聚硅硫酸铁絮凝剂的研制及性能研究

以Fe2(SO4)3,H2SO4和Na2SiO3为原料,采用复合共聚生产工艺,制备了聚合硅酸硫酸铁（PFSS）絮凝剂。研究了SiO2含量、Fe^3 /SiO2摩尔比、pH值等因素对硅酸聚合和PFSS稳定性的影响。正交试验结果表明,当SiO2含量为2.0%,Fe^3|/SiO2洋比为1．0时,PFSS具有最佳混凝效果,较宽的pH范围和保持期。与聚合氯化铝（PAC）进行了性能对比试验。结果表明,PFSS比PAC具有更好的去浊、脱色、除油的效果和残留硅、铁量少的特点。     

Properties and coagulation mechanisms of polyferric silicate sulfate with high concentration

Polyferric silicate sulfate （PFSS） with high concentration was prepared using the composite-poly method. The coagulation properties and mechanisms of this new complex were probed using TEM, Fe-Ferron timed complex-colorimetric method, and infrared spectrum method. The results showed that the flocculating effect of polyferric silicate sulfate had an advantage over polyferric sulfate （PFS）, as the optimum coagulation effect could be obtained when the Si/Fe mole ratio was 0.75 in accordance with its macrostructure of PFSS. According to the Fe-Ferron timed complex-colorimetric method, the Si species was mainly Sic, whereas, the Fe species were Fea and Fec in the copolymerization system. The infrared spectra indicated that the structure of these new flocculants was formed by polymers, mainly by olation, which was different from polyferric sulfate, and the vibration of M-OH-M of around 1100 cm^-1, also proved that there existed Fe-OH-Fe and its polymers in some forms.     

Preparation and coagulation efficiency of polyaluminium ferric silicate chloride composite coagulant from wastewater of high-purity graphite production

The aim of the present work was to produce a polyaluminium ferric silicate chloride (PAFSiC) coagulant from acidic and alkaline wastewater of purifying graphite by roasting, and subsequently to evaluate coagulation efficiency of the reagent by treating surface water from the Yellow River as well as municipal wastewater in comparison with the conventional coagulant polyaluminium chloride (PAC). The PAFSiC coagulant was prepared by co-polymerization. The effects of (Al+Fe)/Si molar ratio, OH/(Al+Fe) molar ratio (i.e., value), coagulant dosage and pH value of test suspension on the coagulation behavior of FAFSiC and the stability of the PAFSiC were also examined. Results showed that PAFSiC performed more efficiently than PAC in removing turbidity, chemical oxygen demand (COD), and total phosphate (TP). The PAFSiC with a value of 2.0 and (Al+Fe)/Si ratio of 5 (PAFSiC 2.0/5) showed excellent coagulation effect for both turbidity and COD, while PAFSiC 1.0/5 was the best for TP. The optimum coagulation pH range of PAFSiC 2.0/5 was 5.0–9.0, slightly wider than that of PAC (6.0–8.0). The process can be easily incorporated into high-purity graphite production plants, thereby reducing wastewater pollution and producing a valuable coagulant.     

旋流板塔钠强化石灰石湿式烟气脱硫研究

向石灰石脱硫浆液中添加硫酸钠可提高脱硫率。以旋流板塔为吸收器,测定了钠强化石灰石湿式烟气脱硫过程的脱硫率、pH值等随脱硫反应时间的变化情况,对不同pH值范围内的石灰石溶解速率等进行了分析。在与工业操作温度相近的条件下,测定了不同塔板数时的脱硫率和塔压降,计算了平均单板效率。结果表明,增加塔板数,脱硫率提高,而平均单板效率减小,实验条件下,塔板数由1增加到4,液气比为4L／m^3时脱硫率由25．5％提高到48．6％,而平均单板效率则由25．5％下降到15．3％。得出了平均单板效率与塔板数之间的关系式。     

聚合氯化铝铁的混凝性能

通过聚合氯化铝铁 (PAFC)对不同 p H值原水的混凝实验结果的比较 ,得出原水 p H值不同时 ,发挥最佳混凝效果的 PAFC的 Al/ Fe摩尔比也不同。实验室制聚合氯化铝 (PA C)、聚合氯化铁 (PFC)、PAFC混凝实验结果表明 :p H 6 .5时 ,PAFC(Al/ Fe=5 / 5 ,B=1.5 )的混凝效果最好 ,p H>6 .5时 ,则 PA FC(Al/ Fe=9/ 1,B=2 .0 )的混凝效果最好。     

聚合硫酸铁(PFS)混凝腐殖酸(HA)的过程中典型操作因素的影响研究

针对聚合硫酸铁（PFS）混凝-沉淀去除腐殖酸（HA）水样的过程,通过测定典型操作因素（PFS投加量、原水pH和搅拌方式）下微絮体的zeta电位、上清液的浊度、UV254、pH值及电导率和絮体沉降体积变化,探讨了这些因素对该过程的影响.结果表明：在原水pH=6.00时,PFS混凝HA的主要机制为电中和作用,搅拌方式对PFS的最佳投加范围没有明显的影响,但单一搅拌方式下HA的去除效果更好;在原水pH=8.00时,吸附络合-卷扫絮凝成为主要的混凝机制,复合搅拌方式下PFS的最佳投加量范围大于单一搅拌方式,且前者的HA去除效果更好.整体而言,几种混凝条件下PFS最佳投药量对应的微絮体zeta电位均在-12.00mV左右;原水pH=6.00时PFS混凝-沉淀去除HA的效果比原水pH=8.00时的好,且前者形成的PFS-HA沉淀絮体体积较小,但单一搅拌方式下絮体结构的重组过程并不是影响絮体体积的主要因素.复合搅拌方式中开始阶段的高强度搅拌有助于PFS组分在HA水样中的分散而有利于其电中和作用的发挥,但对PFS的水解过程影响不大.     

新型复合无机高分子混凝剂——聚硅氯化铝(PASC)的净水效果研究

采用共聚方法制备了系列具有不同碱化度（B）和Al/Si摩尔比的聚硅氯化铝（PASC），比较了它们与聚合氯化铝（PAC）的混凝效果及在处理后水中的残留铝含量，研究了B值和pH值对其残留铝含量的影响情况。探讨了PASC的混凝效果和残留铝含量与Al/Si摩尔比之间的关系。结果表明，PASC较PAC具有更好的混凝效果和较低的残留铝含量。对于高浊度水而言，具有适宜Al/Si摩尔比的PASC才具有良好的混凝效果，但对中、低浊度的地表水和含油废水而言，在实验的Al/Si摩尔比范围内，其值越小，混凝效果就越好。PASC在水体中的残留铝含量随着Al/Si摩尔比的降低和B值的升高而下降。PASC和PAC在中性pH条件下具有最低的残留铝含量。     

双碱法烟气脱硫工艺的研究

以旋流板塔为脱硫塔，实验研究了Na2CO3-Ca(OH)2双碱法脱硫工艺，试验了不同液气比L／G、Na^2 浓度、吸收液pH值和进气SO2浓度等主要参数对脱硫率的影响，并考察了Na^ 的损失与操作条件的关系，分析了双碱法脱硫过程的传质反应过程机理以及不同pH值对脱硫率的影响，此外，还讨论了本工艺适宜操作和工业应用前景。     

聚硅酸硫酸铁絮凝剂的制备及应用

制备了不同 Fe/Si含量比的聚硅酸硫酸铁 (PSFS)。比较了不同 Fe/Si的 PSFS的絮凝效果及稳定性 ,实验了 p H值及絮凝剂用量对絮凝效果的影响。研究表明 ,当 p H=3左右 ,Fe/Si含量比为 1∶ 2时制备的PSFS具有较好的絮凝效果。在实验条件下 ,絮凝剂的最佳用量为 8mg/L。     

旋流板塔价廉脱硫剂湿法烟气脱硫工艺

以旋流板塔为脱硫塔，对几种价廉吸收剂的湿法烟气脱硫工艺进行了实验研究，并分析了传质反应机理，试验了不同液气比（L／G）、吸收液pH值和进气SO2浓度等主要参数对脱硫率的影响，并对实验结果进行了分析；结合其传质反应机理，得出了回归方程式，这些吸收剂均来自于工业废料，达到了废治废的效果，价廉脱硫剂的旋流板塔湿法脱硫工艺已用于苏州热电厂35t/h锅炉的烟气脱硫。     

无机-有机复合混凝剂处理夏季引黄水库水的对比研究

合成了具有不同Fe(Al)/聚二甲基二烯丙基氯化铵(PDMDAAC)质量比的无机-有机复合混凝剂PFC-PDMDAAC和PAC-PDMDAAC,并对夏季引黄水库水进行混凝处理.考察了复合比例、投药量、pH值和投加方式对浊度、有机物和叶绿素-a的去除效果;并通过混凝过程中形成絮体的Zeta电位的变化分析了2种混凝剂的混凝机理.结果表明,无机-有机复合混凝剂处理夏季引黄水库水的效果好于2种单独成分的复配使用;复合比例对PFC-PDMDAAC和PAC-PDMDAAC处理夏季引黄水库水的效果影响较大,Fe(Al)/PDMDAAC质量比为4:1,投药量为4mg/L时混凝效果最好;与无机混凝剂相比,复合混凝剂的最佳pH值范围较广,可在5.0~8.0的pH值范围内取得良好的混凝效果;2种混凝剂相比,PAC-PDMDAAC对浊度和叶绿素-a的去除效果较好,而PFC-PDMDAAC对有机物的去除效果更佳.     

Fractionation of residual Al in natural water treatment from reservoir with poly-aluminum-silicate-chloride (PASiC): Effect of OH/Al, Si/Al molar ratios and initial pH

An aluminum fractionation study was conducted for a surface reservoir water treatment to understand the performance of poly-aluminum-silicate-chloride (PASiC) in terms of the residual Al fractions as a function of initial pH. The coagulation performance expressed as turbidity and organic matter removal was established as supporting data. Some extra data were evaluated in terms of the residual Al ratio of the composite PASiC coagulant. The main residual Al sources were the Al fractions derived from the use of PASiC. The turbidity and organic matter removal ability was optimal at initial pH 6.00-7.00, while the concentrations of various residual Al species and the residual Al ratio of PASiC were minimal at an initial pH range of 7.00-8.00. Under the conditions of OH/Al molar ratio = 2.00 and Si/Al molar ratio = 0.05, PASiC had superior coagulation performance and comparatively low residual Al concentrations. The Al fraction in the composite PASiC coagulant seldom remained under such conditions. Experimental data also indicated that the suspended (filterable) Al fraction was the dominant species, and organic-bound or organo-Al complex Al was considered to be the major species of dissolved Al in water treated by PASiC coagulation. Additionally, the dissolved inorganic monomeric Al species dominated the dissolved monomeric Al fraction.     

活性硅酸聚合硫酸铁的研究

以硅酸钠，硫酸和聚合硫酸铁为原料制备活性硅酸合硫酸铁，测定了ＡＳＰＦＳ红外光谱，了Ｆｅ／Ｓｉ摩尔比和水样ＰＨ值等因素对产品和除浊效果的影响当Ｆｅ／Ｓｉ摩尔比为１．５时产品稳定性和除浊效果均较好。     

Enhanced photo--catalytic activity of gold ion and gold modified

ＩｎｔｒｏｄｕｃｔｉｏｎＴｉＯ2ｐｈｏｔｏｃａｔａｌｙｓｉｓｈａｄｂｅｅｎｔｈｅｆｏｃｕｓｏｆｎｕｍｅｒｏｕｓｉｎｖｅｓｔｉｇａｔｉｏｎｓｉｎｒｅｃｅｎｔｙｅａｒｓ,ｐａｒｔｉｃｕｌａｒｌｙｏｗｉｎｇｔｏｉｔｓａｐｐｌｉｃａｔｉｏｎｆｏｒｔｈｅｃｏｍｐｌｅｔｅｍｉｎｅｒａｌｉｚａｔｉｏｎｏｆｕｎｄｅｓｉｒａｂｌｅｏｒｇａｎｉｃｃｏｎｔａｍｉｎａｎｔｓｔｏＣＯ2,Ｈ2Ｏａｎｄｉｎｏｒｇａｎｉｃｃｏｎｓｔｉｔｕｅｎｔ(Ｈｏｆｆｍａｎｎ,1995).Ｈｏｗｅｖｅｒ,ｐｈｏｔｏｏｘｉｄａｔｉｏｎｗａｓａｌｍｏｓｔｎｏ…     

聚合硫酸铁混凝消除水中有机氯的研究

采用聚合硫酸铁(PFS)絮凝剂对水中有机氯农药(OCPs)进行强化混凝处理,并运用响应曲面法(RSM)优化分析了影响OCPs去除率的混凝条件,如pH值、原水浊度、混凝剂投加量和OCPs的初始浓度诸因素.结果表明,各影响因素交互作用显著,最佳混凝条件组合为:pH=5.0、原水浊度=150NTU、PFS投加量为12mg/L、OCPs初始浓度为200ng/L,在此条件下,PFS絮凝剂可有效去除水中OCPs,经模型验证实验得到最佳条件下去除率α-HCH为82.23%、β-HCH为71.15%、γ-HCH为77.28%、δ-HCH为86.27%、 p,p’-DDE为93.78%,与RSM预测值基本相同.结合絮体分形维数和Zeta电位对混凝效果的机理进行了探讨,表明各因素均达到了最佳水平.     

Treatment of manganese wastewater from titanium dioxide plant using complex phosphate

ＩｎｔｒｏｄｕｃｔｉｏｎＵｓｉｎｇｃｏｍｐｌｅｘｐｈｏｓｐｈａｔｅｔｏｔｒｅａｔｍａｎｇａｎｅｓｅｗａｓｔｅｗａｔｅｒｆｒｏｍｔｉｔａｎｉｕｍｄｉｏｘｉｄｅｐｌａｎｔｗａｓｐｒｅｓｅｎｔｅｄｉｎｔｈｉｓｐａｐｅｒ.Ｃｏｍｐａｒｉｎｇｗｉｔｈｏｔｈｅｒ?..     

无机-有机复合絮凝剂的制备及絮凝性能研究

以硫酸铁、硅酸钠、硼砂和聚丙烯酰胺为主要原料,制备了无机-有机复合絮凝剂。采取正交实验设计方法,以COD去除率为指标,研究了Si/Fe摩尔比、Si/B摩尔比、聚丙烯酰胺浓度三种因子对复合絮凝剂处理印染废水效果的影响。结果表明:复合絮凝剂最优制备条件为:Si/Fe为1.5/1、PAM浓度为250mg/L、Si/B为3.5/1;采用最优条件下制备的复合絮凝剂处理印染废水时,最佳投加量(以SiO_2计)为90mg/L,最佳pH值为8.5～9.0,絮凝效果明显好于聚合硅酸硫酸铁。     

印染行业退煮漂废水处理工艺的实验研究

研究"混凝沉淀-Fenton试剂氧化"工艺处理印染行业退煮漂废水,结果表明,在选用的四种混凝剂中,最佳混凝药剂是聚硅酸硫酸铝(PASS),最佳投药量为3 g/L,适宜反应pH值为4~5;用Fenton试剂处理混凝沉淀后的上清液,最佳氧化工艺条件:反应时间为1.5 h、pH为3~5、H2O2投加量为0.2 mol/L、n(H2O2)∶n(Fe2+)值为1.5;经过"混凝沉淀-Fenton试剂氧化"全流程处理后,废水COD cr、BOD5、色度、SS均有较高的处理效果,COD cr去除率达93.55%、BOD5去除率达89.77%、色度去除率达85.71%、SS去除率达95.9%。     

炉内喷钙脱硫的模拟

煤粉炉内喷钙脱硫是应用较为广泛的脱硫技术，运用逾渗理论建立氧化钙脱硫模型，用来模拟煤粉炉喷钙脱硫过程，并对脱硫影响因素：ＳＯ２浓度、温度、Ｃａ／Ｓ比等进行了研究，模拟计算显示了这些因素对脱硫效果的影响，其结果与试验数据相一致。通过该模型计算可以优化脱硫过程，对煤粉炉内喷钙脱硫有重要的指导意义。     

硅藻土强化混凝去除铜绿微囊藻的影响因素研究

以原水中常见的铜绿微囊藻为研究对象,研究了联合硅藻土与聚合氯化铝(PAC)强化混凝去除铜绿微囊藻的效果.考察了PAC和硅藻土的投加量、溶液pH值、天然有机物腐植酸(HA)对藻和浊度去除的影响,并用zeta电位分析方法对混凝剂的静电中和能力进行表征.结果表明:硅藻土具有良好的助凝作用,投加其有助于改善絮体的沉降性能,提高铜绿微囊藻的混凝去除效果,PAC为6mg/L,pH值为7~8,硅藻土投加量为30mg/L时,叶绿素a(Chl-a)去除率可达96%,剩余浊度低于0.9NTU. HA存在会明显抑制铜绿微囊藻的混凝去除,当HA浓度大于1.0mg/L时, Chl-a去除率大幅度下降同时剩余浊度明显上升,硅藻土的投加可以在一定程度上缓解负面作用.