双极液膜法可见光光催化降解染料废水

采用溶胶-凝胶法制备了Bi2O3-TiO2/Ti膜电极,X射线衍射(XRD)、X射线光电子能谱(XPS)、紫外-可见漫反射(DRS)和光电性能测试进行了表征,结果表明,Bi元素掺杂进入了TiO2催化剂,拓展了催化剂的光响应波长,使其在可见光下有较明显的光电响应.将Bi2O3-TiO2/Ti光阳极与Cu阴极组装成双极液膜反应器,在可见光下光催化处理活性艳红X-3B,得出当初始pH值为2.52,废水流量为80mL/min时,处理20mg/L活性艳红X-3B 150min,脱色率可达88%.双极液膜法可见光光催化的初步机理考察表明,光生电子自发由Bi2O3-TiO2表面转移到Cu电极表面,并在Cu电极表面直接还原染料,或与其表面液膜中的溶解氧反应生成H2O2,进而参与染料的氧化,由此可实现Bi2O3-TiO2/Ti的直接氧化和Cu阴极的直接还原和间接氧化的双极双效效果.     

La-PTFE共掺杂二氧化铅电极的制备及其性能研究

以Ti为基体,掺杂La2O3和聚四氟乙烯(PTFE),通过电沉积法制备了Ti/SnO2+Sb2O3/PTFE+La2O3+β-PbO2电极,并将所制备的电极应用于亚甲基蓝模拟染料废水的降解.结果发现,与常规的Ti/SnO2+Sb2O3/PTFE+β-PbO2电极相比,Ti/SnO2+Sb2O3/PTFE+La2O3+β-PbO2电极对亚甲基蓝及COD有较好的去除效果.含有La2O3活性层的Ti/SnO2+Sb2O3/PTFE+La2O3+β-PbO2电极在电解质浓度为0.15mol.L-1,电极极距为6.0cm的酸性条件下降解亚甲基蓝的效果最佳.降解3.0h后,对100mg.L-1亚甲基蓝的去除率可达到97.92%,对COD去除率为93.39%.SEM结果显示,Ti/SnO2+Sb2O3/PTFE+La2O3+β-PbO2电极表面颗粒鲜明,比表面积增大,改善了电极的微观结构和催化效果.电化学测试表明,La2O3的掺杂显著提高了二氧化铅电极的析氧过电位,显示出较好的应用前景.     

不同煅烧温度制备的Mn、N掺杂TiO2光催化性能研究

以MnSO4·H2O为锰源,尿素为氮源,采用溶胶-凝胶法制备不同锻烧温度的纯TiO2、Mn-TiO2及Mn-N-TiO2光催化剂,利用X射线衍射、紫外-可见光漫反射光谱及电子自旋共振等技术对样品形貌和结构进行表征,并以罗丹明B的光催化降解为模型反应,考察不同锻烧温度对其光催化活性的影响.结果表明,Mn、N成功掺入TiO2后,有利于提高光催化剂的热稳定性,抑制锐钛矿相向金红石相转化,且光吸收拓展到可见光区域.Mn、N共掺杂样品比单Mn掺杂样品具有更高的光催化活性,400℃下锻烧的Mn-N-TiO2在可见光下对罗丹明B的降解具有最高的光催化活性,光照2h降解率达到100%.高温锻烧Mn-N-TiO2和Mn-TiO2样品在紫外光照射30min后对罗丹明B的降解率在90%以上.     

光电催化降解苯胺的研究--外加电压的影响

以直接热氧化制备的TiO2为催化剂，研究了水中苯胺的光催化和光电催化降解行为。结果表明：外加阳极偏压可提高TiO2薄膜电极的光催化活性，但同时副反应速率增大更快，苯胺降解的光电流效率反而下降。     

Photoelectrocatalytic degradation of Rose Bengal

An innovative photoelectrode, TiO2/T1 mesh electrode, was prepared by galvanostaticanodisation. The morphology and the crystalline texture of the TiO2 film on mesh electrode were examined by scanning electronic microscopy and Raman spectroscopy respectively. The examination results indicated that the structure and properties of the film depended on anodisation rate, and the anatase was the dominant component under the controlled experimental conditions. Degradation of Rose Bengal (RB) in photocatalytic (PC) and photoelectrocatalytic (PEC) reaction was investigated, the results demonstrated that electric biasing could improve the efficiency of photecatalytic reaction. The measurement results of TOC in photoelectrocatalytic degradation showed that the mineralisation of RB was complete relatively. The comparison between the degradation efficiency of RB in PEC process and that in aqueous TiO2 dispersion was conducted. The results showed that the apparent first-order rate constant of RB degradation in PEC process was larger than that in aqueous dispersion with 0.1%--0.3% TiO2 powder, but was smaller than that in aaueaus disverslon with 1.0% TiO2.     

Kinetics of photoelectrocatalytic degradation of humic acid using B2O3·TiO2/Ti photoelectrode

An innovative photoelectrode, B₂O₃·TiO₂/Ti electrode, was prepared by galvanostaticanodisation. The morphology and crystalline texture of the B₂O₃·TiO₂ film on electrode were examined by acomic force microscopy (AFM) and X-ray diffraction respectively. The examination results indicated that the anatase was the dominant component. The kinetics of photoelectrocatalytic(PEC) degradation of humic acid(HA) was investigated; the results demonstrated that effects from strongness to weakness on the photoelectrocatalytic degraded rate of humic acid: power of UV-lamp, area of TiO₂ film, bias, original concentration of humic acid solution. The optimum conditions were power of UV-lamp 125 W, area of TiO2 film 42.0 cm² , bias 1.4 V, original concentration of humic acid solution 5 mg/L in this PEC reaction system.     

Fe-Ni-TiO2/AC粒子电极的制备及可见光光电催化协同降解RhB

制备Fe-Ni-TiO2/AC粒子电极,应用于可见光助三维电极/电Fenton(Vis-3D/EF)光电催化体系中,以RhB为目标污染物,研究了可见光光电催化对RhB的协同降解.实验优化了Fe-Ni-TiO2/AC粒子电极的制备条件,并与活性炭粒子电极、活性炭负载TiO2粒子电极在Vis-3D/EF体系中的光电催化性能进行对比,结果表明:TiO2浸渍液浓度为2g/L,Fe-Ni掺杂比为5:5,Fe:Ni:TiO2物质的量比为0.5:0.5:100的条件下制备的粒子电极在Vis-3D/EF体系中表现出最优的光电催化性能,60min对RhB的去除率达92.58%,优于活性炭粒子电极和活性炭负载TiO2粒子电极.自制粒子电极在Vis-3D/EF体系比在3D/EF体系对RhB的去除率提高29.46%,表现出明显的光催化和三维电极/电Fenton协同处理效果,协同指数为1.18,说明了自制粒子电极应用在Vis-3D/EF组合技术中,实现对RhB的可见光光电协同降解是可行的.     

铬掺杂TiO2液相沉积膜可见光下降解甲基橙研究

实验用液相沉积法制备铬掺杂改性的二氧化钛(Cr-TiO2)薄膜电极,并在可见光下利用制备的电极对甲基橙溶液(MO)进行光电降解实验研究.并对制备的薄膜进行光电流(I-t)、交流阻抗(EIS)和Mott-Schottky等电化学相关表征.当掺杂浓度为0.2％时,薄膜电极具有最好的光电催化活性.在以0.2％ Cr-TiO2...     

低温燃烧合成纳米Ni掺杂TiO2光催化剂的表征及活性研究

采用低温燃烧合成法制备了Ni掺杂TiO₂光催化剂,通过紫外-可见漫反射光谱(UV-Vis DRS)、X射线粉末衍射(XRD)、激光散射、热重-差示扫描量热分析(TG-DSC)等方法对催化剂的光吸收特性、晶相组成、粒度分布、升温过程中化学变化等进行了表征,以亚甲基蓝为模型污染物考察了催化剂在可见光下的光催化活性.结果表明,相对P25而言,Ni掺杂TiO₂的光吸收带边红移,当Ni/Ti原子比为0.4时,催化剂的带隙宽度为2.3eV,对应的吸收带边为564nm;催化剂晶型以锐钛矿TiO₂为主,随Ni掺杂量增大,NiTiO₃比例升高;催化剂粒径主要分布在50～150nm之间,占总量的96.9%;升温过程中催化剂在445.2℃发生晶型转化,出现锐钛矿和NiTiO₃晶体.催化剂显示出较高的催化活性,在可见光作用150min后最高可使93.9%的亚甲基蓝分解,活性高于P25.     

上转光剂掺杂新型纳米TiO2催化剂的制备及利用可见光降解反应艳蓝KN-R染料的研究

合成了一种新型含有稀土金属Er的上转光剂,40CdF2·60BaF2·0.8Er2O3,此上转光剂在488 nm可见光的激发下,产生了5个波长均小于387 nm的上转换紫外发射峰.采用超声波分散的方法制备出了上转光剂掺杂的纳米TiO2可见光光催化剂.采用X射线衍射(XRD)及透射电镜(TEM)对催化剂进行了表征.以反应艳蓝KN-R为研究对象,研究了在(三基色灯下发出的)可见光的照射下该可见光光催化剂的催化降解性能,并与未掺杂纳米TiO2粉末的催化剂性能进行了对比.实验结果表明,作为掺杂成分的上转光剂可有效地将可见光转化为紫外光并被纳米TiO2粉末吸收利用,在可见光照射50 h后反应艳蓝KN-R降解率达74.36%,大大高于未掺杂纳米TiO2的降解率(23.10%).     

载钛活性炭电极电吸附除盐性能的研究

采用sol-gel法制备载钛活性炭(Ti-AC),并用此活性炭制取了Ti-AC电极,利用扫描电子显微镜(SEM)、X射线荧光光谱(XRF)、X射线衍射仪(XRD)和电化学工作站等对活性炭电极的表面形貌、元素组成、化合物形态以及电极的电化学性能进行分析,并考察载钛前后活性炭电极的除盐能力,而且对Ti-AC电极与碳纳米管电极和活性炭纤维电极的实用性进行比较.结果表明,Ti-AC电极含有一定量的Ti元素,其形态为金红石型TiO2,并在电极表面积聚为很多的絮状结构,载钛后双电层形成速率更快,电吸附容量显著提高.对NaCl的吸附试验表明,Ti-AC电极物理吸附降低,电吸附明显提高,除盐率提高了62.7%.实用性分析表明,Ti-AC电极更适宜应用于电吸附除盐.     

光电化学协同催化降解甲基橙的研究

以TiO2/Ti薄膜电极为阳极、石墨电极为阴极、饱和甘汞电极为参比电极,设计了一种新型的双槽光电化学协同催化反应器,考察了阴极电位、反应时间、电解质浓度、溶液pH值等因素对甲基橙降解效果的影响.结果表明,电解质浓度对甲基橙的降解脱色效果影响不明显,而阴极电位、溶液pH值和反应时间则影响显著;色度为200度的甲基橙溶液,在阴极电位(Ec)为-0.6V、阴极槽初始pH3.0和阳极槽初始pH5.6、反应90min的条件下,阴极槽和阳极槽中甲基橙的脱色率分别为98.3%和51.3%,与仅靠TiO2/Ti薄膜阳极对有机物进行催化降解的“双槽单效”光电催化反应器相比,对甲基橙的催化氧化降解效率显著提高.降解前后的紫外-可见吸收光谱的变化表明,该双槽光电化学协同催化反应器不但可以同时使阴、阳两槽中的甲基橙脱色,且其苯环结构也被降解和矿化.     

可见光响应Pr3+:Y2SiO5/ TiO2薄膜的制备

目的研究层涂法制备Pr~(3+):Y_2SiO_5/TiO_2复合薄膜的结构与可见光催化性能。方法分别以钛酸丁酯(TBOT)和正硅酸乙酯(TEOS)为前驱体,通过溶胶-凝胶法制得TiO_2凝胶和Pr掺杂的Y_2SiO_5凝胶,以碳纤维为薄膜载体,并通过浸渍提拉法制备Pr~(3+):Y_2SiO_5/TiO_2层涂薄膜,研究层涂法制备复合薄膜对复合薄膜结构、形貌以及光催化效果的影响。结果复合薄膜具有明显的分层界限,形貌较平整,有较少龟裂;复合薄膜性能受涂覆次序的影响较大。结论依次将Pr~(3+):Y_2SiO_5和TiO_2涂覆在碳纤维上的复合薄膜具有较好的光催化性能,可见光光照2 h,对亚甲基蓝的脱色率达到94%,其可见光催化效率高于TiO_2薄膜的59%。     

A visible light-responsive iodine-doped titanium dioxide nanosphere

I-doped titanium dioxide nanospheres (I-TNSs) were synthesized via a two-step hydrothermal synthesis route, their potential for the e cient utilization of visible light was evaluated. The prepared anatase-phase I-TNSs had a bimodal porous size distribution with a Brunauer-Emmett-Teller surface area of 76 m2/g, a crystallite size of approximately 14 nm calculated from X-ray di raction data, and a remarkable absorption in the visible light region at wavelengths > 400 nm. The photocatalytic activity of the samples was evaluated by decoloration of Methyl Orange in aqueous solution under visible light irradiation in comparison to the iodine-doped TiO2 (I-TiO2). The I-TNSs showed higher photocatalytic e ciency compared with I-TiO2 after irradiation for 180 min even though the latter had a much greater surface area (115 m2/g). It was concluded that the surface area was not the predominant factor determining photocatalytic activity, and that the good crystallization and bimodal porous nanosphere structure were favourable for photocatalysis.     

花状软锰矿的超声合成及其对亚甲基蓝的脱色性能

首次通过操作简便成本低廉的超声方法合成花状软锰矿(MWs).采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)以及能量散布分析仪(EDS)等测试手段对其结构和形貌进行表征.研究了MWs对偶氮染料亚甲基蓝(MB)的脱色性能,考察pH值、反应时间、MWs投加量以及MB初始浓度等影响因子对脱色效果影响.结果表明,MWs对MB具有优良的脱色性能,90min达到近100%的脱色率,无需使用H2O2或者UV灯和超声等其它辅助设备,这明显优于其他催化剂,如Mn3O4/H2O2需3h达到99.7%最大脱色率、ZnS/CdS在光照下需6h最大脱色率仅为73%、硫改性的TiO2光照下需4h才能达到近100%的脱色率.     

光电催化降解壬基酚影响因素研究

采用sol-gel法制备TiO2薄膜光电极,以该电极为工作电极,铂丝作对电极,饱和甘汞电极为参比电极,对壬基酚的光电催化降解进行了研究。结果表明:该电极具有n型半导体的特征行为。在外加偏压为+0.8V、pH=5、、30mg/L的H2O2中对初始浓度为20mg/L的壬基酚溶液光照180min降解率达62.22%。讨论了氧的存在、外加偏压、pH等因素对光电催化反应的影响。     

Preparation of TiO2/Ti mesh photoelectrode and properties

An innovative photoelectrode,TiO2/Ti mesh electrode,was prepared by anodisation.In anodisation,0.5 mol/L H2SO4 was used as electrolytic solution,the current had been constantly 1A from the beginning of the oxidation until reaching a designed voltage.Results showed that the photocatalytic activity of electrode was better when the designed voltage was 160 V.The morphology and the crystalline texture of the TiO2 film on mesh electrode were examined by scanning electronic microseopy and Raman spectruscopy respectively.The examination results indicated that the structure and properties of the film depended on anodisation rate,and the anatase was the dominant component under the eontrolled experimental conditions.Degradation of Rhodamine B in photocatalytic (PC)and photoelectrocatalytic(PEC) reaction was investigated.     

Preparation and application of efficient TiO2/ACFs photocatalyst

Activated carbon fibers （ACFs） supported titanium dioxide （TiO2） photocatalyst was developed by sol-gel method. The surface morphology and microstructure of the photocatalyst were characterized with scan electron microscope（SEM）, X-ray diffraction patterns and specific surface area analysis. The prepared photocatalyst is specially helpful for the removal of low molecular weight organic pollutants in wastewater. Decomposition efficiency of methylene blue solution by TiO2/ACFs catalyst reached almost 100% under 60 min reaction, while the decomposition efficiency by pure TiO2 was only 25% under 3 h reaction. The mineralization of toluene aqueous solution was measured by total organic carbon instrument, and the evolution of intermediate species was detected by gas chromatograph instrument. The results indicated that the prepared photocatalyst not only enhanced the photoactivity of TiO2, but also suppressed the emergence of intermediate species, which may be more deleterious to human. The enhancement of photocatalysis was due to increased efficiency of adsorption and desorption, which were control steps in heterogeneous photocatalysis.     

钛基β-PbO2阳极催化性能及氧化机理研究

采用提拉法和电沉积法制作Ti／SnO2＋Sb2O3／β-PbO2阳极,通过SEM扫描、XRD分析和极化曲线测定表征具有良好结构和催化性能。利用该电极氧化靛红水溶液,表征Ti／SnO2＋Sb2O3／β-PbO2电极氧化机理,阳极氧化以[·OH]氧化有机物,次级氧化以阳极生成的活性相对差、寿命较长的H2O2,O3氧化有机物。Ti／SnO2＋Sb2O3／β-PbO2阳极氧化有机物是湿式氧化费用的30％～50％,具有广泛应用前景。     

Detection of intermediates in the TiO2-assisted photodegradation of Rhodamine B under visible light irradiation

The photocatalytic degradation of dye Rhodamine B （RhB） in the presence of TiO2 nanostdpe or P25 under visible light irradiation was investigated. The degradation intermediates were identified using Infrared spectra （IR spectra）, ^1H nuclear magnetic resonance （^1HNMR） spectra, and gas chromatography-mass spectroscopy （GC-MS）. The IR and the ^1HNMR results showed that the large conjugated chromophore structure of RhB was efficiently destroyed under visible light irradiation in both the photocatalytic systems （TiO2 nanostfipe or P25 and Rhodamine B systems）. GC-MS results showed that the main identified intermediates were ethanediotic acid, 1,2-benzenedicarboxylic acid, 4-hydroxy benzoic acid and benzoic acid, which were almost the same in the TiO2 nanostdpes and P25 systems. This work provides a good insight into the reaction pathway（s） for the TiO2-assisted photocatalytic degradation of dye pollutants under visible light irradiation.