PM₁₀ exceeded the NAAQS was between 13 and 26% at roadside stations. PCD data showed PM₁₀ was well correlated with NO₂ but not with SO₂, suggesting that automobile exhaust is the main source of the particulate air pollution. The results obtained from the simultaneous measurement of PM_2.5 and PM₁₀ indicate the potential environmental health hazard of fine particles. In conclusion, Bangkok traffic police were exposed to high levels of automobile-derived particulate air pollution.     

Optical and thermal characteristics of carbonaceous aerosols measured at an urban site in Gwangju,Korea, in the winter of 2011

Carbonaceous components (organic carbon [OC] and elemental carbon [EC]) and optical properties (light absorption and scattering) of fine particulate matter (aerodynamic diameter <2.5 μm; PM_2.5) were simultaneously measured at an urban site in Gwangju, Korea, during the winter of 2011. OC was further classified into OC1, OC2, OC3, and OC4, based on a temperature protocol using a Sunset OC/EC analyzer. The average OC and EC concentrations were 5.0 ± 2.5 and 1.7 ± 0.9 μg C m^?3, respectively. The average single-scattering albedo (SSA) at a wavelength of 550 nm was 0.58 ± 0.11, suggesting that the aerosols observed in the winter of 2011 had a local warming effect in this area. During the whole sampling period, “stagnant PM” and “long-range transport PM” events were identified. The light absorption coefficient (b_abs) was higher during the stagnant PM event than during the long-range transport PM event due to the existence of abundant light-absorbing OC during the stagnant PM event. In particular, the OC2 and OC3 concentrations were higher during the stagnant PM event than those during the long-range transport event, suggesting that OC2 and OC3 might be more related to the light-absorbing OC. The light scattering coefficient (b_scat) was similar between the events. On average, the mass absorption efficiency attributed to EC (σ_EC) was 9.6 m² g^?1, whereas the efficiency attributed to OC (σ_OC) was 1.8 m² g^?1 at λ = 550 nm. Furthermore, the σ_EC is comparable among the PM event days, but the σ_OC for the stagnant PM event was significantly higher than that for the long-range transport PM event (1.7 vs. 0.5).

Implications: Optical and thermal properties of carbonaceous aerosol were measured at Gwangju, and carbonaceous aerosol concentration and optical property varied between “stagnant PM” and “long-range transport PM” events. More abundant light absorbing OC was observed during the stagnant PM event.