聚合氯化铝中纳米Al13形态的混凝效应

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al13形态,用透光率脉动检测技术并结合絮凝效能和Zeta电位测定结果,对纳米Al13形态以及PAC、AlCl3絮凝过程中絮集物形成和增长的变化差异作了对比性研究.结果表明,混凝剂的不同铝形态分布在混凝过程中起着十分重要的作用.Al13形态是在絮凝过程中起电中和作用的主要形态,可以大大增加颗粒间的有效碰撞率,其凝聚速度和所形成絮集物颗粒大小在实验条件下呈现最大值.而对于PAC,其Alc含量较高,可起到吸附架桥和网捕卷扫作用,所以在低投加量表现出较快的絮体增长速率.     

高Al13纳米聚合氯化铝的结构表征及混凝效果

采用AlCl36H2O和Na2CO3制备了聚合氯化铝(PAC),并采用SO42-/Ba2+沉淀-置换法分离提纯了其中的纳米Al13形态,应用27Al-NMR和XRD等现代实验技术对其中的Al13形态进行了分析表征,27Al-NMR结果表明,分离提纯后样品中的Al13含量明显高于PAC,XRD结果表明,Al13的衍射峰出现在2q角为5~25之间;混凝烧杯实验表明,纳米级PAC较传统的混凝剂AlCl3、Al2(SO4)3和PAC具有更好的除浊、脱色效果.     

混凝过程中絮体形貌的PIV成像观测与表征

采用粒子成像速度场仪(PIV)对Taylor-Couette反应器内的混凝过程中絮体的微观形貌进行了观测与表征.结果表明,内筒转速在20～60r/min范围内,生成的絮体颗粒较大,粒径分布均匀,絮凝沉淀效果最好.由于内筒旋转速度的变化直接导致混凝流场形态的变化,所以混凝过程中流场形态的变化对絮体生长过程有重要影响,进而直接影响到混凝效果.混凝过程中流场的周期性变化、涡间存在液体传递的波状涡结构有利于絮体颗粒的结合生长,并导致较高的絮凝沉淀去除率.这也说明PIV技术能够在测量流场的同时较好地反映混凝过程中微絮体的形貌变化特征,从而实现对絮凝过程的原位观测与表征.     

聚合氯化铝中Alb形态去除腐殖酸的效果及机制研究

Alb形态[Al12AlO4(OH)247+]是聚合氯化铝(polyaluminiurn chloride,PAC)水解-聚合作用中形成的一种粒度小、所带正电荷多、聚集程度高及分子量大的多核羟基配合物.本试验采用乙醇.丙酮混合沉淀法分离PAC溶液中各种铝形态,提纯出Alb形态(Alb絮凝剂).研究投加量、pH及无机离子对Alb絮凝剂处理腐殖酸模拟水样絮凝效果的影响,并利用光散射颗粒分析仪(PDA2000)测定Alb絮凝剂对腐殖酸絮凝过程中絮体的形成与增长过程的动态变化,结合絮体的Zeta电位,对Alb絮凝剂的絮凝机制进行了初步探讨.结果表明,当投加量为4.3～6.3 ms/L、pH值为3.0～6.0时,Alb絮凝剂处理腐殖酸模拟水样达到最佳絮凝效果;NH4+、SiO32-、H2PO4-的存在明显抑制其絮凝性能.絮凝动力学过程和絮体Zeta电位表明,Alb絮凝剂在水处理中主要是通过电中和作用和吸附网捕卷扫作用共同起絮凝作用的.     

聚合氯化铝中Al_(13)形态水解稳定性的研究

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al13形态,并采用Al-Ferron逐时络合比色法对比研究了Al13形态、PAC和Al13三种样品水解稳定性。研究结果表明Al13形态无论是对于稀释倍数、介质的pH值和水解时间都具有较高的水解稳定性,是给水和废水处理中的一种较为有效的Al形态。     

聚合氯化铝中纳米Al13电荷特性及其混凝效果

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al-Ferron逐时络合比色法和ZATESIZER 3000HSA测定仪对分离所得纳米Al₁₃形态以及AlCl₃和PAC进行了分析表征和电荷特性的对比性研究;采用烧杯实验法对3个样品处理实际和模拟水样的混凝效果进行了对比性研究.Al-Ferron逐时络合比色法的结果表明,采用层析法分离可得到含量99%左右的纳米Al₁₃形态;电荷特性和混凝效果研究结果表明纳米Al₁₃形态较其它两者具有更好的除浊、除腐殖酸和脱色效果并且具有更强的电中和能力,因此Al₁₃形态是一种具有较高正电荷和较高的水解稳定性,在给水和废水处理中的一种较为有效的Al形态.     

Al_b形态处理模拟染料废水的效果及机制研究

采用乙醇-丙酮混合沉淀法分离聚合氯化铝(PAC)溶液中的Alb形态.通过对吸光度和Zeta电位的测定,研究了Alb形态的投加量和溶液pH对分散黄棕和直接紫2种模拟染料废水脱色效果的影响,并将其与PAC进行比较.利用光散射颗粒分析仪(PDA2000)和Mastersizer2000型激光粒度仪在线测定絮体粒径的变化情况,结合絮体的Zeta电位,对Alb形态的絮凝机制进行探讨.结果表明,与PAC比较,Alb形态处理模拟染料废水的最佳pH值范围较宽,在实验条件下,Alb形态形成的絮体的密实性较高,沉降性能较好,恢复能力较强.     

混凝剂特性对建筑景观水水质维护效果的影响

建筑景观水体的水质会直接影响居民身体健康和生活环境,采用简单、高效的水质维护技术具有较大实用价值。采用混凝-沉淀法对比研究了硫酸铝(Al2(SO4)3)、聚合氯化铝(PAC)、三氯化铁(Fe Cl3)和聚合硫酸铁(PFS)4种常用混凝剂对建筑景观水体中主要污染物的去除效果,对混凝剂的电性中和特性与絮体特性进行初步分析。结果表明:在投药量为10~30 mg/L条件下PAC、PFS和Fe Cl3的混凝除污染效果均明显好于Al2(SO4)3;在投药量达到35 mg/L时,4种混凝剂的混凝效果趋于相近,均可达到较好的除污效果。由Zeta电位和絮体特性的分析可知:PAC电荷密度最高,PAC和PFS形成的絮体粒径和密度最佳。     

Al13形态的凝胶层析分离及分离级分特性对比

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al- Ferron逐时络合比色法、透射电镜(TEM)和ZATESIZER测定仪对分离纯化过程中所得3个级分进行了分析表征和电荷特性的研究;采用烧杯实验法对3个级分处理实际和模拟水样的混凝效果进行了对比性研究.Al- Ferron逐时络合比色法和TEM结果表明,在层析法分离中级分随着洗脱时间延长按分子的大小依次洗脱下来,因此截取中间组分即可得到含量95 %左右的纳米Al₁₃形态;电荷特性和混凝效果研究结果表明,第3个级分其他两者具有更好的除浊、除腐殖酸和脱色效果,并且具有更强的电中和能力,因此Al₁₃形态是一种具有较高正电荷和较高的水解稳定性以及宽的pH适用范围,在给水和废水处理中是一种较为有效的Al形态.     

复合型生物絮凝剂成分分析及其絮凝机理的研究

蒽酮反应、考马斯亮蓝、紫外扫描等测定结果表明,絮凝剂CBF的主要成分为多糖类物质．红外光谱扫描分析CBF中含有羧基,分别以-COO^-和COOH的形式存在．用凝胶色谱柱测其相对分子量为10^5-10^6．Zeta（ζ）电位测定及氢键和离子键检验结果表明,CBF与高岭土等无机颗粒之间的作用力为离子键,絮凝过程中存在架桥作用．利用原子力显微镜观察其絮凝形态发现絮体结构密实,有利于絮体沉降．其絮凝机理为絮凝剂和高岭土以离子键的形式结合,之后通过架桥作用絮凝沉淀．     

Separating method and dynamic processes of Nano-Al13

In order to investigate the characteristics of pure Nano-Al₁₃, Nano-Al₁₃ was separated and purified from a series of poly-aluminum chloride (PAC) solutions which had the same Al₁₃ percentage but different total Al concentrations, by using column chromatography, ethanol-acetone resolving and SO²⁻ ₄/Ba²⁺ displacement. The Al₁₃ species yield was characterized by Al-ferron timed complexation spectrophotometry and ²⁷Al-NMR (nuclear magnetic resonance). The coagulation efficiency of Nano-Al₁₃, PAC and AlCl₃ in synthetic water was also investigated by Jar tests. The dynamic process and aggregation state of kaolin suspensions coagulating with Nano-Al₁₃, PAC and AlCl₃ were similarly investigated using a photometric dispersion analyzer 2000 (PDA2000). The experimental results indicated that the ethanol-acetone resolving method was simple and could separate the PAC solution at different concentrations, while column chromatography could separate PAC solutions at low concentrations. The SO₄ ²⁻/Ba²⁺ displacement method could separate PAC solutions at high concentrations. However, extra inorganic cation and anion could be added in the solution during separation. The coagulation efficiency and dynamic experimental results showed that Nano-Al₁₃ with high positive-charged species was effective in removing turbidity and color. The dynamic process results showed that Nano-Al₁₃ also had the best recovery capability after shearing compared with PAC and AlCl₃ because the Nano-Al₁₃ conformation is more effective in charge neutralization. Translated from Acta Scientiae Circumstantiae, 2005, 25(6): 767–772 [译自: 环境科学学报]     

Purification and characterization of Al13 species in coagulant polyaluminum chloride

Nano-Al₁₃ was separated and purified by four methods to investigate its characteristic, and was analyzed by Al-Ferron timed complexation spectrophotometer,²⁷ Al-NMR (nuclear magnetic resonance), and transmission electron microscopy (TEM). Coagulation efficiency of nano-Al₁₃, polyaluminum chloride (PAC), and AlCl₃ in synthetic water were also investigated by jar test. The dynamic process and aggregation state of kaolin suspensions coagulating with nano-Al₁₃, PAC, and AlCl₃ were also investigated. The experimental results indicated that the efficiency of gel column chromatography method was the highest for separating PAC solution with low Al concentration. Ethanol and acetone method was simple and could separated PAC solution with different Al concentrations, while silicon alkylation white block column chromatography method could separate PAC solution only with low Al concentration. The SO₄²−/Ba²⁺ displacement method could separate PAC solution with high Al concentration, but extra inorganic cation and anion could be introduced into the solution during the separation. The coagulation efficiency and dynamic experimental results showed that nano- Al₁₃ with a high positive-charged species was the main species of electric neutralization in coagulation process, and it could reduce the turbidity and increase the effective particles collision rate efficiently in coagulation process. Its coagulation speed and the particle size of coagulant formed were of greatest value in this study.     

Preferential binding between intracellular organic matters and Al13 polymer to enhance coagulation performance

Coagulation is the best available method for removing intracellular organic matter (IOM), which is released from algae cells and is an important precursor to disinfection by-products in drinking water treatment. To gain insight into the best strategy to optimize IOM removal, the coagulation performance of two Al salts, i.e., aluminum chloride (AlCl₃) and polyaluminum chloride (PACl, containing 81.2% Al₁₃), was investigated to illuminate the effect of Al species distribution on IOM removal. PACl showed better removal efficiency than AlCl₃ with regard to the removal of turbidity and dissolved organic carbon (DOC), owing to the higher charge neutralization effect and greater stability of pre-formed Al₁₃ species. High pressure size exclusion chromatography analysis indicated that the superiority of PACl in DOC removal could be ascribed to the higher binding affinity between Al₁₃ polymer and the low and medium molecular weight (MW) fractions of IOM. The results of differential log-transformed absorbance at 254 and 350?nm indicated more significant formation of complexes between AlCl₃ and IOM, which benefits the removal of tryptophan-like proteins thereafter. Additionally, PACl showed more significant superiority compared to AlCl₃ in the removal of < 5?kDa and hydrophilic fractions, which are widely viewed as the most difficult to remove by coagulation. This study provides insight into the interactions between Al species and IOM, and advances the optimization of coagulation for the removal of IOM in eutrophic water.     

化学沉淀分离-置换法提纯Al13的工艺研究

采用AlCl₃溶液和Na₂CO₃粉末在不同温度下制备了不同浓度的聚合氯化铝(PACl). 以选定的中等浓度、高Al₁₃含量的PACl为原液,研究了Al₁₃与硫酸盐沉淀反应过程中SO₄/Al摩尔比、反应体系起始总铝浓度的影响以及Al₁₃硫酸盐与Ba(NO₃)₂置换反应过程中的Ba/SO₄摩尔比、超声、温度等因素的影响. 实验结果表明,在制备温度为50℃条件下,浓度在0.4～0.6　mol/L范围的PACl含有较高的Al₁₃. 沉淀分离反应的最佳SO₄/Al摩尔比为0.6∶1;生成的 Al₁₃硫酸盐沉淀物为正四面体状晶体. 在Al₁₃硫酸盐与Ba(NO₃)₂溶液置换反应过程中,Ba/SO₄的最佳摩尔比为1∶1,反应温度及超声作用对置换反应的影响较小;提高Ba(NO₃)₂的起始浓度可以得到相应较高浓度的纯化Al₁₃溶液. 所得Al₁₃纯度的统计平均值为92.1％.     

丽江市夏季降水化学组成分析

运用相关分析、趋势分析、海盐示踪法和HYSPLIT模型,对2006-05-23～2006-07-02云南丽江市夏季降水常量离子的化学特征分析表明,降水中离子浓度的大小顺序为SO^2-₄>Ca²⁺>Cl^->NO^-₃>Na⁺>K⁺>Mg²⁺,其中SO^2-₄和Ca²⁺是夏季降水中的高浓度离子,分别占离子总浓度的65.5%和15.6%;13次降水中阴离子总浓度显著高于阳离子总浓度.夏季降水中SO^2-₄∶NO^-₃变化范围为7.2～37.1, 平均值为15.7, 表明SO^2-₄为该区降水酸度的主要贡献者.由于离子在大气中的相互反应和来源的相似性,离子间相关性水平较好,其中SO^2-₄和NO^-₃的相关系数为0.74;离子浓度与同期降水和平均风速表现负相关.研究区夏季降水中NO^-₃、 SO^2-₄、 K⁺、Ca²⁺主要是陆源物质输入,NO^-₃、 SO^2-₄、 K⁺、Ca²⁺、Mg²⁺和Cl^-陆源物质贡献比例依次为100%、 98.8%、 96%、 99.3%、 46.7%和50.3%.人类经济活动导致的一些污染是该区大气环境变化的主要原因;丽江周边工业区的污染物质主要通过局地环流输入,南亚、东南亚和我国东南沿海工业区的污染物质主要随季风环流输入.     

二噁英/呋喃类的PGC柱-高效液相色谱精制法

针对现行二英物质的三氧化二铝柱分离净化技术的缺陷,介绍了目前最新的二英类物质间的单离纯化技术———高效PGC(PorousGraphiticCarbon)柱-液相色谱分离方法的实际应用。通过13C-二英类物质的实际分离条件以及分析流程的研究,二英类的最终纯化技术达到自动化。对实际土壤中二英类物质的分析结果表明:单分离二英类物质组分效果良好,回收率稳定达到99%以上,自动化程度高;溶剂用量少,安全性好;排除了人为干扰,减少了操作过程的失败。