锰铁复合磁性材料制备及其对零价汞吸附性能研究

燃煤工业是我国人为汞排放的主要来源,寻求合理有效的途径来控制汞排放至关重要.本文将氧化性强的过渡金属锰离子引入Mn/γ-Fe₂O₃晶格中,制备出锰铁复合磁性材料（Fe_3-xMn_x）_1-δO₄,以其来模拟Hg⁰在燃煤废气中的吸附过程,并通过比表面积和孔隙率、X衍射分析、SEM、磁性分析、氧化还原等材料表征方法研究（Fe_3-xMn_x）_1-δO₄的吸附性能,同时重点研究（Fe_3-xMn_x）_1-δO₄在不同掺杂量、温度、空速等操作条件下对Hg⁰的吸附能力.结果显示,制备所得的（Fe_3-xMn_x）_1-δO₄的比表面积均在120 m²·g^-1以上,较大的比表面积和孔体积可以为Hg⁰的吸附反应提供更多的活性区域,促进反应进行.SEM表征也显示（Fe_3-xMn_x）_1-δO₄的微观特征呈现球状颗粒物,拥有较大的表面积,能够提供更多的吸附活性位.在磁性铁氧化物中引入过渡金属锰,其对汞的氧化能力明显增强;在100~200℃的反应温度窗口,此时温度大小与（Fe_3-xMn_x）_1-δO₄对汞的吸附能力成正比,达到200℃时,500 min内平均穿透率可达到9%;空速对（Fe_3-xMn_x）_1-δO₄吸附汞的能力影响较小.     

锰氧化物负载施氏矿物去除酸性矿山废水中As(III)的性能及机理

施氏矿物是天然的砷吸附剂,但其存在酸性条件下对As(III)吸附性能较弱且无法对As(III)氧化降毒的缺陷. 采用液相沉淀法成功制备出锰氧化物负载施氏矿物(MnO_x@Sch),研究锰负载量、初始pH值和共存离子对MnO_x@Sch去除As(III)的影响,并采用吸附动力学结合XPS、FTIR及TEM等表征探究该过程的机理. 结果表明:在初始pH=3、投加量为0.5 g·L^-1、As(III)初始浓度为1 mg·L^-1的条件下,As(III)与MnO_x@Sch反应后的剩余浓度仅为2.42~3.38 μg·L^-1.MnO_x@Sch去除As(III)受初始pH影响较小,H₂PO₄^-共存时As(III)去除存在明显的抑制作用. MnO_x@Sch 去除As(III)的过程符合准二级动力学方程和颗粒内扩散方程. 液相化学组分和固相产物表征分析显示MnO_x@Sch对As(III)的去除机理可概括为As(III)氧化、静电吸附和络合配位及配体交换. 研究结果可为施氏矿物及其改性材料应用于酸性矿山废水砷污染治理提供理论依据.     

投加颗粒活性炭和二氧化锰对剩余污泥厌氧消化的影响

厌氧系统添加碳和金属纳米材料是强化厌氧消化的有效策略.为考察投加GAC和MnO₂对剩余污泥厌氧消化过程的影响,设置了空白组（R0）、GAC组（R1）、MnO₂组（R2）以及GAC/MnO₂组（R3）4组间歇实验,研究GAC和MnO₂的投加对剩余污泥厌氧消化效率、微生物活性和微生物群落结构的影响.结果表明,反应器运行28 d后,与R0相比,R1和R3的产CH₄速率分别提高了68.18%和51.35%,R2的产CH₄量降低了21.25%.GAC和MnO₂的单独或者混合投加,对厌氧发酵过程均有促进作用.Mn²⁺与剩余污泥释放的磷酸盐生成磷酸盐沉淀对厌氧代谢通道的阻塞作用,造成R2产CH₄效率变低.GAC优良导电性、吸附能力和MnO₂/Mn²⁺的催化作用是R3产CH₄效率增强的主要原因.正常代谢条件下,投加GAC、MnO₂和GAC/MnO₂均可以提高污泥厌氧消化系统微生物活性.微生物群落分析表明,GAC和MnO₂促进了产甲烷菌Methanobacterium和Methanosaeta的富集,强化了发酵细菌和产甲烷菌的种间电子传递,促进了剩余污泥厌氧发酵过程和CH₄的产生.     

ZnMnxCo2-xO4活化过一硫酸盐降解有机污染物

分别以Zn（CH₃COO）₂·2H₂O、Mn（CH₃COO）₃·2H₂O和Co（CH₃COO）₂·4H₂O为锌源、锰源和钴源,采用溶胶-凝胶自燃烧法成功制备了ZnMn_xCo_2-xO₄（x=0~2）复合物,并用X射线衍射和X射线光电子能谱对其进行表征.同时,还研究了Mn/Co物质的量比、催化剂用量及PMS用量对目标污染物降解的影响.结果表明,该复合物可催化活化过一硫酸钾（PMS）降解有机污染物,当催化剂中x=0.8,催化剂投加量为0.2 g·L^-1,PMS用量为0.4 mmol·L^-1（0.25 g·L^-1）时,20 μmol·L^-1（10 mg·L^-1）罗丹明B（RhB）可在15 min内完全降解.ZnMn_0.8Co_1.2O₄的高催化活性主要归功于Mn³⁺和Co²⁺的协同效应.将ZnMn_xCo_2-xO₄-PMS体系用于亚甲基蓝、结晶紫、金橙、双酚A、4-氯酚等其他污染物的降解,也取得了较好的效果.基于电子自旋共振ESR和自由基猝灭实验的结果,可以推测该反应体系中活性物种为硫酸根自由基和羟基自由基.     

Mercury oxidation and adsorption characteristics of potassium permanganate modified lignite semi-coke

The adsorption characteristics of virgin and potassium permanganate modified lignite semi-coke (SC) for gaseous Hg⁰ were investigated in an attempt to produce more effective and lower price adsorbents for the control of elemental mercury emission. Brunauer-Emmett-Teller (BET) measurements, X-ray powder diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to analyze the surface physical and chemical properties of SC, Mn-SC and Mn-H-SC before and after mercury adsorption. The results indicated that potassium permanganate modification had significant influence on the properties of semi-coke, such as the specific surface area, pore structure and surface chemical functional groups. The mercury adsorption efficiency of modified semi-coke was lower than that of SC at low temperature, but much higher at high temperature. Amorphous Mn⁷⁺, Mn⁶⁺ and Mn⁴⁺ on the surface of Mn-SC and Mn-H-SC were the active sites for oxidation and adsorption of gaseous Hg⁰, which oxidized the elemental mercury into Hg²⁺ and captured it. Thermal treatment reduced the average oxidation degree of Mn^x+ on the surface of Mn-SC from 3.80 to 3.46. However, due to the formation of amorphous MnO_x, the surface oxidation active sites for gaseous Hg⁰ increased, which gave Mn-H-SC higher mercury adsorption efficiency than that of Mn-SC at high temperature.     

电场与MnxCey催化剂在苯氧化反应中的协同效应及机理探究

挥发性有机物（VOCs）大量排放已成为日益严重的环境问题,为了实现VOCs的高效去除,本文采用自蔓延燃烧合成法制备了一系列锰铈复合氧化物催化剂,将稳恒直流电场引入典型VOCs气体苯的催化氧化过程,并基于不同电场条件下催化剂的理化性质表征结果进行机理分析.实验结果表明,Mn_xCe_y催化剂对含苯废气的去除有良好的效果,稳恒直流电场显著促进了催化剂的活性,其中Mn₁Ce₃的催化性能最佳,电流为5 mA时,Mn₁Ce₃催化剂在155℃可达到50%的苯转化率,在202.4℃可达到90%的苯转化率,对应的转化温度T₅₀和T₉₀比传统方法分别降低了62.4℃和48.3℃,且电场中的反应活化能由52.32 kJ·mol^-1降低至32.31 kJ·mol^-1.根据实验现象及表征结果,发现协同效应与活性位点的快速持续再生及活性氧物种的转化有关,由此提出苯在Mn_xCe_y催化剂上的氧化机理及电场协同催化的反应模型.     

CTAB改性蒙脱石负载锰氧化物催化剂的原位生长法制备及其低温SCR脱硝活性研究

以十六烷基三甲基溴化铵（CTAB）改性的有机蒙脱石（OMMT）为载体,采用原位生长法一步合成负载型锰氧化物催化剂（MnO_x/OMMT-SP）,并应用于低温NH₃-SCR脱硝反应.考察了表面有机官能团对催化剂脱硝活性的影响,发现载体表面有机官能团对催化剂的低温SCR活性具有显著的抑制作用.对有机蒙脱石载体负载锰氧化物前后分别进行热处理以去除表面有机官能团,可有效提高催化剂活性.同时,通过XRD、SEM、TEM、BET、XPS、TG、NH₃-TPD和H₂-TPR等表征手段对催化剂的结构和及理化特性进行了表征.结果表明,在原位生长法制备催化剂的过程中,有机官能团的存在主要影响了前驱体物种在载体表面的原位反应,从而影响了活性物种的化学性质;其次,有机官能团本身也对SCR反应具有抑制作用,但影响较小.分析发现,有机官能团的存在抑制了原位生长过程中Mn⁴⁺的生成,而将催化剂在氧气氛围下进行煅烧 处理,不但使催化剂的比表面积大幅提升,而且增加了其Mn⁴⁺比例,可显著增强催化剂的酸中心数量及氧化还原能力.     

VOx-MnOx/TiO2催化脱除氮氧化物与二英研究

二英会降低人类的免疫力,影响人体和神经发育;氮氧化物则会对人体的各项脏器和血液组织有严重危害,还会破坏臭氧层,加速酸雨的形成.商业钒钛催化剂既能脱除氮氧化物又能催化分解二英（邻二氯苯作为模拟物）,二英活性温度区为200~300℃,而脱硝活性温度为300~400℃.研究了VO_x/TiO₂、MnO_x/TiO₂以及VO_x-MnO_x/TiO₂等催化剂在200~300℃脱硝、脱除二英的情况.结果表明,在VO_x/TiO₂催化剂中掺入MnO_x促进脱硝活性温度区间由300~400℃往200~300℃偏移,当MnO_x和VO_x摩尔比为3：1时,催化剂在250℃脱硝和脱除二英的效果最好,催化NO和邻二氯苯效率分别为92.0%和89.0%.原位红外漫反射光谱研究表明,1V3M/T催化剂表面的脱硝反应在250℃遵循L-H机理,—NH₂、N_xH_yO_z、单齿亚硝酸盐和二齿硝酸盐是主要的反应中间体.     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NO_x) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition,NO_xwas suppressedwith the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NO_x suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

Mn含量对Mn/ZSM-5催化剂脱硝和SO2氧化性能的影响

为研究不同Mn含量对Mn基催化剂上SO₂氧化特性的影响,采用湿式浸渍法制备了一系列不同Mn含量的Mn/ZSM-5催化剂,并研究了这些催化剂上SO₂的氧化及脱硝特性,利用一系列表征手段研究了Mn/ZSM-5催化剂的物化特性和SO₂氧化机理.结果表明：①在标准SCR（选择性催化还原）反应中,随着Mn含量和温度的升高,SO₂氧化率先增后减,并在300℃时达最大值.②在快速SCR反应中,NO₂会直接氧化SO₂,提高了SO₂的氧化率,300℃时SO₂氧化率达到最高值（0.76%）.③脱硝性能试验表明,随着温度的升高,NO_x转化率呈先升后降的特征,在快速SCR反应中NO₂促进了氧化还原反应的进行,9Mn（Mn含量为9%）催化剂在250℃时NO_x转化率达最大值（96.58%）,远高于标准SCR反应的NO_x转化率.④表征结果表明,增加Mn含量提高了晶格氧和Mn⁴⁺的含量,使SO₂氧化率和NO_x转化率均增加;但过高的Mn含量会导致催化剂表面活性物质积聚,导致晶格氧和Mn⁴⁺含量下降,从而降低锰基催化剂的氧化还原性能.研究显示,在实际运行温度范围（150~400℃）内,应选择合适的Mn含量的催化剂,保证较高的脱硝效率,降低SO₂的氧化率.     

脉冲介质阻挡放电下MnOx-CeO2催化氧化碳烟的关键表面物种研究

采用柠檬酸络合法制备了Mn/(Mn+Ce)原子比为0.4的MnO_x-CeO_2复合氧化物,使其分别在有和无脉冲介质阻挡放电条件下,多次催化氧化碳烟.采用XRD、BET、Raman和XPS对新制备未反应过的和各次反应后的MnO_x-CeO_2进行表征.结果发现,在初次反应中,脉冲介质阻挡放电对反应具有强化作用,使MnO_x-CeO_2具备更好的活性.在放电和无放电2种条件下,催化剂第2次反应的活性均较第1次有所降低,且放电条件下降幅更大,而在第3次反应时催化剂活性在两种条件下均保持稳定状态.以上现象原因为,初次反应,两种条件下高温使MnO_x-CeO_2中Mn-Ce-O固溶体发生相分离,部分Mn析出生成了Mn_3O_4;未引入放电时催化剂表面发生不可逆还原的Mn~(4+)量更少,且拥有更多Ce~(3+)并产生了本征氧空位及更多的表面氧;放电的引入,加剧了初次反应时MnO_x-CeO_2表面Mn~(4+)向Mn~(3+)和Mn~(2+)的转化,使其具备更高的活性,但也抑制了Mn~(4+)的恢复,降低了催化剂的活性.在随后的反应中,有无放电催化剂均保持了稳定.脉冲介质阻挡放电对MnO_x-CeO_2反应的关键因素Mn~(4+)、本征氧空位和表面氧产生了重要影响,这种影响在初次反应时并不可逆,进而减弱了放电对反应的强化作用,该现象不可忽视,值得进一步研究.     

Removal of pharmaceutical in a biogenic/chemical manganese oxide system driven by manganese-oxidizing bacteria with humic acids as sole carbon source

Bioaugmented sand filtration has attracted considerable attention because it can effectively remove contaminants in drinking water without additional chemical reagent addition. In this study, a synthesized chemical manganese dioxide (MnO₂)-coated quartz sand (MnQS) and biogenic manganese oxide (BioMnO_x) composite system was proposed to simultaneously remove typical pharmaceutical contaminants and Mn²⁺. We demonstrated a manganese-oxidizing bacterium, Pseudomonas sp. QJX-1, could oxidize Mn²⁺ to generate BioMnO_x using humic acids (HA) as sole carbon source. The coaction of MnQS, QJX-1, and the generated BioMnO_x in simultaneously removing caffeine and Mn²⁺ in the presence of HA was evaluated. We found a synergistic effect between them. MnQS and BioMnO_x together significantly increased the caffeine removal efficiency from 32.8% (MnQS alone) and 21.5% (BioMnO_x alone) to 61.2%. Meanwhile, Mn²⁺ leaked from MnQS was rapidly oxidized by QJX-1 to regenerate reactive BioMnO_x, which was beneficial for continuous contaminant removal and system stability. Different degradation intermediates of caffeine oxidized by MnQS and BioMnO_x were detected by LC-QTOF-MS analysis, which implied that caffeine was oxidized by a different pathway. Overall, this work promotes the potential application of bioaugmented sand filtration in pharmaceutical removal in the presence of natural organic matter in drinking water.     

不同SAPO分子筛负载MnOx催化剂的低温NH3-SCR性能研究

以磷酸硅铝分子筛SAPO-5、SAPO~(-1)1和SAPO-34为载体,采用乙醇分散法制备了用于低温氨选择性还原(NH_3-SCR)NO_x的分子筛负载MnO_x催化剂.活性测试结果显示,3种分子筛催化剂均展现出优良的NH_3-SCR活性,但三者在低温区间的SCR活性存在较明显差异,其SCR活性顺序如下:MnO_x/SAPO-34MnO_x/SAPO-5MnO_x/SAPO~(-1)1.借助XRD、N2吸附-脱附、XPS、H2-TPR、NH_3-TPD、NH_3FT-IR等技术对催化剂的表面活性物种及表面酸性等进行表征分析,结果表明,MnO_x主要以无定型状态分散于载体上,负载后载体的比表面积和孔体积均有所下降.XPS和H2-TPR分析证实,不同分子筛载体上MnO_x的表面浓度与氧化态明显不同.NH_3-TPD和NH_3FT-IR分析揭示了催化剂表面均存在Bronsted酸位和Lewis酸位,其中,Lewis酸性位对低温SCR反应起着关键作用.研究表明,催化剂的催化性能会因载体不同而存在差异,高Mn4+表面浓度和丰富的Lewis酸性位对催化剂在低温区间实现优良的催化活性尤为重要.     

Highly catalytic activity of Mn/SBA-15 catalysts for toluene combustion improved by adjusting the morphology of supports

Rod-like, hexagonal and fiber-like SBA-15 mesoporous silicas were synthesized to support MnO_x for toluene oxidation. This study showed that the morphology of the supports greatly influenced the catalytic activity in toluene oxidation. MnO_x supported on rod-like SBA-15(R-SBA-15) displayed the best catalytic activity and the conversion at 230°C reached more than 90%, which was higher than the other two catalysts. MnO_x species consisted of coexisting MnO_2 and Mn_2O_3 on the three kinds of SBA-15 samples. Large amounts of Mn_2O_3 species were formed on the surface and high oxygen mobility was obtained on MnO_x supported on R-SBA-15, according to the H_2 temperature programmed reduction(H_2-TPR)and X-ray photoelectron spectroscopy(XPS) results. The Mn/R-SBA-15 catalyst with greater amounts of Mn_2O_3 species possessed a large amount of surface lattice oxygen, which accelerated the catalytic reaction rate. Therefore, the surface lattice oxygen and high oxygen mobility were critical factors on the catalytic activity of the Mn/R-SBA-15 catalyst.     

Facile synthesis of Ag-modified manganese oxide for effective catalytic ozone decomposition

O₃ decomposition catalysts with excellent performance still need to be developed. In this study, Ag-modified manganese oxides (AgMnO_x) were synthesized by a simple co-precipitation method. The effect of calcination temperature on the activity of MnO_x and AgMnO_x catalysts was investigated. The effect of the amount of Ag addition on the activity and structure of the catalysts was further studied by activity testing and characterization by a variety of techniques. The activity of 8%AgMnO_x for ozone decomposition was significantly enhanced due to the formation of the Ag_1.8Mn₈O₁₆ structure, indicating that this phase has excellent performance for ozone decomposition. The weight content of Ag_1.8Mn₈O₁₆ in the 8%AgMnO_x catalyst was only about 33.76%, which further indicates the excellent performance of the Ag_1.8Mn₈O₁₆ phase for ozone decomposition. The H₂ temperature programmed reduction (H₂-TPR) results indicated that the reducibility of the catalysts increased due to the formation of the Ag_1.8Mn₈O₁₆ structure. This study provides guidance for a follow-up study on Ag-modified manganese oxide catalysts for ozone decomposition.     

磁性纳米复合物非均相类Fenton反应催化降解罗丹明B

以锰锌铁氧体Mn0.6Zn0.4Fe2O4(Fe-MNPs)为磁核,利用正硅酸乙酯(TEOS)水解制备得到可磁分离的"核-壳"结构纳米复合物Mn0.6Zn0.4Fe2O4@Si O2(Si-Fe-MNCs),并采用X射线衍射(XRD)、N2吸附-脱附、扫描电镜(SEM)、透射电镜(TEM)、X射线光电子能谱(XPS)和振动样品磁强计(VSM)对Si-Fe-MNCs进行了表征.同时,以难生物降解染料罗丹明B(Rh B)为目标污染物,利用Si-Fe-MNCs催化过氧化氢降解Rh B,考察了不同体系、过氧化氢用量、催化剂投加量及温度等对催化活性的影响.结果表明,当温度为303 K,催化剂用量为0.5 g·L-1,过氧化氢(质量分数15%)加入量为4 m L,Rh B(20 mg·L~(-1))加入量为50 m L时,H2O2利用率为81.3%,罗丹明B降解率为95%,CODC r去除率为98.0%;自由基验证实验及XPS表征结果表明,Rh B与Si-Fe-MNCs催化H2O2产生的·OH反应而得以降解,该反应为固液界面催化反应,FeMNPs中存在的氧空位对催化反应起到协同强化作用.     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NOx) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition, NOx was suppressed with the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NOx suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.