Contamination and source assessment of metals,polychlorinated biphenyls,and polycyclic aromatic hydrocarbons in urban soils from Addis Ababa,Ethiopia

Urban areas in developing countries are facing vast environmental problems as a result of rapid urbanization and industrialization. Of major concern is the contamination of soils which are increasingly becoming sinks for environmental pollutants. However, to date only little is known about the pollution in the megalopolises of developing countries. The aim of this study was to assess the contamination and potential sources of metals, polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) in the urban environment of Addis Ababa, the capital of Ethiopia. The investigation revealed the presence of most of the analyzed pollutants in soil and sediment samples with total concentrations (dry wt) of PAHs ranging from 186 to 3150?µg?kg^?1, PCBs from 0.4 to 19?µg?kg^?1, Cu from 14 to 173?mg?kg^?1, Zn from 36 to 440?mg?kg^?1, Pb from 9 to 700?mg?kg^?1, and Ni from 16 to 72?mg?kg^?1. In addition, polyaromatic sulfur heterocycles, typical for oil and petrol residues, were detected in several soil samples. Source identification approaches revealed that Pb, Zn, and Cu are most likely derived from pyrolytic sources, with elevated values in samples related to waste combustion and traffic emissions. Ni is most probably of geogenic origin. For PCBs it is indicated that they are derived from a single source. However, correlations with technical PCB mixtures were inconsistent. PAHs originate from the combustion of biomass, vehicular exhausts, and petrogenic sources.     

A novel extraction method for analysing available sulfamethoxazole in soil

A novel extraction method was established to determine the water-extractable (available) content of sulfamethoxazole (SMX) in soil. The SMX imprinted polymers (MIPs) were synthesised and the performance was evaluated by Fourier transform infrared spectroscopy, scanning electron microscopy and binding experiments. Results showed that the MIPs exhibited good selectivity for SMX, so the MIPs were applied as a sorbent. SMX in soil was extracted by water, sorbed from the extract to MIPs and analysed with a high performance liquid chromatography (HPLC) after its desorption from MIPs. Meanwhile, the classic organic solvent extraction was employed to measure the total SMX content in soil. Results showed that when SMX level in spiked soils varying from 1.0–500?μg?kg^?1, the observed recoveries of available SMX contents ranged from 63.27?±?3.11% to 82.11?±?2.77% (n?=?3), while the total SMX varied between 89.59?±?1.65% and 97.64?±?3.92% (n?=?3). The detection limit of the developed method for SMX in soils was 0.05?μg?kg^?1. Available SMX contents in five field soil samples ranged from 0.13 to 4.14?μg?kg^?1, which were only 0.35–25.40% of the respective total SMX contents. Results from this study manifest the importance of the extents of SMX immobilisation with different soils for assessing SMX's ecological and human health risks.     

Removal of Eu3+, Ce3+, Sr2+, and Cs+ ions from radioactive waste solutions by modified activated carbon prepared from coconut shells

As a biomass agricultural waste material, coconut shells were used for the preparation of high-quality modified activated carbon. Chemical modification of the surface of the prepared activated carbon is done by oxidation using H₂O₂ and HNO₃, respectively. The surface area and pore volume of the coconut shells activated carbon are increased by the chemical modification, and followingly the removal of the metals is improved. The structural morphology and composition of the modified activated carbon coconut shells (MACCS) were evaluated by Fourier transform infrared (FTIR) spectra, thermogravimetric analysis–differential thermal analysis (TGA-DTA), scanning electron microscope (SEM), X-ray diffraction (XRD), surface area analysis (SAA), X-ray fluorescence (XRF), and carbon, hydrogen, nitrogen, and sulfur (CHNS) elemental analysis. The prepared MACCS has reasonably good chemical stability. The influence of solution pH, contact time, adsorbent dosage, adsorption temperature, initial metal concentrations, and interfering ions on the adsorption performance of the investigated ions onto the prepared sorbent was examined by a batch method. The selectivity sequence for sorption of Eu³⁺, Ce³⁺, Sr²⁺, and Cs⁺ ions on MACCS was found to be Eu^3+?>?Ce^3+?>?Sr^2+?>?Cs⁺. The saturation capacities of MACCS for the studied metal ions were found to be 136.84, 85.55, 69.85, and 60.00?mg?g^?1 for Eu³⁺, Ce³⁺, Sr²⁺, and Cs⁺ ions, respectively. The thermodynamic parameters, ΔH°, ΔS°, and ΔG° were also evaluated.     

Speciation of mercury in South African coals

Total mercury (Hg_TOT) concentrations were determined by inductively coupled plasma mass spectrometry (ICP MS) for South African Highveld coals. The distribution of Hg in coals was investigated using a four-stage sequential leaching protocol and isotope dilution/gas chromatography coupled to ICP MS (ID-GC-ICP MS). The results show that Hg_TOT ranged from 144 to 303?µg?kg^?1 with a mean of 199?±?26?µg?kg^?1, while Hg_TOT leached from coals using different solvents ranged between 103 and 310?µg?kg^?1 (mean: 218?±?60?µg?kg^?1). Hg leaching rates of 53–78% were achieved in crushed coals. Hg⁰, Hg²⁺, and CH₃Hg⁺ were identified in all coals. CH₃Hg⁺ in studied coals ranged between 0.1 and 0.4 (mean: 0.2) µg?kg^?1. GC ICP MS chromatograms also showed unknown Hg peaks which were identified as other organomercury species such as ethylmercury. Modes of occurrence of Hg in coals were variable with the organic-bound (37–40%) and the sulfide-bound (37–39%) being the dominant mercury forms. Increasing the HCl concentration in the used protocol increased the amount of Hg leached (16%) during this step.     

Abstracts to forthcoming papers

Food is the major source of metal exposure for the nonsmoking general population. Food samples of plant and animal origin from Ismailia, Egypt, were analyzed for the content of cadmium (Cd), lead (Pb), chromium (Cr), zinc (Zn), and copper (Cu) using AAS. The Cr, Zn, and Cu concentrations were in the range of 1.7–249?µg?kg^?1 wet weight (ww), 2–66?mg?kg^?1?ww, and 0.5–3.46?mg?kg^?1?ww, respectively. The mean daily intake of Cr, Zn, and Cu was 28.9?µg day^?1, 8.55?mg day^?1, and 1.7?mg day^?1, respectively. The intake estimates are within the range of the recommended intake established internationally. Concentrations of Cd and Pb were in the range of 10–321?µg?kg^?1?ww and 31–1200?µg?kg^?1?ww, respectively. The weekly dietary intake for Cd and Pb (4.02 and 20.4?µg?kg^?1 b.w, respectively) is lower than the FAO/WHO PTWI. Bread is the foodstuff that provided the highest rate of Pb and Cd (62 and 46% of the daily intake) to adults in Ismailia city.     

Quantitative analysis and sorption of cadmium in environmental samples with a functionalized synthetic polymer

Quantitative analysis of cadmium in environmental samples was achieved with a polymeric sorbent synthesized by copolymerization of N,N-dimethylacrylamide and allyl glycidyl ether/iminodiacetic acid as chelating monomers with N,N′-methylenebisacrylamide as cross-linker. The polymer was characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, elemental analysis, and scanning electron microscopy. The sorption capacity of the functionalized sorbent was 70 mg g^?1. The equilibrium sorption data of Cd(II) on polymeric sorbent were analyzed using Langmuir, Freundlich, Temkin, and Redlich–Peterson models. Based on equilibrium adsorption data, the constants at pH 4.2 and 20 °C were determined for the first three as 0.33 (L mg^?1), 17.5 (mg g^?1) (L mg^?1)^1/n, and 12.9 (J mol^?1). Recovery of 94% of the metal ion was obtained with 0.5 mol L^?1 nitric acid as an eluting agent.     

Toxic effects of dietary of Al3+ ions in tilapias (Oreochromis niloticus) and protective effect of Zn2+ ion

The lethal effects of aluminum ion (Al³⁺) in tilapia (Oreochromis niloticus) raised in concrete tanks were investigated. Tilapias were fed daily with commercial feed enriched with known concentrations of Al³⁺ and analyzed by differential pulse anodic stripping voltammetry (DPASV). The concentrations of Al³⁺ in feces, water, muscle tissue, viscera, and heads were determined every 3 months for a period of 365 days. The Tilapia head was the most affected tissue by Al³⁺. In general, Al³⁺ bioaccumulation reached the lethal dose (LD₅₀) after 335 days of experiment as follows: 34.9?mg?kg^?1 (muscle tissue), 88.2?mg?kg^?1 (viscera), and 126.9?mg?kg^?1 (head without gills). After determining Cu²⁺, Zn²⁺, and Ca²⁺ by absorption spectrometry, a decrease in the Ca²⁺ concentration was noted in the head during the experimental period. These observations were associated with the occurrence of a decalcification in the bone tissue in the presence of Al³⁺. In contrast, it was found that Zn²⁺ ions may act as a protective agent against Al³⁺-induced contamination.     

Determination of metals in printed wiring boards of waste mobile phones

Metal contents of waste mobile phones represent a major environmental risk, especially considering the adoption of inappropriate management options in developing countries including open burning and disposal into surface water bodies. In this study the metal contents of mobile phone printed wiring board (PWB) samples were assessed. Sixty-two waste mobile phones of 15 brands were collected, dismantled, and their PWB samples were analyzed for Cu, Pb, Ag and Cd. The metal concentrations in the samples varied widely between and within brands. Among these metals, Cu and Pb were found to be at very high concentrations. The range (mean?±?SD) of Cu and Pb concentrations were 94.1–532?g?kg^?1 (250?±?92.3?g?kg^?1) and 7.0–46.2?g?kg^?1 (20.1?±?8.4?g?kg^?1), respectively. All Cu and Pb concentrations exceeded toxicity threshold limit concentration (TTLC) regulatory limits used in characterizing wastes as hazardous in the state of California, USA. The mean Cu and Pb concentrations exceeded the corresponding TTLC limits by factors of 100 and 20, respectively. The Ag and Cd concentrations were in the range 59.4–759?mg?kg^?1 (mean 227?±?104?mg?kg^?1) and ND – 15.6?mg?kg^?1 (2.1?±?3.3?mg?kg^?1), respectively.     

Heavy metal pollution in soil and plants at bone char site

This study determined the heavy metal concentration in soil and plants at a bone char site in Umuahia, Nigeria. Soil and plant samples collected in a randomized complete block design (RCBD) were analyzed for zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), and arsenic (As). The concentration of metals in soil and plants in the vicinity of the bone char site are as follows: Zn (172?mg?kg^?1) and Ni (0.62?mg?kg^?1) in soil were highest at site P₃, Pb (2.37?mg?kg^?1) and As (0.08?mg?kg^?1) at site P₁, and Cd (18.30?mg?kg^?1) at site P₂. In plants, the concentrations of Zn (41.17?mg?kg^?1) and Cd (3?mg?kg^?1) were highest in Albizia ferruginea, Ni in Dialium guineense (0.09?mg?kg^?1), while Pb was in D. guineense (0.08?mg?kg^?1) and Spathodea companulata (0.06?mg?kg^?1). The levels of Zn, Cd, Pb, Ni, and As in soil ranged from 11.2 to 172, 2.68 to 18.2, 0.026 to 2.37, 0.33 to 0.62, and 0.02 to 0.08?mg?kg^?1, respectively. In plants, the concentration of Zn, Cd, Pb, and Ni ranged from 2.01 to 41.17, 0.12 to 3, 0.02 to 0.08, and 0.03 to 0.09?mg?kg^?1, respectively. There were significant correlations between Zn and Cd, and Pb and As in soil. The high concentration of Cd in soil might affect soil productivity.     

Elemental composition of bottom-sediments from Pangani river basin,Tanzania: lithogenic and anthropogenic sources

River-bed sediments from the Pangani basin, Tanzania, were characterized for elemental compositions, following contamination risks from rapid expansions of human activities in the area. Samples were collected during two individual seasons and analyzed by high-polarizing beam energy dispersive X-ray fluorescence (EDXRF) for eight major and 14 trace elements. Evaluation of enrichment factors (EFs) was used to investigate the elemental flux and assess the contributions of natural and anthropogenic influences. The abundances of the major elements followed the order Si?>?Al?>?Fe?>?Ca?>?K?>?Ti?>?Mn?>?P, similar to that of the upper earth's crust, and were generally from the weathering of the bed-rock. The high concentrations of typical anthropogenic trace-elements (Cr??1, V??1, Ni??1, Cu??1, La??1) coupled with high EFs (>2) in some locations indicated contamination associated with agricultural and industrial activities. Factor analysis extracted five principal components that contributed to 96.0% of the total observed variance. The results indicated that river-bed sediments of the Pangani basin were influenced to a larger extent by lithogenic sources than anthropogenic impacts.     

Distribution of mercury in the sediments of some freshwater bodies in Ethiopia

Sediment samples were collected from Tinishu Akaki River (TAR), Lake Awassa, and Lake Ziway, Ethiopia for determination of mercury. The air-dried samples were analyzed for mercury with a differential atomic absorption spectrometer after thermal evaporation of bound mercury converting it to its atomic form. Certified reference materials (CRMs) of sediments and soils were used to validate the method. The recovery of mercury from CRMs and sediments was in the range of 95–100%. The limit of detection for the determination of mercury was 50?ng?kg^?1. The concentration of total mercury in the sediments varied from 3.9 to 110?µg?kg^?1 for TAR, 14 to 67?µg?kg^?1 for Lake Awassa, and 17 to 110?µg?kg^?1 for Lake Ziway. It was found that the total mercury concentrations in all samples were below the United States Environmental Protection Agency guideline of 200?µg?kg^?1.     

Persistence of carbaryl and its risk assessment through consumption of treated grapes

The average initial deposits of carbaryl were observed to be 1.4 and 3.1?mg?kg^?1, respectively, following four applications of the insecticide at 4.95 and 9.9?kg active ingredient per hectare. Residues of carbaryl dissipated below its limit of quantification of 50?µg?kg^?1 after 7 and 10 days at single and double the application dosage, respectively. The half-life values (t _1/2) of carbaryl were worked out to be 1.3 and 0.7 days, respectively, at single and double dosages. The acceptable daily intake (ADI) for carbaryl has been fixed at 8?µg?kg^?1 body weight per day. Keeping in view the residues of carbaryl observed one day after the last application, a child of 10?kg and an adult of 60?kg will have an intake of 77 and 154?µg carbaryl after consumption of 100 and 200?g grapes, in comparison to its ADI of 80 and 480?µg; thus, no health risk is to be expected. Therefore, a waiting period of 1 day has been suggested for the safe consumption of carbaryl-treated grapes to avoid any health hazards.     

Mercury pollution in the Sonbhadra district of Uttar Pradesh,India, and its health impacts

The Sonbhadra district in the Singrauli area of Uttar Pradesh, India, has many coal mines and thermal power plants and is a critically polluted area. Many residents of this area reported adverse health conditions which may be linked to metal pollution, especially of mercury investigated here.

In May 2012, samples of water (23), soil (7), blood, hair, and nails from persons showing adverse health conditions selected at random were collected and analyzed for total mercury by atomic absorption spectrometry.

Twenty percent drinking water samples contained mercury from 3 to 26 μg L^?1 (3–26 times the permissible limit). Soil samples had 0.5–10.1 mg kg^?1 Hg.

The average concentrations of mercury in human blood, hair, and nails were found to be 34 μg L^?1, 7.4 mg kg^?1, and 0.8 mg kg^?1, respectively. Mercury concentrations in the blood of these persons were 45 and 28 μg L^?1 on average in the case of men and women. This is much higher than the safe level of 5.8 μg L^?1 set by the United States Environmental Protection Agency (USEPA).

It was concluded that all residents of Sonbhadra sampled could be suffering from mercury toxicity as the area is polluted by Hg released from the coal-fired thermal power plants.     

Long-term stability and risk assessment of copper and cadmium in a smelter-impacted soil treated by four amendments

In an effort to address public concerns of the long-term stability and ecological risk reduction of Cu and Cd in a farmland located at the Guixi, Jiangxi Province, China, containing ～ 800?mg?kg^?1 Cu and 0.8?mg?kg^?1 Cd soil, were treated in situ by attapulgite, apatite, montmorillonite and lime at the rate: 10, 10, 10 and 4?g?kg^?1 soil, respectively. Field experiment consisted of 2?×?3-m plots arranged in a randomised complete block design with each treatment. Soil and plant samples were collected in sixth years post-treatments and analysed for Cu and Cd bioaccessibility, chemical fraction and Cu, Cd concentration in plant tissue. The results indicated that the apatite and lime treatments significantly reduced bioaccessible and exchangeable fractions Cu and Cd in the soil at sixth years post the treatments. Cu and Cd concentration in plant tissue was positively related to the bioaccessibility of Cu and Cd. The treatment used 10?g apatite kg^?1 soil appeared to be most effective for overall risk reduction. The Cu and Cd stabilisation and risk reduction by the apatite treatments were accomplished by the induced transformation of labile Cu and Cu species to relatively insoluble forms. This study illustrated that in situ Cu and Cd stabilisation by apatite would be long-term and ecologically safe, which could safeguard human health and ecosystem from Cu and Cd contamination in mining areas.     

Analysis of heavy metals in ecstasy tablets by electrochemical methods

Trace amounts of heavy metals have been analysed by electrochemical techniques in ecstasy tablets obtained from different police seizures in Spain. Lead, cadmium, copper and zinc were determined by differential-pulse anodic stripping voltammetry at a hanging mercury drop electrode, whereas nickel and cobalt were determined by adsorptive differential-pulse cathodic stripping voltammetry from their dimethylglyoxime complexes, M(DMG)₂. The performance of the procedure was compared with electrothermal atomic absorption spectrometry. The procedure was applied to the determination of these elements in nine ecstasy samples, finding that Zn is the element present in the highest concentration, ranging from 0.3 to 200?mg?kg^?1, Ni, Cu appear below 15?mg?kg^?1 and Pb below 8?mg?kg^?1, while Cd and Co levels were always lower than 0.51?mg?kg^?1.     

Solid phase extraction of trace metals from environmental samples using Amberlite XAD-7 loaded with 2-hydroxy-propiophenone-4-phenyl-3-thiosemicarbazone and determination by inductively coupled plasma–atomic emission spectrometry

A method for the solid phase extraction of trace metals, namely Co, Cu, Pb, Ni and Zn, from environmental and biological samples using column Amberlite XAD-7 loaded with 2-hydroxy-propiophenone-4-phenyl-3-thiosemicarbazone (HPPPTSC) and determination by inductively coupled spectrometry (ICP–AES) has been developed. The reagent has the capacity to form chelate complexes with the metals because of three binding sites in the reagent molecule. The optimum experimental conditions for the quantitative sorption of five metals, pH, effect of flow rate, concentration of eluent, sorption capacity and the effect of diverse ions on the preconcentration of analytes have been investigated. The sorption capacity of the resin has 83, 127, 35, 88 and 85?µmol?g^?1 for Co²⁺, Cu²⁺, Pb²⁺, Ni²⁺ and Zn²⁺, respectively. The preconcentration factors for Co²⁺, Cu²⁺, Pb²⁺, Ni²⁺ and Zn²⁺ were 100, 110, 120, 140 and 150, respectively. The accuracy of the proposed procedure was evaluated by standard reference materials. The achieved results were in good agreement with certified values. The proposed method was applied for the determination of trace metals in river water and plant leaves.     

Effects of salinity on soil bacterial and archaeal community in estuarine wetlands and its implications for carbon sequestration: verification in the Yellow River Delta

Soils from two typical tidal salt marshes with varied salinity in the Yellow River Delta wetland were analysed to determine possible effects of salinity on soil carbon sequestration through changes in soil microbiology. The mean soil respiration (SR) of the salt water–fresh water mixing zone (MZ) was 2.89 times higher than that of the coastal zone (CZ) (4.73 and 1.63?μmol?m^?2?s^?1, respectively, p?Pseudomonas sp. and Limnobacter sp. that might have led to its higher dehydrogenase activity and respiratory rates. Additionally, the CZ possessed more Halobacteria and Thaumarchaeota with the ability to fix CO₂ than the MZ. Significantly lower soil salinity in MZ (4.25?g?kg^?1) was suitable for β-Proteobacteria, but detrimental for Halobacteria compared with CZ (7.09?g?kg^?1, p?相似文献   

Cadmium accumulation characteristics of floricultural plant Cosmos bipinnata*

The artificially high soil cadmium (Cd) concentration screening method was used to screen Cd-hyperaccumulators from floricultural plants. Among the five species of floricultural plants screened, Cosmos bipinnata showed the characteristics of Cd-accumulators. A pot experiment was conducted to further study Cd accumulation characteristics of C. bipinnata. The results showed that the biomass, chlorophyll content, superoxide dismutase activity, peroxidase activity and soluble protein content of C. bipinnata first increased and later decreased with the increase in soil Cd concentration, but the carotenoid content and catalase activity of C. bipinnata reduced. Cd contents in roots, stems, leaves and shoots of C. bipinnata increased with increasing soil Cd concentration. When the soil Cd concentration was 50?mg?kg^?1, the Cd content in shoots was up to 112.62?mg?kg^?1, which was higher than the Cd-hyperaccumulator critical value. The root and shoot bioconcentration factors exceeded 1 in various Cd treatments, but the translocation factors were less than 1. When the soil Cd concentration was 50?mg?kg^?1, the Cd accumulation in shoots achieved the maximum of 224.30?μg plant^?1. Therefore, considering the tolerance and accumulation of Cd, C. bipinnata is a Cd-accumulator that could be used to remediate Cd-contaminated urban soil.     

Lead(II) and cadmium(II) removal from aqueous solution using processed walnut shell: kinetic and equilibrium study

The biosorption potential of processed walnut shell for Pb(II) and Cd(II) ions from aqueous solutions was explored. The effects of pH, contact time, initial ion concentration, and amount of dried adsorbent were studied in batch experiments. The maximum adsorption was achieved within the pH range 4.0–6.0. The equilibrium data were well fitted by the Langmuir isotherm model. The maximum monolayer adsorption capacities were found to be 32?g?kg^?1 and 11.6?g?kg^?1 for Pb(II) and Cd(II) ions, respectively. Kinetic data were best described by the pseudo-second-order model. The structural features of the adsorbent were characterized by Fourier transform infrared spectroscopy, which confirmed the involvement of hydroxyl (–OH), carboxyl (–COO^–), and carbonyl (C=O) groups in metal sorption. This readily available adsorbent is efficient in the uptake of Pb(II) and Cd(II) ions from an aqueous solution and could be used for the treatment of wastewater streams bearing these metal ions.     

Effects of deltamethrin on serum calcium and corpuscles of Stannius of freshwater catfish,Heteropneustes fossilis

Adult male deer mice were exposed every other day for a period of 11 days to either 7,12-dimethylbenzanthracene (DMBA; CAS# 57-97-6) or benzo[b]fluoranthene (BbF; CAS# 205-99-2) (0, 0.3, 1, 3, 10, or 30?mg?kg^?1). Immune endpoints assessed were lymphocyte proliferation, macrophage pinocytosis, and the antibody plaque-forming cell (PFC) response. Cytochrome P450 (CYP450) activity was assessed using ethoxyresorufin-O-deethylase (EROD) and pentoxyresorufin-O-deethylase (PROD). Macrophage pinocytosis was not altered by either compound. Both T- and B-cell proliferations were significantly increased by DMBA at 0.3 or 1?mg?kg^?1 and by BbF at 10 or 30?mg?kg^?1, but decreased by DMBA at 30?mg?kg^?1. Sheep red blood cell (SRBC)-specific-IgM production, as measured by the PFC response, was the most striking adverse immune effect observed and was significantly suppressed compared to control at all treatment concentrations for both compounds. EROD activity was markedly induced by DMBA at 30?mg?kg^?1, while BbF produced induction at 1, 10, or 30?mg?kg^?1. No marked effect on PROD activity was noted following DMBA treatment, but BbF-induced PROD activity at 1, 10, or 30?mg?kg^?1. Unexpectedly, four of six mice in the 30?mg DMBA?kg^?1 group did not survive to the end of the experiment, and one animal died in both the 3 and 10?mg?kg^?1 treatments. The calculated LD₅₀ was 20.8?mg DMBA?kg^?1. The PFC response in deer mice was a more sensitive endpoint than CYP450 activity, suggesting that utilization of CYP450 endpoints in risk assessment without assessment of immune function, specifically antibody production, might possibly underestimate the risk to wild rodents environmentally exposed to polycyclic aromatic hydrocarbons.