Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Patterns of volatile metabolites and nonvolatile trichothecenes produced by isolates of <Emphasis Type="Italic">Stachybotrys,Fusarium, Trichoderma,Trichothecium</Emphasis> and <Emphasis Type="Italic">Memnoniella</Emphasis>

We reported previously that trichodiene, a volatile trichothecene derivative, was produced by a Stachybotrys isolate, also known to produce highly cytotoxic, non-volatile, macrocyclic trichothecenes (satrotoxins). We investigated the relationship between the production of trichodiene and various non-volatile trichothecenes for several molds. Volatile metabolites were concentrated by adsorption on Tenax TA and analyzed by GC/MS, while non-volatile metabolites were separated by HPLC, derivatized and analyzed by GC/MS. Stachybotrys chartarum isolates producing macrocyclic trichothecenes secreted significantly larger amounts of trichodiene and other sesquiterpenes than isolates which only produced simple trichothecenes. The amounts of secreted trichodiene were relatively small in all cases. With the exception of Memnoniella, which excreted small amounts of sesquiterpenes, the other isolates produced varying amounts of sesquiterpenes, including trichodiene, as well as simple tricothecenes, no detectable trichodiene, but large amounts of griseofulvin derivatives. In Stachybotrys there is apparently a correlation between trichodiene and macrocyclic trichothecene production. In the remaining isolates, there was no simple relationship between trichodiene and non-volatile trichothecene synthesis. Trichodiene is produced in larger amounts by Stachybotrys isolates, which also produce satratoxins, but it will be difficult to utilize this metabolite to detect toxic isolates in buildings due to the relatively small amounts excreted.     

Knowledge transfer initiative between molecular biologists and environmental researchers and regulators

A Natural Environment Research Council (NERC) funded Knowledge Transfer (KT) workshop was held in the United Kingdom (UK) to identify the needs and opportunities in the application of molecular biology and ‘omics’ techniques to environmental monitoring and risk assessment. Attendees highlighted a lack of effective communication between end-users and researchers as well as difficulties with data interpretation as reasons behind the slow uptake of molecular biology and omics techniques. A number of promising areas in which new techniques could be implemented at a practical level in the very near future were identified, thereby raising the profile of these recent technologies and providing vital proof of concept work. Molecular taxonomy, bacterial source tracking and pre-screening of chemicals for potential toxicities were all viewed as areas in which omics and molecular techniques could have immediate value, with the aim of reducing cost, increasing efficiency and providing more comprehensive data of improved quality.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

Sorption and predicted mobility of herbicides in Baltic soils

This study was undertaken to determine sorption coefficients of eight herbicides (alachlor, amitrole, atrazine, simazine, dicamba, imazamox, imazethapyr, and pendimethalin) to seven agricultural soils from sites throughout Lithuania. The measured sorption coefficients were used to predict the susceptibility of these herbicides to leach to groundwater. Soil-water partitioning coefficients were measured in batch equilibrium studies using radiolabeled herbicides. In most soils, sorption followed the general trend pendimethalin > alachlor > atrazine～ amitrole～ simazine > imazethapyr > imazamox > dicamba, consistent with the trends in hydrophobicity (log K_ow) except in the case of amitrole. For several herbicides, sorption coefficients and calculated retardation factors were lowest (predicted to be most susceptible to leaching) in a soil of intermediate organic carbon content and sand content. Calculated herbicide retardation factors were high for soils with high organic carbon contents. Estimated leaching times under saturated conditions, assuming no herbicide degradation and no preferential water flow, were more strongly affected by soil textural effects on predicted water flow than by herbicide sorption effects. All herbicides were predicted to be slowest to leach in soils with high clay and low sand contents, and fastest to leach in soils with high sand content and low organic matter content. Herbicide management is important to the continued increase in agricultural production and profitability in the Baltic region, and these results will be useful in identifying critical areas requiring improved management practices to reduce water contamination by pesticides.     

Radionuclides and trace elements in fish collected upstream and downstream of Los Alamos national laboratory and the doses to humans from the consumption of muscle and bone

Abstract

The purpose of this study was to determine radionuclide and trace element concentrations in bottom‐feeding fish (catfish, carp, and suckers) collected from the confluences of some of the major canyons that cross Los Alamos National Laboratory (LANL) lands with the Rio Grande (RG) and the potential radiological doses from the ingestion of these fish. Samples of muscle and bone (and viscera in some cases) were analyzed for ³H, ⁹⁰Sr, ¹³⁷Cs, ^totU, ²³⁸Pu, ^239,240Pu, and ²⁴¹Am and Ag, As, Ba, Be, Cr, Cd, Cu, Hg, Ni, Pb, Sb, Se, and Tl. Most radionuclides, with the exception of ⁹⁰Sr, in the muscle plus bone portions of fish collected from LANL canyons/RG were not significantly (p<0.05) higher from fish collected upstream (San Ildefonso/background) of LANL. Strontium‐90 in fish muscle plus bone tissue significantly (p<0.05) increases in concentration starting from Los Alamos Canyon, the most upstream confluence (fish contained 3.4E‐02 pCi g^‐1 [126E‐02 Bq kg^‐1]), to Frijoles Canyon, the most downstream confluence (fish contained 14E‐02 pCi g^‐1 [518E‐02 Bq kg^‐1]). The differences in ⁹⁰Sr concentrations in fish collected downstream and upstream (background) of LANL, however, were very small. Based on the average concentrations (±2SD) of radionuclides in fish tissue from the four LANL confluences, the committed effective dose equivalent from the ingestion of 46 lb (21 kg) (maximum ingestion rate per person per year) of fish muscle plus bone, after the subtraction of background, was 0.1 ± 0.1 mrem y^‐1 (1.0 ± 1.0 μSv y^‐1), and was far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem y^‐1 (1000 μSv y^‐1). Of the trace elements that were found above the limits of detection (Ba, Cu, and Hg) in fish muscle collected from the confluences of canyons that cross LANL and the RG, none were in significantly higher (p<0.05) concentrations than in muscle of fish collected from background locations.     

Source identification of copper, lead, nickel, and zinc loading in wastewater reclamation plant influents from corrosion of brass in plumbing fixtures

A natural experiment indicated that a link between the presence and concentration of four elements, copper, lead, nickel, and zinc in the influent to two wastewater reclamation plants to the presence and concentrations of the same four elements in the tap water of residential properties. There were 36 populations of results that were assessed for the normality of their distribution, the difference in their median concentrations, the similarity in the ratios of their median concentrations, and the correlations of the concentrations. The results of this study suggest that brass corrosion is the major source of these four elements in the water reclamation plants influent and that there are two distinct populations of brass sources, those in the early stages of dezincification where the release of the non-copper elements is dominant and those in the later stages where the release of copper dominates and the type of brass that is corroding.     

Effects of Heavy metals on plants and resistance mechanisms

GOAL, SCOPE AND BACKGROUND: As one of the consequences of heavy metal pollution in soil, water and air, plants are contaminated by heavy metals in some parts of China. To understand the effects of heavy metals upon plants and the resistance mechanisms, would make it possible to use plants for cleaning and remediating heavy metal-polluted sites. METHODS: The research results on the effects of heavy metals on plants and resistant mechanisms are compiled from Chinese publications from scientific journals and university journals, mostly published during the last decade. RESULTS AND DISCUSSION: Effects of heavy metals on plants result in growth inhibition, structure damage, a decline of physiological and biochemical activities as well as of the function of plants. The effects and bioavailability of heavy metals depend on many factors, such as environmental conditions, pH, species of element, organic substances of the media and fertilization, plant species. But, there are also studies on plant resistance mechanisms to protect plants against the toxic effects of heavy metals such as combining heavy metals by proteins and expressing of detoxifying enzyme and nucleic acid, these mechanisms are integrated to protect the plants against injury by heavy metals. CONCLUSIONS: There are two aspects on the interaction of plants and heavy metals. On one hand, heavy metals show negative effects on plants. On the other hand, plants have their own resistance mechanisms against toxic effects and for detoxifying heavy metal pollution. RECOMMENDATIONS AND OUTLOOK: To study the effects of heavy metals on plants and mechanisms of resistance, one must select crop cultivars and/or plants for removing heavy metals from soil and water. More highly resistant plants can be selected especially for a remediation of the pollution site. The molecular mechanisms of resistance of plants to heavy metals should be studied further to develop the actual resistance of these plants to heavy metals. Understanding the bioavailability of heavy metals is advantageous for plant cultivation and phytoremediation. Decrease in the bioavailability to farmlands would reduce the accumulation of heavy metals in food. Alternatively, one could increase the bioavailability of plants to extract more heavy metals.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

The natural production of organobromine compounds

Organobromine chemicals are produced naturally by an array of biological and other chemical processes in our environment. Some of these compounds are identical to man-made organobromine compounds, such as methyl bromide, bromoform, and bromophenols, but many others are entirely new moleclar entities, often possessing extraordinary and important biological properties. Although only a few natural organobromine compounds had been discovered up to 1968, this number as of early 1999 is more than 1,600, and new examples are being discovered continually. Organobromine compounds are produced naturally by marine creatures (sponges, corals, sea slugs, tunicates, sea fans) and seaweed, plants, fungi, lichen, algae, bacteria, microbes, and some mammals. Many of these organobromine compounds are used in chemical defense, to facilitate food gathering, or as hormones.     

A History of Dry Cleaners and Sources of Solvent Releases from Dry Cleaning Equipment

Approximately 25, 000-35, 000 dry cleaning facilities currently operate in the U.S. The release of perchloroethylene and other solvents from these establishments represents a major source of soil and groundwater contamination. The manner in which dry cleaning solvents escape from dry cleaning plants is, for all practical purposes, identical for chlorinated and petroleum hydrocarbon solvents and is related to one of the following events: the catastrophic failure of a component of the dry cleaning system, the improper installation, operation or maintenance of the dry cleaning equipment or a combination of all of these causes. Acceptable customs, codes and regulations can also dictate what is authorized for operation of a dry cleaning facility in a particular community, geographic area during a particular time frame. Environmental litigation dealing with the origin of a solvent release from dry cleaners tends to focus on the design and manufacture of dry cleaning industry machines such as washers, washer extractors, tumblers, solvent filters, water separators, stills and spotting boards. A thorough analysis of the daily operations of dry cleaners often reveals that poor maintenance, failure to follow the manufacturer's instructions and the actions of the operator are the most likely causes of soil and groundwater pollution. In order to forensically evaluate the most probable origins of a solvent release and to examine issues regarding liability, a thorough understanding of the history of dry cleaning and a detailed analysis of the operation and maintenance of the dry cleaning equipment are necessary. The discovery of solvent plumes in the vicinity of dry cleaning plants may suggest that the solvent source is the dry cleaning plant; however, the presence of these plumes does not necessarily indicate that the dry cleaning equipment was defectively designed or manufactured. A thorough review of the type of equipment used over the life of the dry cleaning plant and verifiable solvent mileage records frequently indicates that operators of the plant have disposed of solvent and contaminated solids into the municipal sewer or on ground surfaces.     

Radionuclides in deer and elk from Los Alamos national laboratory and the doses to humans from the ingestion of muscle and bone

Abstract

This paper summarizes radionuclide concentrations (³H, ⁹⁰Sr, ¹³⁷Cs, ²³⁸Pu, ^239,240Pu, ²⁴¹Am, and ^totU) in muscle and bone tissue of mule deer (Odocoileus hemionus) and Rocky Mountain elk (Cervus elaphus) collected from Los Alamos National Laboratory (LANL), Los Alamos, New Mexico, lands from 1991 through 1998. Also, the committed effective dose equivalent (CEDE) and the risk of excess cancer fatalities (RECF) to people who ingest muscle and bone from deer and elk collected from LANL lands were estimated. Most radionuclide concentrations in muscle and bone from individual deer (n = 11) and elk (n = 22) collected from LANL lands were either at less than detectable quantities (where the analytical result was smaller than two counting uncertainties) and/or within upper (95%) level background (BG) concentrations. As a group, most radionuclides in muscle and bone of deer and elk from LANL lands were not significantly higher (p<0.10) than in similar tissues from deer (n = 3) and elk (n = 7) collected from BG locations. Also, elk that had been radio collared and tracked for two years and spent an average time of 50% on LANL lands were not significantly different in most radionuclides from road kill elk that have been collected as part of the environmental surveillance program. Overall, the upper (95%) level net CEDEs (the CEDE plus two sigma for each radioisotope minus background) at the most conservative ingestion rate (50 lbs of muscle and 13 lbs of bone) were as follows: deer muscle = 0.22 mrem y^‐1 (2.2 μSv y^‐1), deer bone = 3.8 mrem y^‐1 (38 μSv y^‐1), elk muscle = 0.12 mrem y^‐1 (1.2 μSv y^‐1), and elk bone = 1.7 mrem y^‐1 (17 μSv y^‐1). All CEDEs were far below the International Commission on Radiological Protection guideline of 100 mrem y^‐1 (1000 μSv y^‐1), and the highest muscle plus bone net CEDE corresponded to a RECF of 2E‐06, which is far below the Environmental Protection Agency upper level guideline of 1E‐04.