油田油泥与煤在流化床中的混烧

基于小型流化床焚烧实验平台,通过含油污泥与煤混合燃烧,分析气体污染物排放浓度以及灰渣特性。含油污泥与煤混烧后NO_x、SO_2的排放浓度均低于危险废物焚烧排放标准。根据灰渣中组分分析,煤中碱金属化合物能抑制SO_2的排放。渣样的浸出毒性均在标准范围内,灰样的浸出毒性高于渣样,主要因为飞灰中更容易富集挥发和易溶形态的重金属。基于小试实验的结果,油泥在小型流化床上的燃烧不充分导致了CO排放浓度较高,且灰的灼减率较高,因此,在后续中试以及示范工程中,应保证油泥的充分燃烧,为灰渣的综合利用提供理论基础。     

燃烧条件对灰渣中重金属元素形态的影响

根据改进了的BCR连续提取法,重金属元素形态分为酸可提取态、氧化物结合态、有机物结合态和残渣态,实验研究了不同燃烧温度、空气流量和燃烧气氛对燃煤重金属(Cr、Mn、Ni、Cu、Zn、As、Cd和Pb)的形态分布和挥发特性的影响规律。结果表明:在原煤和灰渣中,各重金属元素均主要以稳定的残渣态存在;8种重金属元素的挥发性难易程度顺序为Pb、Cd、ZnAs、Cr、Ni、CuMn;燃烧温度从650℃升至1 050℃过程中,各重金属元素4种存在形态的逸出率逐渐升高,逸出率最低增大幅度为20%,最高达60%;随空气流量的增大,重金属元素的有机物结合态和残渣态加速分解和挥发,各重金属元素的逸出率不断增大;除元素Mn和Ni较易于在贫氧气氛中挥发外,元素Cr、Cu、Zn、As、Cd和Pb均在富氧气氛中比较易于挥发气化。     

基于生物淋滤的城市污泥重金属溶出及形态迁移

利用生物淋滤法处理城市污泥,以生物淋滤过程中pH、ORP(氧化还原电位)变化以及重金属(Zn、Cu、Cd)溶出率为指标,考察淋滤菌接种比例、初始pH、淋滤时间对生物淋滤的影响,并分析了生物淋滤前后,重金属形态变化以及重金属的生物有效性和迁移性。结果表明富集筛选的嗜酸性氧化亚铁硫杆菌(A.f)可有效溶出污泥中的重金属。生物淋滤最佳条件为:初始pH=4.00,淋滤菌接种比例30%,重金属Zn,Cu,Cd在第10天的整体处理效果最优,溶出率分别达到75.30%、50.40%和74.44%。BCR形态分析表明:原污泥中Zn,Cu,Cd主要以弱酸提取态、可还原态和氧化态存在,残渣态较少;生物淋滤之后,3种重金属弱酸提取态、可还原态和氧化态含量有不同程度降低,其中,可还原态含量降低最为显著,残渣态基本无变化,并且淋滤后污泥中重金属氧化态及残渣态所占比例较淋滤前高,污泥稳定性得到提升。生物淋滤可以通过减少污泥中重金属含量和改变重金属形态降低其生物有效性和迁移性。     

广西城镇污泥掺烧利用组分特性的分析

对广西城镇污水处理厂污泥进行元素分析、组分分析、工业分析和热重分析,探讨污泥掺烧应用特性,为广西的污泥资源化利用提供数据。结果表明,污泥的元素组成与煤差别较大,如污泥中的氮元素含量为4.627%,高于煤的1.628%;污泥焚烧灰含有高达15%的Si O2;污泥的挥发分为34.6377%比煤的25.089%略高;污泥的焚烧可分为3个阶段,分别为水分析出阶段(室温~160℃)、挥发分析出燃烧阶段(160~500℃)、固定碳及剩余可燃物燃烧阶段(510~950℃),升温速率升高,挥发分析出阶段提前了约50℃,粒径对析出温度影响不大,但粒径小更利于干污泥燃烧。因此,广西污泥是一种低热值,燃烧剧烈的燃料,可以用于掺烧,焚烧灰分具有较高的建材价值。     

洛阳城市污水处理厂污泥中重金属形态及潜在生态风险评价

分析了洛阳市3个污水处理厂脱水污泥中Cu、Zn、Ni、Cr和Pb的含量,采用BCR法研究了污泥中重金属的形态分布特征,并利用地累积指数法(Igeo)和潜在生态危害指数法(RI)评价污泥在农用过程中重金属的潜在生态风险。结果表明,涧西污泥中Cu、Zn和Ni含量超过了农用泥质A级标准的限值(CJ/T309-2009),而新区污泥和瀍东污泥显示出良好的农用性质。污泥中Cu和Cr主要以可氧化态存在,Zn主要以酸溶态和可还原态存在,迁移性强,Ni含量分布相对比较均匀,Pb主要以残渣态存在。Igeo表明,污泥中Cu、Zn是潜在的污染元素。RI表明,Cu表现出高潜在生态风险;Zn的总含量虽高,但Zn的生物毒性响应因子低,对污泥的潜在风险贡献较低。     

污泥焚烧底灰中重金属残留特性的实验研究

利用原子吸收分光光度计和程序控制温升炉研究了沈阳市污水处理厂污泥在不同焚烧工况下重金属Cu、Cr、Cd、Zn、Ni和Pb在焚烧底灰中的残留特性。考察了升温速率、焚烧温度、含水率以及停留时间等因素对重金属在污泥底灰中的残留特性的影响。实验表明 ,Pb、Cd和Cu在灰渣中的残留率随着温度和停留时间的增加而降低。大部分的重金属元素Zn、Cu和Cr残留在灰渣中 ,Cd、Pb和Ni部分残留在灰渣中     

超积累植物东南景天热解过程中Cd的迁移转化规律及炭产物安全利用研究

在管式炉对Cd超积累植物东南景天(Sedum alfredii)进行热解,研究热解过程中Cd的迁移和形态转化,并在最佳温度条件下探究制备的东南景天生物炭对Cd的吸附作用。结果表明,随着温度上升,生物炭产率下降,挥发分增加;温度能影响Cd在气、液、固三相中的分布,温度升高能明显促进重金属由固相向气相迁移;生物炭中Cd形态受温度影响,随温度升高,对环境影响较大的水溶态和酸溶态Cd含量呈现出降低趋势,在700℃以上时,大部分Cd是以稳定的可氧化态、可还原态以及残渣态形式存在;800℃热解得到的东南景天生物炭对Cd具有一定的吸附效果,最高吸附量达到28.7mg/g。通过合理控制热解温度能够实现炭产物的稳定化,并可安全利用到重金属污染水体或者农田污染治理中。     

污泥焚烧底灰中重金属残留特性的实验研究

利用原子吸收分光光度计和程序控制温升炉研究了沈阳市污水处理厂污泥在不同焚烧工况下重金属Cu,Cr,Cd,Zn,Ni和Pd在焚烧底灰中的残留特性，考察了升温速率，焚烧温度，含水率以及停留时间等因素对重金属在污泥底灰中的残留特性的影响，实验表明，Pd,Cd和Cu在灰渣中的残留率随着渐度和停留时间的增加而降低，大部分的重金属元素Zn,Cr和Cu残留在灰渣中，Cd,Pb和Ni部分残留在灰渣中。     

煤粉炉掺烧干化污泥的污染物排放研究

结合某电厂420 t/h四角煤粉炉掺烧污泥项目的实验室分析测试,了解煤粉掺烧不同含水率不同比例的干化污泥条件下烟气中污染物和灰渣中重金属的排放特性。结果表明,在实验研究配比和燃烧的条件下,大部分重金属元素Pb、Cu、Cr和Ni残留在灰渣中,Zn、Cd部分残留在灰渣中,As、Hg和Se等易挥发元素释放到烟气中,在灰渣中的含量很小。掺烧污泥后,灰渣中的重金属含量较单烧单煤都有了一定幅度的升高,Zn的含量是单煤的2倍,其余重金属是单煤的1.1~1.2倍。3种不同的掺混比例之间的污染气体排放浓度基本相似。烟气中主要污染物及重金属浓度可以满足现行国家标准。与单烧单煤相比,CO、HCl以及其他有机气体排放浓度基本相同;NH3的排放浓度较单煤有所升高;SO2、NOx和CO2排放浓度略有降低;飞灰浓度有所升高。烟气中的重金属,Hg含量升高了30%,Pb含量约为单煤的4.3~4.8倍。以上研究结果可为环保达标和飞灰利用提供基础数据。     

调理剂对堆肥产品重金属生物有效性的影响

城市污泥中重金属含量及其生物有效性是限制污泥农用的主要因素,因此,研究污泥堆肥化处理过程中重金属生物有效性,对污泥的农用具有重要意义。实验以城市污泥为原料,以菌菇渣和秸秆为调理剂,设置4个处理:A(污泥∶菌菇渣∶秸秆=1∶0.4∶0.025)、B(污泥∶菌菇渣∶秸秆=1∶0.3∶0.025)、C(污泥∶秸秆=1∶0.12)和D(污泥∶秸秆=1∶0.09),进行好氧堆肥实验,采用BCR顺序提取法测定各种形态的重金属,研究堆肥前后重金属形态的变化规律。结果表明,城市污泥中Cu、Ni、Pb和Cr主要以可氧化态及残渣态存在,生物有效性较低,而Zn和Cd主要以酸溶态和可还原态存在,生物有效性较高;堆肥过程显著降低了Cu、Zn、Ni和Pb的生物有效性,并改变了Cu、Zn、Ni、Pb、Cr和Cd的形态分布,使污泥中的Cu、Zn、Ni、Pb和Cd向着更稳定的可氧化态或残渣态转变;污泥经过堆肥处理后,Cu、Zn和Ni 3种重金属生物有效性关系为:ABCD,与其他处理相比,处理A残渣态的Pb和Cr增加比例较多,综合来看,处理A对重金属生物有效性的降低最为明显,重金属钝化效果最佳。     

The behaviour of phosphorus and heavy metals in sewage sludge ashes

The effect of the combustion atmosphere and the additives (CaO and HCl) on the behaviour of phosphorus and heavy metals during sewage sludge combustion was investigated. The results demonstrated that the reduction combustion promoted the vapourisation of phosphorus and heavy metals during sewage sludge combustion. Moreover, the concentrations of phosphorus and heavy metals in the bottom ash decreased with increasing HCl ratio, and the addition of CaO can stabilise heavy metals and phosphorus. It was also observed that phosphorus and heavy metals increased with increasing CaO ratio. Lastly, the difference of the TG-DTA curves with and without additives is discussed.     

垃圾焚烧过程中影响重金属分布因素的研究

在转式垃圾焚烧炉和固定床加热炉中,研究了有机垃圾焚烧过程中温度、水分、无机氯及有机氯对几种重金属分布的影响。研究结果表明,焚烧垃圾过程中焚烧温度对重金属分布特性的影响特性不一,重金属锌和铅容易转移到气相中去,而重金属镍和铬大部分是以固态形式残留在底渣中;水能与重金属及其化合物发生反应,引起物质转变,影响重金属的分布;氯的存在也影响重金属的分布特性,氯的参与使重金属更易向飞灰或烟气中迁移。     

Characteristics of fundamental combustion and NOx emission using various rank coals

Eight types of coals of different rank were selected and their fundamental combustion characteristics were examined along with the conversion of volatile nitrogen (N) to nitrogen oxides (NOx)/fuel N to NOx. The activation energy, onset temperature, and burnout temperature were obtained from the differential thermogravimetry curve and Arrhenius plot, which were derived through thermo-gravimetric analysis. In addition, to derive the combustion of volatile N to NOx/fuel N to NOx, the coal sample, which was pretreated at various temperatures, was burned, and the results were compared with previously derived fundamental combustion characteristics. The authors' experimental results confirmed that coal rank was highly correlated with the combustion of volatile N to NOx/fuel N to NOx.     

Emission characteristics for co-combustion of leather wastes,sewage sludge,and coal in a laboratory-scale entrained flow tube furnace

Four different mixed fuels consisted of leather waste, coal, and sewage sludge were combusted in a lab-scale entrained flow fluidized bed furnace. The influence of blending ratio on emission characteristics of SO₂, NO_x, HCl, particulate matter (PM), heavy metals, and polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) was studied. Results showed that the mixing of coal with sewage sludge had a complex effect on the emission characteristics. On the one hand, with more sewage sludge blending in the mixed fuel, the acid gas pollutant (SO₂, NO_x) decreased a lot, and the recovery of volatile heavy metals (Cd, Pb) increased at the same time. Furthermore, the leaching toxicity of Cr in the fly ash and bottom ash went down below the national standard with the adding of sewage sludge. On the other hand, the mixing of sewage sludge which consisted of more ash content resulted in the increase of the PM emission. Moreover, the high content of Cu and chlorine in the sewage sludge can promote the formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) when the fuel 3 and 4 were combusted. Most importantly, the concentration of toxic PCDD/Fs in the flue gas produced from fuel 3 and fuel 4 was successfully controlled down below 0.20 ng I-TEQ/Nm³ by the active carbon.

     

污水污泥中重金属污染物的溶出过程研究

污水污泥中污染物尤其是重金属的水体浸出作为重要的二次污染途径备受关注。为了探讨污水污泥中重金属的溶出规律,对上海7个污水处理厂的污水污泥进行了重金属总量分析,并采用水平振荡法对上述污水污泥中重金属进行了溶出动力学研究。结果表明,污水污泥中Cu、Cr和Zn的含量均较高,之后依次是Pb、As、Cd和Hg;污水污泥中重金属溶出动力学过程分为快速反应和慢速反应两个过程,可以用Elovich方程进行模拟;污水污泥中各重金属的溶出负荷差异较大,Cu、Cr和Zn的溶出负荷较大,其他较小,但各重金属相对于污水污泥中重金属总量的溶出百分比差异不大,基本处于10%以下。     

以城市污泥为掺料制备烧结砖

以城市污泥为部分原料制备烧结砖,对不同烧成温度下不同污泥掺量的烧结砖的物理、力学性能进行了详细分析。结果表明,污泥可用于制备烧结砖,当污泥掺量≤12%,烧成温度为1 100℃时,烧结砖物理力学性能均符合烧结砖标准要求。此外,实验以污泥掺量为12%的烧结砖,烧成温度为1 100℃为例,进行了重金属毒性浸出实验,以考察烧制污泥砖对重金属的固化作用,进而评定污泥制砖的安全性。结果表明,经过高温焙烧,大多数重金属浸出毒性都显著降低,且符合规范要求,不会对环境造成危害。其中,重金属固化效果最好的为Zn,最差的为Cr。     

还原焙烧电镀污泥中的金属形态和浸出性

分别以煤粉和稻杆为还原剂对电镀污泥进行还原焙烧，并通过酸浸回收焙烧渣中的金属。研究了焙烧温度、焙烧时间和还原剂投加量对目标金属Cu浸出率的影响以及主要杂质金属的浸出性，并采用BCR逐级提取法分析了焙烧前后污泥中的金属形态分布。结果表明，当在电镀污泥中投加30％的煤粉在600℃下焙烧1h后Cu的浸出率达到97．78％，当投加50％的稻杆时浸出率为89．47％，而氧化焙烧后浸出率仅为37．71％；并且还原焙烧渣中多数杂质金属的浸出率较低，从而可以实现Cu与杂质金属的初步分离。氧化焙烧容易导致金属从易浸出的非残渣态向难浸出的残渣态转化，而还原焙烧则能抑制这种转化过程，金属形态是决定其浸出性的重要因素。     

Influence of ozone pre-treatment on sludge anaerobic digestion: removal of pharmaceutical and personal care products

The effect of an oxidative pre-treatment with ozone on the removal of Pharmaceutical and Personal Care Products (PPCPs) during the anaerobic digestion of sewage sludge has been investigated. Besides, the digested sludge characteristics in terms of pathogens content, dewatering properties, heavy metals content and linear alkylbenzene sulfonates (LAS) were determined. During ozonation (20mg O(3)/g TSS), about 8% of volatile solids (VS) and 60% of the chemical oxygen demand (COD) were solubilized. However, no mineralization was observed. The elimination of VS and total COD during anaerobic digestion were not affected by ozone treatment with efficiencies ranging from 60% to 65%. All PPCPs considered were removed during anaerobic treatment of sludge, with efficiencies ranging from 20% to 99%. No significant influence of ozone pre-treatment was observed on PPCPs elimination except for carbamazepine. Pathogens, heavy metals and LAS contents after conventional and pre-ozonation treatment of sewage sludge were below the legal requirements. However, the dewatering properties of sludge were deteriorated when the ozone pre-treatment was applied.     

PCDD/F, PAH and heavy metals in the sewage sludge from six wastewater treatment plants in Beijing, China

In order to better understand land application of sewage sludge, the characterization of heavy metals, PCDD/F and PAHs in sewage sludge was investigated from six different wastewater treatment plants (WWTP) in Beijing City, China. It was found that the total concentrations of Zn in Wujiacun (WJC) sewage sludge, and Cd and Hg in sewage sludge generated from all of the six different places are higher than Chinese regulation limit of pollutants for sludge to be used for agriculture (GB18918-2002). The levels of 16 PAHs that have been categorized as priority pollutants by US EPA in the sewage sludge samples varied from 2467 to 25923 microg/kg (dry weight), the highest values of 25923 microg/kg being found in WJC WWTP. The concentrations of Benzo[a]pyrene were as high as 6.1mg/kg dry weight in WJC sewage sludge, exceeding the maximum permitted content by GB18918-2002. Individual PAH content varies considerably with sewage samples. The ratios of anthracene to anthracene plus phenanthrene (An/178), benz[a]anthracene to benz[a]anthracene plus chrysene (BaA/228), indene[1,2,3-cd]pyrene to indene[1,2,3-cd]pyrene plus benzo[g,h,i]perylene (In/In+BP), and fluoranthene to fluoranthene plus pyrene (Fl/Fl+Py) suggest that petroleum and combustion of fossil fuel were the dominant contributions for the PAHs in sewage sludge. The concentrations of total PCDD/F in the sewage sludge ranged from 330 to 4245 pg/g d.w. The toxicity equivalent concentrations is between 3.47-88.24 pg I-TEQ according to NATO/CCMS, which is below Chinese legislation limit value proposed for land application. The PCDD/F congener/homologue profiles found in the Beijing samples indicated that the high chlorinated PCDD/F contamination might originate mainly from PCP-related source and depositional sources while the low chlorinated PCDD/F homologues could be originating from incineration or coal combustion. The major source of PCDD/Fs in Beijing sludge is still unclear.