Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NO_x) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition,NO_xwas suppressedwith the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NO_x suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide(NOx) by-products were investigated in a dielectric barrier discharge(DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide(Mn Ox), iron oxide(Fe Ox), cobalt oxide(Co Ox) and copper oxide(Cu O), supported on Al2O3/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO2 selectivity. In addition, NOx was suppressed with the decrease of specific energy density(SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the Cu O catalyst showed the best performance in NOx suppression. The Mn Ox catalyst exhibited the lowest concentration of O3 and highest CO2 selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

Highly catalytic activity of Mn/SBA-15 catalysts for toluene combustion improved by adjusting the morphology of supports

Rod-like, hexagonal and fiber-like SBA-15 mesoporous silicas were synthesized to support MnO_x for toluene oxidation. This study showed that the morphology of the supports greatly influenced the catalytic activity in toluene oxidation. MnO_x supported on rod-like SBA-15(R-SBA-15) displayed the best catalytic activity and the conversion at 230°C reached more than 90%, which was higher than the other two catalysts. MnO_x species consisted of coexisting MnO_2 and Mn_2O_3 on the three kinds of SBA-15 samples. Large amounts of Mn_2O_3 species were formed on the surface and high oxygen mobility was obtained on MnO_x supported on R-SBA-15, according to the H_2 temperature programmed reduction(H_2-TPR)and X-ray photoelectron spectroscopy(XPS) results. The Mn/R-SBA-15 catalyst with greater amounts of Mn_2O_3 species possessed a large amount of surface lattice oxygen, which accelerated the catalytic reaction rate. Therefore, the surface lattice oxygen and high oxygen mobility were critical factors on the catalytic activity of the Mn/R-SBA-15 catalyst.     

Preparation of MnO2 decorated Co3Fe1Ox powder/monolithic catalyst with improved catalytic activity for toluene oxidation

In this paper, KMnO₄ was used to pre-treat Co₃Fe-layered double hydroxides (LDH) precursor to prepare MnO₂ decorated Co₃Fe₁O_x catalyst. The toluene oxidation performance of the catalyst was investigated systematically. The optimized 0.1MnCF-LDO catalyst exhibited the best catalytic performance, and the temperatures of 50% and 90% toluene conversion (T₅₀ and T₉₀) were 218 and 243°C, respectively. The apparent activation energy (E_a) was 31.6 kJ/mol. The characterization results showed that the pre-redox reaction by KMnO₄ could increase the specific surface area, Co³⁺ species amount and oxygen defect concentration of the catalyst, which are the main reason of the improved toluene catalytic activity. Besides, this method was also applied to enhance toluene oxidation of iron mesh based monolithic catalyst. The 0.1MnCF-LDO/Iron mesh (IM) catalyst showed a 90% toluene conversion at around 316°C which was much lower than that of without MnO₂ addition (359°C). In addition, the water resistant of all the catalysts was studied as well, all the samples showed relatively good water resistance. The toluene conversion still remained to be over >80% even in the presence of 10 vol.% water vapor.     

Effects of WOx modification on the activity, adsorption and redox properties of CeO2 catalyst for NOx reduction with ammonia

A series of WO₃/CeO₂ (WOx/CeO₂) catalysts were synthesized by wet impregnation of ammonium metatungstate on a CeO₂ support. The resulting solid acid catalysts were characterized by X-ray diffraction (XRD), UV-Vis spectroscopy (UV-Vis), Raman spectroscopy (Raman), in-situ Fourier transform infrared spectroscopy (in-situ FT-IR) of ammonia adsorption, NH₃-TPD, H₂ temperature-programmed reduction (H₂-TPR), NH₃/NO oxidation and activity measurements for NOx reduction by NH₃ (NH₃-SCR). The results show that polytungstate (WOx) species are the main species of tungsten oxide on the surface of ceria. The addition of tungsten oxide enhances the Brönsted acidity of ceria catalysts remarkably and decreases the amount of surface oxygen on ceria, with strong interaction between CeO₂ and WOx. As a result, the N₂ selectivity of NH₃ oxidation and NH₃-SCR at high temperatures (> 300℃) is enhanced. Therefore, a wide working temperature window in which NOx conversion exceeds 80% (NOx conversion > 80%) from 200 to 450℃, is achieved over 10 wt.% WOx/CeO₂ catalyst. A tentative model of the NH₃-SCR reaction route on WOx/CeO₂ catalysts is presented.     

Facile synthesis of Ag-modified manganese oxide for effective catalytic ozone decomposition

O₃ decomposition catalysts with excellent performance still need to be developed. In this study, Ag-modified manganese oxides (AgMnO_x) were synthesized by a simple co-precipitation method. The effect of calcination temperature on the activity of MnO_x and AgMnO_x catalysts was investigated. The effect of the amount of Ag addition on the activity and structure of the catalysts was further studied by activity testing and characterization by a variety of techniques. The activity of 8%AgMnO_x for ozone decomposition was significantly enhanced due to the formation of the Ag_1.8Mn₈O₁₆ structure, indicating that this phase has excellent performance for ozone decomposition. The weight content of Ag_1.8Mn₈O₁₆ in the 8%AgMnO_x catalyst was only about 33.76%, which further indicates the excellent performance of the Ag_1.8Mn₈O₁₆ phase for ozone decomposition. The H₂ temperature programmed reduction (H₂-TPR) results indicated that the reducibility of the catalysts increased due to the formation of the Ag_1.8Mn₈O₁₆ structure. This study provides guidance for a follow-up study on Ag-modified manganese oxide catalysts for ozone decomposition.     

Synergistic effects of non-thermal plasma-assisted catalyst and ultrasound on toluene removal

A wire-mesh catalyst coated by La_0.8Sr_0.2MnO₃ was combined with a dielectric barrier discharge (DBD) reactor for toluene removal at atmospheric pressure. It was found that toluene removal efficiency and carbon dioxide selectivity were enhanced in the catalytic packed-bed reactor. In addition, ozone and nitrogen monoxide from the gas effluent byproducts decreased. This is the first time that ultrasound combined with plasma has been used for toluene removal. A synergistic effect on toluene removal was observed in the plasma-assisted ultrasound system. At the same time, the system increased toluene conversion and reduced ozone emission.     

Structures and catalytic performances of Me/SAPO-34 (Me = Mn, Ni, Co) catalysts for low-tem perature SCR of NOx by ammonia

Me/SAPO-34 (Me = Mn, Ni, Co) series of catalysts were prepared by a wetness impregnation method and investigated for the selective catalytic reduction of nitrogen oxides with ammonia (NH₃-SCR). Among them, Mn/SAPO-34 catalyst was found as the most promising candidate based on its superior low-temperature activity. The catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy images (TEM), nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction and desorption (TPR and TPD), and diffuse reflectance infrared Fourier transformed spectroscopy (DRIFTS) of NH₃/NO_x adsorption. Mn/SAPO-34 is obviously different from Ni/SAPO-34 and Co/SAPO-34 in the active species state and distribution. Surface MnO_x species which play an essential role in NO oxidation and NO₂ adsorption, act as better active sites than nickel and cobalt mostly in the form of the aluminates and silicates.     

Improvement of the activity and SO2 tolerance of Sb-modified Mn/PG catalysts for NH3-SCR at a low temperature

A series of MnM/palygorskite (PG) (M = La, W, Mo, Sb, Mg) catalysts was prepared by the wetness co-impregnation method for low-temperature selective catalytic reduction (SCR) of NO with NH₃. Conversion efficiency followed the order Sb > Mo > La > W > Mg. A combination of various physico-chemical techniques was used to investigate the influence of Sb-modified Mn/PG catalysts. MnSb_0.156/PG catalyst showed highest NO conversion at low temperatures in the presence of SO₂ which reveals that addition of Sb oxides effectively enhances the SCR activity of catalysts. A SO₂ step-wise study showed that MnSb_0.156/PG catalyst displays higher durable resistance to SO₂ than Mn/PG catalyst, where the sulfating of active phase is greatly inhibited after Sb doping. Scanning electron microscopy and X-ray diffraction results showed that Sb loading enhances the dispersion of Mn oxides on the carrier surface. According to the results of characterization analyses, it is suggested that the main reason for the deactivation of Mn/PG is the formation of manganese sulfates which cause the permanent deactivation of Mn-based catalysts. For Sb-doped Mn/PG catalyst, SO_x ad-species formed were mainly combined with SbO_x rather than MnO_x. This preferential interaction between SbO_x and SO₂ effectively shields the MnO_x as active species from being sulfated by SO₂ resulting in the improvement of SO₂ tolerance on Sb-added catalyst. Multiple information support that, owing to the addition of Sb, original formed MnO_x crystallite has been completely transformed into highly dispersed amorphous phase accounting for higher SCR activity.     

SO2对MnOx/PG催化剂低温脱硝的影响机理研究

采用等体积浸渍法制备了锰氧化物负载凹凸棒石(MnO_x/PG)低温SCR催化剂,通过SO₂暂态响应、程序升温表面反应(TPSR)等实验技术研究了烟气中SO₂对催化剂SCR脱硝活性的影响行为.采用程序升温脱附(TPD)、BET比表面及孔径分布测定、XPS等表征技术对催化剂硫中毒的机理及化学本质进行了深入分析.结果表明,低温下烟气中SO₂对MnO_x/PG催化剂的SCR脱硝活性存在显著的抑制作用,催化剂中毒主要由烟气中SO₂的催化氧化引起.一方面SO₂氧化为SO₃后与NH₃及H₂O竞争反应形成复杂的硫酸铵盐堵塞催化剂孔道,另一方面与活性组分MnO₂结合形成MnSO₄使得部分活性组分形态发生变迁.其中硫酸铵盐的形成可通过适当的热处理得以去除,而MnSO₄则不可恢复,但催化剂SCR活性却显著增加,表明MnSO₄的形成不是催化剂失活的主要因素.吸附态的硫可显著增加催化剂表面酸性,因此对SCR活性有促进作用.催化剂失活主要机理为:由气相SO₂的连续氧化并与NH₃相结合形成硫酸铵盐,并且在低温下难以分解,以致堵塞催化剂活性中心.     

天然气-汽油双燃料车实际道路排放特性研究

为研究使用天然气对轻型汽车排放的影响,利用便携式排放测试系统（PEMS）,对25辆压缩天然气-汽油双燃料出租车在实际道路上分别使用汽油和天然气时的CO2、CO、NOx和THC排放进行了对比测试.研究结果表明：实际道路上,原装车使用天然气相比汽油时,CO2、CO的排放平均分别降低22%和24%,NOx和THC的排放平均分...     

不同SAPO分子筛负载MnOx催化剂的低温NH3-SCR性能研究

以磷酸硅铝分子筛SAPO-5、SAPO~(-1)1和SAPO-34为载体,采用乙醇分散法制备了用于低温氨选择性还原(NH_3-SCR)NO_x的分子筛负载MnO_x催化剂.活性测试结果显示,3种分子筛催化剂均展现出优良的NH_3-SCR活性,但三者在低温区间的SCR活性存在较明显差异,其SCR活性顺序如下:MnO_x/SAPO-34MnO_x/SAPO-5MnO_x/SAPO~(-1)1.借助XRD、N2吸附-脱附、XPS、H2-TPR、NH_3-TPD、NH_3FT-IR等技术对催化剂的表面活性物种及表面酸性等进行表征分析,结果表明,MnO_x主要以无定型状态分散于载体上,负载后载体的比表面积和孔体积均有所下降.XPS和H2-TPR分析证实,不同分子筛载体上MnO_x的表面浓度与氧化态明显不同.NH_3-TPD和NH_3FT-IR分析揭示了催化剂表面均存在Bronsted酸位和Lewis酸位,其中,Lewis酸性位对低温SCR反应起着关键作用.研究表明,催化剂的催化性能会因载体不同而存在差异,高Mn4+表面浓度和丰富的Lewis酸性位对催化剂在低温区间实现优良的催化活性尤为重要.     

非平衡等离子体联合技术降解甲苯气体

采用了自制的纳米钛酸钡基介电材料作为催化剂,以电工陶瓷拉西环作为载体,利用介质阻挡放电产生的非平衡态等离子体对常压下流动态含甲苯的空气进行处理,研究了电场强度、流速、初始浓度及不同填料情况下甲苯的降解及臭氧产生情况,初步探讨了等离子体催化降解甲苯的机理,并进行了产物分析.实验结果表明,电场强度小于13kV·cm-1时,甲苯降解率和臭氧产生浓度随电场强度的提高而上升,随气速和初始浓度的增加而降低;不同填料下降解率及臭氧浓度由大到小排序为有催化剂填料、普通填料、无填料,有催化剂存在时(电场强度为14kV·cm-1,流速为0.3 m3·h-1,甲苯浓度为600 mg·L-1),甲苯降解率最高可达95%.当电场强度>13kV·cm-1时,臭氧浓度因受到过量的高能电子攻击而发生分解.表现为臭氧浓度随电场强度的继续增加而降低.因此,电场强度为13kV·cm-1时,产生的臭氧浓度最高.     

Efficient degradation of chlorobenzene in a non-thermal plasma catalytic reactor supported on CeO2/HZSM-5 catalysts

Chlorobenzene removal was investigated in a non-thermal plasma reactor using CeO₂/HZSM-5 catalysts. The performance of catalysts was evaluated in terms of removal and energy efficiency. The decomposition products of chlorobenzene were analyzed. The results show that CeO₂/HZSM-5 exhibited a good catalytic activity, which resulted in enhancements of chlorobenzene removal, energy efficiency, and the formation of lower amounts of by-products. With regards to CO₂ selectivity, the presence of catalysts favors the oxidation of by-products, leading to a higher CO₂ selectivity. With respect to ozone, which is considered as an unavoidable by-product in air plasma reactors, a noticeable decrease in its concentration was observed in the presence of catalysts. Furthermore, the stability of the catalyst was investigated by analyzing the evolution of conversion in time. The experiment results indicated that CeO₂/HZSM-5 catalysts have excellent stability: chlorobenzene conversion only decreased from 78% to 60% after 75 hr, which means that the CeO₂/HZSM-5 suffered a slight deactivation. Some organic compounds and chlorinated intermediates were adsorbed or deposited on the catalysts surface as shown by the results of Fourier Transform Infrared (FT-IR) spectroscopy, scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS) analyses of the catalyst before and after the reaction, revealing the cause of catalyst deactivation.     

Selective catalytic reduction of nitrogen oxides over a modified silicoaluminophosphate commercial zeolite

Nitrogen oxides(NO_x:NO,NO_2)are a concern due to their adverse health effects.Diesel engine transport sector is the major emitter of NO_x.The regulations have been strengthened and to comply with them,one of the two methods commonly used is the selective catalytic reduction of NO_xby NH_3(NH_3-SCR),NH_3being supplied by the in-situ hydrolysis of urea.Efficiency and durability of the catalyst for this process are highly required.Durability is evaluated by hydrothermal treatment of the catalysts at temperature above 800°C.In this study,very active catalysts for the NH_3-SCR of NO_xwere prepared by using a silicoaluminophosphate commercial zeolite as copper host structure.Characterizations by X-ray diffraction(XRD),scanning electron microscopy(SEM)and temperature programmed desorption of ammonia(NH_3-TPD)showed that this commercial zeolite was hydrothermally stable up to 850°C and,was able to retain some structural properties up to950°C.After hydrothermal treatment at 850°C,the NO_xreduction efficiency into NH_3-SCR depends on the copper content.The catalyst with a copper content of 1.25 wt.%was the most active.The difference in activity was much more important when using NO than the fast NO/NO_2reaction mixture.     

铜铈复合氧化物上石化行业典型VOCs的氧化行为与动力学

采用共沉淀法和等体积浸渍法制备了CuCeO x复合催化剂,对材料的物化性质进行了XRD、低温N2吸脱附、H2-TPR和O2-TPD表征.以石化行业典型VOCs(苯、甲苯和正己烷)为探针污染物,研究了污染物组成与浓度、反应空速、O2浓度、H2O浓度和催化剂种类对其氧化行为的影响,并对反应动力学参数进行了模型拟合.共沉淀得到的催化剂具有均匀的活性相、好的低温可还原性能和较多的活性表面氧物种.甲苯氧化率随着污染物浓度升高而降低,高转化率下苯浓度与其氧化率无相关性,正己烷的氧化率与入口浓度呈正比.苯能够显著抑制甲苯的氧化,而甲苯加入有利于苯的氧化.正己烷对苯氧化的影响较小,但能够促进甲苯的转化,苯系物对正己烷氧化有明显的抑制作用.低空速和高氧浓度都有利于污染物的氧化,氧浓度的变化对正己烷和苯的氧化影响较小.水汽对甲苯的氧化有明显的抑制作用,而对苯和正己烷氧化有明显的促进作用.共沉淀催化剂具有更好的甲苯和苯氧化性能,而无水条件下浸渍催化剂具有更好的正己烷氧化性能.拟一级动力学模型能够很好地模拟不同条件下污染物的氧化行为.     

The selective catalytic reduction of NO over Ce0.3TiOx-supported metal oxide catalysts

A Ce_(0.3)TiO_xoxide carrier was synthesized via a sol–gel process,and Ce_(0.3)TiO_xsupported metal(M=Cd,Mn,Fe,W,Mo)oxide catalysts were prepared by the method of incipient-wetness impregnation.The catalysts were characterized by means of X-ray diffraction(XRD),Brunauer–Emmett–Teller(BET)analysis,scanning electron microscopy(SEM),transmission electron microscopy(TEM),Fourier transform infrared(FT–IR)spectroscopy,UV–Visdiffusereflectancespectroscopy(UV–VisDRS),and Temperature-programmed reduction with H_2(H_2-TPR).The catalytic activities for de-NO_(x )were evaluated by the NH_3-SCR reaction.Among all the catalysts tested,the 2 wt.%Cd/Ce_(0.3)TiO_xcatalyst exhibited the best NH_3-SCR performance,with a wide temperature window of 250–450°C for NO conversion above 90%.Moreover,the catalyst showed N_2 selectivity greater than 99%from 200 to 450°C.     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O³ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ >> NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the "cold start" problem.     

Heterojunctioned CuO/Cu2O catalyst for highly efficient ozone removal

In recent years, near surface ozone pollution, has attracted more and more attention, which necessitates the development of high efficient and low cost catalysts. In this work, CuO/Cu₂O heterojunctioned catalyst is fabricated by heating Cu₂O at high temperature, and is adopted as ozone decomposition catalyst. The results show that after Cu₂O is heated at 180°C conversion of ozone increases from 75.2% to 89.3% at mass space velocity 1,920,000 cm³/(g·hr) in dry air with 1000 ppmV ozone, which indicates that this heterojunction catalyst is one of the most efficient catalysts reported at present. Catalysts are characterized by electron paramagnetic resonance spectroscopy and ultraviolet photoelectron spectroscopy, which confirmed that the heterojunction promotes the electron transfer in the catalytic process and creates more defects and oxygen vacancies in the CuO/Cu₂O interfaces. This procedure of manufacturing heterostructures would also be applicable to other metal oxide catalysts, and it is expected to be more widely applied to the synthesis of high-efficiency heterostructured catalysts in the future.     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.