超临界流体技术在废旧塑料解聚中的应用

介绍了超临界流体及其特性,并综述了不同废旧塑料在超临界流体中解聚的应用现状,指出超临界解聚技术是一项处理废旧塑料的"绿色技术",为废旧塑料的回收利用开辟了新的途径,最后展望了该技术的应用前景及需要研究解决的问题.     

超临界流体技术在废旧塑料解聚中的应用

介绍了超临界流体及其特性，并综述了不同废旧塑料在超临界流体中解聚的应用现状，指出超临界解聚技术是一项处理废旧塑料的“绿色技术”，为废旧塑料的回收利用开辟了新的途径，最后展望了该技术的应用前景及需要研究解决的问题。     

聚乙烯醇在超临界水氧化中降解

以H2O2为氧化剂用间歇式超临界水氧化装置对聚乙烯醇(PVA)废水进行降解研究。通过正交实验,考察了反应温度、压力、时间及氧化剂过氧倍数对降解效果的影响,并且采用GC/MS对液相降解产物进行表征推测其可能降解途径。结果表明:PVA在SCWO体系中能完全降解,反应温度440℃、压力28 MPa、氧化剂过氧倍数4、反应40 min时,COD去除率为99.03%,出水COD=89.09 mg/L。PVA在SCWO体系中降解为烯烃、烯酮、醇和羧酸类中间产物、最终降解为小分子的饱和直链烷烃类液相产物。     

含有机物铁泥的超临界水氧化法资源化

氨基染料生产过程中产生大量含有机物的铁泥,对环境造成严重污染并造成资源的极大浪费.利用超临界水氧化法对含有机物铁泥进行资源化处理研究,并对产物进行了X射线衍射分析(XRD)、色差实验与电子探针分析.研究结果显示,用超临界水氧化法处理铁泥可以将铁泥中所含的有机物完全氧化,真正实现环境友好;超临界水首先将铁泥氧化成α-Fe2O3与γ-Fe2O3,再经过800℃煅烧后可以作为氧化铁红颜料使用;超临界反应压力对样品的晶型与颜色影响不大.     

含有机物铁泥的超临界水氧化法资源化

氨基染料生产过程中产生大量含有机物的铁泥,对环境造成严重污染并造成资源的极大浪费.利用超临界水氧化法对含有机物铁泥进行资源化处理研究,并对产物进行了X射线衍射分析（XRD）、色差实验与电子探针分析.研究结果显示,用超临界水氧化法处理铁泥可以将铁泥中所含的有机物完全氧化,真正实现环境友好;超临界水首先将铁泥氧化成α-Fe2O3与γ-Fe2O3,再经过800℃煅烧后可以作为氧化铁红颜料使用;超临界反应压力对样品的晶型与颜色影响不大.     

气封壁高浓度有机污染物超临界水氧化处理系统

利用干燥空气替换亚临界水作为蒸发壁流体,对传统蒸发壁超临界水氧化反应器进行了改进,即将干燥空气用作污染物超临界水氧化反应氧化剂的同时,又作为该超临界水氧化反应体系的密封介质,避免其与反应器内壁的直接接触,以改善超临界水氧化反应器的耐腐蚀性能。通过对采用城市活性污泥和异丙醇配制的高浓度难降解污染物悬浮液进行超临界水氧化处理后,发现反应器内衬陶瓷管在实验前后无论是外观形貌,还是结构组成均未发生明显变化;处理后液体COD降至80 mg/L以下,去除率达到99.6%以上,固体残渣量约为污染物总量的1%,且体系运行过程中压力和温度控制准确,可操作性强。进一步验证了将干燥空气作为超临界水氧化体系的密封介质具有可行性,同时表明,该气封壁超临界水氧化反应系统可用于高浓度难降解有机污染物的环境处理。     

氨的超临界水氧化研究进展

在超临界水氧化过程中,氨作为含氮有机物氧化的中间产物,其氧化是有机物在超临界水中氧化降解速率的控制步骤.综述了氧化剂、温度、过氧量、停留时间和催化剂等因素对氨的超临界水氧化降解效果的影响,并总结了目前常用的两种反应动力学模型.与双氧水或氧相比,NO-3氧化荆具有更强的氧化能力;通过提高温度、过氧量和停留时间都可以促进氨的超临界水氧化降解.在氨的超临界水氧化中,当无催化剂作用时,氨的降解率很低;加入MnO2/CeO2等催化剂,可以显著提高氨的降解率.为加快超临界水氧化法处理含氮有机废水的应用进程,未来应侧重氨氧化机制的研究和催化剂的开发.     

超/亚临界水中四溴双酚A的脱溴降解特性研究

在超/亚临界水及其碱溶液中对四溴双酚A进行了水热脱溴降解研究。考察了温度、时间和碱类型对降解特性的影响。结果表明,在纯水中温度是影响四溴双酚A降解的关键参数,350℃下反应180 min和400℃反应30 min,脱溴率分别达到98.7%和96.7%,降解产物中苯酚和4-丁基苯酚分别占50%和20%以上,另外还有少量的烷基酚;向反应体系中加入碱不仅可以中和反应过程中产生的氢溴酸以保护超临界反应釜,而且可以在较低温度下实现高的脱溴率,产物中苯酚含量达50%以上、4-异丙烯基苯酚占10%左右,可以实现脱溴同时回收化工产品的目的。与传统的热解技术相比,超/亚临界水处理TBBPA具有明显的优势,本研究为含溴电子废弃物的清洁高附加值资源化利用提供了一条新的途径。     

超临界水氧化方法处理含酚废水

在亚临界及超临界条件下,在间歇式、连续式反应器中研究了温度、压力、停留时间对苯酚去除率的影响。发现在其他条件不变的情况下,随反应温度和压力的升高,停留时间的延长,苯酚的去除率提高;在很短的停留时间内,苯酚的去除率可达９６％以上。对苯酚氧化中间产物的研究证明了该技术的氧化彻底性。     

大港油田含油污泥热解处理实验研究

采用热解法对含油污泥进行处理.经过筛选,选取活性白土作为催化剂,分别研究反应时间、反应温度、加热速率和氮气吹扫量对热解处理效果的影响.4个影响因素对液相收率的影响顺序为:氮气吹扫量＞反应温度＞反应时间＞加热速率;对反应转化率的影响顺序为:反应温度＞反应时间＞氮气吹扫量＞加热速率.实验理想的反应参数为:反应时间60min,反应温度490℃,加热速率4℃/min,氮气吹扫量90 mL/min.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.