纳米Al13的分离方法及混凝效果动态过程的研究

以相同Al13含量、不同浓度的PAC为原料,利用乙醇-丙酮混合溶剂法、SO4^2-／Ba^2 沉淀置换法以及柱层析法分离提纯纳米Al13形态,同时利用Al-Ferron逐时络合比色法、^27Al-NMR等多种现代分析手段进行分析鉴定,比较其分离效果,并采用烧杯实验法和透光率脉动检测技术对Al13形态以及PAC、AlCl3的絮凝效果及絮凝过程中絮集物形成和增长的变化差异作了对比性研究．实验结果表明,乙醇．丙酮混合溶剂法对Al13分离纯化效果最好,分离所得Al13平均粒径大,聚合程度高．柱层析法受柱体积的影响只对低浓度的PAC有较好的分离效果;SO4^2-／Ba^2 沉淀置换法虽具有较好的分离效果,但分离过程有其他杂质离子的加入,影响到产品品质．混凝效果和动态实验结果表明,Al13形态是在絮凝过程中起电中和作用的主要形态,具有较强的除浊及脱色能力,在混凝过程中当絮体受到剪切力的破坏时Al13形态比PAC和AlCl3具有更强重新絮凝的能力．     

聚合氯化铝中纳米Al13形态的混凝效应

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al13形态,用透光率脉动检测技术并结合絮凝效能和Zeta电位测定结果,对纳米Al13形态以及PAC、AlCl3絮凝过程中絮集物形成和增长的变化差异作了对比性研究.结果表明,混凝剂的不同铝形态分布在混凝过程中起着十分重要的作用.Al13形态是在絮凝过程中起电中和作用的主要形态,可以大大增加颗粒间的有效碰撞率,其凝聚速度和所形成絮集物颗粒大小在实验条件下呈现最大值.而对于PAC,其Alc含量较高,可起到吸附架桥和网捕卷扫作用,所以在低投加量表现出较快的絮体增长速率.     

聚合氯化铝中纳米Al13形态的分离纯化及形态表征

采用超滤法和层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al-Ferron逐时络合比色法、²⁷Al-NMR、TEM和粒度测定仪对分离纯化所得的Al₁₃形态进行了分析和表征.研究结果表明,超滤法分离纯化的效果受超滤膜的孔径及PAC浓度的影响,选择合适孔径的膜和PAC溶液浓度即可以获得高纯度的Al₁₃,在层析法中则随着洗脱时间延长按分子的大小依次洗脱下来,因此截取中间组分即可得到Al₁₃;Al-Ferron逐时络合比色法和²⁷Al-NMR的分析结果表明,采用上述2种方法分离提纯得到的样品中Al₁₃的含量分别可达到90%以上和100%.TEM和粒度测定结果表明,在B=2.5的PAC溶液中,Al₁₃极少以Al₁₂AlO₄(OH)₂₄(H₂O)⁷⁺₁₂的单体形态存在,而是呈两维结构的线性和枝状的聚集体,Al₁₂AlO₄(OH)₂₄(H₂O)⁷⁺₁₂的聚集体尺寸通常在几十至几百nm.     

聚合氯化铝中Al_(13)形态水解稳定性的研究

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al13形态,并采用Al-Ferron逐时络合比色法对比研究了Al13形态、PAC和Al13三种样品水解稳定性。研究结果表明Al13形态无论是对于稀释倍数、介质的pH值和水解时间都具有较高的水解稳定性,是给水和废水处理中的一种较为有效的Al形态。     

A novel method to synthesize polyaluminum chloride with a membrane reactor

Al13 or Alb is usually regarded as the most efficient species of polyaluminum chloride(PAC), the performance flocculant for water treatment. This paper was intended to report a new method to synthesize PAC with high content Alb, by using the membrane reactor. NaOH solutions were managed to permeate slowly through the micropores of ultrafiltration membrane into AlCl3 solutions under the suitable transmembrane pressure(TMP). Meanwhile NaOH drops size was limited to nano-scale, resulting in dramatical reduction of the characteristic diffusion time and great increment of contact interface between the strong base and AI ions in solution to favor the formation of Al(OH)4^-, the precursor of AI,3, so few precipitates and much Alb are produced. When the initial concentration of AlCl3/NaOH is 0.40/2.0 (mol/L), MWCO = 10000, TMP = 0.0085 MPa, T= 305 K and B(molar ratio of OH^-/Al^3 ) = 2.25, the quantity of Alb attains about 80%. The results of ^27Al-NMR determination showed that the Al13 content is equal to Alb content. And our PAC product has shown better flocculation effects than the commercial product.     

聚合氯化铝中纳米Al13电荷特性及其混凝效果

采用聚丙烯酰胺凝胶柱层析法分离纯化聚合氯化铝(PAC)中的Al₁₃形态,并采用Al-Ferron逐时络合比色法和ZATESIZER 3000HSA测定仪对分离所得纳米Al₁₃形态以及AlCl₃和PAC进行了分析表征和电荷特性的对比性研究;采用烧杯实验法对3个样品处理实际和模拟水样的混凝效果进行了对比性研究.Al-Ferron逐时络合比色法的结果表明,采用层析法分离可得到含量99%左右的纳米Al₁₃形态;电荷特性和混凝效果研究结果表明纳米Al₁₃形态较其它两者具有更好的除浊、除腐殖酸和脱色效果并且具有更强的电中和能力,因此Al₁₃形态是一种具有较高正电荷和较高的水解稳定性,在给水和废水处理中的一种较为有效的Al形态.     

电化学合成的聚合氯化铝的形态特征

采用电解法合成了聚合氯化铝溶液 ,并采用2 7AlNMR法、透射电镜等方法对其形态特征进行了研究 .2 7AlNMR法表明在电化学制备PAC中主要含有铝单体 ,铝的二聚体及Al13形态 .Al13含量与其溶液的碱化度 (B)有关 .在总铝浓度 (AlT)为 2 .0mol L ,B为 2 .2时Al13含量达到最高 ,占AlT 的 70 .2 % ,并在溶液中较稳定存在 .透射电镜实验结果表明 ,电解制备的PAC的粒度分布均匀 ,无团聚现象产生     

有机溶剂法提纯Al_(13)的方法研究及表征分析

高纯度且水溶性好的Al13固体特别是具有一定构型的Al13晶体的制备,对于研究Al13的结构、生成和转化机理、絮凝应用等具有重要的意义。分别采用乙醇-二氧六环沉淀法、乙醇-四氢呋喃沉淀法、乙醇-甲基异丁基甲酮沉淀法对微量加碱法制备的聚合氯化铝溶液进行了纯化,并采用Al-Ferron逐时络合比色法、27Al-NMR法和电子扫描显微镜(SEM)对所得到的Al13固体进行了分析表征。结果表明乙醇-二氧六环沉淀法操作最简便,得到的Al13固体纯度最高晶型最规则,Alb含量达到93.5%,Al13含量达到94.6%,呈规则的八面体构型。     

化学沉淀分离-置换法提纯Al13的工艺研究

采用A1Cl3溶液和Na2CO3粉末在不同温度下制备了不同浓度的聚合氯化铝(PACl).以选定的中等浓度、高Al13含量的PACl为原液,研究了Al13与硫酸盐沉淀反应过程中SO4/Al摩尔比、反应体系起始总铝浓度的影响以及Al13硫酸盐与Ba(NO3)2置换反应过程中的Ba/SO4摩尔比、超声、温度等因素的影响.实验结果表明,在制备温度为50℃条件下,浓度在0.4～0.6mol/L范围的PACl含有较高的Al13.沉淀分离反应的最佳SO4/Al摩尔比为0.6∶1;生成的Al13硫酸盐沉淀物为正四面体状晶体.在Al13硫酸盐与Ba(NO3)2溶液置换反应过程中,Ba/SO4的最佳摩尔比为1∶1,反应温度及超声作用对置换反应的影响较小;提高Ba(NO3)2的起始浓度可以得到相应较高浓度的纯化Al13溶液.所得Al13纯度的统计平均值为92.1%.     

聚合铝在高温条件下的Al_(30)形态生成

Al30是新发现的有确切结构的由30个Al原子聚合组成的高聚铝,并被认为是一种混凝优势形态,然而有关高Al30含量絮凝剂生产技术参数非常缺乏,为明确有关影响,主要运用27Al NMR手段研究各类聚合铝(polyaluminum chloride,PAC)溶液在高温条件下的转化反应及转化后的形态,结果表明,高温条件下Al13转化生成了Al30,熟化的PAC比不熟化PAC有更高的转化率,高纯Al13的转化过程中发现有Al14,但掺入单体铝后Al14消失,PAC碱化度控制在2.0~2.4之间、Al13聚集体碱化度控制在2.6以下以及商业聚合铝的稀释和熟化处理等有利于Al13向Al30的转化。n(Si)/n(Al)=0.05时有最佳的Al30生成。     

Purification and characterization of Al13 species in coagulant polyaluminum chloride

Nano-Al₁₃ was separated and purified by four methods to investigate its characteristic, and was analyzed by Al-Ferron timed complexation spectrophotometer,²⁷ Al-NMR (nuclear magnetic resonance), and transmission electron microscopy (TEM). Coagulation efficiency of nano-Al₁₃, polyaluminum chloride (PAC), and AlCl₃ in synthetic water were also investigated by jar test. The dynamic process and aggregation state of kaolin suspensions coagulating with nano-Al₁₃, PAC, and AlCl₃ were also investigated. The experimental results indicated that the efficiency of gel column chromatography method was the highest for separating PAC solution with low Al concentration. Ethanol and acetone method was simple and could separated PAC solution with different Al concentrations, while silicon alkylation white block column chromatography method could separate PAC solution only with low Al concentration. The SO₄²−/Ba²⁺ displacement method could separate PAC solution with high Al concentration, but extra inorganic cation and anion could be introduced into the solution during the separation. The coagulation efficiency and dynamic experimental results showed that nano- Al₁₃ with a high positive-charged species was the main species of electric neutralization in coagulation process, and it could reduce the turbidity and increase the effective particles collision rate efficiently in coagulation process. Its coagulation speed and the particle size of coagulant formed were of greatest value in this study.     

Natural organic matter(NOM) removal from surface water by coagulation

IntroductionNaturalorganicmatter(NOM)inriversandlakesisacomplexmixtureofmoleculeswithvaryingmolecularweightandchemicalnatureandoriginatesfromavarietyofsources(degradationofterrestrialandaquaticorganisms,biologicalactivityinthewaterbody,humaninputsetc.).NO…     

Separating method and dynamic processes of Nano-Al13

In order to investigate the characteristics of pure Nano-Al₁₃, Nano-Al₁₃ was separated and purified from a series of poly-aluminum chloride (PAC) solutions which had the same Al₁₃ percentage but different total Al concentrations, by using column chromatography, ethanol-acetone resolving and SO²⁻ ₄/Ba²⁺ displacement. The Al₁₃ species yield was characterized by Al-ferron timed complexation spectrophotometry and ²⁷Al-NMR (nuclear magnetic resonance). The coagulation efficiency of Nano-Al₁₃, PAC and AlCl₃ in synthetic water was also investigated by Jar tests. The dynamic process and aggregation state of kaolin suspensions coagulating with Nano-Al₁₃, PAC and AlCl₃ were similarly investigated using a photometric dispersion analyzer 2000 (PDA2000). The experimental results indicated that the ethanol-acetone resolving method was simple and could separate the PAC solution at different concentrations, while column chromatography could separate PAC solutions at low concentrations. The SO₄ ²⁻/Ba²⁺ displacement method could separate PAC solutions at high concentrations. However, extra inorganic cation and anion could be added in the solution during separation. The coagulation efficiency and dynamic experimental results showed that Nano-Al₁₃ with high positive-charged species was effective in removing turbidity and color. The dynamic process results showed that Nano-Al₁₃ also had the best recovery capability after shearing compared with PAC and AlCl₃ because the Nano-Al₁₃ conformation is more effective in charge neutralization. Translated from Acta Scientiae Circumstantiae, 2005, 25(6): 767–772 [译自: 环境科学学报]     

聚合氯化铝与有机高分子复合絮凝剂的形态分布研究——AlFerron和~(27)AlNMR相结合

主要研究了Ａｌ－Ｆｅｒｒｏｎ逐时络合比色法和＾２７Ａｌ－ＮＭＲ法应用于聚合铝与有机高分子复合絮凝剂形态分布的测定，结果表明，两种方法分别测定的Ａｌｂ和Ａｌ１３的结果具有一定的相关性；聚合铝与有机高分子复合后其形态分布发生了一定的变化，Ａｌｂ（或Ａｌ１３）的含量有所降低，但仍是优势形态，Ａｌａ（或Ａｌ单）的含量基本保持不变。     

Hydrolyzed AI（Ⅲ） clusters： Speciation stability of nano-All3

Pure nano-Al13 and aggregates at various concentrations were prepared to examine the particle size e ect of coagulation with inorganic polymer flocculant. The property and stability of various species formed were characterized using Infrared, 27Al-NMR, photo correlation spectroscopy (PCS), and Ferron assay. Results showed that concentration and temperature exhibited di erent roles on the stability of Al13. The quantity of Alb species analyzed by ferron assay in the initial aging period corresponded well with that of Al13, which has been confirmed in a dimension range of 1–2 nm by PCS. Al13 solutions at high concentrations (0.5–2.11 mol/L) were observed to undergo further aggregation with aging. The aggregates with a wide particle size distribution would contribute to the disappeared/decreased Al13 basis on the 27Al-NMR spectrum, whereas a part of Al13 would still remain as Alb. At low concentrations, Al13 solution was quite stable at normal temperature, but lost its stability quickly when heating to 90°C.