负载TiO2的泡沫镍网光催化降解甲醛的膜厚优化

采用负载TiO2的泡沫镍网光催化降解甲醛,考虑内部和外部质量传递,建立了可预测优化催化剂膜厚的数学模型.分析了TiO2膜厚对光催化降解甲醛的影响,并在模型基础上分析了催化剂层内光的衰减系数和污染物的有效扩散系数对最优催化剂膜厚的影响.结果表明,随着催化剂膜厚的增加,甲醛的降解先增加而后趋于平缓;最优催化剂膜厚受UV光衰减系数的影响较大,受污染物的有效扩散系数的影响较小;由于TiO2催化剂对254nmUV光的强烈吸收,优化的催化剂膜厚只有80nm左右.该模型对实验数据拟合较好.     

Structural and photocatalytic properties of TiO2 films fabricated on silicon substrates by MOCVD method

Silicon(111) and Silicon(100) were employed for fabrication of TiO2 films by metal organic chemical vapor deposition( MOCVD).Titanium(Ⅳ) isopropoxide(Ti[O(C3H7)4]) was used as a precursor. The as-deposited TiO2 films were characterized with FE-SEM, XRD and AFM. The photocatalytic properties were investigated by decomposition of aqueous Orange Ⅱ. And UV-VlS photospectrometer was used for checking the absorption characteristics and photocatalytic degradation activity. The crystalline and structural properties of TiO2 film had crucial influences on the photodegradation efficiency. For MOCVD in-situ deposited films on Si substrates, the photoactivities varied following a shape of “M”: at Iower(350℃ ), middle(500℃ ) and higher(800℃ ) temperature of deposition, relative lower photodegradation activities were observed. At 400% and 700% of deposition, relative higher efficiencies of degradation were obtained, because one predominant crystallite orientation could be obtained as deposition at the temperature of two levels, especially a single anatase crystalline TiO2 film could be obtained at 700℃.     

不同煅烧温度制备的Mn、N掺杂TiO2光催化性能研究

以MnSO4·H2O为锰源,尿素为氮源,采用溶胶-凝胶法制备不同锻烧温度的纯TiO2、Mn-TiO2及Mn-N-TiO2光催化剂,利用X射线衍射、紫外-可见光漫反射光谱及电子自旋共振等技术对样品形貌和结构进行表征,并以罗丹明B的光催化降解为模型反应,考察不同锻烧温度对其光催化活性的影响.结果表明,Mn、N成功掺入TiO2后,有利于提高光催化剂的热稳定性,抑制锐钛矿相向金红石相转化,且光吸收拓展到可见光区域.Mn、N共掺杂样品比单Mn掺杂样品具有更高的光催化活性,400℃下锻烧的Mn-N-TiO2在可见光下对罗丹明B的降解具有最高的光催化活性,光照2h降解率达到100%.高温锻烧Mn-N-TiO2和Mn-TiO2样品在紫外光照射30min后对罗丹明B的降解率在90%以上.     

金属泡沫镍负载纳米TiO2光催化降解甲醛和VOCs

采用溶胶-凝胶法制备了3种掺杂金属离子的纳米TiO₂光催化剂,并将其负载于泡沫镍板上,以室内空气典型污染物甲醛和VOCs为模型反应物,研究了对甲醛和VOCs气体的光催化作用并讨论了La³⁺的最佳掺杂比例以及环境因素对光催化效率的影响.结果表明:该TiO₂催化剂具有良好的锐钛矿型结构;负载掺La 1.5%TiO₂的泡沫镍板90min对甲醛和VOCs的降解率分别为94%和87%,远高于未掺:83%和72%,掺Fe     

Influences of working pressure on properties for TiO2 films deposited by DC pulse magnetron sputtering

TiO2 films were deposited at room temperature by DC pulse magnetron sputtering system.The crystalline structures,morphological features and photocatalytic activity of TiO2 films were systematically investigated by X-ray diffraction (XRD),atomic force microscopy and ultraviolet spectrophotometer,respectively.The results indicated that the working pressure was the key deposition parameters influencing the TiO2 film phase composition at room temperature,which directly affected its photocatalytic activity.With increasing the working pressure,the target self-bias decreases monotonously.Therefore,low temperature TiO2 phase (anatase) could be deposited with high working pressure.The anatase TiO2 films deposited with 1.4 Pa working pressure displayed the highest photocatalytic activity by decomposition of Methyl Orange solution,which the degradation rate reached the maximum (35%) after irradiation by ultraviolet light for 1 h.     

Visible light induced photodegradation of organic pollutants on nitrogen and fluorine co-doped TiO2 photocatalyst

The nitrogen and fluorine co-doped TiO2 polycrystalline powder was synthesized by calcinations of the hydrolysis product of tetrabutyl titanate with ammonium fluoride. Nitrogen and fluorine co-doping causes the absorption edge of TiO2 to shift to a lower energy region.The photocatalytic activity of co-doped TiO2 with anatase phases was found to be 2.4 times higher than that of the commercial TiO2 photocatalyst Degussa P‘25 for phenol decomposition under visible light irradiation. The co-doped TiO2 powders only contain anatase phases even at 1000%. Apparently, ammonium fluoride added retarded phase transformation of the TiO2 powders from anatase to futile.The substitutional fluorine and interstitial nitrogen atoms in co-doped TiO2 polycrystalline powder were responsible for the vis light response and caused the absorption edge of TiO2 to shift to a lower energy region.     

金属掺杂纳米TiO2薄膜的制备和抗菌性能研究

采用sol—gel法在载玻片表面制备了Ce,Cu,i．a,Ag掺杂的锐铁矿相TiO2薄膜,并通过SEM,XRD．FT—IR及UVVIS进行了表征,比较了薄膜的抗菌性能．UV—VIS研究表明,金属掺杂纳米TiO2薄膜在近紫外区吸光度有明显提高。抗菌实验表明掺Ag的TiO2薄膜抗菌效果最佳。     

混晶纳米TiO_2的制备及其光催化降解有毒有机污染物

以无定形TiO2沉淀为前驱体,在水热条件下得到了含板钛矿(121)相混晶纳米TiO2,考察了水热反应的温度和时间等因素对含板钛矿型TiO2光催化活性的影响.采用XRD、TEM对制备的TiO2进行初步表征,并结合光催化(λ≤387 nm)降解有机染料的光活性探针反应.结果表明,水热温度为150℃,时间为24 h时,可制得具有较高光催化活性的纳米TiO2,其纳米尺寸为14.20 nm,板钛矿相含量63.6%,锐钛矿含量为36.4%.光催化实验中跟踪研究了其对染料酸性桃红(sulforhodmineB,SRB)的褪色及2,4-DCP的降解情况,并对降解中间产物H2 O2、.OH进行跟踪测定,实验结果表明板钛矿相混晶TiO2的光催化主要涉及.OH氧化历程,光照射9 h对SRB和2,4-DCP的矿化氧化分别达到89%和78%,循环5次光催化降解SRB实验,催化剂表现出较好的稳定性,催化性能无明显变化.     

混晶纳米TiO_2薄膜光催化降解亚甲基蓝

以钛酸四丁酯为原料采用浸渍提拉法在普通瓷片表面制备TiO2混晶薄膜,用XRD对薄膜进行表征,选用亚甲基蓝催化降解考察TiO2混晶薄膜的催化能力,探讨了紫外光光照强度、亚甲基蓝初始浓度和pH对光催化降解的影响。结果表明:600℃煅烧4h可制备金红石为13.2%的混晶薄膜,平均粒径为22nm;初始浓度在0.313～0.937mg/L,催化反应符合一级动力学方程,半衰期随初始浓度的增加而减小;在光照强度为40W和pH为13时降解率为45.6%,并可多次重复使用。     

邻-氯酚在TiO_2膜上光催化降解及反应动力学特征

以钛酸四丁酯为原料采用Sol Gel法制备了玻璃负载TiO2 膜光催化剂 ,应用XRD表征了不同实验条件下薄膜中TiO2 的晶相结构和粒度。分析了不同层数TiO2 膜的光催化活性和溶液 pH值对邻 氯酚 (2 CP)的影响。结果表明 :处理温度为 50 0℃时不同厚度薄膜中TiO2 均为锐钛矿晶型 ,粒径 8～ 33nm ,5层涂膜光催化活性最高。在高 pH值和低pH值区域 2 CP ,在TiO2 膜上的光催化降解速率较大。 2 CP初始浓度 (C0 )与反应速率 (r0 )的关系符合Langmuir Hinshelwood方程 ,当C0 ≤ 0 .6mmol·L- 1 时 ,降解反应可用一级动力学模式来描述。     

二氧化钛膜光催化降解水中壬基酚的研究

用溶胶-凝胶法于500℃制备了不同层数的锐钛矿纳米二氧化钛（TiO2）薄膜。利用TiO2薄膜作催化剂,研究了水中壬基酚（NP）的紫外光降解特性。考察了镀膜层数、pH值、初始浓度、光照距离和光照时间与降解率的关系。结果表明,镀3层膜,pH值为5．0～6．0,光照距离为9cm,光照时间为60min的条件下,ρ（NP）初始为100μg/L时降解率可达80％以上。     

镍掺杂二氧化钛光催化剂的制备与光催化性能研究

利用溶胶-凝胶法制备了镍掺杂的二氧化钛,采用紫外可见分光光度计、傅里叶红外分光光度计、X衍射仪(XRD)、扫描电镜(SEM)等测试手段对结果进行了表征。表征结果表明在550℃下煅烧的产物主要是锐钛型二氧化钛,镍的掺杂使得二氧化钛的紫外可见反射光谱明显红移,且镍掺杂二氧化钛的粒度减小,团聚程度下降。以活性艳蓝KN-R为模型降解目标物,通过比较镍掺杂二氧化钛、纯二氧化钛以及标准P25二氧化钛的光催化性能发现镍掺杂二氧化钛的光催化活性最好。当钛酸正丁酯/乙醇比为1:25;钛酸正丁酯/冰乙酸比为1:1;钛酸正丁酯/硝酸镍比为1 000:3;煅烧温度为550℃,煅烧时间为2 h时,镍掺杂二氧化钛的光催化效率最高,达到73.3%。     

V~(5+)/TiO_2-SiO_2-GF复合光催化剂制备及降解甲醛的研究

采用溶胶-凝胶法制备了纯TiO2、TiO2-SiO2、V5+/TiO2-SiO2光催化剂,并分别负载于玻璃纤维布上,利用X射线衍射(XRD)和比表面及孔隙度(BET)分析技术对样品进行了表征。以甲醛的降解率来评价复合光催化剂的光催化活性。结果表明:玻璃纤维布预处理方式、TiO2与SiO2的复合配比、V的掺杂量、煅烧温度对纳米TiO2的光催化活性有影响。V5+/TiO2-SiO2复合光催化剂比表面积为143.74 m2/g,晶粒粒径为16.9 nm。     

上转光剂掺杂新型纳米TiO2催化剂的制备及利用可见光降解反应艳蓝KN-R染料的研究

合成了一种新型含有稀土金属Er的上转光剂,40CdF2·60BaF2·0.8Er2O3,此上转光剂在488 nm可见光的激发下,产生了5个波长均小于387 nm的上转换紫外发射峰.采用超声波分散的方法制备出了上转光剂掺杂的纳米TiO2可见光光催化剂.采用X射线衍射(XRD)及透射电镜(TEM)对催化剂进行了表征.以反应艳蓝KN-R为研究对象,研究了在(三基色灯下发出的)可见光的照射下该可见光光催化剂的催化降解性能,并与未掺杂纳米TiO2粉末的催化剂性能进行了对比.实验结果表明,作为掺杂成分的上转光剂可有效地将可见光转化为紫外光并被纳米TiO2粉末吸收利用,在可见光照射50 h后反应艳蓝KN-R降解率达74.36%,大大高于未掺杂纳米TiO2的降解率(23.10%).     

SO42-改性TiO2催化降解茜素红水溶液

基于SO42-对TiO2超强酸化改性制备了SO42-/TiO2催化剂,以茜素红为目标物试验研究了该催化剂的催化降解性能,并考察了降解条件等因素对脱色率的影响.结果表明,SO42-/TiO2具有较强催化降解性能及一定的光催化活性,降解过程中SO42-流失是催化剂失活的主要原因.在pH=7,催化剂加入量为2.5g/L,起始浓度为140mg/L,太阳光等优化工艺条件下降解效果最好,脱色率达到92%.     

石墨烯/二氧化钛降解亚甲基蓝的研究

以钛酸丁酯和氧化石墨烯为前驱物,通过水热法制备石墨烯/二氧化钛(GR/TiO2)复合光催化剂。采用XRD、TEM和FT-IR等技术手段对GR/TiO2粉体的结构和形貌进行了表征。利用对亚甲基蓝光催化降解,考察了GR/TiO2的光催化降解能力,并研究了H2O2用量和p H等因素对光催化降解速率的影响。结果表明:复合催化剂中,TiO2为锐钛型晶体,粒径为25 nm左右,分散在薄纱状的石墨烯上;复合催化剂通过紫外光下光催化性能有所提高,对可见光产生响应,具有良好的稳定性;加入适量H2O2能提高反应速率,碱性条件下,对亚甲基蓝的降解效率更高。     

纳米掺氮TiO_2可见光降解环境内分泌干扰物BPA研究

用水湿法得到掺氮TiO2前体,热处理后得到掺氮TiO2粉体,用XRD和UV-Vis吸收光谱等手段对制备的掺氮TiO2进行了表征,并研究了N-TiO2可见光光催化降解环境内分泌干扰物双酚A。结果表明掺氮TiO2在400℃下煅烧1h,所得粉体是锐钛矿相结构,粒径约12nm,与纯TiO2相比,吸收边明显红移。催化剂掺氮TiO2具有可见光催化活性,且明显高于纯TiO2。在双酚A初始浓度为40mg/L,催化剂掺氮TiO2的煅烧温度为400℃,投加量为0.6g/L,pH=5的条件下的降解效果最好达48.91%。     

Degradation of dyestuff wastewater using visible light in the presence of a novel nano TiO2 catalyst doped with upconversion luminescence agent

IntroductionEvery year ,the dyeing processes and dye productionbring large amounts of wastewaters containing highconcentration poisonous organic compounds ( Neppolian,2002 ; An, 2002) . If not being treated properly andbetimes , the wastewaters will serio…     

TiO_2/beads as a photocatalyst for the degradation of X_(3B) azo dye

ＩｎｔｒｏｄｕｃｔｉｏｎＥｎｖｉｒｏｎｍｅｎｔａｌｐｒｏｔｅｃｔｉｏｎｅｘｐｅｒｔｓｉｎｍａｎｙｃｏｕｎｔｒｉｅｓｐａｙｈｉｇｈａｔｔｅｎｔｉｏｎｔｏｔｈｅｄｉｓｐｏｓａｌｏｆｔｈｅｗａｓｔｅｗａｔｅｒｗｉｔｈｄｙｅｏｒｗｉｔｈｄｅｅｐｃｈｒｏｍａ.Ｔｈｏｕｇｈａｔｐｒｅｓｅｎｔｂｉｏｄｅｇｒａｄａｔｉｏｎｉｓｕｓｅｄｉｎｔｈｅｄｉｓｐｏｓａｌｏｆｔｈｅｗａｓｔｅｗａｔｅｒ,ｔｈｅｃｏｎｃｅｎｔｒａｔｉｏｎａｎｄｃｈｒｏｍａｉｎｔｈｅｄｉｓｐｏｓｅｄｗａｔｅｒａｒｅｓｔｉｌｌｖｅｒｙｈｉｇｈａｎｄ…     

Photocatalytic degradation of methyl orange over ITO/CdS/ZnO interface composite films

ITO/CdS/ZnO interface composite films were successfully prepared by subsequent electrodeposition of CdS and ZnO onto indium tin oxide (ITO) glass substrates. The obtained ITO/CdS/ZnO composite films were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-Vis spectroscopy. The photocatalytic activity of ITO/CdS/ZnO composite films were investigated using methyl orange (MO) as a model organic compound under UV light irradiation. The influence of operating parameters on MO degradation including initial concentration of MO, pH value of solution, and inorganic anion species over the composite films were examined. A blue shift of absorption threshold was observed for the ITO/CdS/ZnO film in comparison with ITO/ZnO film. ITO/CdS/ZnO composite films prepared under specific conditions showed a higher photocatalytic activity than that of ITO/ZnO films. It was also found that the photocatalytic degradation of MO on the composite filing followed pseudo-first order kinetics.