Effect of start of main injection timing on performance,emission, and combustion characteristics of a VGT CI engine fueled with neem biodiesel

The performance of engine parameters is more influenced with fuel injection strategies namely start of main injection timing (SoMI). An experimental analysis was performed to find the optimum SoMI timing based on performance, emission, and combustion characteristics. Base fuel of diesel and neem biodiesel was used as test fuels. The neem biodiesel was prepared by esterification and transesterification process. It is found from literature that neem biodiesel blend NB20 with diesel gives optimum performance and emission characteristics; therefore, NB20 blend was used for experiments. A variable geometry turbocharger (VGT) compression ignition (CI) engine was used to conduct the experiments. Engine performance parameters were estimated and compared with a base fuel of diesel and with NB20 blends. In this experimentation, fuel injection pressure (FIP) of 800 bar and engine speed of 1700 rpm were considered. SoMI timing was varied from 2° to 10° bTDC with an increment of 2° bTDC timing. Cylinder pressure (CP) and heat release rate (HRR) were estimated and found that are higher for diesel fuel compared to NB20 blend at different SoMI timings. The addition of neem biodiesel NB20 blend to diesel fuel decreases the exhaust emissions except NOx emissions. The BSFC was considerably reduced and BTE was improved almost equivalent to the diesel fuel for NB20. From the results, it is concluded that 10° bTDC SoMI timing provides 13% improvement in BTE, 21% decrement in BSFC, and 7.5% reduction in CO₂ emissions.

     

An experimental investigation on waste fishing net as an alternate fuel source for diesel engine

In this experimental study, the feasibility of using the oil obtained from waste fishing net as a substitute for diesel fuel was investigated. Waste fishing net oil (WFNO) was obtained through pyrolysis process on a laboratory scale setup and used as a fuel in diesel engine. The properties of oil obtained from waste fishing net were examined and compared with conventional diesel fuel. Results indicated that the WFNO possesses excellent fuel properties. The calorific value of WFNO is 44,450 kJ/kg, which is higher than diesel by 1.48%. In order to study the possibility of using WFNO and its blends (WFNO 25%, WFNO 50%, WFNO 75% and WFNO 100%) with diesel as a fuel, an experimental investigation was carried out on a single-cylinder, four-stroke diesel engine. Experimental results proved that WFNO works satisfactorily on a diesel engine without any engine modifications. Brake thermal efficiency was decreased and brake-specific fuel consumption was increased while using WFNO and its blends. Moreover, there was a slight increase in engine emissions like CO, UHC, NO with WFNO and its blends.

     

An experimental study on usage of plastic oil and B20 algae biodiesel blend as substitute fuel to diesel engine

Usage of plastics has been ever increasing and now poses a tremendous threat to the environment. Millions of tons of plastics are produced annually worldwide, and the waste products have become a common feature at overflowing bins and landfills. The process of converting waste plastic into value-added fuels finds a feasible solution for recycling of plastics. Thus, two universal problems such as problems of waste plastic management and problems of fuel shortage are being tackled simultaneously. Converting waste plastics into fuel holds great promise for both the environmental and economic scenarios. In order to carry out the study on plastic wastes, the pyrolysis process was used. Pyrolysis runs without oxygen and in high temperature of about 250–300 °C. The fuel obtained from plastics is blended with B20 algae oil, which is a biodiesel obtained from microalgae. For conducting the various experiments, a 10-HP single-cylinder four-stroke direct-injection water-cooled diesel engine is employed. The engine is made to run at 1500 rpm and the load is varied gradually from 0 to 100 %. The performance, emission and combustion characteristics are observed. The BTE was observed to be higher with respect to diesel for plastic-biodiesel blend and biodiesel blend by 15.7 and 12.9 %, respectively, at full load. For plastic-biodiesel blend, the emission of UBHC and CO decreases with a slight increase in NO _x as compared to diesel. It reveals that fuel properties are comparable with petroleum products. Also, the process of converting plastic waste to fuel has now turned the problems into an opportunity to make wealth from waste.     

The influence of ceramic-coated piston crown,exhaust gas recirculation,compression ratio and engine load on the performance and emission behavior of kapok oil–diesel blend operated diesel engine in comparison with thermal analysis

In this work, the development and usability of kapok oil in diesel engine was intended. With this purpose, the piston crowns are coated with mullite–lanthanum (ML) ceramic composite at varying compositions in order to reduce the heat rejection during combustion process. The kapok oil is blended with diesel fuel consisting of (20% kapok oil–80% diesel) volumetrically named B fuel. The B and diesel (D) fuels are taken for the engine performance test with different coated piston (ML1, ML2, and ML3) and exhaust gas recirculation (EGR—10%, 20%, and 30%), compression ratio (CR—16, 17, and 18) and engine load (50%, 75%, and 100%). Also, the engine performance study on brake thermal efficiency (BTE), brake-specific fuel consumption (BSFC), hydrocarbons (HCs), oxides of nitrogen (NOx), carbon monoxide (CO), smoke opacity, and numerical study using ANSYS software is carried out. When operated with ML2-coated pistons with B fuel, maximum BTE value of 29.2%, minimum BSFC value of 0.224 kg/kW-h, CO emission of 0.2%, and smoke opacity of 39 ppm were observed. The results showed that ML2-coated piston considerably improved the performance of the test engines when compared with ML1 and ML3 coatings. Except for NOx emission, all other pollutant emission values were reduced. The numerical analysis using ANSYS software for ML2-coated pistons showed better retention of in-cylinder chamber temperature.

     

Performance and exhaust emission characteristics investigation of compression ignition engine fuelled with microalgae biodiesel and its diesel blends

Biofuels extracted from plant biomass can be used as fuel in CI engines to lower a hazardous atmospheric pollutant and mitigate climate risks. Furthermore, its implementation is hampered by inevitable obstacles such as feedstocks and the crop area required for their cultivation, leading to a lack of agricultural land for the expansion of food yields. Despite this, microalgae have been discovered to be the most competent and unwavering source of biodiesel due to their distinguishing characteristics of being non-eatable and requiring no cropland for cultivation. The objectives of this paper was to look into the potential of a novel, formerly underappreciated biodiesel from microalgae species which could be used as a fuel substitute. Transesterification is being used to extract the biodiesel. Microalgae are blended with petroleum diesel in percentage to create microalgae blends (MAB) as needed for experimentation. The impact of biodiesel on performance as well as exhaust emission attributes of a 1-cylinder diesel engine was experimentally studied. Compared to petroleum diesel, different blend of microalgae biodiesel showed a decline in torque and hence brake power, resulting in an average fall of 7.14 % in brake thermal efficiency and 11.54 % increase in brake-specific fuel consumption. There were wide differences in exhaust emission characteristics, including carbon monoxide and hydrocarbon, as the blend ratio in diesel increased. Moreover, nitrogen oxides and carbon dioxides increase in all algae biodiesel blends, but they are still within the acceptable range of petroleum diesel.

     

Comparison of on-road emissions for B-0, B-10, and B-20 in transit buses

Biodiesels are often marketed as being cleaner than regular diesel for emissions. Emission test results depend on the biodiesel blend, but laboratory tests suggest that biodiesels decrease particulate matter, carbon monoxide, hydrocarbons, and air toxins when compared to regular diesel. Results for the amount of oxides of nitrogen (NOx) have been less conclusive. Tests have also not evaluated the commonly available ranges of biodiesel blends in the laboratory. Additionally, little information is available from on-road studies, so the effectiveness of using biodiesels to reduce actual emissions is unknown. A more complex relationship exists between engine operation and the rate of emission production than is typically evaluated using engine or chassis dynamometer tests. On-road emissions can vary dramatically because emissions are correlated to engine mode. Additionally, activity such as idling, acceleration, deceleration, and operation against a grade can produce higher emissions than more stable engine operating modes. Because these modes are not well captured in a laboratory environment, understanding on-road relationships is critical in evaluating the emissions reductions that may be possible with biodiesels. More tests and quantifications of the effects of different blends on engine and vehicle performance are required to promote widespread use of biodiesel. The objective of this research was to conduct on-road tests to compare the emission impacts of different blends of biodiesel to regular diesel fuel under different operating conditions. The team conducted on-road tests that utilized a portable emissions monitoring system that was used to instrument transit buses. Regular diesel and different blends of biodiesel were evaluated during on-road engine operation by instrumenting three in-use transit buses, from the CyRide system of Ames, Iowa, along an existing transit route.     

Effect of compression ratio,nozzle opening pressure,engine load,and butanol addition on nanoparticle emissions from a non-road diesel engine

Currently, diesel engines are more preferred over gasoline engines due to their higher torque output and fuel economy. However, diesel engines confront major challenge of meeting the future stringent emission norms (especially soot particle emissions) while maintaining the same fuel economy. In this study, nanosize range soot particle emission characteristics of a stationary (non-road) diesel engine have been experimentally investigated. Experiments are conducted at a constant speed of 1500 rpm for three compression ratios and nozzle opening pressures at different engine loads. In-cylinder pressure history for 2000 consecutive engine cycles is recorded and averaged data is used for analysis of combustion characteristics. An electrical mobility-based fast particle sizer is used for analyzing particle size and mass distributions of engine exhaust particles at different test conditions. Soot particle distribution from 5 to 1000 nm was recorded. Results show that total particle concentration decreases with an increase in engine operating loads. Moreover, the addition of butanol in the diesel fuel leads to the reduction in soot particle concentration. Regression analysis was also conducted to derive a correlation between combustion parameters and particle number emissions for different compression ratios. Regression analysis shows a strong correlation between cylinder pressure-based combustion parameters and particle number emission.

     

Regulated and unregulated emissions from a diesel engine fueled with biodiesel and biodiesel blended with methanol

Experiments were carried out on a diesel engine operating on Euro V diesel fuel, pure biodiesel and biodiesel blended with methanol. The blended fuels contain 5%, 10% and 15% by volume of methanol. Experiments were conducted under five engine loads at a steady speed of 1800 rev min⁻¹ to assess the performance and the emissions of the engine associated with the application of the different fuels. The results indicate an increase of brake specific fuel consumption and brake thermal efficiency when the diesel engine was operated with biodiesel and the blended fuels, compared with the diesel fuel. The blended fuels could lead to higher CO and HC emissions than biodiesel, higher CO emission but lower HC emission than the diesel fuel. There are simultaneous reductions of NO_x and PM to a level below those of the diesel fuel. Regarding the unregulated emissions, compared with the diesel fuel, the blended fuels generate higher formaldehyde, acetaldehyde and unburned methanol emissions, lower 1,3-butadiene and benzene emissions, while the toluene and xylene emissions not significantly different.     

Particulate Emissions from a Stationary Engine Fueled with Ultra-Low-Sulfur Diesel and Waste-Cooking-Oil-Derived Biodiesel

ABSTRACT

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture.

IMPLICATIONS There has been an increased usage of stationary diesel engines, especially backup power generators to meet the growing energy demand. Biodiesel derived from waste cooking oil has received increasing attention as an alternative fuel. However, data are only sparsely available in the literature on particulate emissions from stationary engines, fueled with blends of diesel and biodiesel. This study provides insights into the influence of waste-cooking-oil-derived biodiesel on engine performance and the particulate emissions from a stationary engine. The results of the study form a scientific basis to evaluate the impact of biodiesel emissions on the environment and human health.     

Effects of biodiesel on emissions of regulated air pollutants and polycyclic aromatic hydrocarbons under engine durability testing

An 80,000-km durability test was performed on two engines using diesel and biodiesel (methyl ester of waste cooking oil) as fuel in order to examine emissions resulting from the use of biodiesel. The test biodiesel (B20) was blended with 80% diesel and 20% methyl ester derived from waste cooking oil. Emissions of regulated air pollutants, including CO, HC, NO_x, particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) were measured at 20,000-km intervals. The identical-model engines were installed on a standard dynamometer equipped with a dilution tunnel used to measure the pollutants. To simulate real-world driving conditions, emission measurements were made in accordance with the United States Environmental Protection Agency (USEPA) FTP transient cycle guidelines. At 0 km of the durability test, HC, CO and PM emission levels were lower for the B20 engine than those for diesel. After running for 20,000 km and longer, they were higher. However, the deterioration coefficients for these regulated air pollutants were not statistically higher than 1.0, implying that the emission factors do not increase significantly after 80,000 km of driving. Total (gaseous+particulate phase) PAH emission levels for both B20 and diesel decreased as the driving mileage accumulated. However, for the engine using B20 fuel, particulate PAH emissions increased as engine mileage increased. The average total PAH emission factors were 1097 and 1437 μg bhp h⁻¹ for B20 and diesel, respectively. For B20, the benzo[a]pyrene equivalence emission factors were 0.77, 0.24, 0.20, 7.48, 5.43 and 14.1 μg bhp h⁻¹ for 2-, 3-, 4-, 5-, 6-ringed and total PAHs. Results show that B20 use can reduce both PAH emission and its corresponding carcinogenic potency.     

Techno-economic assessment of coconut biodiesel as a potential alternative fuel for compression ignition engines

Over the past years, there were dramatic improvements in identifying and assessing various feedstocks for the production of biodiesel fuels. To promote a particular feedstock as a renewable source of energy, it is important to analyze their energy, economic, and engine performance characteristics. The current work attempts to evaluate the net energy and economic indices for both fossil diesel and coconut-blended diesel (B20) considering the diesel consumption by the Indian railways. Further, we present the experimental results of a multi-cylinder diesel engine operated with neat coconut biodiesel (B100) and fossil diesel at various load and speed conditions. The engine experiments reveal that the coconut biodiesel exhibits leaner combustion and shorter ignition delay than fossil diesel. Lower amount of carbon monoxide, hydrocarbon, and smoke emission is observed in the case of coconut biodiesel, with higher levels of nitric oxide (14%) and fuel consumption than diesel. The coefficient of variation in indicated mean effective pressure is within the range of better driveability zone for both the fuels at all test conditions. Overall the engine performance, emission and combustion results with neat coconut biodiesel are favorable with a penalty in NO emission at high load conditions. The techno-economical study highlights higher production cost per liter of B20 than the cost of fossil diesel. However, the net energy ratio (NER) for B20 is 1.021, favoring higher output than diesel and thus lowers the dependency on crude oil.

     

Study of Miller timing on exhaust emissions of a hydrotreated vegetable oil (HVO)-fueled diesel engine

The effect of intake valve closure (IVC) timing by utilizing Miller cycle and start of injection (SOI) on particulate matter (PM), particle number, and nitrogen oxide (NO_x) emissions was studied with a hydrotreated vegetable oil (HVO)-fueled nonroad diesel engine. HVO-fueled engine emissions, including aldehyde and polyaromatic hydrocarbon (PAH) emissions, were also compared with those emitted with fossil EN590 diesel fuel. At the engine standard settings, particle number and NO_x emissions decreased at all the studied load points (50%, 75%, and 100%) when the fuel was changed from EN590 to HVO. Adjusting IVC timing enabled a substantial decrease in NO_x emission and combined with SOI timing adjustment somewhat smaller decrease in both NO_x and particle emissions at IVC??50 and??70 °CA points. The HVO fuel decreased PAH emissions mainly due to the absence of aromatics. Aldehyde emissions were lower with the HVO fuel with medium (50%) load. At higher loads (75% and 100%), aldehyde emissions were slightly higher with the HVO fuel. However, the aldehyde emission levels were quite low, so no clear conclusions on the effect of fuel can be made. Overall, the study indicates that paraffinic HVO fuels are suitable for emission reduction with valve and injection timing adjustment and thus provide possibilities for engine manufacturers to meet the strictening emission limits.

Implications: NO_x and particle emissions are dominant emissions of diesel engines and vehicles. New, biobased paraffinic fuels and modern engine technologies have been reported to lower both of these emissions. In this study, even further reductions were achieved with engine valve adjustment combined with novel hydrotreated vegetable oil (HVO) diesel fuel. This study shows that new paraffinic fuels offer further possibilities to reduce engine exhaust emissions to meet the future emission limits.

Supplementary Materials: Supplementary materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for a complete list of analysed PAH compounds.     

Effects of water-emulsified fuel on a diesel engine generator’s thermal efficiency and exhaust

Water-emulsified diesel has proven itself as a technically sufficient improvement fuel to improve diesel engine fuel combustion emissions and engine performance. However, it has seldom been used in light-duty diesel engines. Therefore, this paper focuses on an investigation into the thermal efficiency and pollution emission analysis of a light-duty diesel engine generator fueled with different water content emulsified diesel fuels (WD, including WD-0, WD-5, WD-10, and WD-15). In this study, nitric oxide, carbon monoxide, hydrocarbons, and carbon dioxide were analyzed by a vehicle emission gas analyzer, and the particle size and number concentration were measured by an electrical low-pressure impactor. In addition, engine loading and fuel consumption were also measured to calculate the thermal efficiency. Measurement results suggested that water-emulsified diesel was useful to improve the thermal efficiency and the exhaust emission of a diesel engine. Obviously, the thermal efficiency was increased about 1.2 to 19.9%. In addition, water-emulsified diesel leads to a significant reduction of nitric oxide emission (less by about 18.3 to 45.4%). However, the particle number concentration emission might be increased if the loading of the generator becomes lower than or equal to 1800 W. In addition, exhaust particle size distributions were shifted toward larger particles at high loading. The consequence of this research proposed that the water-emulsified diesel was useful to improve the engine performance and some of exhaust emissions, especially the NO emission reduction.

Implications:The accumulated test results provide a good basis to resolve the corresponding pollutants emitted from a light-duty diesel engine generator. By measuring and analyzing transforms of exhaust pollutant from this engine generator, the effects of water-emulsified diesel fuel and loading on emission characteristics might be more clear. Understanding reduction of pollutant emissions during the use of water-emulsified diesel helps improve the effectiveness of the testing program. The analyzed consequences provide useful information to the government for setting policies to curb pollutant emissions from a light-duty diesel engine generator more effectively.     

A study on emission performance of a diesel engine fueled with five typical methyl ester biodiesels

As an alternative and renewable fuel, biodiesel can effectively reduce diesel engine emissions, especially particulate matter and dry soot. However, the biodiesel effects on emissions may vary as the source fuel changes. In this paper, the performance of five methyl esters with different sources was studied: cottonseed methyl ester (CME), soybean methyl ester (SME), rapeseed methyl ester (RME), palm oil methyl ester (PME) and waste cooking oil methyl ester (WME). Total particulate matter (PM), dry soot (DS), non-soot fraction (NSF), nitrogen oxide (NO_x), unburned hydrocarbon (HC), and carbon monoxide (CO) were investigated on a Cummins ISBe6 Euro III diesel engine and compared with a baseline diesel fuel. Results show that using different methyl esters results in large PM reductions ranging from 53% to 69%, which include the DS reduction ranging from 79% to 83%. Both oxygen content and viscosity could influence the DS emission. Higher oxygen content leads to less DS at high load while lower viscosity results in less DS at low load. NSF decreases consistently as cetane number increases except for PME. The cetane number could be responsible for the large NSF difference between different methyl esters.     

Effect of fuel aromatic content on PAH emission from a heavy-duty diesel engine

Polycyclic aromatic hydrocarbons (PAHs) emission tests for a heavy-duty diesel engine fueled with blend base diesel fuel by adding batch fractions of poly-aromatic and mono-aromatic hydrocarbons, Fluorene and Toluene, respectively, were simulated to five steady-state modes by a DC-current dynamometer with fully automatic control system. The main objective of this study is to investigate the effect of total aromatic content and poly-aromatic content in diesel fuels on PAH emission from the HDD engine exhaust under these steady-state modes. The results of this study revealed that adding 3% and 5% (fuel vol%) Fluorene in the diesel fuel increases the amount of total-PAH emission by 2.6 and 5.7 times, respectively and increases the amount of Fluorene emission by 52.9 and 152 times, respectively, than no additives. However, there was no significant variation of PAH emission by adding 10% (vol%) of Toluene. To regulate the content of poly-aromatic content in diesel fuel, in contrast to the total aromatic content, will be more suitable for the management of PAH emission.     

Effect of additives on the stability of ethanol-diesel blends for IC engine application

The present research work was conducted on a compression ignition engine to assess the engine characteristics fueled with the blend of diesel and high-oxygenated additives such as ethanol. Ethanol does not easily blend with diesel. In order to attain a homogeneous mixture, a small amount of additive is added to the blend. Different additives were added to the blend to form a homogeneous mixture. Stability test was conducted on the blend to ensure prolonged homogeneity. The additives used for the test purpose were isopropanol, oleic acid, and ethylene acetate. From the stability results, it was found that oleic acid was the best additive which produces a better homogenous mixture for the blend of ethanol and diesel. One percentage of oleic acid is used as an additive to blend ethanol and diesel. The different combinations of blend ratios used for the test purpose were D90E10, D80E20, and D70E30. All the aforementioned blends have low cetane number because of ethanol, which was compensated by adding 1% DEE (diethyl ether) to all the blends. Experimental results exhibit that there is an improvement in the performance characteristics, such as brake thermal efficiency (BTE) and specific energy consumption (SEC), with the enrichment of DEE in ethanol-diesel blend. It is also noticed that the blend without DEE exhibited lower magnitude. This is mainly due to higher energy content and cetane number of DEE. Emission characteristics, like hydrocarbon (HC) and carbon monoxide (CO), were found to drastically increase with the increase in the ethanol concentration in the diesel blend. This is attributed to higher latent heat of vaporization (LHV) of ethanol present in the blend. Combustion pressure and heat release rate of the DEE-enriched ethanol blends were higher by 2.2 % and 2.4 %, respectively, when compared with their corresponding blends without DEE. This is a result of higher volatility of DEE which leads to better combustion.

Graphical abstract

     

Enhancement in combustion,performance, and emission characteristics of a diesel engine fueled with diesel,biodiesel, and its blends by using nanoadditive

This article presents the results of investigations carried out to evaluate the improvement in combustion, performance, and emission characteristics of a diesel engine fueled with neat petro-diesel (PD), soybean biodiesel (SB), and 50% SB blended PD (PD50SB) by using carbon nanotube (CNT) as an additive. The acid–alkaline-based transesterification process with sodium hydroxide (NaOH) as a catalyst was applied to derive the methyl ester of SB. A mass fraction of 100 ppm CNT nanoparticle was blended with base fuels by using an ultrasonicator and the physiochemical properties were measured based on EN standards. The measured physiochemical properties are in good agreement with standard limits. The experimental evaluations were carried out under varying brake mean effective pressure (BMEP) conditions in a single-cylinder, four-stroke, and natural aspirated research diesel engine at a constant speed of 1500 rpm. The results reveal that the SB and its blend promote shorter ignition delay period (IDP) that is resulting in lower in-cylinder pressure (ICP) and net heat release rate (NHR) compared to PD. The SB and its blend increase the brake specific fuel consumption (BSFC), and reduce the brake specific energy consumption (BSEC) and exhaust gas temperature (EGT), due to lower heating value, and efficient combustion, respectively. As far as the emission characteristics are concerned, the SB and its blend promote lower magnitude of hydrocarbon (HC), carbon monoxide (CO), carbon dioxide (CO₂), and smoke emissions compared to PD except for oxides of nitrogen (NO_x) emission. The CNT nanoparticle inclusion with base fuels significantly improves the combustion, performance, and emissions level irrespective of engine load conditions.

     

Characteristics of trans,trans-2,4-decadienal and polycyclic aromatic hydrocarbons in exhaust of diesel engine fueled with biodiesel

The use of biodiesel fuel as a substitute for fossil fuel in diesel engines has received increasing attention in recent years. This study is the first to investigate and compare the characteristics of mutagenic species, trans,trans-2,4-decadienal (tt-DDE), and polycyclic aromatic hydrocarbons (PAHs) in the diluted exhaust of diesel engines operated with diesel and biodiesel blend fuels. An engine of current design was operated on a dynamometer consistent with the US federal test procedure transient-cycle specifications. Petroleum diesel and a blend of petroleum diesel and biodiesel (B20) were tested. Exhaust sampling was carried out on diluted exhaust in a dilution tunnel with a constant-volume sampling system. Concentrations of tt-DDE and PAHs were analyzed by GC/MS. Although average PAH emission factors decreased from 1403 to 1051 μg bhp-h⁻¹, the results show that tt-DDE is evidently generated (1.28 μg bhp-h⁻¹) in the exhaust of diesel engine using B20 as fuel. This finding suggests that tt-DDE emission from the use of biodiesel should be taken into account in characterization and health-risk assessment. The results also show that tt-DDE is depleted in the diesel engine combustion process and the existence of tt-DDE in biodiesel is the major source of tt-DDE emission. The distribution of tt-DDE in the particulate phase is 55.3% under this study's sampling conditions. For diesel and B20, PAH phase distributions have similar trends. Lower molecular weight PAHs predominate in gaseous phase for both diesel and B20. Cold-start driving has higher tt-DDE and PAH emission factors, as well as a higher percentage of tt-DDE in particulate phase, than for warm-start driving.     

An experimental study of the influence of biofuel origin on particle-associated PAH emissions

The chemical speciation of the 16 polycyclic aromatic hydrocarbons associated to the particulate matter of conventional diesel fuel, rapeseed methyl esters, waste cooking oil methyl esters, waste cooking oil ethyl esters and their conventional fuel blends has been carried out. The speciation of these individual compounds was made by a combination of thermal extraction, solid phase micro-extraction and GC/MS analysis. This PAH speciation method was applied to a real samples obtained from a diesel engine under two different operating modes, urban and extraurban modes. The purpose of this work was to study the relationship between the amount, type and carcinogenic potency of polycyclic aromatic hydrocarbons in engine emissions and the multi-component biodiesel fuel composition.     

Diesel reformulation using bio-derived propanol to control toxic emissions from a light-duty agricultural diesel engine

In the Indian agricultural sector, millions of diesel-driven pump-sets were used for irrigation purposes. These engines produce carcinogenic diesel particulates, toxic nitrogen oxides (NOx), and carbon monoxide (CO) emissions which threaten the livelihood of large population of farmers in India. The present study investigates the use of n-propanol, a less-explored high carbon bio-alcohol that can be produced by sustainable pathways from industrial and crop wastes that has an attractive opportunity for powering stationary diesel engines meant for irrigation and rural electrification. This study evaluates the use of n-propanol addition in fossil diesel by up to 30% by vol. and concurrently reports the effects of exhaust gas recirculation (EGR) on emissions of an agricultural DI diesel engine. Three blends PR10, PR20, and PR30 were prepared by mixing 10, 20, and 30% by vol. of n-propanol with fossil diesel. Results when compared to baseline diesel case indicated that smoke density reduced with increasing n-propanol fraction in the blends. PR10, PR20, and PR30 reduced smoke density by 13.33, 33.33, and 60%, respectively. NOx emissions increased with increasing n-propanol fraction in the blends. Later, three EGR rates (10, 20, and 30%) were employed. At any particular EGR rate, smoke density remained lower with increasing n-propanol content in the blends under increasing EGR rates. NOx reduced gradually with EGR. At 30% EGR, the blends PR10, PR20, and PR30 reduced NOx emissions by 43.04, 37.98, and 34.86%, respectively when compared to baseline diesel. CO emissions remained low but hydrocarbon (HC) emissions were high for n-propanol/diesel blends under EGR. Study confirmed that n-propanol could be used by up to 30% by vol. with diesel and the blends delivered lower soot density, NOx, and CO emissions under EGR.