Cr(VI)对活性污泥硝化活性的抑制及在污泥中的分布特点

重金属铬(Cr(VI))是废水中常见的、困扰很多污水生物处理系统运行效果的污染物.本文通过静态试验和静态冲击试验,研究了Cr(VI)在活性污泥系统中的分布特点和对硝化效率、活性等的影响,并进行了模型分析.结果表明,活性污泥对Cr的吸附很快,但吸附量有限,Cr(VI)投加浓度为1、5、10和30 mg · L^-1的溶液中,Cr的12 h-吸附量分别为0.79、1.98、3.19和5.78 mg · g^-1.Cr(VI)投加到活性污泥混合液中后形态分为溶解态、可洗脱和不可洗脱态,可洗脱的Cr能够向不可洗脱态转变.Cr(VI)对活性污泥硝化活性的抑制程度随着Cr(VI)浓度的增大而提高.静态试验中,1、3、5、10和30 mg · L^-1 Cr(VI)对氨氮平均降解速率的抑制率分别为5.25%、9.80%、10.41%、17.54%和21.38%.Cr(VI)对微生物的抑制作用大小是:氨氧化菌 >亚硝酸盐氧化菌 >异养菌.模型分析发现,Cr(VI)对氨氧化菌和异养菌比耗氧速率的抑制符合Haldane动力学模型,属于非竞争性抑制.冲击试验表明Cr对硝化等的抑制主要是不可洗脱的Cr造成的,抑制效果的出现具有滞后性.     

CTAB改性地聚合物同时去除Cu(II)和Cr(VI)

地聚合物（Geopolymer,简称GP）是由含硅铝酸盐的偏高岭土（Metakaolin,简称MK）或固体废料（如粉煤灰）经碱性激活制备的立体网状结构无机聚合物,对大部分重金属阳离子有良好的吸附作用,但对以阴离子形态存在的重金属吸附效果很差.本研究以偏高岭土为主要原料制备GP,同时用CTAB进行改性,研究其化学组成变化及对典型以阴、阳离子形态存在的重金属Cr（VI）和Cu（II）的同时吸附作用.结果表明,pH为5、吸附时间为24 h、初始浓度为50 mg·L^-1、吸附剂投加量为1 g·L^-1时,CTAB-GP对Cu（II）的去除率达到98.6%,Cr（VI）的最高去除率为25.6%,同时还发现溶液中Cu（II）的存在对吸附Cr（VI）有较大促进作用.整体来看,两种金属混合吸附时很好地符合二级动力学规律,单溶质吸附很好地符合Langmuir和Freundlich等温式,Cu（II）和Cr（VI）的理论最大吸附量分别为147.1 mg·g^-1和63.1 mg·g^-1.XRD、FTIR和BET表征分析结果表明,CTAB-GP中即使存在季铵盐阳离子,但依然属于地聚合物.CTAB-GP可以不牺牲对重金属阳离子吸附性能的同时吸附阴离子,优于常规地聚合物,鉴于CTAB-GP的这种特性,其在重金属污染防治中显示出极大的应用前景.     

BS+DAS复配修饰膨润土吸附Cr(Ⅵ)和Cd2+的研究

为了研究两性-阴离子复配修饰膨润土对Cr(VI)和Cd2+的吸附性能差异及其机理,并为两性复配修饰黏土矿物治理重金属污染水体提供依据,采用阴离子型有机修饰剂1-癸烷磺酸钠(DAS)复配修饰两性修饰剂十二烷基二甲基甜菜碱(BS-12或BS)修饰膨润土,研究各供试土样对Cr(VI)和Cd2+的等温吸附曲线及不同温度、pH值和离子强度条件对吸附的影响.结果表明,Langmuir模型能较好地拟合各修饰土样对不同类型重金属离子(Cr(VI)和Cd2+)的吸附曲线,其对Cr(VI)和Cd2+的平衡吸附量均呈现BS+150DAS(150%CEC DAS复配修饰膨润土)BS+100DASBS+50DASBS+25DASBSCK(膨润土)的趋势,且对Cr(VI)、Cd2+的最大吸附量(qm)分别为85.92 mmol·kg-1(100BS+150DAS)和321.89 mmol·kg-1(100BS+150DAS).各供试土样对Cr(VI)和Cd2+的吸附均表现为自发、焓增和熵增的特征,升温可增加其对Cr(VI)和Cd2+的最大吸附量.酸性环境有利于各修饰土样对Cr(VI)的吸附,而不利于对Cd2+的吸附.离子强度增加均降低了各修饰土样对Cr(VI)和Cd2+的吸附.     

Identification and characterization of the chromium（Ⅵ） responding protein from a newly isolated Ochrobactrum anthropi CTS-325

A Gram-negative, chromium(VI) tolerant and reductive strain CTS-325, isolated from a Chinese chromate plant, was identified as Ochrobactrum anthropi based on its biochemical properties and 16S rDNA sequence analysis. It was able to tolerate up to 10 mmol/L Cr(VI) and completely reduce 1 mmol/L Cr(VI) to Cr(III) within 48 h. When the strain CTS-325 was induced with Cr(VI), a protein increased significantly in the whole cell proteins. Liquid chromatography tandem mass spectrometry (LC-MS/MS) analysis revealed that this protein was a superoxide dismutase (SOD) homology. The measured superoxide dismutase activity was 2694 U/mg after three steps of purification. The SOD catalyzes the dismutation of the superoxide anion (O₂^·−) into hydrogen peroxide and molecular oxygen. This protein is considered to be one of the most important anti-oxidative enzymes for O. anthropi as it allows the bacterium to survive high oxygen stress environments, such as the environment produced during the reduction process of Cr(VI).     

Cr(VI) removal from aqueous solution with bamboo charcoal chemically modified by iron and cobalt with the assistance of microwave

Bamboo charcoal (BC) was used as starting material to prepare Co-Fe binary oxideloaded adsorbent (Co-Fe-MBC) through its impregnation in Co(NO3)2 , FeCl3 and HNO3 solutions simultaneously, followed by microwave heating. The low-cost composite was characterized and used as an adsorbent for Cr(VI) removal from water. The results showed that a cobalt and iron binary oxide (CoFe2O4 ) was uniformly formed on the BC through redox reactions. The composite exhibited higher surface area (331 m2/g) than that of BC or BC loaded with Fe alone (Fe-MBC). The adsorption of Cr(VI) strongly depended on solution pH, temperature and ionic strength. The adsorption isotherms followed the Langmuir isotherm model well, and the maximum adsorption capacities for Cr(VI) at 288 K and pH 5.0 were 35.7 and 51.7 mg/g for Fe-MBC and Co-Fe-MBC, respectively. The adsorption processes were well fitted by the pseudo second-order kinetic model. Thermodynamic parameters showed that the adsorption of Cr(VI) onto both adsorbents was feasible, spontaneous, and exothermic under the studied conditions. The spent Co-Fe-MBC could be readily regenerated for reuse.     

霉菌吸附水体中Cr(Ⅵ)Cd(Ⅱ)离子研究

采用从活性污泥中筛选的ZYL霉菌,进行吸附水体中Cr(Ⅵ)、Cd(Ⅱ)离子研究。研究结果表明:在Cr(Ⅵ)、Cd(Ⅱ)浓度分别为300mg/L时,菌种生长良好。吸附水体中[Cr(Ⅵ)、Cd(Ⅱ)]的最佳条件是pH=5.0,时间1h,温度为10℃。吸附规律符合Langm uir等温吸附模型,由回归方程得到Cr(Ⅵ)的表观最大吸附量为14m g/g;Cd(Ⅱ)的表观最大吸附量为52m g/g,说明该霉菌可以很好的去除低温水体(地下水)中Cr(Ⅵ)、Cd(Ⅱ)离子。     

Polyphenylene sulfide based anion exchange fiber: Synthesis, characterization and adsorption of Cr(VI)

A fibrous strong base anion exchanger (QAPPS) was prepared for the first time via chloromethylation and quaternary amination reaction of polyphenylene sulfide fiber (PPS), and its physical-chemical structure and adsorption behavior for Cr(VI) were characterized by FT-IR, Energy Dispersive Spectrometry, TG-DTG, elemental analysis and batch adsorptive technique, respectively. The novel fibrous adsorbent could effectively adsorb Cr(VI) over the pH range 1-12, the maximum adsorption capacity was 166.39 mg/g at pH 3.5, and the adsorption behavior could be described well by Langmuir isotherm equation model. The adsorption kinetics was studied using pseudo first-order and pseudo second-order models, and the t_1/2 and equilibrium adsorption time were 5 and 20 min respectively when initial Cr(VI) concentration was 100 mg/L. The saturated fibers could be regenerated rapidly by a mixed solution of 0.5 mol/L NaOH and 0.5 mol/L NaCl, and the adsorption capacity was well maintained after six adsorption-desorption cycles.     

铁锰复合氧化物吸附去除五价锑性能研究

对比研究了铁锰复合氧化物(FMBO)、羟基氧化铁(FeOOH)和二氧化锰(MnO₂)吸附去除五价锑(Sb(V))的性能.结果表明FMBO对Sb(V)具有很好的吸附性能,在pH=5.0的条件下,最大吸附容量达到1.05 mmol·g^-1,略高于FeOOH (0.82 mmol·g^-1)及远高于MnO₂ (0.43 mmol·g^-1);采用Freundlich模型可以很好地描述Sb(V)在FMBO的吸附行为(R² = 0.98).就吸附动力学而言,假二级动力学可很好地描述Sb(V)在FMBO (R² = 0.93)和MnO₂表面的吸附过程(R² = 0.96),而Sb(V)在FeOOH表面的吸附过程可用Elovich模型拟合 (R² = 0.94).Sb(V)的吸附量随着pH值的升高而降低;磷酸盐显著抑制了Sb(V)的吸附,而硫酸盐和碳酸盐影响不大.提高体系离子强度可促进Sb(V)在FMBO表面的吸附,推断Sb(V)在FMBO表面形成内层络合物后被吸附去除.     

锑矿冶炼区周边土壤吸附Sb (V)的行为研究

本文通过吸附平衡和动力学实验方法对Sb（V）在锑矿冶炼区周边土壤表面开展吸附行为研究,用常用的等温吸附模型和动力学吸附模型分别对等温吸附曲线和动力学吸附曲线进行拟合。结果表明：Langmuir与Freundlich模型对荒地土和林地土吸附Sb（Ⅴ）的等温吸附曲线均有较好的拟合效果,拟合系数R²0.988。荒地土对Sb（Ⅴ）的吸附能力大于林地土,其吸附量是林地土的2.9±0.2倍,这与Langmuir模型预测的该两种土壤的吸附倍数相当,荒地土表现出强烈吸附Sb（Ⅴ）的能力,尤其在锑浓度较高的体系中更为明显。结合土壤基本理化性质及矿物学特征,认为土壤秥粒、铁矿物和碳酸钙是影响土壤吸附Sb（V）的主要因素。有机质对土壤吸附Sb（Ⅴ）有一定促进作用,但这种影响只表现在Sb（Ⅴ）初始浓度低的条件下;而在Sb（Ⅴ）初始浓度高的条件下,有机质对土壤吸附Sb（Ⅴ）的影响不明显。土壤吸附Sb（Ⅴ）的过程分为快速吸附和慢速吸附两个阶段,快速反应发生在70 min以内。初始浓度低（0.01 mmol/L）的条件下,Elovich方程能够很好地拟合荒地土和林地土吸附Sb（V）的动态曲线;初始浓度高（2 mmol/L）的条件下,双常数方程对荒地土吸附Sb（V）的拟合效果较好,拟一级动力学方程和拟二级动力学方程则适用于拟合林地土吸附Sb（V）的过程。     

Simultaneous removal of Cu(II) and Cr(VI) by Mg–Al–Cl layered double hydroxide and mechanism insight

Mg–Al–Cl layered double hydroxide (Cl-LDH) was prepared to simultaneously remove Cu(II) and Cr(VI) from aqueous solution. The coexisting Cu(II) (20 mg/L) and Cr(VI) (40 mg/L) were completely removed within 30 min by Cl-LDH in a dosage of 2.0 g/L; the removal rate of Cu(II) was accelerated in the presence of Cr(VI). Moreover, compared with the adsorption of single Cu(II) or Cr(VI), the adsorption capacities of Cl-LDH for Cu(II) and Cr(VI) can be improved by 81.05% and 49.56%, respectively, in the case of coexisting Cu(II) (200 mg/L) and Cr(VI) (400 mg/L). The affecting factors (such as solution initial pH, adsorbent dosage, and contact time) have been systematically investigated. Besides, the changes of pH values and the concentrations of Mg²⁺ and Al³⁺ in relevant solutions were monitored. To get the underlying mechanism, the Cl-LDH samples before and after adsorption were thoroughly characterized by X-ray powder diffraction, transmission electron microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. On the basis of these analyses, a possible mechanism was proposed. The coadsorption process involves anion exchange of Cr(VI) with Cl⁻ in Cl-LDH interlayer, isomorphic substitution of Mg²⁺ with Cu²⁺, formation of Cu₂Cl(OH)₃ precipitation, and the adsorption of Cr(VI) by Cu₂Cl(OH)₃. This work provides a new insight into simultaneous removal of heavy metal cations and anions from wastewater by Cl-LDH.     

磁性核壳CoFe2O4@SiO2@PIL-AO复合材料的制备及其吸附U (VI)性能研究

通过化学合成法制备了磁性核壳CoFe₂O₄@SiO₂@PIL-AO复合材料,采用傅立叶变换红外光谱（FTIR）、扫描电镜（SEM）和X射线光电子能谱（XPS）对其进行了表征,研究了溶液pH、吸附时间、U （VI）初始浓度和温度等参数对U （VI）吸附性能的影响.实验结果表明：在c₀=0.2 mg·L^-1、pH=6.00±0.05、T=298.15 K、m=0.02 g和t=8 h的条件下,CoFe₂O₄@SiO₂@PIL-AO对U （VI）的吸附作用最强,吸附率达到了97.54%;CoFe₂O₄@SiO₂@PIL-AO吸附U （VI）是一个自发进行的吸热反应,U （VI）吸附动力学符合准二级动力学模型,吸附等温线符合Freundlich模型;CoFe₂O₄@SiO₂@PIL-AO复合材料具有良好的可循环使用性,循环使用5次后它对U （VI）的吸附容量没有明显下降,可重复使用.     

Antimony(V) removal from water by iron-zirconium bimetal oxide: Performance and mechanism

A Fe-Zr binary oxide adsorbent has been successfully synthesized using a co-precipitation method. It showed a better performance for antimonate (Sb(V)) removal than zirconium oxide or amorphous ferric oxide. The experimental results showed that the Fe-Zr adsorbent has a capacity of 51 mg/g at an initial Sb(V) concentration of 10 mg/L at pH 7.0. Sb(V) adsorption on the Fe-Zr bimetal oxide is normally an endothermic reaction. Most of the Sb(V) adsorption took place within 3 hr and followed a pseudo second-order rate law. Co-existing anions such as SO₄^2-, NO₃^- and Cl^- had no considerable effects on the Sb(V) removal; PO₃^4- had an inhibitory effect to some extent at high concentration; while CO_₃^2- and SiO₄^4- showed significant inhibitory effects when they existed in high concentrations. The mechanism of Sb(V) adsorption on the adsorbent was investigated using a combination of zeta potential measurements, XPS, Raman, FT-IR observations and SO₄^2- release determination. The ionic strength dependence and zeta potential measurements indicated that inner-sphere surface complexes were formed after Sb(V) adsorption. Raman and XPS observations demonstrated that both Fe-OH and Zr-OH sites at the surface of the Fe-Zr adsorbent play important roles in the Sb(V) adsorption. FT-IR characterization and SO₄^2- release determination further demonstrated that the exchange of SO₄^2- with Sb(V) also could promote the adsorption process. In conclusion, this adsorbent showed high potential for future application in Sb(V) removal from contaminated water.     

Synthesis, characterization and application of Lagerstroemia speciosa embedded magnetic nanoparticle for Cr(VI) adsorption from aqueous solution

Lagerstroemia speciosa bark (LB) embedded magnetic nanoparticles were prepared by co-precipitation of Fe²⁺ and Fe³⁺ salt solution with ammonia and LB for Cr(VI) removal from aqueous solution. The native LB, magnetic nanoparticle (MNP), L. speciosa embedded magnetic nanoparticle (MNPLB) and Cr(VI) adsorbed MNPLB particles were characterized by SEM–EDX, TEM, BET-surface area, FT-IR, XRD and TGA methods. TEM analysis confirmed nearly spherical shape of MNP with an average diameter of 8.76 nm and the surface modification did not result in the phase change of MNP as established by XRD analysis, while led to the formation of secondary particles of MNPLB with diameter of 18.54 nm. Characterization results revealed covalent binding between the hydroxyl group of MNP and carboxyl group of LB particles and further confirmed its physico-chemical nature favorable for Cr(VI) adsorption. The Cr(VI) adsorption on to MNPLB particle as an adsorbent was tested under different contact time, initial Cr(VI) concentration, adsorbent dose, initial pH, temperature and agitation speed. The results of the equilibrium and kinetics of adsorption were well described by Langmuir isotherm and pseudo-second-order model, respectively. The thermodynamic parameters suggest spontaneous and endothermic nature of Cr(VI) adsorption onto MNPLB. The maximum adsorption capacity for MNPLB was calculated to be 434.78 mg/g and these particles even after Cr(VI) adsorption were collected effortlessly from the aqueous solution by a magnet. The desorption of Cr(VI)-adsorbed MNPLB was found to be more than 93.72% with spent MNPLB depicting eleven successive adsorption–desorption cycles.     

钛基石墨烯复合材料的制备及其光催化还原Cr（VI）的研究

通过改进的Hummers法制备氧化石墨烯(GO),再将氧化石墨烯和钛酸四丁酯作为初始反应物,利用溶剂热法制备Ti O_2/RGO纳米复合材料.利用SEM、TEM、XPS、XRD等分析手段对Ti O_2/RGO纳米复合材料进行表征,考察其在可见光照射条件下光催化还原水中Cr(Ⅵ)的效能,并对光催化还原机制进行了初步探讨.结果表明,Ti O_2/RGO复合材料的光催化还原能力与单一Ti O_2(P25)相比有了显著提高;复合材料中RGO含量、溶液p H值、催化剂投加量、Cr(Ⅵ)初始浓度均对光催化还原过程有所影响,当复合材料中RGO含量比例为2%、溶液p H值为2,催化剂投加量为40 mg时,光催化还原Cr(Ⅵ)的效率可达98%.光催化还原Cr(Ⅵ)的过程是吸附过程和光催化还原过程的共同作用结果,RGO不但提高了复合材料的吸附能力,还作为复合材料的电子导体,抑制了光生电子-空穴对的复合,增强了复合材料的光催化性能.经过5次循环使用后,复合材料的光催化还原效率仍然保持在90%左右.     

氨基修饰氧化石墨烯-羧甲基纤维素复合吸附剂的制备及其对Cr (VI)的吸附性能研究

为获得价格低廉、吸附性能优良的石墨烯基吸附剂,以氧化石墨烯（GO）、羧甲基纤维素（CMC）为基材,以聚乙烯亚胺（PEI）为改性试剂,通过化学修饰的方法制备了氨基修饰氧化石墨烯-羧甲基纤维素复合吸附剂（GO-PEI-CMC）.采用扫描电镜（SEM）、傅里叶红外光谱（FT-IR）及X射线光电子能谱（XPS）等表征手段证实了CMC、氧化石墨烯与PEI已成功复合.静态吸附实验表明GO-PEI-CMC对Cr （VI）表现出良好的吸附性能,由Langmuir等温吸附模型所得最大吸附量值为243.92 mg·g^-1.吸附动力学、吸附等温线研究表明GO-PEI-CMC对Cr （VI）的吸附为单分子层、化学吸附过程.GO-PEI-CMC对Cr （VI）吸附性能优良,且具有绿色环保、可生物降解的优点,是一种极具潜力的Cr （VI）吸附剂.     

Reduced graphene oxide-nano zero value iron (rGO-nZVI) micro-electrolysis accelerating Cr(VI) removal in aquifer

Nanoscale zero-valent iron (nZVI) assembled on graphene oxide (GO) (rGO-nZVI) composites were synthesized by reduction of GO and ferrous ions with potassium borohydride, for use in Cr(VI) removal from aqueous solution. The results showed that the two-dimensional structure of GO could provide a skeleton support for Fe⁰, thus overcoming the bottleneck of aggregation for nZVI. Also, rGO-nZVI would form a ferric-carbon micro-electrolysis system in Cr(VI)-contaminated aquifers, enhancing and accelerating electron transfer, exhibiting high rate and capacity for Cr(VI) removal. The optimum dosage of the applied rGO-nZVI was linearly correlated with the initial Cr(VI) concentration. Characterization of rGO-nZVI before and after reaction with Cr(VI) revealed the process of Cr(VI) removal: rGO-nZVI firstly transferred electrons from Fe⁰ cores via their Fe(II)/Fe(III) shells to the GO sheet; there, negatively charged Cr(VI) received electrons and changed into positively charged Cr(III), which was adsorbed by the negatively charged GO sheet, avoiding the capping and passivating of nZVI. rGO-nZVI formed a good electrically conductive network, and thus had long-term electron releasing properties, which was important for groundwater remediation.     

碳基吸附剂对典型有机防晒剂二苯甲酮-3的吸附性能及热力学研究

针对环境水体中药物及个人护理用品(PPCPs)的污染问题,选择在环境水体中存在的有机紫外防晒剂二苯甲酮-3(BP-3)作为典型污染物,以颗粒活性炭(GAC)、粉末活性炭(PAC)和碳纳米管(CNT)作为吸附剂,考察吸附剂对BP-3的吸附性能、吸附特性和吸附热力学.结果表明:吸附性碳材料对BP-3具有良好的吸附性能,3种碳材料的最大吸附容量排列为:PACGACCNT,其中,PAC的单层最大吸附容量为450.36mg·g-1.Freundlich、Redlich-Peterson和Temkin吸附等温线方程能够较好地拟合吸附数据,Langmuir吸附等温线方程对PAC的吸附拟合效果较好,而对粒径较大的吸附剂(GAC、CNT)的拟合效果不理想.PAC、GAC的吸附过程可以采用一级动力学或者二级动力学模型拟合,而CNT适合采用一级动力学模型来描述.吸附热力学分析表明,PAC、GAC和CNT对BP-3的吸附过程都是自发进行的,其中,PAC和GAC的吸附过程是吸热的,升高温度有利于吸附反应的进行;而CNT的吸附过程是放热的.     

镧铁羟基氧化物修饰还原氧化石墨烯复合电极材料电吸附除磷效能及机理研究

污水处理厂尾水中低浓度PO₄^3-的排放是水体中总磷的主要来源,是导致水体富营养化的重要原因之一,对其开展深度去除的应用基础性研究具有重要的理论意义和实践价值.复合金属氧化物材料表现出较好PO₄^3-吸附能力,但仍然存在吸附速率较慢的问题.本研究采用溶剂热、复合薄膜压片法制备了镧铁羟基氧化物（LaFeO_xH_y）修饰还原氧化石墨烯（rGO）复合电极材料（LaFe-rGO）,LaFe-rGO复合电极材料显著提高了对PO₄^3-的吸附速率,5 min可达到吸附平衡,在1.2 V电压下对PO₄^3-的最大吸附量为108.69 mg·g^-1.提出了基于晶格氧提供活性位点及LaFe-rGO双电层电容电促吸附除磷机理,LaFe-rGO复合电极材料中晶格氧La-O与Fe-O同时对PO₄^3-吸附提供吸附位点,PO₄^3-与材料中的La/Fe键合以形成内球表面复合物La/Fe-PO₄,掺杂在rGO表面上的LaFeO_xH_y增加了电极材料电容并提高了其电化学活性,促进了LaFe-rGO复合电极材料对PO₄^3-的吸附.     

硫酸盐还原颗粒污泥对溶液中Cr(Ⅵ)去除特性及总Cr平衡吸附研究

利用小型EGSB反应器培养的硫酸盐还原颗粒污泥进行Cr(Ⅵ)去除实验,考察硫酸盐还原颗粒污泥对Cr(Ⅵ)的去除特性及对总Cr的平衡吸附并进行吸附等温式拟合.结果表明,颗粒污泥对Cr(Ⅵ)的去除是物理、化学及生物过程共同作用的结果,主要包括了还原及吸附作用.颗粒污泥对Cr(Ⅵ)的去除作用与环境因素、颗粒污泥的化学组成和结构的完整程度等密切相关.对Cr(Ⅵ)的去除速率随颗粒污泥投加量及Cr(Ⅵ)初始浓度的增加而提高;提高振荡速度和温度均可提高Cr(Ⅵ)的去除效率及对总Cr的吸附速率,但当振荡速度达到150r·min-1时或温度达到40℃时颗粒污泥会出现结构的离散并降低总Cr的平衡吸附量;pH值越低颗粒污泥对Cr(Ⅵ)的去除效率就越高,但颗粒污泥表面的硫化物在pH值为酸性时会转化成H2S气体逸出,并因此影响对总Cr的吸附效率.颗粒污泥对总Cr的最大吸附量为6.84mg·g-1,其对总Cr的吸附过程符合Langmuir吸附等温式.