载Pt石墨催化臭氧化降解水中草酸的研究

以石墨为催化剂载体,以H₂PtCl₆·6H₂O为贵金属活性组分前驱物,采用等体积浸渍法制备了Pt/石墨催化剂.对Pt/石墨催化臭氧化、石墨催化臭氧化以及单独臭氧氧化降解草酸的效果进行了研究.结果表明,在本实验条件下,单独臭氧氧化、石墨催化臭氧化和Pt/石墨催化臭氧化草酸的去除率分别为3.0%、47.6%和99.3%.Pt的负载可以显著地提高石墨催化臭氧化的效果.以草酸的去除效率为催化活性指标对Pt/石墨催化剂的制备条件进行了优化.结果表明,石墨载体的预处理没有提高Pt/石墨催化剂的活性.Pt/石墨催化剂最佳制备条件为：以水为溶剂,浸渍时间24　h,活性组分Pt的负载量为1.0%,氢还原温度为350℃.所制备催化剂经重复使用5次,草酸去除率仍超过90％.     

蜂窝陶瓷催化臭氧化降解水中草酸的研究

实验比较了单独臭氧氧化、蜂窝陶瓷催化臭氧化和蜂窝陶瓷催化剂吸附3种工艺去除水中草酸的降解效果.结果表明,蜂窝陶瓷催化臭氧化、单独臭氧氧化和蜂窝陶瓷催化剂吸附对水中草酸的去除率分别为37 .6%、2 .2%和0 .4%,蜂窝陶瓷催化剂的存在显著提高了臭氧氧化降解水中草酸的去除效果.添加叔丁醇的浓度为5、10和15 mg·L^-1时,催化臭氧化对草酸的去除率分别降低了24 .1%、29 .0%和30 .1%,证明蜂窝陶瓷催化臭氧化降解水中草酸遵循·OH氧化机理,即非均相的催化剂表面强化了·OH的引发.TOC测试结果显示,蜂窝陶瓷催化臭氧化工艺可以将草酸彻底矿化,无中间产物生成.反应温度与草酸的去除效果成正相关性,当水体温度为10、20、30和40℃时,蜂窝陶瓷催化臭氧化降解水中草酸的去除率分别为16 .4%、37 .6%、61 .3%和68 .2%.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

Catalytic activity of cerium-doped Ru/Al2O3 during ozonation of dimethyl phthalate

In this paper, factors influencing the mineralization of dimethyl phthalate (DMP) during catalytic ozonation with a cerium-doped Ru/Al₂O₃ catalyst were studied. The catalytic contribution was calculated through the results of a comparison experiment. It showed that doping cerium significantly enhanced catalytic activity. The total organic carbon (TOC) removal over the doped catalyst at 100 min reached 75.1%, 61.3% using Ru/Al₂O₃ catalyst and only 14.0% using ozone alone. Catalytic activity reached the maximum when 0.2% of ruthenium and 1.0% of cerium were simultaneously loaded onto Al₂O₃ support. Results of experiments on oxidation by ozone alone, adsorption of the catalyst, Ce ion’s and heterogeneous catalytic ozonation confirmed that the contribution of heterogeneous catalytic ozonation was about 50%, which showed the obvious effect of Ru-Ce/Al₂O₃ on catalytic activity. __________ Translated from China Environmental Science, 2006, 26(4): 445–448 [译自: 中国环境科学]     

不同制备方法对铝基催化剂臭氧催化氧化的效果研究

为改善混合法制备催化剂催化效率低以及浸渍法制备过程中能耗大、耗时长、成本高的问题,以混合法为基础,研究不同活性组分负载方案,并在最佳的负载方案下探究了过量浸渍法、等体积浸渍法和混合法制备的催化剂催化臭氧氧化处理石化二级出水的效果,并分析了这3种方法制备催化剂的晶型结构、比表面积、孔径和孔体积. 结果表明:①混合法负载单活性组分的催化剂在催化臭氧氧化处理石化二级出水时,Mn/Al₂O₃催化剂表现出较高的催化活性,但出水不能满足《石油化学工业污染物排放标准》(GB 31571—2015)标准中规定的排放限值;负载双活性组分的催化剂中,Mn-Cu/Al₂O₃催化剂对石化二级出水催化臭氧氧化的去除效果较好,TOC、COD和UV₂₅₄去除率分别达34.54%、49.53%和56.81%,荧光类物质中类腐殖质的去除率也达到72.34%,出水满足GB 31571—2015标准限值. ②X-射线粉末衍射仪(XRD)和比表面积分析仪(BET)的结果表明,混合法、过量浸渍法和等体积浸渍法3种方法制备的同组分催化剂均具有γ-Al₂O₃的晶型结构,吸附等温线均属于Ⅳ型等温线,吸附量最大的为过量浸渍法,达到326.37 cm3/g. ③在催化臭氧氧化石化二级出水试验中,催化活性较高的是浸渍法,混合法稍次之,但处理后出水均可满足GB 31571—2015标准限值;3种方法制备的催化剂金属离子溶出量范围均为8.74~10.15 μg/L,远低于《城镇污水处理厂污染物排放标准》(GB 18918—2002)标准中规定的排放限值. 研究显示,混合法制备催化剂在深度处理石化废水时,出水可达标排放,而混合法制备催化剂工艺简单,成本低于浸渍法. 因此,混合法在满足实际需求时,有望代替浸渍法制备臭氧催化剂.      

粒径与前驱体对活性炭催化臭氧氧化的影响

利用煤质、木质、椰壳3种前驱体活性炭制得6种粒级共18种活性炭样品,作为催化剂进行催化臭氧降解草酸的效果研究.结果表明,减小活性炭粒径对催化臭氧氧化效率提升效果显著,160~300目活性炭催化臭氧氧化降解草酸速率常数是10~20目颗粒活性炭的9.2~19.0倍.煤质160~300目活性炭催化臭氧氧化降解效果最佳.活性炭粒径的倒数与催化臭氧氧化伪一级动力学速率常数呈线性关系.对官能团的滴定表明,活性炭表面的羟基数量与催化臭氧氧化一级动力学速率常数存在较为明显的指数关系.     

臭氧催化氧化控制溴酸盐生成效能与机理

比较了单独臭氧氧化和金属氧化物存在下臭氧催化氧化过程中溴酸盐的生成规律,探讨了催化剂投量、溴离子浓度、水的pH值、反应温度等对臭氧催化氧化控制溴酸盐生成的影响规律及在催化剂存在下控制溴酸盐生成的机理.结果表明,催化剂投量从0 mg/L增加到250 mg/L,能减少溴酸盐生成量85.1%;当溴离子浓度为0.5、1.0、2.0 mg/L时,臭氧催化氧化分别能减少溴酸盐生成量69.2%、83.5%和15.2%,溴离子浓度变化对催化作用的影响无明显规律;pH值升高会降低催化作用的效果;反应温度在5～25℃之间时,臭氧催化氧化能降低43%～59%的溴酸根生成量(溴离子浓度1.5 mg/L),反应温度变化不影响催化效果.催化剂通过抑制臭氧对次溴酸的氧化减少了溴酸根的生成量.催化剂表面的某些基团与硫酸根络合会削弱臭氧催化氧化控制溴酸根生成的能力,因此,利用催化剂控制溴酸盐的机理与催化剂表面性质密切相关.     

Studies on catalytic reduction of nitrate in groundwater

Catalytic reduction of nitrate in groundwater by sodium formate over the catalyst was investigated. Pd-Cu/γ-Al₂O₃ catalyst was prepared by impregnation and characterized by brunauer-emmett-teller (BET), inductive coupled plasma (ICP), X-ray diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray (EDX). It was found that total nitrogen was effectively removed from the nitrate solution (100 mg/L) and the removal efficiency was 87%. The catalytic activity was affected by pH, catalyst amount used, concentration of sodium formate, and initial concentration of nitrate. As sodium formate was used as reductant, precise control in the initial pH was needed. Excessively high or low initial pH (7.0 or 3.0) reduced catalytic activity. At initial pH of 4.5, catalytic activity was enhanced by reducing the amount of catalyst, while concentrations of sodium formate increased with a considerable decrease in N₂ selectivity. In which case, catalytic reduction followed the first order kinetics. Translated from Acta Scientiae Circumstantiae, 2006, 26(4): 567–571 [译自: 环境科学学报]     

USY负载MnOx催崔化剂NH3选择还原NOx性能的研究

采用USY分子筛为载体制备MnOx催化剂,考察了制备方法、前躯体、焙烧温度、催化组分负载量不同的情况下NH3选择催化还原NOx的能力,同时考察了添加Fe和Ce对Mn/USY催化剂脱硝性能的影响.结果表明,采用浸渍法负载10％的醋酸锰并在500℃下焙烧所制得的催化剂,在80～320℃范围内具有很高的催化活性;Fe、Ce的...     

锰前驱体对MnO_x/TiO_2催化剂低温选择性催化还原NO_x影响

以醋酸锰和硝酸锰为前趋体通过浸渍法制备了MA和MN两种系列的MnOx/TiO2催化剂,结合BET、XRD、TPR及FT-IR等手段对催化剂进行了表征,并进行了比较,同时对两种系列的催化剂进行了选择催化还原脱硝的活性测试。结果表明,MA和MN均具有良好的低温催化活性,脱销效率随温度的变化趋势基本相同,在80℃时已经达到80%的脱硝效率;随着温度的升高,在200℃时效率上升至接近100%。通过对催化剂性能测试比较表明,锰的含量对于催化剂的活性有一定的影响。总体上看,MN具有更好的活性,脱销效率较高,并且其活动的窗口也是相对更宽,可能是因为以硝酸锰为前躯体制的的催化剂中MnO2的含量相对较多,即两类前驱体在制备过程中与载体之间的相互作用不同,导致最终催化剂表面活性组分MnOX结构和价态的不同,从而影响催化剂的低温活性。     

CuO-Ru/Al2O3 催化臭氧化降解苯乙酮的研究

采用浸渍法制备了以活性Al2O3为载体的双组分催化剂CuO-Ru/Al2O3,利用该催化剂催化臭氧化降解了苯乙酮.结果表明,贵金属钌掺杂能显著提高CuO/Al2O3催化臭氧化苯乙酮的降解效率,如在相同条件下处理30 min后,单独臭氧氧化、CuO/Al2O3/O3和CuO-Ru/Al2O3/O3对苯乙酮水溶液的COD去除率分别为6.3%、20.0%和54.0%.pH对CuO-Ru/Al2O3催化臭氧化降解苯乙酮的效率并没有影响,但与单独臭氧化相比,该催化臭氧化体系更适合在中性或酸性条件下应用.CuO-Ru/Al2O3对水中臭氧有较好的催化分解活性,臭氧分解的速率常数达2.58×10-3s-1,高于二次水中臭氧的分解速率常数1.19×10-3s-1.叔丁醇的试验结果表明,CuO-Ru/Al2O3/O3降解苯乙酮反应遵循羟基自由基(.OH)反应机制.     

Effects of tungsten oxide on the activity and thermal stability of a sulfate-derived titania supported platinum catalyst for propane oxidation

A Pt/WO₃/TiO₂ catalyst for propane oxidation was prepared by a stepwise wet impregnation method, and was aged at 800℃ for 5 hr. Compared to the sulfate-derived titania supported catalyst, the introduction of tungsten oxide as stable Bronsted acid sites led to the formation of more metallic platinum active sites at the Pt/WO₃ interface. The dissociation of surface intermediates for propane oxidation was promoted on the WO₃-modified catalyst. This, as well as the inhibition effects of tungsten oxide on the sintering of anatase and the phase transformation to rutile, resulting in a high activity and thermal stability for the Pt/WO₃/TiO₂ catalyst.     

改性贵金属催化剂催化还原脱除NO

含有NO的工业废气直接排放会严重污染空气,须对含有NO的工业废气进行净化处理.采用NH3为还原剂贵金属铂催化剂进行了低温还原NO脱除烟气中氮氧化物性能的研究.结果表明:实验室制备的贵金属铂催化剂具有高的低温活性和选择性催化还原脱除NO的性能,但该催化剂易被原料气中少量的硫化物(SO₂)中毒而影响其稳定性;用稀土元素La和Ce对贵金属铂催化剂进行改性,改性后贵金属铂催化剂的稳定性得到了大幅度提高,出口气体中氮氧化物浓度大幅度降低.本实验Pt∶La∶Ce最佳摩尔比为1∶3.78∶3.56.     

不同Cu负载量Cu-ZSM-5催化剂上正丁胺的选择催化氧化性能

采用等体积浸渍法制备不同Cu负载量(1%、2%、5%和10%)的系列Cu-ZSM-5催化剂,并考察了Cu负载量对催化剂的正丁胺催化氧化性能的影响。通过XRD、N₂吸脱附、EPR、H₂-TPR、NH₃-TPD表征方法对催化剂的晶相结构和物化性质进行表征并研究构效关系。结果表明:Cu负载量为10%的催化剂催化活性最高,在300℃下实现了正丁胺的完全转化;而Cu负载量为5%的催化剂N₂选择性最佳,低温时N₂选择性明显高于其他催化剂。表征结果表明,催化剂的氧化还原性能主要影响正丁胺的转化率,Cu负载量影响催化材料的氧化还原性能,Cu负载量高的催化剂氧化还原性能优异。高N₂选择性主要归属于催化剂孤立态Cu2+物种和弱酸性位,催化剂的弱酸性位有利于正丁胺的吸附活化和深度氧化。     

Pathway of the ozonation of 2,4,6-trichlorophenol in aqueous solution

The reaction mechanism and pathway of the ozonation of 2,4,6-trichlorophenol (2,4,6-TCP) in aqueous solution were investigated. The removal efficiency and the variation of H₂O₂, Cl⁻ formic acid, and oxalic acid were studied during the semi-batch ozonation experiments (continuous for ozone gas supply, fixed volume of water sample). The results showed that when there was no scavenger, the removal efficiency of 0.1 mmol/L 2,4,6-TCP could reach 99% within 6 min by adding 24 mg/L ozone. The reaction of molecular ozone with 2,4,6-TCP resulted in the formation of H₂O₂. The maximal concentration of H₂O₂ detected during the ozonation could reach 22.5% of the original concentration of 2,4,6-TCP. The reaction of ozone with H₂O₂ resulted in the generation of a lot of OH• radicals. Therefore, 2,4,6-TCP was degraded to formic acid and oxalic acid by ozone and OH• radicals together. With the inhibition of OH• radicals, ozone molecule firstly degraded 2,4,6-TCP to form chlorinated quinone, which was subsequently oxidized to formic acid and oxalic acid. Two reaction pathways of the degradation of 2,4,6-TCP by ozone and O₃/OH• were proposed in this study. Translated from Acta Scientiae Circumstantiae, 2005, 25(12): 1619–1623 [译自: 环境科学学报]     

钒和钨负载量对V2O5-WO3/TiO2表面形态及催化性能的影响

采用浸渍法制备了一系列不同钒和钨负载量的V₂O₅-WO₃/TiO₂催化剂样品,对样品NH₃选择性催化还原NO性能进行了评价,并用BET、XRD、XPS等手段对催化剂样品的表面形态进行了表征.研究发现,钒的负载量对催化剂的比表面积和催化活性有显著影响,当钒负载量从1％升高到8％时,催化剂比表面积下降了16 m²/g,最高活性温度降低了约100℃.钨起到稳定剂和助剂的双重作用,当钒负载量为1％时,钨负载量从0升高到6％,催化剂比表面积仅下降了3 m²/g,而活性温度窗口向高温和低温各拓宽了约50℃.研究表明钒和钨负载量都能影响催化剂表面的VO_x物种,但对催化剂的表面晶型没有明显影响.     

Size effect of Pt nanoparticles in acid-assisted soot oxidation in the presence of NO

Pt/Al₂O₃ catalysts with mean Pt particle size ranged from 2.7 to 7.1 nm were synthesized by chemical reduction method, and the sulfated counterparts were prepared by impregnation of sulfuric acid. The turnover frequency of platinum for soot oxidation under loose contact conditions in a feed flow containing NO and O₂ are positively correlated with the size of platinum. The sulfated Pt/Al₂O₃ exhibits higher catalytic activity for soot oxidation in the presence of NO despite their reduced ability for NO₂ production. Such a contradiction is more significant for those catalysts with smaller platinum particles. Herein, the catalysts were characterized by X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), transmission electron microscopy (TEM), inductive coupled plasma (ICP) emission spectrometry, CO chemisorption, thermogravimetric analysis (TGA), NH₃ temperature-programmed desorption (NH₃-TPD), NO temperature-programmed oxidation (TPO) and NO_x temperature-programmed desorption (TPD). Possible effect of Pt particle size for the catalytic oxidation of soot in the presence of NO was presented based primarily on the promoted NO₂ transfer efficiency onto the soot pushed by the acidic catalysts.     

铈掺杂Ru/Al2O3催化臭氧氧化降解邻苯二甲酸二甲酯

考察了铈(Ce)的掺杂对Ru/Al2O3催化臭氧氧化邻苯二甲酸二甲酯(DMP)溶液过程的影响.结果表明,Ce的掺杂可以显著提高臭氧氧化的效果,反应100min后,TOC的去除率可以由原催化剂的61.3%提高到75.1%,而单独臭氧氧化仅有14.0%.在实验范围内,Ru和Ce同时浸渍催化效果较好,且活性组分的溶出最少,Ce的最佳掺杂量为1.0%.通过催化剂吸附试验、单独臭氧氧化试验、Ce的均相催化试验及Ru-Se/Al2O3催化剂的非均相催化实验,证明Ru-Ce/Al2O3催化剂对DMP溶液臭氧氧化体系TOC的去除率达到50%,这是基于Ru-Ce/A12O3催化剂的非均相催化作用.     

羟基化锌催化臭氧氧化去除水中痕量磺胺嘧啶

以实验室制备的羟基化锌(ZnOOH)为催化剂,研究了其催化臭氧化去除水中痕量磺胺嘧啶(SD)的效能,通过研究叔丁醇对催化效果的影响,推断了催化反应机理,探讨了臭氧投加量、水质因素、催化剂投加量和使用次数对催化性能的影响因素.结果表明,ZnOOH对臭氧氧化水中的SD有较强的催化活性.催化剂表面结合的羟基基团有利于催化反应.在优化的实验条件下,蒸馏水中反应30min时,催化臭氧化比单独臭氧化对SD的去除率提高了47.7%.催化过程遵循自由基反应机理,SD的去除效果随催化剂投加量的增加而提高,催化剂在重复使用后催化效果基本不变,水中的氯离子可以明显降低催化剂的活性,偏碱性条件下,催化效果更佳.