污泥生物沥滤工艺优化和重金属分配研究

为了得到嗜酸硫细菌沥滤污泥中重金属的最佳工艺参数,对沥滤过程进行3因素4水平的正交实验研究。3种影响因素的水平设置分别为:污泥浓度35、25、15和5 g/L,单质硫投加量15、10、5和1 g/L,接种量15、10、5和3 g/L。对沥滤过程污泥中7种重金属(As、Cd、Cr、Cu、Ni、Pb和Zn)的去除率进行极差分析,提出了因素影响程度依次为单质硫投加量污泥浓度接种量,且最佳工艺条件为:污泥浓度25 g/L,单质硫投加量10 g/L,接种量为5%。采用超声波-离心方法,分步提取污泥胞外聚合物(EPS)的2种形态:松散结合态(LB)和紧密结合态(TB)。分析其中的重金属浓度,提出沥滤后重金属在污泥EPS的赋存以LB为主。     

生物沥滤去除污泥、土壤和底泥中3种重金属比较研究

以硫酸亚铁为底物,对城市污泥、土壤和河流底泥进行生物沥滤实验,探讨了污泥、底泥和土壤在沥滤过程中重金属的去除效果和化学形态转化规律,了解当地土壤在酸化条件下重金属的释放过程,并对三者的研究结果进行比较分析。结果表明,污泥生物沥滤对重金属(Zn、Cu和Pb)的沥滤的沥滤效果较佳(去除率75.45%、63.12%和40.96%)。沥滤过程中,重金属Cu在生物沥滤中期(3~5 d)沥出效果较好,而Zn和Pb则在沥滤后期(5~9 d)。同一重金属在不同沥滤体系中的形态变化过程差异较大,沥滤后的污泥、土壤和底泥中的重金属大部分呈现稳定状态。     

不同污泥浓度对生物沥滤过程的影响

以硫酸亚铁盐作为底物，氧化亚铁硫杆菌（Thiobacillus ferrooxidans）为主要沥滤微生物，在底物投配比为10 g/L，温度为25℃，曝气量为1 L/min的条件下，对5种不同浓度的桂林城市污泥中重金属进行生物沥滤试验。结果表明，生物沥滤的污泥浓度宜控制在25.6 g/L，沥滤3 d后，污泥中超标元素Cu、Zn和Cd的去除率分别达到58.17%、75.90%和93.64%，沥滤处理后污泥中残余重金属含量符合污泥农用的国家标准。     

曝气强度对城市污泥重金属生物沥滤过程的影响研究

以氧化亚铁作为底物，氧化亚铁硫杆菌（Thiobacillusferrooxidans）为主要沥滤微生物，在底物投配比为10 g/L，温度为25℃，污泥浓度为123g/L的条件下，采用5种不同曝气强度对桂林城市污泥中重金属进行生物沥滤试验。结果表明，生物沥滤的经济曝气强度宜控制在每升污泥0.4L/（min·L），沥滤3 d后，污泥中超标元素Cu、Zn和Cd的去除率分别达到62.53%、67.80%和54.63%，沥滤处理后污泥中残余重金属含量符合污泥农用的国家标准。     

底物对生物沥滤去除污泥中Cu、Zn的影响

分别以FeSO2·7H2O、单质S粉为底物,对污泥中的重金属进行生物沥滤试验.通过分析生物沥滤过程中pH、Fe2+、SO22-的变化及Cu、Zn的滤出率.探讨不同底物对重金属生物沥滤的影响.试验结果表明,以FeSO2·7H2O或单质S粉为底物.利用污泥中固有的硫杆菌可以降低污泥的pH.从而使重金属滤出.以单质S粉为底物的处理中,污泥pH最低下降到2.1;以FeSO2·7H2O为底物的处理中,pH最低下降到2.6.经14 d的生物沥滤,以单质S粉为底物时,底物为6 g/L的污泥样品Cu、Zn滤出率最高,分别为18.8%和34.8%;以FeSO2·7H2O为底物时,底物为25 g/L的污泥样品Cu、Zn滤出率最高,分别为29.1%和36.8%.优于以单质S粉为底物的滤出效果.     

微生物沥浸法去除底泥中的重金属

以硫酸亚铁盐为底物,培养以氧化亚铁硫杆菌为主要菌种的土著沥滤微生物,采用批式方法对湘江长沙段底泥进行微生物沥浸实验。实验结果表明,底物投加量与底泥固体浓度比(Sd/Sc)为1.5时已能满足底泥的微生物沥浸要求,进一步研究发现底泥固体浓度为13%、底物投加量为19.5 g/L、沥浸时间为6 d时,底泥中超标重金属Cd、Zn和Cu的去除率可分别达到83.1%、75.3%和61.2%;沥浸后底泥中大部分重金属以残渣态存在,且含量低于农用污泥中污染物控制标准,其中硫化物有机结合态Cu浸出较Zn、Cd需更低的pH,且Cu以间接机理浸出为主;以Fe2+为底物的沥浸体系中,黄铁矾的重吸附或共沉淀是沥浸实验后期重金属浸出率下降的原因之一。     

污泥与煤、木屑燃烧过程中重金属排放特性研究

为了考察燃料燃烧过程中重金属的迁移转化规律，对污泥、煤与木屑及其混合物在不同温度下氧气中燃烧灰渣中的重金属元素进行分析。结果表明，燃料中重金属在高温燃烧时表现出不同的挥发特性，大部分元素随着温度的升高挥发率增加，其中Cd、Pb和Zn元素挥发性较强，Cr、Cu和Ni挥发性较弱。污泥与木屑混合燃烧灰渣仍以污泥灰为主，重金属含量与污泥灰相近，污泥中混入煤后使灰中大部分重金属含量有所降低。燃烧过程会改变重金属存在形态，污泥与煤原料中以酸溶态和可还原态存在的重金属含量较高，具有较强的生物有效性和迁移性，而燃烧灰渣中酸溶态和可还原态含量显著下降，混合燃烧灰渣中除As外的其他重金属几乎全部以残渣态存在，其含量达到90％以上，焚烧过程有效降低了燃料灰渣中重金属的生物毒性。     

生物沥滤-焚烧法处理制革污泥中铬迁移转化研究

采用生物沥滤-焚烧方法,先将制革污泥中大部分难溶的有毒重金属——铬从固相溶出转移至液相,之后将沥滤后制革污泥进行有效的固液两相分离,并对分离后的固相污泥进行焚烧处理实验,研究生物沥滤-焚烧处理法对制革污泥中的总Cr在不同介质中的浓度影响。结果表明,生物沥滤法处理制革污泥后,以金属离子交换形态存在的总Cr含量增加,其中68.56%的总Cr6+和87.70%的总Cr得以去除,去除效果十分明显;将沥滤脱水后的污泥进行焚烧处理,以残渣态形式存在的总Cr相对含量变大,迁移能力减弱;铬在高温下与其他重金属元素形成复杂的金属化合物及络合物:Cr1.3Fe0.7O0.5、Na4(CrO4)(SO4)、Ca5(CrO4)3O0.5,有助于今后进一步对整个生物沥滤-焚烧处理过程进行反应机理研究。     

调理剂对堆肥产品重金属生物有效性的影响

城市污泥中重金属含量及其生物有效性是限制污泥农用的主要因素,因此,研究污泥堆肥化处理过程中重金属生物有效性,对污泥的农用具有重要意义。实验以城市污泥为原料,以菌菇渣和秸秆为调理剂,设置4个处理:A(污泥∶菌菇渣∶秸秆=1∶0.4∶0.025)、B(污泥∶菌菇渣∶秸秆=1∶0.3∶0.025)、C(污泥∶秸秆=1∶0.12)和D(污泥∶秸秆=1∶0.09),进行好氧堆肥实验,采用BCR顺序提取法测定各种形态的重金属,研究堆肥前后重金属形态的变化规律。结果表明,城市污泥中Cu、Ni、Pb和Cr主要以可氧化态及残渣态存在,生物有效性较低,而Zn和Cd主要以酸溶态和可还原态存在,生物有效性较高;堆肥过程显著降低了Cu、Zn、Ni和Pb的生物有效性,并改变了Cu、Zn、Ni、Pb、Cr和Cd的形态分布,使污泥中的Cu、Zn、Ni、Pb和Cd向着更稳定的可氧化态或残渣态转变;污泥经过堆肥处理后,Cu、Zn和Ni 3种重金属生物有效性关系为:ABCD,与其他处理相比,处理A残渣态的Pb和Cr增加比例较多,综合来看,处理A对重金属生物有效性的降低最为明显,重金属钝化效果最佳。     

基于生物淋滤的城市污泥重金属溶出及形态迁移

利用生物淋滤法处理城市污泥,以生物淋滤过程中pH、ORP(氧化还原电位)变化以及重金属(Zn、Cu、Cd)溶出率为指标,考察淋滤菌接种比例、初始pH、淋滤时间对生物淋滤的影响,并分析了生物淋滤前后,重金属形态变化以及重金属的生物有效性和迁移性。结果表明富集筛选的嗜酸性氧化亚铁硫杆菌(A.f)可有效溶出污泥中的重金属。生物淋滤最佳条件为:初始pH=4.00,淋滤菌接种比例30%,重金属Zn,Cu,Cd在第10天的整体处理效果最优,溶出率分别达到75.30%、50.40%和74.44%。BCR形态分析表明:原污泥中Zn,Cu,Cd主要以弱酸提取态、可还原态和氧化态存在,残渣态较少;生物淋滤之后,3种重金属弱酸提取态、可还原态和氧化态含量有不同程度降低,其中,可还原态含量降低最为显著,残渣态基本无变化,并且淋滤后污泥中重金属氧化态及残渣态所占比例较淋滤前高,污泥稳定性得到提升。生物淋滤可以通过减少污泥中重金属含量和改变重金属形态降低其生物有效性和迁移性。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染