TiO2/beads as a photocatalyst for the degradation of X3B azo dye

The feasibility of photocatalytic degradation of X3B azo dye by TiO2/beads photocatalyst was studied.The effects of parameters such as the amount of TiO2/beads,airflow ,as well as the concentrations of H2O2,Fe^3 ,Mg^2 and Na^ on the photocatalytic degradation of X3B azo dye were also studied.The results showed that 25mg/dm^3 X3B azo dye can be photocatalytically degraded completely by 30 min illumination with a 375W medium pressure mercury lamp.Adding a small amount of H2O2 or Fe^3 ,the efficiencies of photocatalytic degradation of X3B azo dye were increased rapidly.The mechanisms of the reaction and the role of the additives were also investigated.After 120 hours TiO2/beads showed no significant loss of the photocatalytic activity.     

纳米TiO_2光催化降解酸性红B的实验研究

采用偶联剂法在聚丙烯多面球表面负载化纳米TiO2,在高压汞灯照射下,以酸性红B染料为研究对象,采用光催化氧化法进行降解处理;研究了溶液初始浓度、H2O2和Fe3+投加量、pH以及光照强度等因素对酸性红B染料降解效果的影响。     

混晶纳米TiO_2的制备及其光催化降解有毒有机污染物

以无定形TiO2沉淀为前驱体,在水热条件下得到了含板钛矿(121)相混晶纳米TiO2,考察了水热反应的温度和时间等因素对含板钛矿型TiO2光催化活性的影响.采用XRD、TEM对制备的TiO2进行初步表征,并结合光催化(λ≤387 nm)降解有机染料的光活性探针反应.结果表明,水热温度为150℃,时间为24 h时,可制得具有较高光催化活性的纳米TiO2,其纳米尺寸为14.20 nm,板钛矿相含量63.6%,锐钛矿含量为36.4%.光催化实验中跟踪研究了其对染料酸性桃红(sulforhodmineB,SRB)的褪色及2,4-DCP的降解情况,并对降解中间产物H2 O2、.OH进行跟踪测定,实验结果表明板钛矿相混晶TiO2的光催化主要涉及.OH氧化历程,光照射9 h对SRB和2,4-DCP的矿化氧化分别达到89%和78%,循环5次光催化降解SRB实验,催化剂表现出较好的稳定性,催化性能无明显变化.     

流化床光催化氧化处理印染废水中试研究

设计了1种流化床光催化氧化中试处理系统,制备了一种负载型TiO₂光催化剂.以高压汞灯为光源,选用难降解偶氮染料4BS和高分子化学浆料CMC配制的模拟印染废水为处理对象,考察了初始pH值、初始浓度以及光助催化剂H₂O₂浓度、Fe₃₊浓度对光催化降解效果的影响,并对有关的光催化反应动力学规律进行了探讨.结果表明,本工艺系统对配制的印染废水有较好的处理效果,光照74min色度去除率可超过80%,光照150min COD去除率可超过70%,BOD₅/COD可提高至0.4以上.     

H_3PW_(12)O_(40)/TiO_2可见光下光催化降解孔雀石绿的研究

以钛酸四丁酯为原料,采用溶胶-凝胶法制备TiO2光催化剂,然后浸渍法制备出H3PW12O40/TiO2复合型光催化剂,并运用XRD、SEM、FT-IR和DRS对催化剂进行表征和分析.研究了可见光光照下H3PW12O40/TiO2对孔雀石绿降解的光催化活性,考察了浸渍量、催化剂用量、底物浓度、pH值对光催化降解率的影响.实验表明,在pH=5条件下,H3PW12O40/TiO2催化剂用量为0.3g.L-1,浓度为10mg·mL-1的孔雀石绿溶液在2L·min-1曝气、300W可见光下光照4h后光催化降解率为78%,比TiO2光催化活性提高了24%.     

Fe~(3+)掺杂TiO_2薄膜的制备及光催化降解甲醛的研究

采用溶胶-凝胶法制备Fe3+掺杂的TiO2薄膜光催化剂,进行甲醛的光催化实验,考察Fe3+掺杂量、薄膜焙烧温度及溶胶体系pH值对光催化性能的影响。结果表明,Fe3+掺杂量为1.0%,焙烧温度500℃1h,加硝酸溶胶体系pH=4时,Fe3+掺杂TiO2薄膜光催化活性最高。     

空心玻璃微球附载TiO2清除水面漂浮的油层

以空心玻璃微球为载体，采用浸涂法制备出ＴｉＯ２／ｂｅａｄｓ光催化剂．研究了利用ＴｉＯ２／ｂｅａｄｓ光催化剂降解水面漂浮的正十二烷及甲苯的可行性．结果表明，３７５Ｗ中压汞灯照射１２０ｍｉｎ，正十二烷的光催化去除率达９３．５％，光照８０ｍｉｎ时甲苯被完全光催化去除；通入空气有利于正二十烷及甲苯的光催化去除，外加微量的Ｈ２Ｏ２（５．０ｍｍｏｌ／Ｌ）可大大提高光催化去除率，向反应液中加入少量Ｎａ＋对正十二烷及甲苯的光催化去除率无明显的影响．     

Fe(Ⅱ)强化声化学降解偶氮染料酸性红B的研究

采用50kHz超声降解偶氮染料酸性红B(ARB),考察了溶液pH和Fe(Ⅱ)浓度对ARB声化学降解过程的影响.结果表明,酸性条件有利于ARB的脱色过程.超声过程中H₂O₂的浓度随时间线性增加.Fe(Ⅱ)和H₂O₂反应生成·OH,强化了ARB的声化学脱色速率和降解过程.当Fe(Ⅱ)浓度为1.43 mg/L和2.85 mg/L时,ARB的脱色速率(在515 nm处)分别提高了1.17倍和1.75倍.同时,ARB在322 nm和254 nm处的紫外吸收亦明显下降.     

TiO2及负载Fe(Ⅲ)可见光催化H2O2降解扑草净的协同效应

以TiO2P25(TIO-P25)及Fe(NO3)3为前驱物制备TiO2负载Fe3+多相催化剂Fe/TIO-P25,研究Fe/TIO-P25可见光催化H2O2降解扑草净的协同效应.XRD、XPS、EDS及SEM结果表明,Fe元素以Fe2O3形式高度分散于TiO2表面,负载量约1.5%(wt%),未对TIO-P25的粒径及形貌产生明显影响,Fe/TIO-P25的粒径约20~40nm;光催化结果表明,Fe/TIO-P25能可见光催化H2O2降解扑草净,反应30min降解率达100%,远大于TIO-P25的催化活性,负载Fe与TIO-P25之间存在明显的协同效应;通过对反应体系的荧光光谱分析显示,扑草净的降解涉及较单纯羟基自由基(·OH)过程更为复杂的反应机理.     

酸性大红GR的Fe~(2+)促进超声化学降解实验研究

采用超声波降解偶氮染料模拟废水酸性大红GR溶液,考察了反应时间、溶液温度、pH值、Fe2+浓度等因素对降解效果的影响。实验结果表明,该法能有效去除酸性大红GR,低温、酸性有利于酸性大红GR的降解;外加Fe2+和超声过程中产生的H2O2反应生成的·OH强化了酸性大红GR的声化学脱色和降解过程,脱色过程符合一级反应。5mmol/L的Fe2+促进超声反应6h,酸性大红GR脱色率达90.5%,COD去除率为65.2%。     

Photo-degradation of Acid-red 3B dye catalyzed by TiO2 nanotubes

Introduction A s one kind of novel functional m aterial, TiO 2 nanotube has been found potential applications in solar cell (B arbe et al., 1997), sem iconductor device (V inodgopal et al., 1993) and catalyst supports (Idakiev et al., 2005) etc. Since K a…     

Activated carbon supported TiO2-photocatalysis doped with Fe ions for continuous treatment of dye wastewater in a dynamic reactor

Fe-doped TiO2 coated on activated carbon (Fe-TiO2/AC, FTA) composites were prepared by an improved sol-gel method and characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, X-ray di ractometry, inductively coupled plasma mass spectrometry and BET surface area analysis. Obtained FTA composites were applied to the continuous treatment of dye wastewater in a dynamic reactor. The e ects of Fe ion content, catalyst content, UV-lamp power and flowrate of the continuous treatment of dye wastewater on degradation e ciency were analyzed to determine the optimum operating conditions of dye wastewater degradation. Continuous photocatalytic experiments provided interesting results that FTA had a high chemical oxygen demand (COD) removal rate compared with TiO2, Fe doped TiO2 (FT) and TiO2 coated on activated carbon (TA). In particular, when using the FTA catalyst with a Fe ion content of 0.33%, the kinetic content (k = 0.0376) of COD removal was more than the sum of both TA (0.0205) and 0.33% FT (0.0166). FTA showed a high photoactivity because of a synergistic e ect between Fe ions and AC on TiO2, which is higher than the individual e ects of AC or Fe ions on TiO2. Additionally, for the photocatalytic degradation of dye wastewater, the optimum Fe ion content, catalyst content, UV-lamp power and flowrate were 0.33%, 6 g/L, 60 W (two lamps) and 300 mL/hr, respectively. An investigation of catalyst reuse revealed that the 0.33% FTA showed almost no deactivation in photocatalytic degradation of naturally treated wastewater.     

Detection of intermediates in the TiO2-assisted photodegradation of Rhodamine B under visible light irradiation

The photocatalytic degradation of dye Rhodamine B （RhB） in the presence of TiO2 nanostdpe or P25 under visible light irradiation was investigated. The degradation intermediates were identified using Infrared spectra （IR spectra）, ^1H nuclear magnetic resonance （^1HNMR） spectra, and gas chromatography-mass spectroscopy （GC-MS）. The IR and the ^1HNMR results showed that the large conjugated chromophore structure of RhB was efficiently destroyed under visible light irradiation in both the photocatalytic systems （TiO2 nanostfipe or P25 and Rhodamine B systems）. GC-MS results showed that the main identified intermediates were ethanediotic acid, 1,2-benzenedicarboxylic acid, 4-hydroxy benzoic acid and benzoic acid, which were almost the same in the TiO2 nanostdpes and P25 systems. This work provides a good insight into the reaction pathway（s） for the TiO2-assisted photocatalytic degradation of dye pollutants under visible light irradiation.     

g-C3N4-P25/光合细菌复合材料降解偶氮染料废水的机理

采用海藻酸钙将g-C3N4-P25和光合细菌进行共固定,合成了光催化-微生物复合材料,并进行了降解模拟偶氮染料废水的研究.结果表明,光催化-微生物复合材料的染料(活性艳红X-3B)脱色率和COD去除率分别为94%和84.7%,远远大于固定光催化剂与固定光合细菌.利用UV-Vis、FT-IR及GC-MS对反应残留物进行表征,根据结果可推测:由光催化产生的自由基和光合细菌共同破坏X-3B的偶氮结构,生成的苯胺类化合物经过一系列的水解、氧化还原作用生成多种具有苯环结构的化合物,然后自由基破坏苯环结构产生长链烷烃,减少芳香烃化合物的累积对光合细菌活性的影响.光合细菌及时利用光催化生成的长链烷烃,产生分子量较小的物质,最后矿化为CO2和H2O.     

在TiO2催化剂上菲的光催化氧化反应研究

选择TiO₂ 粉末催化剂,在发射光谱为254 nm的15 W紫外灯照射下,反应液中Al3+,Fe3+和H2O₂ 浓度增加能提高菲的降解率;TiO₂ 表面载银量的增加能提高降解速度;TiO₂ 投入量在一定范围内随投入量的增加,光催化降解菲的速度也增加,但当投入量较多时又能降低降解速率;在酸性条件下,菲易被光催化降解;菲的起始反应浓度与反应速度成负一级反应动力学关系。      

TiO2/PPY/Fe3O4的水热法制备及其光催化与磁回收性能

以化学氧化法制备的聚吡咯(PPY)包覆Fe3O4复合材料为磁核,用水热反应法(170℃, pH=7±0.2)在其表面负载了纳米Ti02,制成壳/壳/核结构的磁载二氧化钛光催化剂.并用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)、Zeta电位仪对催化剂的物相组成、形貌、表面性质、磁学性质以及磁核的表面电位进行了表征分析.以初始浓度为25mg/L的苯酚溶液为模拟污染物, 对其进行光催化降解以考察其催化活性;并以自制的磁回收装置考察其磁回收率.结果表明,所制备的Ti02粒径在4~7nm,具有混晶结构,其中锐钛矿占95.2%,金红石占4.8%;PPY对Ti02在磁核表面的负载具有促进作用,TiO2在PPY/Fe3O4表面负载牢固;催化剂TPF(nTiO2:n PPY:nFe3O4 =30:2.1:1)具有良好的壳/壳/核结构,其磁感应强度为40emu/g,具有超顺磁性;所制备的催化剂光催化降解苯酚符合假一级反应动力学方程,其中纯TiO2、P25、TPF反应速率常数K值分别为0.0279、0.0264、0.0252,TPF循环使用5次后K值为0.020,催化活性略有降低,循环使用平均回收率可达到90.35%. 该法制备的磁载Ti02光催化剂具有优良的催化活性和磁回收性能,具有良好的应用前景.     

Zr/TiO2纳米颗粒的制备及其光催化活性

以钛酸丁酯,乙醇为原料,用固相合成法制备了Zr/TiO2纳米颗粒,用XRD、TEM对其组成、颗粒大小、形貌进行了表征.通过对罗丹明B的降解反应,考察了Zr/TiO2的光催化活性.结果表明,Zr/TiO2为纳米颗粒,平均粒径为12.7 nm左右,且颗粒均匀;掺杂金属离子Zr提高了TiO2光催化效率,掺杂2.0%Zr的催化剂活性最高.Zr/TiO2的光催化反应,首先是反应物在Zr/TiO2表面发生吸附作用,然后进一步发生光催化降解.     

Preparation, characterization, and photocatalytic activities of boron- and cerium-codoped TiO2

Boron- and cerium-codoped TiO2 photocatalysts were synthesized using modified sol-gel reaction process and characterized by X- ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, particle size distribution （PSD）, diffuse reflectance spectra （DRS）, and Brunauer-Emmett-Teller （BET）. The photocatalytic activities were evaluated by monitoring the degradation of dye Acid Red B （ARB）. The results showed that the prepared photocatalysts were mixed oxides mainly consisting of titania, ceria, and boron oxide. The structure of TiO2 could be transformed from amorphous to anatase and then to rutile by increasing calcination temperature; the transformation being accompanied by the growth of particle size without any obvious change in phase structure of CeO2. The XPS of B1.6Ce1.0-TiO2 prepared at 500℃ showed that a few boron atoms were incorporated into titania and ceria lattice, whereas others existed as B2O3. Cerium ions existed in two states, Ce^3＋ and Ce^4＋, and the atomic ratio of Ce^3＋/Ce^4＋ was 1.86. When boron and cerium were doped, the UV-Vis adsorption band wavelength showed an obvious shift toward the visible range （〈526 nm）. As the atomic ratio of Ce/Ti increased to 1.0, the absorbance edge wavelength increased to 481 nm. The absorbance edge wavelength decreased for higher cerium doping levels （Ce/Ti=2.0）. The particles size ranged from 122 to 255 nm with a domain at 168 nm （39.4%）. The degradation of ARB dye indicated that the photocatalytic activities of boron- and cerium-codoped TiO2 were much higher than those of P25 （a standard TiO2 powder）. The activities increased as the boron doping increased, whereas decreased when the Ce/Ti atomic ratio was greater than 0.5. The optimum atomic ratio of B/Ti and Ce/Ti was 1.6 and 0.5, respectively.     

磷钨酸光催化降解甲基橙溶液的研究

以磷钨酸为光催化剂,在紫外灯照射下,对模拟染料废水甲基橙溶液进行光催化降解反应;研究了催化剂加入量、甲基橙初始质量浓度、外加TiO2和氧化剂H2O2、KIO4对甲基橙溶液光催化脱色效果的影响。结果表明:100mL20mg/L甲基橙溶液光催化剂最佳用量80m g;在较低浓度下,甲基橙溶液的光催化降解反应符合一级动力学方程;在特定条件下,(TiO2+H3PW12O40)/UV、(H2O2+H3PW12O40)/UV和(KIO4+H3PW12O40)/UV光催化体系对甲基橙溶液光催化脱色效果优于H3PW12O40/UV光催化体系。     

活性炭负载TiO2催化剂对直接耐酸大红4BS溶液的光催化降解研究

采用溶胶-凝胶法制备了活性炭负载型TiO2催化剂,采用了XRD、BET和SEM对催化剂进行表征。研究了催化剂对直接耐酸大红4BS的紫外光催化降解,比较了活性炭、P25和TiO2／AC对4BS溶液的降解能力,探讨了催化剂煅烧温度和投加量以及染料溶液的初始浓度对光催化降解率的影响,并对催化剂进行了回收再生实验。结果表明,500℃下煅烧的TiO2／AC催化剂比表面积为1147．88m^2／g、TiO2粒径为21．9nm、晶相组成以锐钛矿为主,具有良好的光催化活性和稳定性;90min后2g／L催化剂对150mg／L的4BS溶液紫外光催化降解率达到99．8％。