The fate and transport of arsenic species in the aquatic ecosystem: a case study on Bestari Jaya,Peninsular Malaysia

The field of arsenic pollution research has grown rapidly in recent years. Arsenic constitutes a broad range of elements from the Earth’s crust and is released into the environment from both anthropogenic and natural sources due to its relative mobility under different redox conditions. The toxicity of arsenic is described in its inorganic form, as inorganic arsenic compounds can leach into different environments. Sampling was carried out in the Bestari Jaya catchment while using a land use map to locate the site, and experiments were conducted via sequential extraction and inductively coupled plasma optical emission spectroscopy to quantify proportions of arsenic in the sediment samples. The results show that metals in sediments of nonresidual fractions, which are more likely to be likely released into aquatic environments, are more plentiful than the residual sediment fractions. These findings support the mobility of heavy metals and especially arsenic through sediment layers, which can facilitate remediation in environments heavily polluted with heavy metals.     

Invertebrates control metal/metalloid sequestration and the quality of DOC/DON released during litter decay in slightly acidic environments

Plant litter and organic sediments are a main sink for metals and metalloids in aquatic ecosystems. The effect of invertebrate shredder (a key species in litter decay) on metal/metalloid fixation by organic matter is described only under alkaline water conditions whereas for slightly acidic waters nothing can be found. Furthermore, less is known about the effect of invertebrate shredders on the quality of dissolved organic carbon (DOC) and nitrogen (DON) released during litter decay. We conducted an experiment to investigate the impact of invertebrate shredder (Gammarus pulex) on metal/metalloid fixation/remobilization and on the quality of DOC/DON released under slightly acidic water conditions. During decomposition of leaf litter, invertebrate shredder facilitated significantly the emergence of smaller particle sizes of organic matter. The capacity of metal fixation was significantly higher in smaller particles (POM 2,000?C63???m) compared to original leaf litter and litter residues. Thus, G. pulex enhanced metal fixation by organic partition of sediments by increasing the amount of smaller particle of organic matter in aquatic ecosystems. In contrast, the capacity of metal/metalloid fixation in the smallest fraction of POM (<63???m) was lower compared with leaf residues in treatment without invertebrates. Remobilization of metals and metalloids was very low for all measured elements. A significant effect of invertebrates on quantitative formation of DOC/DON was confirmed. The quality of released DOC/DON, which may affect metal/metalloid remobilization, was also significantly affected by invertebrate shredders (e.g., more carboxylates). Hence, invertebrate shredder enhanced significantly the fixation of metals/metalloids into POM in slightly acidic environments.     

Remediation of an old landsfill site

The Baltic Sea Region has a large number of landfills that need remediation after care routines and control, in order to avoid future emissions to the environment and to fulfil the demands in the EU Waste Council Directive on the landfill of waste. Based on the Måsalycke test screening, an excavation of whole or of parts of the landfill can be seen as a potential measure for some of the old landfills. The material excavated in the test was screened into the fractions: < 18 mm, 182-50 mm and > 50 mm. The coarsest fraction (> 50 mm) contained 50% wood and paper. The medium-sized fraction (18–50 mm) contained stones and indefinable soil-like material, while the fine fraction contained peat-like material with some other small waste components. The spectral analysis of heavy metals indicated only high concentrations of zinc and there was no significant difference between the fine and the medium-sized fractions. The medium sized and the unsorted fraction was moisturized and refilled into the pit. The methane content in the landfill gas from the pit was 50–57% in the sorted material with a flow of 8–17 l/min and 38–57% in the unsorted fraction with a flow of 2–13 l/min during the first 1.5 year. The Måsalycke landfill is in the methanogenic phase and leachate concentrations are normal. Landfill mining can be used to prolong the landfill lifetime and/or used as a tool for remedial actions in contaminated sites.     

Effect of biosolid incorporation on arsenic distribution in Mollisol soils in central Chile

The effect of biosolid incorporation on arsenic distribution in Mollisol soils in central Chile was studied. Two soils were sequentially extracted for arsenic with a five-step method that accounts for the following arsenic forms: non-specifically adsorbed (F1), specifically adsorbed (F2), amorphous and poorly crystallized Fe and Al oxides (F3), well-crystallized Fe and Al oxides (F4) and residual (F5). The arsenic residual fraction was predominant in Pintué soil, whereas in Graneros soil, arsenic was mostly associated to amorphous Fe and Al oxides. Graneros soil exhibited a higher As(V) adsorbing capacity than Pintué soil, which relates to the higher clay and iron and aluminum oxides contents, confirming that these components participation is essential for the adsorption of this metalloid. Biosolid application at a rate of 100Mg ha(-1) caused an increase in arsenic bound to amorphous Fe and Al oxides and in the residual fraction, in Pintué soil. When Pintué soil was spiked with arsenic, aged for two months, and treated with biosolid (100Mg ha(-1)), the content of arsenic in the most labile fractions decreased, thus showing a favorable effect in its application to soils with few specific sites for arsenic adsorption. Arsenic speciation was carried out in the first two fractions of the sequential extraction procedure. As(V) was the main form in both fractions. Biosolid incorporation at a rate of 100Mg ha(-1) caused a significant increase in organic arsenic forms.     

Distribution and partitioning of depleted uranium (DU) in soils at weapons test ranges - investigations combining the BCR extraction scheme and isotopic analysis

Depleted uranium (DU) has become a soil contaminant of considerable concern in many combat zones and weapons-testing sites around the world, including locations in Europe, the Middle East and the USA, arising from its dispersion via the application of DU-bearing munitions. Once DU is released into the environment its mobility and bioavailability will, like that of other contaminants, largely depend on the type of associations it forms in soil and on the nature of the soil components to which it binds. In this study we used the BCR sequential extraction scheme to determine the partitioning of DU amongst soil fractions of texturally varying soils from locations affected by weapons-testing activities. Isotopic analyses (MC-ICP-MS and alpha-spectrometry) were performed to verify the presence of DU in whole soils and soil fractions and to determine any preferential partitioning of the contaminant. Results identified soil organic matter as being consistently the most important component in terms of DU retention, accounting for 30-100% of DU observed in the soils examined. However, at greater distances from known contamination points, DU was also found to be largely associated with the exchangeable fraction, suggesting that DU can be mobilised and transported by surface and near-surface water and does remain in an exchangeable (and thus potentially bioavailable) form in soils.     

Characterization of atmospheric dry deposition particulates in Kobe, Japan

The sources and character of individual metal and metalloid particles from atmospheric dry depositions in Kobe, Japan were investigated. Japan faces long-range pollutant transportation from northeastern Asia during winter and spring. Information regarding their properties and sources is useful for evaluating their affects on the environment and human health. Individual metal and metalloid particles that were collected for every 24 h on the plate, which was designed to reduce a local turbulence, were characterized for their composition, diameter, and deposition fluxes using a field emission scanning electron microscope with an energy dispersive X-ray spectrometer. Approximately 3,000 metal and metalloid particles were classified into 14 types based on their composition and further classified into four groups based on their distribution patterns. They are (A) Fe-O, Fe-Ba-Sb-Cu-S-Ti-O, Fe-Zn-O, Zn-O, Ni-O, and Mn-Fe-O; (B) Cu-Zn-O and Cu-Sn-O; (C) Pb-O, Sn-Sb-O, and Ag-O; (D) Pb-Zn-Cl-Si-S-O and Bi-Cl-O. From these data, this study suggests their sources as the Asian continent (Group A), local source (Group B), multiple sources (Group C), and incineration process (Group D). This study shows (1) the sources and character of individual metal and metalloid particles from short-term atmospheric depositions in Kobe, Japan and (2) application of individual particle analysis for atmospheric depositions.     

Fate and effects of metal-based nanoparticles in two marine invertebrates,the bivalve mollusc Scrobicularia plana and the annelid polychaete Hediste diversicolor

The objective of this paper is to synthesize results from seven published research papers employing different experimental approaches to evaluate the fate of metal-based nanoparticles (Ag NPs, Au NPs, CuO NPs, CdS NPs, ZnO NPs) in the marine environment and their effects on two marine endobenthic species, the bivalve Scrobicularia plana and the ragworm Hediste diversicolor. The experiments were carried out under laboratory (microcosms) conditions or under environmentally realistic conditions in outdoor mesocosms. Based on results from these seven papers, we addressed the following research questions: (1) How did the environment into which nanoparticles were released affect their physicochemical properties?, (2) How did the route of exposure (seawater, food, sediment) influence bioaccumulation and effects?, (3) Which biomarkers were the most responsive? and (4) Which tools were the most efficient to evaluate the fate and effects of NPs in the marine environment? The obtained results showed that metal‐based NPs in general were highly agglomerated/aggregated in seawater. DGT tools could be used to estimate the bioavailability of metals released from NPs under soluble form in the aquatic environment. Both metal forms (nanoparticulate, soluble) were generally bioaccumulated in both species. Among biochemical tools, GST and CAT were the most sensitive revealing the enhancement of anti-oxidant defenses in both species exposed to sub-lethal concentrations of metal-based NPs. Apoptosis and genotoxicity were frequently observed.     

The content of butyl- and phenyltin derivatives in the sediment from the Port of Gdansk

Harbor sediments containing large deposits of organotin compounds constitute a potential threat to the marine environment. Samples of harbor sediments were collected twice in the years 2003 and 2005 from the following locations: Zió?kowskiego, Siarkowe, Wi?lane, Weglowe, Chemików and Paliw P?ynnych Quays. The cores of 25cm length sliced into 2- and 5-cm segments were analyzed. After drying and homogenization, samples were split into two granulometric fractions, i.e. <2.00 and <0.063mm. The dominant fraction in whole sediment, i.e. fraction grain diameter <2.00mm, was sand (grain diameter 2.00-0.063mm). However, the highest concentrations of butyltin (BT) and phenyltin (PT) compounds were found in the fine sediment fraction. The mean values of tributyltin (TBT), dibutyltin (DBT) and monobutyltin (MBT) in the analyzed samples in the <2.00mm fraction were 2144.9, 434.7 and 148.1ngSng(-1)d.w., respectively, while the corresponding mean values in the <0.063mm fraction were 6556.4, 1593.7 and 450.0ngSng(-1)d.w. The mean concentrations of monophenyltin (MPhT) have been estimated at 29.0 and 49.9ngSng(-1)d.w. for the <2.00 and <0.063mm fraction sizes, respectively. The estimated content levels of diphenyltin (DPhT) and triphenyltin (TPhT) were in most cases below the detection limit of the applied method. The sediment cores collected from the locations characterized by high industrialization and intense exploitation (Wi?lane, Weglowe Quays) contained the highest concentrations of BT and PT.     

A simple and fast screening test to detect soils polluted by lead

Lead pollution is an environmental priority. The evaluation of contaminated soils was often based on the results of the toxicity characteristic leaching procedure (TCLP) or the synthetic precipitation leaching procedure (SPLP). This paper presents a simple and fast screening test to detect soil contaminated by lead. The test is based on the chemistry of the stomach (Cl- concentration, pH 2, T = 37 degrees C) and simulates the incidental oral ingestion of soil by young children. The gastric juice simulation test (GJST) and the TCLP were applied to six size fractions from five soils. The GJST solubilized more Pb (up to 169 mg/l) than the TCLP especially for the smallest size fraction. Particle size had less effect on the TCLP. The percentage of lead released with the GJST, was most significant for the <63 microm size fraction and varied from 18 to 74% of the total lead content. Lead leached during the TCLP as a function of the total lead content showed poor linear regression coefficient (R) values for soils <250 microm. R values were significant for all size fractions with the GJST. The pH of approximately 5 in the TCLP limits the solubilization of lead in the small size fractions. The five soils exceeded the toxicity threshold of 10 microgPb/dl of blood for a significant fraction of children between 0 and 36 months using the EPA's IEUBK model (Integrated Exposure Uptake Biokinetic). But the TCLP did not detect lead contamination in two of these five soils. The GJST proved to be a better estimator of lead bioaccessibility in the gastrointestinal tract.     

Assessment of MSWI bottom ash organic carbon behavior: a biophysicochemical approach

In order to understand the influence of organic components on the behavior of municipal solid waste incinerator bottom ash, samples from five French incinerators have been analyzed and compared. Biological and physico-chemical experiments were coupled with a view to developing a new rapid assessment method of bottom ash quality. Bottom ash had different total organic carbon contents ranging from 8.8 g kg(-1) to 37.4 g kg(-1). A part of this organic carbon can be leached into the environment or provide a substrate for microbial activity. Samples showed really different behaviors regarding these processes. Comparative results of leaching tests and biodegradation experiments showed a positive correlation between dissolved organic carbon and microbial activity. However, quantities of biodegraded or leached carbon are not representative of the samples' total organic carbon content. Thermal analyses in oxidizing conditions have revealed the presence of two fractions of organic components, showing different thermal behaviors. The associated mass losses were measured and compared to dissolved organic carbon. One of the two fractions can be directly linked to the leachable and easily biodegradable organic matter fraction. Calorimetric test is then presented as a novel analysis method that allows to provide rapid and global information concerning the characteristics of organic matter in bottom ash and its possible short and long-term evolution.     

Biological and chemical transformation of atrazine in coastal aquatic sediments

The degradation and distribution potential of atrazine, a persistent triazine herbicide, into three chemical fractions were measured in coastal aquatic sediments in the laboratory over time. Sediments with varying organic carbon contents were extracted with an organic solvent followed by an alkali hydrolysis reaction, and atrazine, deethylatrazine (DEA) and deisopropylatrazine (DIA) were quantified in the aqueous, solvent, and basic fractions using gas chromatography-mass spectrometry. The total amount of atrazine and its metabolites recovered after 95 days varied by site and ranged from 5% to 30% in which 95% was atrazine found primarily in the solvent fraction. Sediment organic carbon was positively correlated with the distribution of atrazine into the basic fraction and the decline in the total amount recovered. No DIA was detected in laboratory spiked sediments and transformation to DEA was limited in all sediments and made up less than 1% of the mass balance. The production and persistence of DEA were inversely correlated to organic carbon; sediments with less carbon and limited binding sites had increased formation and persistence of DEA. A secondary metabolite, methylated atrazine (M-ATR) not previously documented to be derived from atrazine, was chemically produced, detected in all sediments and time points, and concentrations were an order of magnitude higher than DEA. Based on results from spiked estuarine sediments, atrazine and M-ATR may have the potential to persist in the environment while DEA and DIA may not be an ecological threat due to their limited formation.     

Variations of arsenic species content in edible Boletus badius growing at polluted sites over four years

The content of arsenic (As) in mushrooms can vary depending on the concentration level of this metalloid in the soil/substrate. The present study evaluated the content of arsenic in Boletus badius fruiting bodies collected from polluted and non-polluted sites in relation to the content of this element in overgrown substrate. It was found that mushrooms from the arsenic-polluted sites contained mean concentrations from 49 to 450 mg As kg^?1 dry matter (d.m.), with the greatest content found for specimens growing in close proximity of sludge deposits (490±20 mg As kg^?1d.m.). The mean content of total arsenic in mushrooms from clean sites ranged from 0.03 to 0.37 mg kg^?1 It was found that B. badius could tolerate arsenic in soil substrate at concentrations of up to 2500 mg kg^?1, at least. In different years of investigation, shifts in particular arsenic forms, as well as a general increase in the accumulation of organic arsenic content, were observed. The results of this study clearly indicate that B. badius should not be collected for culinary purposes from any sites that may be affected by pollution.     

Changes in soil organic matter chemical properties after organic amendments

Organic inputs are used to improve soil physical and chemical properties, but the corresponding changes in soil organic matter (SOM) chemical properties are not well known. In this study, we compared some characteristics of the SOM of a soil receiving either no organic inputs, or two different amendments during 15 years (straw or conifer compost). Quantities of organic carbon and C/N values were determined on particle size fractions after physical soil fractionation to localize changes due to amendments. Contents in reactive functional groups, acid-base properties and copper binding affinities were determined by titration experiments for the soluble fraction of SOM: the fulvic acid fraction (FA). Data of FA extracted from the bulk soil were compared to data of FA extracted from the <20 microm size fraction with the help of either a discrete or a continuous model (fit of data with FITEQL or NICA, respectively). Copper binding characteristics of FA extracted from the <20 microm size fraction did not change significantly after organic inputs, while those of FA extracted from the bulk organic-amended soils were found different from the ones with no amendment. Minor effects observed in the finer soil fractions were ascribed to their low turn-over of organic carbon and/or to a greater homogeneity in the nature of the organic carbon entering these fractions. Our results show major chemical changes in coarser soil organic fractions after organic amendments.     

Sorption of paraquat on clay components in Taiwan's oxisol

The sorption of herbicides in soils is mainly influenced by clay components. The objectives of this study were to evaluate the contribution of clay components on paraquat sorption. The surface soils (0-20 cm) of a Laopi pedon (Fine, mixed, Hyperthermic Typic Hapludox) were separated clays into whole (< 2.0 microm), coarse (0.2-2.0 microm), and fine (< 0.2 microm) fractions with the treatments of removals of organic matter (OM) and free Fe (Fed) oxides. Results indicated that sorption isotherm of paraquat was fitted by the nonlinear Freundlich equation with R2 values ranged in 0.79-0.96, respectively. The shape of paraquat adsorption isotherm on the fine fraction was H-type, but their shapes on the whole and coarse fractions were L-types. The fine clay fractions gave higher contribution on paraquat sorption than the coarse clay fractions identified by their K(f) values. Organic matter associated with fine clay fraction had high CEC contributing to relatively high affinity for paraquat. The DCB treatment created high-affinity sites for paraquat on the fine clay, but had little effect on paraquat sorption for the coarse clay. Chemisorption is the major mechanism for retention of paraquat on clay components, not ion exchange. However, the silicate clay had the highest affinity for paraquat and free Fe compound had the lowest.     

Plant uptake of pesticides and human health: dynamic modeling of residues in wheat and ingestion intake

Human intake of pesticide residues from consumption of processed food plays an important role for evaluating current agricultural practice. We take advantage of latest developments in crop-specific plant uptake modeling and propose an innovative dynamic model to estimate pesticide residues in the wheat-environment system, dynamiCROP. We used this model to analyze uptake and translocation of pesticides in wheat after foliar spray application and subsequent intake fractions by humans. Based on the evolution of residues in edible parts of harvested wheat we predict that between 22 mg and 2.1 g per kg applied pesticide are taken in by humans via consumption of processed wheat products. Model results were compared with experimentally derived concentrations in wheat ears and with estimated intake via inhalation and ingestion caused by indirect emissions, i.e. the amount lost to the environment during pesticide application. Modeled and measured concentrations in wheat fitted very well and deviate from less than a factor 1.5 for chlorothalonil to a maximum factor 3 for tebuconazole. Main aspects influencing pesticide fate behavior are degradation half-life in plant and time between pesticide application and crop harvest, leading to variations in harvest fraction of at least three orders of magnitude. Food processing may further reduce residues by approximately 63%. Intake fractions from residues in sprayed wheat were up to four orders of magnitude higher than intake fractions estimated from indirect emissions, thereby demonstrating the importance of exposure from consumption of food crops after direct pesticide treatment.     

Trace elements in biodeposits and sediments from mussel culture in the Ria de Arousa (Galicia, NW Spain)

The trace elements present at highest concentrations were Cr and Zn, which probably originated from the dumping of effluent from a tanning factory. High proportions of these two elements were associated with the residual fraction. Biodeposits and sediments showed high concentrations of Cd and Pb in the reactive fraction, with a high proportion of the concentration in the reactive fraction being associated with carbonates. Nickel showed a higher degree of pyritization than the previous elements, although most of the Ni was associated with the residual and reactive fractions. Arsenic, Hg and Cu showed high degrees of pyritization, particularly below a depth of 5 cm. The results demonstrate that those elements with a high degree of pyritization may be released into the water through oxidation of the metal sulphides that they form when in suspension in oxic sea water, with the subsequent risk of increased bioavailability to benthic fauna.     

Hydroxypropyl-β-cyclodextrin extractability and bioavailability of phenanthrene in humin and humic acid fractions from different soils and sediments

Organic matter (OM) plays a vital role in controlling polycyclic aromatic hydrocarbon (PAH) bioavailability in soils and sediments. In this study, both a hydroxypropyl-β-cyclodextrin (HPCD) extraction test and a biodegradation test were performed to evaluate the bioavailability of phenanthrene in seven different bulk soil/sediment samples and two OM components (humin fractions and humic acid (HA) fractions) separated from these soils/sediments. Results showed that both the extent of HPCD-extractable phenanthrene and the extent of biodegradable phenanthrene in humin fraction were lower than those in the respective HA fraction and source soil/sediment, demonstrating the limited bioavailability of phenanthrene in the humin fraction. For the source soils/sediments and the humin fractions, significant inverse relationships were observed between the sorption capacities for phenanthrene and the amounts of HPCD-extractable or biodegradable phenanthrene (p?<?0.05), suggesting the importance of the sorption capacity in affecting desorption and biodegradation of phenanthrene. Strong linear relationships were observed between the amount of HPCD-extractable phenanthrene and the amount degraded in both the bulk soils/sediments and the humin fractions, with both slopes close to 1. On the other hand, in the case of phenanthrene contained in HA, a poor relationship was observed between the amount of phenanthrene extracted by HPCD and the amount degraded, with the former being much less than the latter. The results revealed the importance of humin fraction in affecting the bioavailability of phenanthrene in the bulk soils/sediments, which would deepen our understanding of the organic matter fractions in affecting desorption and biodegradation of organic pollutants and provide theoretical support for remediation and risk assessment of contaminated soils and sediments.     

On airborne nano/micro-sized wear particles released from low-metallic automotive brakes

The paper addresses the wear particles released from commercially available “low-metallic” automotive brake pads subjected to brake dynamometer tests. Particle size distribution was measured in situ and the generated particles were collected. The collected fractions and the original bulk material were analyzed using several chemical and microscopic techniques. The experiments demonstrated that airborne wear particles with sizes between 10 nm and 20 μm were released into the air. The numbers of nanoparticles (<100 nm) were by three orders of magnitude larger when compared to the microparticles. A significant release of nanoparticles was measured when the average temperature of the rotor reached 300 °C, the combustion initiation temperature of organics present in brakes. In contrast to particle size distribution data, the microscopic analysis revealed the presence of nanoparticles, mostly in the form of agglomerates, in all captured fractions. The majority of elements present in the bulk material were also detected in the ultra-fine fraction of the wear particles.     

The study on biomass fraction estimate methodology of municipal solid waste incinerator in Korea

In Korea, the amount of greenhouse gases released due to waste materials was 14,800,000 t CO₂eq in 2012, which increased from 5,000,000 t CO₂eq in 2010. This included the amount released due to incineration, which has gradually increased since 2010. Incineration was found to be the biggest contributor to greenhouse gases, with 7,400,000 t CO₂eq released in 2012. Therefore, with regards to the trading of greenhouse gases emissions initiated in 2015 and the writing of the national inventory report, it is important to increase the reliability of the measurements related to the incineration of waste materials.

This research explored methods for estimating the biomass fraction at Korean MSW incinerator facilities and compared the biomass fractions obtained with the different biomass fraction estimation methods. The biomass fraction was estimated by the method using default values of fossil carbon fraction suggested by IPCC, the method using the solid waste composition, and the method using incinerator flue gas.

The highest biomass fractions in Korean municipal solid waste incinerator facilities were estimated by the IPCC Default method, followed by the MSW analysis method and the Flue gas analysis method. Therefore, the difference in the biomass fraction estimate was the greatest between the IPCC Default and the Flue gas analysis methods. The difference between the MSW analysis and the flue gas analysis methods was smaller than the difference with IPCC Default method. This suggested that the use of the IPCC default method cannot reflect the characteristics of Korean waste incinerator facilities and Korean MSW.

Implications: Incineration is one of most effective methods for disposal of municipal solid waste (MSW). This paper investigates the applicability of using biomass content to estimate the amount of CO₂ released, and compares the biomass contents determined by different methods in order to establish a method for estimating biomass in the MSW incinerator facilities of Korea. After analyzing the biomass contents of the collected solid waste samples and the flue gas samples, the results were compared with the Intergovernmental Panel on Climate Change (IPCC) method, and it seems that to calculate the biomass fraction it is better to use the flue gas analysis method than the IPCC method. It is valuable to design and operate a real new incineration power plant, especially for the estimation of greenhouse gas emissions.     

Trace metals in surface sediments of the Taiwan Strait: geochemical characteristics and environmental indication

The concentration and geochemical fractionation of six trace metals related with environmental quality assessment, namely Cd, Cr, Cu, Ni, Pb, and Zn, in 30 surface sediments from both inshore and offshore areas of the Taiwan Strait were measured to investigate their distribution characteristics, evaluate their potential mobility, and assess their pollution status. The geoaccumulation index results indicated that, on average, the studied metals presented an order of Cd?>?Pb?>?Ni?>?Zn?>?Cu?>?Cr and were practically in uncontaminated status except Cd. The results of the sequential extraction analysis indicated that, on average, the studied metals were mostly accumulated in residual fraction except Cd whose concentration was the highest in the acid soluble fraction presenting a high risk to the environment, and their mobility decreased in the sequence of Cd?>?Pb?>?Ni?>?Cu?>?Zn?>?Cr. Based on the mean probable effect level quotients, the combination of the studied metals had an 8 % probability of being toxic at two sampling sites and had a 21 % probability of being toxic at the rest of sites. The spatial distribution of the studied metals in total concentrations and different geochemical fractions corroborated the previous findings about the possible sediment transportation routes in and around the Taiwan Strait.