The separation of catalyst after photocatalytic reactions conducted in the presence of TiO2/FeCl3/UV

One of the problems connected with wastewater treatment by the photocatalytic method in the presence of TiO2 suspension is necessity of the later catalyst separation. The method proposed by us for this purpose, consists in the usage of coagulation of TiO2 suspension with the aid of FeCl3, particularly in the cases when addition of the salt is used in order to intensification of the photocatalytic process. The effects of the TiO2 separation were studied from the mixtures, after photocatalytic Acid Orange 7 degradation, with dosage of FeCl3 at different stages of the process. The coagulation was carried out at different pH values as well as different FeCl3 concentrations. It was stated that nearly 100% of separation and simultaneously, nearly 100% of decolouration of the examined Acid Orange 7 solutions after their illumination in the presence of TiO2/FeCl3 and coagulation which was produced only by increasing of pH of the obtained mixtures, were nearly possible.     

Kinetic and adsorption study of acid dye removal using activated carbon

The adsorption of three acid dyes, Acid Red 97, Acid Orange 61 and Acid Brown 425 onto activated carbon was studied for the removal of acid dyes from aqueous solutions at room temperature (25 degrees C). The adsorption of each dye with respect to contact time was then measured to provide information about the adsorption characteristics of activated carbon. The rates of adsorption were found to conform to the pseudo-second-order kinetics with a good correlation. The experimental isotherms obtained, except for Acid Orange 61 studied in mixture, were of the S-type in terms of the classification of Giles and co-workers. The best fit of the adsorption isotherm data was obtained using the Freundlich model. When a comparative study was made of the results obtained with single and mixed dyes, it can be seen that some of them affect others and modify their behavior in the adsorption process. The results indicate that activated carbon could be employed for the removal of dyes from wastewater.     

流动注射分光光度法研究离子强度对活性炭吸附阴、阳离子染料的影响

运用流动注射分光光度法,考察了不同离子强度(NaCl)下,在水溶液中表面带负电的活性炭分别吸附阴、阳离子染料的动力学行为。实验结果表明,对于所考察的2种阳离子染料和3种阴离子染料,活性炭的表观吸附速率常数均随着离子强度的增大而增大。这种加速吸附效应的出现,主要是因为离子强度的增大促进了活性炭表面与染料之间的非静电力作用。     

Comparative performance evaluation of Aspergillus lentulus for dye removal through bioaccumulation and biosorption

Dyes used in various industries are discharged into the environment and pose major environmental concern. In the present study, fungal isolate Aspergillus lentulus was utilized for the treatment of various dyes, dye mixtures and dye containing effluent in dual modes, bioaccumulation (employing growing biomass) and biosorption (employing pre-cultivated biomass). The effect of dye toxicity on the growth of the fungal isolate was studied through phase contrast and scanning electron microscopy. Dye biosorption was studied using first and second-order kinetic models. Effects of factors influencing adsorption and isotherm studies were also conducted. During bioaccumulation, good removal was obtained for anionic dyes (100 mg/l), viz. Acid Navy Blue, Fast Red A and Orange-HF dye (99.4 %, 98.8 % and 98.7 %, respectively) in 48 h. Cationic dyes (10 mg/l), viz. Rhodamine B and Methylene Blue, had low removal efficiency (80.3 % [48 h] and 92.7 % [144 h], respectively) as compared to anionic dyes. In addition to this, fungal isolate showed toxicity response towards Methylene Blue by producing larger aggregates of fungal pellets. To overcome the limitations of bioaccumulation, dye removal in biosorption mode was studied. In this mode, significant removal was observed for anionic (96.7–94.3 %) and cationic (35.4–90.9 %) dyes in 24 h. The removal of three anionic dyes and Rhodamine B followed first-order kinetic model whereas removal of Methylene Blue followed second-order kinetic model. Overall, fungal isolate could remove more than 90 % dye from different dye mixtures in bioaccumulation mode and more than 70 % dye in biosorption mode. Moreover, significant color removal from handmade paper unit effluent in bioaccumulation mode (86.4 %) as well as in biosorption mode (77.1 %) was obtained within 24 h. This study validates the potential of fungal isolate, A. lentulus, to be used as the primary organism for treating dye containing wastewater.     

The evaluation of electrical energy per order (E(Eo)) for photooxidative decolorization of four textile dye solutions by the kinetic model

Photooxidative decolorization of four textile dyestuffs, C.I. Acid Orange 7 (AO7), C.I. Acid Orange 8 (AO8), C.I. Acid Orange 52 (AO52) and C.I. Acid Blue 74 (AB74), by UV/H2O2 was investigated in a laboratory scale photoreactor equipped with a 15 W low pressure mercury vapour lamp. The decolorization of the dyes was found to follow pseudo-first-order kinetics, and hence the figure-of-merit electrical energy per order (E(Eo)) is appropriate for estimating the electrical energy efficiency. The E(Eo) values were found to depend on the concentration of H2O2, concentration and basic structure of the dye. This study shows that these textile dyes can be treated easily and effectively with the UV/H2O2 process with E(Eo) values between 0.4 and 5 kW h m-3 order-1, depending on the initial concentrations of dyes and H2O2. The kinetic model, based on the initial rates of degradation, provided good prediction of the E(Eo) values for a variety of conditions.     

Photocatalytic degradation of azo dyes by nitrogen-doped TiO2 nanocatalysts

This study examined the photocatalytic degradation of three azo dyes, acid orange 7 (AO7), procion red MX-5B (MX-5B) and reactive black 5 (RB5) using a new type of nitrogen-doped TiO2 nanocrystals. These newly developed doped titania nanocatalysts demonstrated high reactivity under visible light (lambda>390 nm), allowing more efficient usage of solar light. The doped titania were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Experiments were conducted to compare the photocatalytic activities of nitrogen-doped TiO2 nanocatalysts and commercially available Degussa P25 powder using both UV illumination and solar light. It is shown that nitrogen-doped TiO2 after calcination had the highest photocatalytic activity among all three catalysts tested, with 95% of AO7 decolorized in 1 h under UV illumination. The doped TiO2 also exhibited substantial photocatalytic activity under direct sunlight irradiation, with 70% of the dye color removed in 1h and complete decolorization within 3 h. Degussa P25 did not cause detectable dye decolorization under identical experimental conditions using solar light. The decrease of total organic carbon (TOC) and evolution of inorganic sulfate (SO4(2-)) ions in dye solutions were measured to monitor the dye mineralization process.     

Biological treatment of dye wastewaters using an anaerobic-oxic system

Three dye solutions, namely, C.I. Acid Yellow 17, C.I. Basic Blue 3, and C.I. Basic Red 2, were treated in an upflow anaerobic sludge blanket (UASB) reactor followed by a semi-continuous aerobic activated sludge tank. When hydraulic retention time was about 12 hours, no significant color removal was observed in the aerobic stage. In the anaerobic stage, Acid Yellow 17, Basic Blue 3, and Basic Red 2 were removed by 20%, 72%, and 78%, respectively. To treat wastewater from a dye manufacturing factory with COD concentration of 1200 mg/l and Color of 500 degree (dilution factor), an UASB reactor (4.5 liters) and an activated sludge tank (5 liters, adjustable), COD and color were removed by more than 83% and 90% at a COD loading rate of 5.3 kg COD/m³-day in the anaerobic stage, and at the hydraulic retention time of 6-10 hours for the anaerobic stage and 6.5 for the aerobic stage. The anaerobic stage of the A/O system removes both color and COD. In addition, it also improves biodegradability of dyes for further aerobic treatment.     

Removal of Yellow ME 7 GL from industrial effluent using electrochemical and adsorption techniques

Attempts have been made to remove toxic dye Yellow ME7GL using electrochemical and adsorption techniques. Both techniques are capable of reducing toxicity and producing clean water for reuse. The electrochemical removal is carried out at platinum electrode and cyclic voltammograms of the dye solutions have been recorded at different pH, concentrations, scan rates, etc. The adsorption of the dye has been carried out over activated charcoal and wheat husk and verified by Langmuir and Freundlich adsorption isotherms. The decolouration of the dye was also examined by monitoring the Chemical Oxygen Demand (COD) of the untreated and treated dye solutions.     

膨胀珍珠岩负载TiO2光催化脱色性能的研究

以钛酸四丁酯为原料 ,膨胀珍珠岩为载体 ,用溶胶 -凝胶法制备可漂浮于水面的负载型TiO2 。利用该负载型TiO2 对罗丹明B(RB)进行光催化脱色实验 ,结果表明 ,浸渍 3次的负载型TiO2 光催化活性最高 ,催化剂最佳用量为 5 0 0mg/10 0mLRB ,经 5h光照 ,对 10 0mL浓度为 1mg/L和 2 .5mg/LRB脱色率分别为 76 .6 7%和 4 7.2 7% ;该催化剂使用寿命长 ,2 5h后催化剂脱色性能没有减弱 ,可重复使用 ;经 8h光照 ,染料废水脱色效果好。     

Advanced oxidation processes in azo dye wastewater treatment.

The chemical degradation of synthetic azo dyes color index (C.I.) Acid Orange 7, C.I. Direct Orange 39, and C.I. Mordant Yellow 10 has been studied by the following advanced oxidation processes: Fenton, Fenton-like, ozonation, peroxone without or with addition of solid particles, zeolites HY, and NH4ZSM5. Spectrophotometric (UV/visible light spectrum) and total organic carbon measurements were used for determination of process efficiency and reaction kinetics. The degradation rates are evaluated by determining their rate constants. The different hydroxyl radical generation processes were comparatively studied, and the most efficient experimental conditions for the degradation of organic azo dyes solutions were determined.     

Degrading a mixture of three textile dyes using photo-assisted electrochemical process with BDD anode and O2–diffusion cathode

In this paper, degradation of a mixture of three azo dyes was studied by the photo-assisted electrochemical process using an O₂-diffusion cathode containing carbon nanotubes and boron-doped diamond (BDD) anode. The concentration of three textile dyes (C.I. Acid Orange 8 (AO8), C.I. Acid Orange 10 (AO10), and C.I. Acid Orange 12 (AO12)) was determined simultaneously despite the severe overlap of their spectra. For this purpose, partial least square (PLS), as a multivariate calibration method, was utilized based on recording UV–Vis spectra during the decolorization process. Moreover, the central composite design was used for the modeling of photo-assisted electrochemical decolorization of the aqueous solutions containing three dyes. The investigated parameters were the initial concentration of three dyes, applied current and reaction time. Analysis of variance (ANOVA) revealed that the obtained regression models match the experimental results well with R (Khataee et al. 2010, Clean-Soil Air Water 38 (1):96–103, 2010) of 0.972, 0.971, and 0.957 for AO8, AO10, and AO12, respectively. Three-dimensional surface and contour plots were applied to describe the relation between experimental conditions and the observed response. The results of TOC analysis confirmed good ability of proposed photo-assisted electrochemical process for degradation and mineralization of textile industry wastewater.     

Photodestruction of Acid Orange 7 (AO7) in aqueous solutions by UV/H2O2: influence of operational parameters

The photodestruction of Acid Orange 7 (AO7), an anionic acidic dye, was studied in the UV/H2O2 process. H2O2 and UV light have a negligible effect when they were used on their own. Removal efficiency of AO7 was sensitive to the operational parameters such as initial H2O2 concentration, initial AO7 concentration, pH and different light sources. The photodestruction of AO7 was inhibited by addition of EtOH as an electron scavenger. The semi-logarithmic graphs of the concentration of AO7 versus time (t<30 min) were linear, suggesting pseudo-first order reactions (k(optimum)=0.105 min(-1)). A simple kinetic model is proposed which is in agreement with experimental results.     

表面活性剂改性活性炭对阳离子染料的吸附

以阴离子表面活性剂十二烷基硫酸钠(SDS)为改性剂对粉末活性炭(AC)改性,研究了SDS在活性炭表面的吸附稳定性,用比表面积测定仪、Zeta电位测定仪对改性前后活性炭进行表征,并将其用于吸附模拟废水中的阳离子染料。结果表明,改性剂SDS浓度等于临界胶束浓度时,改性后活性炭(SDS-AC)对SDS吸附稳定,SDS在纯水和染料溶液中的解吸率分别为19.4%和1.6%。pH对活性炭吸附阳离子橙染料影响较小,SDS-AC和AC对染料的吸附平衡时间分别为4 h和12 h,SDS-AC和AC对阳离子橙染料的吸附动力学模型符合拟二级反应模型,吸附等温线更符合Langmuir吸附等温方程,SDS-AC对阳离子橙染料的最大吸附量较AC提高47.8%,SDS-AC对阳离子橙染料的吸附机制为物理吸附和化学吸附共同作用下的单分子层吸附,其中化学吸附是主要控速步骤。     

Application of zeolite-activated carbon macrocomposite for the adsorption of Acid Orange 7: isotherm, kinetic and thermodynamic studies

In this study, the adsorption behavior of azo dye Acid Orange 7 (AO7) from aqueous solution onto macrocomposite (MC) was investigated under various experimental conditions. The adsorbent, MC, which consists of a mixture of zeolite and activated carbon, was found to be effective in removing AO7. The MC were characterized by scanning electron microscopy (SEM), energy dispersive X-ray, point of zero charge, and Brunauer–Emmett–Teller surface area analysis. A series of experiments were performed via batch adsorption technique to examine the effect of the process variables, namely, contact time, initial dye concentration, and solution pH. The dye equilibrium adsorption was investigated, and the equilibrium data were fitted to Langmuir, Freundlich, and Tempkin isotherm models. The Langmuir isotherm model fits the equilibrium data better than the Freundlich isotherm model. For the kinetic study, pseudo-first-order, pseudo-second-order, and intraparticle diffusion model were used to fit the experimental data. The adsorption kinetic was found to be well described by the pseudo-second-order model. Thermodynamic analysis indicated that the adsorption process is a spontaneous and endothermic process. The SEM, Fourier transform infrared spectroscopy, ultraviolet–visible spectral and high performance liquid chromatography analysis were carried out before and after the adsorption process. For the phytotoxicity test, treated AO7 was found to be less toxic. Thus, the study indicated that MC has good potential use as an adsorbent for the removal of azo dye from aqueous solution.     

Kinetic modeling on photooxidative degradation of C.I. Acid Orange 7 in a tubular continuous-flow photoreactor

The decolorization of C.I. Acid Orange 7 (AO7), an anionic monoazo dye of acid class, was investigated using UV radiation in the presence of H2O2 in a tubular continuous-flow photoreactor as a function of oxidant and dye concentrations, reactor length and volumetric flow rate. The removal efficiency of AO7 depends on the operational parameters and increases as the initial concentration of H2O2 is increased but it decreases when the flow rate and initial concentration of AO7 are increased. The decolorization rate follows pseudo-first order kinetic with respect to the dye concentration. A rate equation for decolorization of AO7 was achieved by kinetic modeling. This model allows predicting concentration of AO7 in different photoreactor lengths for different volumetric flow rates and initial concentrations of H2O2 and AO7. The calculated results obtained from kinetic model were in good agreement with experimental data.     

Reducing degradation of azo dye by zero-valent iron in aqueous solution

The reducing degradation kinetics of five azo dyes, Acid orange II, Acid orange IV, Acid orange GG, Acid red 3B and Orange I, by zero-valent iron powder in aqueous solution were studied. It showed that the degradation is a two-step reaction, with the first step being reversible. Solution acidity and iron surface area are the factors greatly influencing the degradation rates, and with increasing of acidity and iron surface area, the degradation rates increase.     

Competitive adsorption of dye metanil yellow and RB15 in acid solutions on chemically cross-linked chitosan beads

One kind of adsorbent with a high adsorption capacity for anionic dyes was prepared using ionically and chemically cross-linked chitosan beads. A batch system was applied to study the adsorption behavior of one acid dye (MY, metanil yellow) and one reactive dye (RB15, reactive blue 15) in aqueous solutions by the cross-linked chitosan beads. The adsorption capacities was 3.56 mmol g(-1) (1334 mg g(-1)) for dye MY and 0.56 mmol g(-1) (722 mg g(-1)) for dye RB15 at pH4, 30 degrees C. The Langmuir model agreed very well with the experimental data (R(2)>0.996). The kinetics of adsorption for a single dye and the kinetics of removal of ADMI color value in mixture solutions at different initial dye concentrations were evaluated by the nonlinear first-order and second-order models. The first-order kinetic model fits well with the dynamical adsorption behavior of a single dye for lower initial dye concentrations, while the second-order kinetic model fits well for higher initial dye concentrations. The competitive adsorption favored the dye RB15 in the mixture solution (initial conc. (mM): MY=1.34; RB15=1.36); while it favored the dye MY in the mixture solution (initial conc. (mM): MY=3.00; RB15=1.34) and the adsorption kinetics for dye RB15 has the tendency to shift to a slower first order model.     

零价铁复合有机膨润土处理染料废水的研究

针对目前印染废水处理现状及膨润土在水处理中回收困难等问题，提出将零价铁复合到有机膨润土中制成零价铁复合有机膨润土(ZVI-OB)，以达到高效吸附并降解污染物的目的。以染料废水(Orange II) 作为研究对象，考察了废水中染料的初始浓度、pH以及吸附时间对ZVI-OB去除染料效率的影响，并研究了吸附后降解过程中时间和pH对污染物降解的影响以及降解前后膨润土层结构的变化。研究结果表明，ZVI-OB相对于CTMAB改性的有机膨润土而言，其吸附量有所降低，但ZVI-OB在吸附污染物之后能有效降解有机物。ZVI-OB在饱和吸附Orange II后经催化氧化，总有机碳含量降低为原来的19%，可以重复利用。     

褐煤对废水中酸性红B的吸附去除

选用褐煤作为廉价吸附剂,脱除模拟废水中染料酸性红B。研究了褐煤对废水中酸性红B的吸附动力学、等温吸附模式,考察了pH、褐煤投加量以及离子强度(NaCl)对吸附效果的影响。结果表明,吸附动力学较好地符合准二级速率方程(R2=1.000),并且以化学吸附为主;吸附等温式满足Langmuir方程(R2=0.986),最大单分子层吸附量为42 mg/g;废水中染料的去除率随溶液pH的减小而明显增加,在pH=1时,去除效果最好,证实吸附过程存在静电吸引及化学键合;在一定条件下,溶液中酸性红B的去除率随褐煤投加量增加而增加;吸附效果随溶液中离子强度(NaCl)的增加而增强。说明褐煤可以作为一种廉价吸附材料,用于处理含染料废水。     

污泥吸附剂对3种染料吸附动力学的研究

以污水厂脱水污泥、锯末和焦油的混合物为原料，选择ZnCl₂为活化剂制备出过渡孔发达、强度大的污泥吸附剂（S-AC）。借助BET、FT-IR等现代分析测试方法对污泥吸附剂进行表征，同时，研究了吸附剂对酸性大红、中性红和碱性品红吸附动力学行为。结果表明，制得的污泥吸附剂BET比表面积为358 m²/g，强度大于89%。吸附剂的动力学数据均符合伪二阶动力学方程、液膜扩散方程和颗粒内扩散方程，其中液膜扩散为吸附剂对酸性大红吸附过程的主控步骤，颗粒内扩散为吸附剂对中性红和碱性品红吸附过程的主控步骤。