污泥热干化和燃烧特性试验研究

分别在桨叶式干化机和热重仪上进行污泥干化和燃烧试验,研究了污泥干化特性和污染物排放特性,并对污泥的燃烧特性进行分析。结果表明,污泥干化过程分为黏稠区、粘滞区和颗粒区3个阶段。干化过程排放的污染气体有氨气、氯化氢、氟化氢、氰化氢、甲烷和挥发性有机酸等,其中氨气为主要污染气体。经冷凝吸收和活性炭吸附处理后,各种污染气体浓度均显著降低,其中氨气去除率最高,达97.04%。污泥干化冷凝液的BOD5和COD质量浓度分别为4 040、8 510mg/L,氨氮的质量浓度为1 025mg/L,pH为9.84,属于高浓度有机废水。污泥的燃烧过程可以分为3个失重阶段:水分析出阶段(50～150℃),挥发分燃烧阶段(150～450℃),固定碳燃烧阶段(450～650℃)。分别用Kissinger法和Ozawa法计算挥发分燃烧阶段和固定碳燃烧阶段的活化能和动力学方程,挥发分燃烧阶段的活化能低于固定碳燃烧阶段,表明挥发分燃烧阶段污泥更易燃烧。污泥的燃烧过程在650℃时基本完成,因此实际工程应用中,设计干化污泥的焚烧温度在750℃比较合理。     

生活污泥与煤混烧及热解特性

采用热重分析法,对生活污泥与煤以1∶1质量比混合的试样进行燃烧及热解实验研究,重点分析了升温速率对其热解及燃烧特性的影响,为煤泥混烧及热解技术的工业化应用提供理论支持。结果表明:煤泥混合样燃烧失重分为4个阶段,混燃过程中污泥与煤共同影响着混合试样的燃烧特性,随着升温速率从15℃·min~(-1)增加到50℃·min~(-1),其可燃性指数C增幅达60%和综合燃烧特性指数S提高了4倍多,燃烧性能得到明显提高;煤泥混合样的热解失重分为2个阶段,各阶段热解的挥发份最大析出速率(dw/dt)_(max)及挥发分析出特性指数D均随升温速率的升高而大幅增大,且试样总的挥发综合释放指数D从0.081 7×10~(-8)K~(-3)·min~(-2)增大到5.868×10~(-8)K~(-3)·min~(-2),可见升温速率越高,煤泥混合物的热解性能越好。     

石灰调质污泥的燃烧特性及动力学分析

采用热重-差示扫描量热同步分析仪,在空气气氛下对石灰调制污泥进行燃烧失重实验.通过分析获得的曲线,可以将调质污泥的热反应过程分为4个阶段:自由水和化学结合水析出阶段;易挥发有机质析出和燃烧阶段;难挥发有机质析出分解和燃烧阶段;无机质的分解阶段.添加石灰后,污泥的着火温度小幅上升,综合燃烧特性指数随添加量增加而减小.采用Coats-Redfern积分法对挥发分析出和燃烧阶段进行了热反应动力学求解,发现添加量小于30％时,石灰可以减少污泥燃烧的活化能,促进污泥挥发分的析出和燃烧.     

污泥与煤、木屑燃烧过程中重金属排放特性研究

为了考察燃料燃烧过程中重金属的迁移转化规律，对污泥、煤与木屑及其混合物在不同温度下氧气中燃烧灰渣中的重金属元素进行分析。结果表明，燃料中重金属在高温燃烧时表现出不同的挥发特性，大部分元素随着温度的升高挥发率增加，其中Cd、Pb和Zn元素挥发性较强，Cr、Cu和Ni挥发性较弱。污泥与木屑混合燃烧灰渣仍以污泥灰为主，重金属含量与污泥灰相近，污泥中混入煤后使灰中大部分重金属含量有所降低。燃烧过程会改变重金属存在形态，污泥与煤原料中以酸溶态和可还原态存在的重金属含量较高，具有较强的生物有效性和迁移性，而燃烧灰渣中酸溶态和可还原态含量显著下降，混合燃烧灰渣中除As外的其他重金属几乎全部以残渣态存在，其含量达到90％以上，焚烧过程有效降低了燃料灰渣中重金属的生物毒性。     

TG-FTIR研究生物质成型燃料热解与燃烧特性

利用热重-红外联用分析仪(TG-FTIR)研究了生物质成型燃料(玉米秸杆)的热解和燃烧特性。结果表明,热解和燃烧反应过程均可分为3个阶段:干燥脱气(100~200℃)、挥发分反应(200~400℃)与碳化反应(400~1 000℃)。热解和燃烧主要失重阶段(200~400℃),燃烧反应速率总体上大于热解反应速率。利用Coats-Redfern方法对玉米秸杆的主要失重阶段进行动力学分析发现,热解和燃烧的反应过程符合一级反应模型;在主要失重阶段(200~400℃),热解和燃烧所需的活化能相差不大。FTIR分析表明,热解的气相产物主要分为轻质类气体(H2O、CO2、CO、CH4、HCl、NH3和HCN)和焦油类(酸类和酚类)物质,而燃烧的气相产物主要以CO2和H2O析出为主。     

市政污泥与不同烟煤混合燃烧特性

使用非等温热重法,研究了淮北烟煤和神华烟煤在6种不同市政污泥掺混比条件下对混合燃烧特性的影响,并对混合燃烧过程的动力学特性进行了分析。实验结果表明:污泥与煤的混合燃烧特性从总体上表现为污泥与煤共同作用的结果,最优的污泥掺混比受到煤种的影响。在不同煤中污泥掺烧比少于20%对煤的活性影响较小。活化性能较差的淮北烟煤在污泥掺混比为30%时,在不同的温度区间分别表现出污泥与煤的反应特征。活化性能较好的神华烟煤在污泥掺混比为40%时表现这一趋势。     

城市下水污泥焚烧过程中二次污染物排放特性的试验研究

在0.15 MWt循环流化床燃烧试验台上进行了城市下水污泥与煤的混烧试验,分析了烟气中的二次污染物排放特性.分析结果表明,利用循环流化床焚烧城市下水污泥时,添加辅助燃料(如煤)及改变焚烧条件,不仅可以达到稳定燃烧的目的,而且有利于抑制焚烧中二次污染物(如CO及二恶英等有机污染物)的生成.分析了焚烧污泥污染物的排放特性,为采用焚烧方式处理城市下水污泥提供了基础性试验数据.     

模拟陈腐垃圾掺烧过程中P/Cl/S对6种重金属迁移特性的影响

通过管式炉焚烧实验,探究了在陈腐垃圾与城市生活垃圾(MSW)掺烧过程中,P/Cl/S对6种重金属(Cd、Zn、Ni、Cu、Cr、Pb)迁移规律的影响,并考察了陈腐垃圾掺混比例、含特征元素的添加剂种类及焚烧温度对6种重金属挥发率的影响.结果 表明,当陈腐垃圾掺烧比例与温度相同时,NaH2PO4和Na2SO4的协同作用对Cd挥发有显著的抑制作用,但对Ni、Cu的挥发起促进作用;NaCl对Zn的挥发有明显的抑制作用,但对Cr的挥发起促进作用;而NaCl和Na2SO4的协同作用促进了Pb的挥发.随着焚烧温度在设定范围(600～800℃)内的增加,Cd、Ni、Cr和Pb的挥发率整体呈增加的趋势.相比添加剂种类,陈腐垃圾掺混比例对Cd、Cr、Cu挥发率的影响更显著.本研究结果可为制定有效的重金属控制策略提供参考.     

煤粉炉掺烧干化污泥的污染物排放研究

结合某电厂420 t/h四角煤粉炉掺烧污泥项目的实验室分析测试,了解煤粉掺烧不同含水率不同比例的干化污泥条件下烟气中污染物和灰渣中重金属的排放特性。结果表明,在实验研究配比和燃烧的条件下,大部分重金属元素Pb、Cu、Cr和Ni残留在灰渣中,Zn、Cd部分残留在灰渣中,As、Hg和Se等易挥发元素释放到烟气中,在灰渣中的含量很小。掺烧污泥后,灰渣中的重金属含量较单烧单煤都有了一定幅度的升高,Zn的含量是单煤的2倍,其余重金属是单煤的1.1~1.2倍。3种不同的掺混比例之间的污染气体排放浓度基本相似。烟气中主要污染物及重金属浓度可以满足现行国家标准。与单烧单煤相比,CO、HCl以及其他有机气体排放浓度基本相同;NH3的排放浓度较单煤有所升高;SO2、NOx和CO2排放浓度略有降低;飞灰浓度有所升高。烟气中的重金属,Hg含量升高了30%,Pb含量约为单煤的4.3~4.8倍。以上研究结果可为环保达标和飞灰利用提供基础数据。     

不同氧浓度下脱脂餐厨垃圾燃烧特性及动力学研究

利用热重分析法和Coats-Redfern积分法,对不同氧浓度下脱脂餐厨垃圾的燃烧特性进行研究,得到了各试样的着火温度、燃烬温度及综合燃烧特性指数,并通过燃烧动力学分析得到各试样的活化能。实验结果表明,燃烧温度从室温升至1 000℃时,脱脂餐厨垃圾燃烧过程可分为3个失重阶段:水分析出阶段、挥发分析出及燃烧阶段和固定碳燃烧阶段;随着氧浓度的升高,脱脂餐厨垃圾最大失重率以及燃烧特性指数等燃烧特性参数都有显著变化。根据Coats-Redfern积分法计算得低温和高温阶段的活化能分别为83.76~91.2 k J/mol和95.25~141.7 k J/mol。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.