吸附增效低温等离子体法去除甲苯废气的研究

采用150Hz中频高压交流电源作为低温等离子体发生源,选用典型的微孔γ-Al2O3球形颗粒吸附剂(以下简称γ-Al2O3)作为等离子体反应器填充材料,协同低温等离子体法催化降解甲苯废气。考察了在不同条件下,γ-Al2O3的甲苯吸脱附效果和吸附增效低温等离子体法的甲苯去除效果。结果表明,甲苯降解反应主要发生在γ-Al2O3的表面,甲苯的去除率在一定的浓度范围内与γ-Al2O3表面吸附的甲苯量成正比关系;填充γ-Al2O3有利于提高甲苯去除率及等离子体反应器能量利用率;γ-Al2O3对臭氧的降解表现出一定的促进作用。     

活性炭处理甲苯气体吸附再生实验研究

研究了活性炭对甲苯废气的吸附穿透过程及热空气解吸过程.穿透曲线实验结果表明,在常规空塔气速范围内,传质区高度基本在5.06～9.75 cm,传质区不饱和度在0.4～0.7.在动态运行情况下,活性炭对甲苯的饱和吸附容量在0.16～0.24 g/g.热空气吹脱实验表明,适宜的脱附工况条件为脱附温度180 ℃、脱附空气流速0.106 m/s、脱附时间40 min.     

甲苯气体的动态吸附净化及吸附剂再生实验研究

研究了活性炭纤维(ACF)对甲苯气体的动态吸附净化过程及热空气解吸脱附再生过程.采用3种经验方程对ACF的吸附等温线进行拟合,其中Langmuir方程拟合效果最好,拟合相关系数R2 =0.9960,说明在给定的浓度范围内,ACF对甲苯的吸附是以单分子层吸附为主.穿透曲线实验表明,ACF对甲苯吸附效果较好,Yoon-Ne...     

低温等离子体催化降解甲苯的影响因素分析

采用吸附存储/低温等离子体催化技术降解甲苯,分析了催化剂M/13X-Al(M为Ag、Fe、Cu)、放电电压、甲苯吸附量对低温等离子体氧化效果的影响。结果表明:Ag/13X-Al具有较大的穿透吸附量与较高的CO_x(CO_2、CO)产率。当放电电压由12kV升高至22kV,活性粒子大量增加,CO_x产率从32%提高至71%;而当甲苯吸附量增加,单个甲苯分子与活性粒子的碰撞几率降低,CO_x产率急剧下降。     

介质阻挡放电等离子体降解高浓度甲苯

为解决喷漆和涂装废气中VOCs的污染,采用同轴圆管式介质阻挡反应器进行低温等离子体降解高浓度甲苯探索,研究了反应器参数(放电间距、放电长度)、操作参数(初始甲苯浓度、气体流量、输入功率)等关键参数对甲苯转化率和产物CO2选择性的影响。结果表明:放电间距过大或者过小都不利于甲苯的降解,放电长度的增加对其影响相对较小;输入功率越大,甲苯的降解效果越好,并且反应产物中臭氧的浓度越低,但气体流量及初始甲苯浓度的增加不利于甲苯的降解。最后对产物进行GC-MS检测,分析了甲苯降解机理。     

活性炭纤维(ACF)应用于有机废气回收和净化的进展

活性炭纤维(ACF)有比普通活性炭吸附量大、吸附和脱附速度快等优点,因此应用于有机废气的回收和净化,具有良好的经济、环境和社会效益。文中介绍了ACF的微观结构、表面化学以及吸附性能,并综述了近年来ACF在有机废气回收和治理方面的国内概况。     

介质阻挡放电和水吸收联合降解挥发性有机化合物

依据介质阻挡放电(DBD)和溶液吸收处理气态污染物的原理,设计出一种DBD和水吸收联合降解挥发性有机化合物(VOCs)的实验装置.研究其对甲苯的降解效果.考察了放电电压、甲苯初始浓度、模拟废气流量对甲苯降解效果的影响.分析了DBD和水吸收的相互作用.结果表明.DBD和水吸收联合可以提高甲苯的降解率.在放电电压为15.9 kV时甲苯的降解率为81.5%.比单独放电时提高了13.3百分点;甲苯的降解率随着放电电压增大而升高,随着气体流量和甲苯初始浓度增大而降低.该技术可以作为放电等离子体前处理工艺,为高效处理上业废气提供参考.     

电晕-介质阻挡协同放电低温等离子体降解大流量甲苯废气的研究

利用自制电晕-介质阻挡协同放电低温等离子体降解大流量甲苯废气,运用均匀设计法优化获得甲苯降解的适宜条件,探究了各因素及因素间交互作用对甲苯降解的影响,并开展甲苯降解动力学分析。结果表明:降解甲苯的最佳条件为工作电压13kV、放电频率6.5kHz、废气流量为1.0L/min,甲苯初始质量浓度924mg/m~3,在此条件下甲苯气体降解率为94.93%,能量效率为0.63g/(kW·h);甲苯降解符合一级反应动力学,甲苯降解反应速率常数与输入功率具有良好线性关系。     

沸石分子筛和活性炭吸附/脱附甲苯性能对比

考察了甲苯在NaY型沸石分子筛(简写为NaY)、13X型沸石分子筛(简写为13X)、Hβ型沸石分子筛(简写为Hβ)、MCM-22型沸石分子筛(简写为MCM-22)和ZSM-5型沸石分子筛(简写为ZSM-5)上的吸附/脱附性能,同时与椰壳活性炭(AC)的吸附/脱附性能进行对比.结果表明,各吸附剂对甲苯的平衡吸附量大小依次为:AC>NaY>Hβ>13X>MCM-22>ZSM-5,甲苯从吸附剂表面脱附难易程度依次为:AC>NaY、13X>Hβ>MCM-22>ZSM-5>ZSM-5对甲苯的平衡吸附量和吸附强度都最小,这是由于甲苯无法进入ZSM-5的内部孔道造成的;在低甲苯质量浓度(<1 000 mg/m3)时.NaY平衡吸附量超过AC,因此NaY更适合应用在低浓度有机废气吸附治理中,Langmuir吸附方程比Freundlich吸附方程更符合沸石分子筛吸附甲苯的行为.     

反应条件对等离子体脱除吸附于Cu-Ce/AC表面NO_x的影响

以放电等离子体协同催化法对吸附在Cu-Ce/AC上的NO_x进行脱除,研究了不同的放电条件和添加水蒸气对脱除NO_x的影响。结果表明,对于同轴圆筒形反应器,催化剂量一定时,放电长度增加,吸附态NO_x去除率先升高后下降;放电电压增大,吸附态NO_x去除率升高,原因在于放电反应区内能量密度和活性粒子分布状态改变。根据NO_x程序升温脱附(TPD),TPD低温位(200℃)的吸附态NO_x更容易被放电等离子体脱除,放电长度和放电电压能够影响不同吸附位上NO_x的去除效率。适宜条件下,吸附态NO_x去除率最高达到93.3%。循环吸附-等离子体脱除NO_x进行10次后,NO_x脱除率在92%以上。在混合气中添加5%水蒸气提高了等离子体对吸附态NO_x的去除率,但导致循环吸附-等离子体脱除NO_x效率下降。原因是H2O与NO_x竞争吸附带来的负面效应大于等离子体中H2O提供自由基与吸附态NO_x反应所带来的正面效应。     

Selection and Substantiation of an Organic Solvent Removal Apparatus at a Print Shop by Comparative Experiments Using the Activated Carbon Adsorption and Catalytic Oxidation Methods

ABSTRACT

The investigation of an appropriate organic solvent removal apparatus for installation in a newly reconstructed print shop as a countermeasure for preventing the exhaust of organic solvents was conducted.

The selection of an organic solvent removal apparatus was made after bench-scale tests of the activated carbon adsorption method and the catalytic oxidation method, both of which are effective for the removal of organic solvents, were performed on the actual exhaust gas at the print shop. The results showed that both methods were efficient enough to be applied to the removal of organic solvents, but the activated carbon adsorption method had many drawbacks, such as the need for frequent replacement of activated carbon and complex maintenance. For the catalytic oxidation method, running costs are high, but there are many merits, such as that the catalysts do not have to be replaced as often and maintenance is simple. After considering these factors, a catalytic oxidation removal apparatus was installed at the new print shop. In the results of the substantiation test on the actual apparatus using mixed catalysts of platinum and manganese plus copper, the removal efficiency was 97.998.7% and the concentration of the outlet exhaust gas was about 10 ppm (the average concentration of the inlet exhaust gas was 528 ppm) at a space velocity of 30,000 hr^-1 and a reaction temperature of 200 °C. The results of this study were substantiated.     

Decomposition of low-concentration gas-phase toluene using plasma-driven photocatalyst reactor

Plasma-driven photocatalysis system was prepared and performed. To overcome the treatment difficulty of volatile organic compounds, non-thermal plasma was used as a light source of photocatalysis. The removal of low-concentration toluene was investigated and secondary products were analyzed by gas chromatograph–mass spectroscopy. The plasma-driven photocatalyst reactor using direct current as a light source and titanium dioxide catalyst loaded on activated carbon fiber (TiO₂/ACF) as photocatalyst was studied. It was found that plasma-driven photocatalysis system could significantly increase the removal effect of toluene. The number of secondary products was largely decreased. It means that plasma-driven photocatalysis hybrid system was an effective method for the removal of volatile organic compounds.     

Ozone Injection into an Activated Carbon Bed to Remove Hydrogen Sulfide in the Presence of Concurrent Substances

ABSTRACT

Adsorption using activated carbon is one of the most reliable techniques for preventing odor by substances such as H₂S. Concurrent substances in effluent gas often reduce the removal capacity of activated carbon for H₂S. As a means of restoring capacity under such conditions, ozone injection into an activated carbon column was examined. When activated carbon was saturated with substances such as toluene, ethanol, n-butanol, or iso-butanol, its capacity to remove H₂S decreased in proportion to the amount of the saturating substance. Under such conditions, ozone injection greatly increased capacity. Toluene, which is not easily decomposed by ozone, was displaced by ozone and by oxidized products of H₂S. Ethanol, which is adsorbed in small amounts by activated carbon and easily decomposed by ozone, was removed by ozone injection. Butanols, which are also decomposed by ozone and adsorbed in large quantities by activated carbon, showed intermediate behavior between that of toluene and ethanol.     

活性碳纤维吸附甲苯废气吸附等温方程的研究

研究了固定床吸附器中粘胶基活性碳纤维(viscose rayon-based ACFs)吸附甲苯废气的特性,通过实验测定活性碳纤维吸附不同浓度甲苯废气的穿透曲线,作出等温吸附曲线,根据实验数据拟合出几个吸附平衡方程,并与实验结果进行比较.实验结果可为工业设备设计提供参考.     

活性碳纤维吸附甲苯废气吸附等温方程的研究

研究了固定床吸附器中粘胶基活性碳纤维（viscose rayon-based ACFs）吸附甲苯废气的特性，通过实验测定活性碳纤维吸附不同浓度甲苯废气的穿透曲线，作出等温吸附曲线。根据实验数据拟合出几个吸附平衡方程，并与实验结果进行比较。实验结果可为工业设备设计提供参考。     

Adsorption properties of regenerative materials for removal of low concentration of toluene

A specific type of material, activated carbon fiber (ACF), was modified by SiO₂, and the final products ACF-x were obtained as ACF-12.5, ACF-20, ACF-40, and ACF-80 according to different dosages of tetraethoxysilane (TEOS). The modified material on the ACF surface had a significant and smooth cover layer with low content of silica from scanning electron microscope (SEM) image. The modified ACF-x showed the stronger hydrophobicity, thermal stability, and adsorption capacity, which had almost no effect in the presence of water vapor and no destruction in multiple cycles. ACF-20 was proven as the most efficient adsorbent in humid conditions. The dual-function system composed of the regenerative adsorbents and the combustion catalyst would be efficient in consecutive toluene adsorption/oxidation cycles, in which the combustion catalyst was prepared by the displacement reaction of H₂PtCl₆ with foam Ni. Therefore, the adsorption/catalytic oxidation could be a promising technique in the indoor air purification, especially in the case of very low volatile organic compound (VOC; toluene) concentration levels.

Implications: Exploring highly effective adsorptive materials with less expensive costs becomes an urgent issue in the indoor air protection. ACF-20 modified by SiO₂ with Pt/Ni catalysts shows stronger hydrophobicity, thermal stability, and adsorption capacity. This dual-function system composed of the regenerative materials and the combustion catalyst would be a promising technique in the indoor air purification, especially in the case of removal of very low concentration of toluene.     

微波再生载苯酚活性炭过程中再生产物分析

研究了载氮气和无载气2种条件下,微波再生载苯酚活性炭过程中再生产物的成分和苯酚随再生过程的去向分布。结果表明,无载气时,微波功率越高,再生反应器内温度越高,吸附质的高温裂解反应越彻底,再生产物以挥发性气体为主,有机质种类很少;而当微波功率较低或载氮气再生时,反应器内温度相对较低,苯酚难以被彻底分解,再生产物中含多种复杂的链状或环状有机物。此外,载氮气时,经气提、挥发而去除的苯酚量约占总吸附量的一半,再生炭上无苯酚残留,活性炭吸附性能可完全恢复乃至优化;无载气时,经挥发而去除的苯酚量只有19.9%,其余大量苯酚则在微波作用下裂解或缩合为其他物质随尾气而去除,且再生炭上仍有少量苯酚未被解吸出来。因此,前者活性炭再生的效果优于后者。     

脉冲电晕低温等离子体提高一氧化氮氧化效率的实验研究

提高一氧化氮（NO）的氧化效率对于提高生物法处理该类废气的净化效率具有重要意义。实验研究了低温等离子体在脉冲电晕条件下氧化废气中NO的过程，考察了不同峰值电压、氧气含量、气体停留时间和添加有机物等因素对提高NO氧化效率的影响。结果表明：低温等离子法可有效地提高NO的氧化效率，主要产物为NO₂；室温条件下，当进气NO浓度590 mg/m³、脉冲频率50 Hz时，增大峰值电压、气体停留时间和进气中的氧气含量可提高NO的氧化效率；在最适峰值电压15 kV，气体停留时间5 s时，NO氧化效率为20%；在进气NO中添加甲苯、乙醇后，NO氧化效率可增加至30%以上，甲苯的效果要好于乙醇。     

Adsorption Characteristics of Activated Carbon and XAD4 Resin for the Removal of Hazardous Organic Solvents

A comparative study has been conducted on adsorption/desorption of six hazardous organic vapors on synthetic resin (XAD4) and activated carbon, using a differential reactor involving the expansion of a quartz spring. While both sorbents can effectively remove the organic vapors, it was observed that at low concentrations activated carbon adsorbed more organic vapor than synthetic resin. At higher, industrial concentrations, the resins adsorbed more vapor as demonstrated by the slopes of the equilibrium isotherms. The resin also showed much higher desorptlon.

The effective Intraparticle diffusion coefficients (D_e) were observed to be strongly dependent on solute concentration. Pore diffusion dominated the adsorption/desorption of the six organic vapors on XAD4 resin. For the carbon system, pore diffusion dominated the adsorption but surface diffusion contributed to the desorptlon process. This is believed to be due to higher Interaction of the adsorbates with activated carbon.