A method for quick assessment of CO2 storage capacity in closed and semi-closed saline formations

Saline aquifers of high permeability bounded by overlying/underlying seals may be surrounded laterally by low-permeability zones, possibly caused by natural heterogeneity and/or faulting. Carbon dioxide (CO₂) injection into and storage in such “closed” systems with impervious seals, or “semi-closed” systems with non-ideal (low permeability) seals, is different from that in “open” systems, from which the displaced brine can easily escape laterally. In closed or semi-closed systems, the pressure buildup caused by continuous industrial-scale CO₂ injection may have a limiting effect on CO₂ storage capacity, because geomechanical damage caused by overpressure needs to be avoided. In this research, a simple analytical method was developed for the quick assessment of the CO₂ storage capacity in such closed and semi-closed systems. This quick-assessment method is based on the fact that native brine (of an equivalent volume) displaced by the cumulative injected CO₂ occupies additional pore volume within the storage formation and the seals, provided by pore and brine compressibility in response to pressure buildup. With non-ideal seals, brine may also leak through the seals into overlying/underlying formations. The quick-assessment method calculates these brine displacement contributions in response to an estimated average pressure buildup in the storage reservoir. The CO₂ storage capacity and the transient domain-averaged pressure buildup estimated through the quick-assessment method were compared with the “true” values obtained using detailed numerical simulations of CO₂ and brine transport in a two-dimensional radial system. The good agreement indicates that the proposed method can produce reasonable approximations for storage–formation–seal systems of various geometric and hydrogeological properties.     

Coupled hydromechanical modeling of CO2 sequestration in deep saline aquifers

Sequestration of carbon dioxide (CO₂) in deep saline aquifers has emerged as an option for reducing greenhouse gas emissions to the atmosphere. The large amounts of supercritical CO₂ that need to be injected into deep saline aquifers may cause large fluid pressure increases. The resulting overpressure may promote reactivation of sealed fractures or the creation of new ones in the caprock seal. This could lead to escape routes for CO₂. In order to assess the probability of such an event, we model an axisymmetric horizontal aquifer–caprock system, including hydromechanical coupling. We study the failure mechanisms, using a viscoplastic approach. Simulations illustrate that, depending on boundary conditions, the least favorable moment takes place at the beginning of injection. Initially, fluid pressure rises sharply because of a reduction in permeability due to desaturation. Once CO₂ fills the pores in the vicinity of the injection well and a capillary fringe is fully developed, the less viscous CO₂ displaces the brine and the capillary fringe laterally. The overpressure caused by the permeability reduction within the capillary fringe due to desaturation decreases with distance from the injection well. This results in a drop in fluid pressure buildup with time, which leads to a safer situation. Nevertheless, in the presence of low-permeability boundaries, fluid pressure continues to rise in the whole aquifer. This occurs when the radius of influence of the injection reaches the outer boundary. Thus, caprock integrity might be compromised in the long term.     

Numerical investigation concerning the impact of CO2 geologic storage on regional groundwater flow

Large-scale storage of carbon dioxide in saline aquifers may cause considerable pressure perturbation and brine migration in deep rock formations, which may have a significant influence on the regional groundwater system. With the help of parallel computing techniques, we conducted a comprehensive, large-scale numerical simulation of CO₂ geologic storage that predicts not only CO₂ migration, but also its impact on regional groundwater flow. As a case study, a hypothetical industrial-scale CO₂ injection in Tokyo Bay, which is surrounded by the most heavily industrialized area in Japan, was considered, and the impact of CO₂ injection on near-surface aquifers was investigated, assuming relatively high seal-layer permeability (higher than 10 microdarcy). A regional hydrogeological model with an area of about 60 km × 70 km around Tokyo Bay was discretized into about 10 million gridblocks. To solve the high-resolution model efficiently, we used a parallelized multiphase flow simulator TOUGH2-MP/ECO2N on a world-class high performance supercomputer in Japan, the Earth Simulator. In this simulation, CO₂ was injected into a storage aquifer at about 1 km depth under Tokyo Bay from 10 wells, at a total rate of 10 million tons/year for 100 years. Through the model, we can examine regional groundwater pressure buildup and groundwater migration to the land surface. The results suggest that even if containment of CO₂ plume is ensured, pressure buildup on the order of a few bars can occur in the shallow confined aquifers over extensive regions, including urban inlands.     

A one-dimensional model of vertical gas plume migration through a heterogeneous porous medium

This work is motivated by the growing interest in injecting carbon dioxide into deep geological formations as a means of avoiding its atmospheric emissions and consequent global warming. Ideally, the injected greenhouse gas stays in the injection zone for a geologic time, eventually dissolves in the formation brine and remains trapped by mineralization. However, one of the potential problems associated with the geologic method of sequestration is that naturally present or inadvertently created conduits in the cap rock may result in a gas leakage from primary storage. Even in supercritical state, the carbon dioxide viscosity and density are lower than those of the formation brine. Buoyancy tends to drive the leaked CO₂plume upward. Theoretical and experimental studies of buoyancy-driven supercritical CO₂ flow, including estimation of time scales associated with plume evolution and migration, are critical for developing technology, monitoring policy, and regulations for safe carbon dioxide geologic sequestration.In this study, we obtain simple estimates of vertical plume propagation velocity taking into account the density and viscosity contrast between CO₂ and brine. We describe buoyancy-driven countercurrent flow of two immiscible phases by a Buckley–Leverett type model. The model predicts that a plume of supercritical carbon dioxide in a homogeneous water-saturated porous medium does not migrate upward like a bubble in bulk water. Rather, it spreads upward until it reaches a seal or until it becomes immobile. A simple formula requiring no complex numerical calculations describes the velocity of plume propagation. This solution is a simplification of a more comprehensive theory of countercurrent plume migration [Silin, D., Patzek, T.W., Benson, S.M., 2007. A Model of Buoyancy-driven Two-phase Countercurrent Fluid Flow. Laboratory Report LBNL-62607. Lawrence Berkeley National Laboratory, Berkeley, CA]. In a layered reservoir, the simplified solution predicts a slower plume front propagation relative to a homogeneous formation with the same harmonic mean permeability. In contrast, the model yields much higher plume propagation estimates in a high-permeability conduit like a vertical fracture.     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.     

Basin-scale hydrogeologic impacts of CO2 storage: Capacity and regulatory implications

Industrial-scale injection of CO₂ into saline formations in sedimentary basins will cause large-scale fluid pressurization and migration of native brines, which may affect valuable groundwater resources overlying the deep sequestration aquifers. In this paper, we discuss how such basin-scale hydrogeologic impacts (1) may reduce current storage capacity estimates, and (2) can affect regulation of CO₂ storage projects. Our assessment arises from a hypothetical future carbon sequestration scenario in the Illinois Basin, which involves twenty individual CO₂ storage projects (sites) in a core injection area most suitable for long-term storage. Each project is assumed to inject five million tonnes of CO₂ per year for 50 years. A regional-scale three-dimensional simulation model was developed for the Illinois Basin that captures both the local-scale CO₂–brine flow processes and the large-scale groundwater flow patterns in response to CO₂ storage. The far-field pressure buildup predicted for this selected sequestration scenario support recent studies in that environmental concerns related to near- and far-field pressure buildup may be a limiting factor on CO₂ storage capacity. In other words, estimates of storage capacity, if solely based on the effective pore volume available for safe trapping of CO₂, may have to be revised based on assessments of pressure perturbations and their potential impacts on caprock integrity and groundwater resources. Our results suggest that (1) the area that needs to be characterized in a permitting process may comprise a very large region within the basin if reservoir pressurization is considered, and (2) permits cannot be granted on a single-site basis alone because the near- and far-field hydrogeologic response may be affected by interference between individual storage sites. We also discuss some of the challenges in making reliable predictions of large-scale hydrogeologic impacts related to CO₂ sequestration projects.     

Large-scale impact of CO2 storage in deep saline aquifers: A sensitivity study on pressure response in stratified systems

Large volumes of CO₂ captured from carbon emitters (such as coal-fired power plants) may be stored in deep saline aquifers as a means of mitigating climate change. Storing these additional fluids may cause pressure changes and displacement of native brines, affecting subsurface volumes that can be significantly larger than the CO₂ plume itself. This study aimed at determining the three-dimensional region of influence during/after injection of CO₂ and evaluating the possible implications for shallow groundwater resources, with particular focus on the effects of interlayer communication through low-permeability seals. To address these issues quantitatively, we conducted numerical simulations that provide a basic understanding of the large-scale flow and pressure conditions in response to industrial-scale CO₂ injection into a laterally open saline aquifer. The model domain included an idealized multilayered groundwater system, with a sequence of aquifers and aquitards (sealing units) extending from the deep saline storage formation to the uppermost freshwater aquifer. Both the local CO₂-brine flow around the single injection site and the single-phase water flow (with salinity changes) in the region away from the CO₂ plume were simulated. Our simulation results indicate considerable pressure buildup in the storage formation more than 100 km away from the injection zone, whereas the lateral distance migration of brine is rather small. In the vertical direction, the pressure perturbation from CO₂ storage may reach shallow groundwater resources only if the deep storage formation communicates with the shallow aquifers through sealing units of relatively high permeabilities (higher than 10^?18 m²). Vertical brine migration through a sequence of layers into shallow groundwater bodies is extremely unlikely. Overall, large-scale pressure changes appear to be of more concern to groundwater resources than changes in water quality caused by the migration of displaced saline water.     

Integration of counter-current relative permeability in the simulation of CO2 injection into saline aquifers

Carbon dioxide (CO₂) injection into saline aquifers is one of the promising options to sequester large amounts of CO₂ in geological formations. During as well as after injection of CO₂ into an aquifer, CO₂ migrates towards the top of the formation due to density differences between the formation brine and the injected CO₂. The time scales of CO₂ migration towards the top of an aquifer and the fraction of CO₂ that is trapped as residual gas depends strongly on the driving forces that are acting on the injected CO₂.When CO₂ migrates to the top of an aquifer, brine may be displaced downwards in a counter-current flow setting particularly during the injection period. A majority of the published work on counter-current flow settings have reported significant reductions in the associated relative permeability functions as compared to co-current measurements. However, this phenomenon has not yet been considered in the simulation of CO₂ storage into saline aquifers.In this paper we study the impact of changes in mobility for the two-phase brine/CO₂ system as a result of transitions between co- and counter-current flow settings. We have included this effect in a simulator and studied the impact of the related mobility reduction on the saturation distribution and residual saturation of CO₂ in aquifers over relevant time scales. We demonstrate that the reduction in relative permeability in the vertical direction changes the plume migration pattern and has an impact on the amount of gas that is trapped as a function of time. This is to our best knowledge the first attempt to integrate counter-current relative permeability into the simulation of injection and subsequent migration of CO₂ in aquifers. The results and analysis presented in this paper are directly relevant to all ongoing activities related to the design of large-scale CO₂ storage in saline aquifers.     

Scenario simulations of CO2 injection feasibility, plume migration and storage in a saline aquifer, Scania, Sweden

Deep saline aquifers have large capacity for geological CO₂ storage, but are generally not as well characterized as petroleum reservoirs. We here aim at quantifying effects of uncertain hydraulic parameters and uncertain stratigraphy on CO₂ injectivity and migration, and provide a first feasibility study of pilot-scale CO₂ injection into a multilayered saline aquifer system in southwest Scania, Sweden. Four main scenarios are developed, corresponding to different possible interpretations of available site data. Simulation results show that, on the one hand, stratigraphic uncertainty (presence/absence of a thin mudstone/claystone layer above the target storage formation) leads to large differences in predicted CO₂ storage in the target formation at the end of the test (ranging between 11% and 98% of injected CO₂ remaining), whereas other parameter uncertainty (in formation and cap rock permeabilities) has small impact. On the other hand, the latter has large impact on predicted injectivity, on which stratigraphic uncertainty has small impact. Salt precipitation at the border of the target storage formation affects CO₂ injectivity for all considered scenarios and injection rates. At low injection rates, salt is deposited also within the formation, considerably reducing its availability for CO₂ storage.     

Time-lapse carbon dioxide monitoring with pulsed neutron logging

Elevated levels of CO₂ in the atmosphere have been linked to the rise in land and sea temperature [Climate Change, 2001. In: Houghton, J.T., Ding, Y., Griggs, D.J., Noguer, M., van der Linden, P.J., Xiaosu, D. (Eds.), The Scientific Basis Contribution of Working Group I to the Third Assessment Report of the Intergovernmental Panel on Climate Change (IPCC). Cambridge University Press, UK, p. 944]. To demonstrate geological carbon sequestration as a mitigation technique, a carbon dioxide injection experiment was conducted in East Texas. The target – Frio formation – is a highly porous, permeable and unconsolidated sandstone. The specific interval is the Frio C sand, which originally was saturated with saline formation water. At the injection location, the Frio C sand dips 18° to the south. To monitor the injected CO₂ spreading in the formation, an old well from 1956 drilled into the deeper Yegua formation was selected as the observation well. The injection well was drilled at a distance of 100 ft downdip from the monitoring well. Several borehole measurement methods were available to monitor the CO₂ injection, but the most suitable technology was thought to be the pulsed neutron logging. This logging is used widely in cased hole, and the measured macroscopic thermal absorption cross-section (Σ) is sensitive to CO₂ saturation in high porosity saline water environments. Several log examples are given demonstrating successful the monitoring of the CO₂ plume moving through the two boreholes and the resulting saturation changes.     

Limitations for brine acidification due to SO2 co-injection in geologic carbon sequestration

Co-injection of sulfur dioxide during geologic carbon sequestration can cause enhanced brine acidification. The magnitude and timescale of this acidification will depend, in part, on the reactions that control acid production and on the extent and rate of SO₂ dissolution from the injected CO₂ phase. Here, brine pH changes were predicted for three possible SO₂ reactions: hydrolysis, oxidation, or disproportionation. Also, three different model scenarios were considered, including models that account for diffusion-limited release of SO₂ from the CO₂ phase. In order to predict the most extreme acidification potential, mineral buffering reactions were not modeled. Predictions were compared to the case of CO₂ alone which would cause a brine pH of 4.6 under typical pressure, temperature, and alkalinity conditions in an injection formation. In the unrealistic model scenario of SO₂ phase equilibrium between the CO₂ and brine phases, co-injection of 1% SO₂ is predicted to lead to a pH close to 1 with SO₂ oxidation or disproportionation, and close to 2 with SO₂ hydrolysis. For a scenario in which SO₂ dissolution is diffusion-limited and SO₂ is uniformly distributed in a slowly advecting brine phase, SO₂ oxidation would lead to pH values near 2.5 but not until almost 400 years after injection. In this scenario, SO₂ hydrolysis would lead to pH values only slightly less than those due to CO₂ alone. When SO₂ transport is limited by diffusion in both phases, enhanced brine acidification occurs in a zone extending only 5 m proximal to the CO₂ plume, and the effect is even less if the only possible reaction is SO₂ hydrolysis. In conclusion, the extent to which co-injected SO₂ can impact brine acidity is limited by diffusion-limited dissolution from the CO₂ phase, and may also be limited by the availability of oxidants to produce sulfuric acid.     

Storage of CO2 in saline aquifers: Effects of gravity, viscous, and capillary forces on amount and timing of trapping

CO₂ can be effectively immobilized during CO₂ injection into saline aquifers by residual trapping – also known as capillary trapping – a process resulting from capillary snap-off of isolated CO₂ bubbles. Simulations of CO₂ injection were performed to investigate the interplay of viscous and gravity forces and capillary trapping of CO₂. Results of those simulations show that gas injection processes in which gravitational forces are weak compared to viscous forces (low gravity number N_gv) trap significantly more CO₂ than do flows with strong gravitational forces relative to the viscous forces (high N_gv). The results also indicate that over a wide range of gravity numbers (N_gv), significant fractions of the trapping of CO₂ can occur relatively quickly. The amount of CO₂ that is trapped after injection ceases is demonstrated to correlate with N_gv. For some simulated displacements, effects of capillary pressure and aquifer dip angle on the amount and the rate of trapping are reported. Trapping increases when effects of capillary pressure and aquifer inclination are included in the model. Finally we show that injection schemes such as alternating injection of brine and CO₂ or brine injection after CO₂ injection can also enhance the trapping behavior.     

A solution against well cement degradation under CO2 geological storage environment

Capturing and storing carbon dioxide (CO₂) underground for thousands of years is one way to reduce atmospheric greenhouse gases, often associated with global warming. Leakage through wells is one of the major issues when storing CO₂ in depleted oil or gas reservoirs. CO₂-injection candidates may be new wells, or old wells that are active, closed or abandoned. In all cases, it is critical to ensure that the long-term integrity of the storage wells is not compromised. The loss of well integrity may often be explained by the geochemical alteration of hydrated cement that is used to isolate the annulus across the producing/injection intervals in CO₂-related wells. However, even before any chemical degradation, changes in downhole conditions due to supercritical CO₂ injections can also be responsible for cement debonding from the casing and/or from the formation, leading to rapid CO₂ leakage. A new cement with better CO₂ resistance is compared with conventional cement using experimental procedure and methodology simulating the interaction of set cement with injected, supercritical CO₂ under downhole conditions. Geochemical experimental data and a mechanical modeling approach are presented. The use of adding expanding property to this new cement to avoid microannulus development during the CO₂ injection is discussed.     

Experimental assessment of brine and/or CO2 leakage through well cements at reservoir conditions

Two sets of experiments on typical Class G well cement were carried out in the laboratory to understand better the potential processes involved in well leakage in the presence of CO₂. In the first set, good-quality cement samples of permeability in the order of 0.1 μD (10^?19 m²) were subjected to 90 days of flow through with CO₂-saturated brine at conditions of pressure, temperature and water salinity characteristic of a typical geological sequestration zone. Cement permeability dropped rapidly at the beginning of the experiment and remained almost constant thereafter, most likely mainly as a result of CO₂ exsolution from the saturated brine due to the pressure drop along the flow path which led to multi-phase flow, relative-permeability effects and the observed reduction in permeability. These processes are identical to those which would occur in the field as well if the cement sheath in the wellbore annulus is of good quality. The second set of experiments, carried out also at in situ conditions and using ethane rather than CO₂ to eliminate any possible geochemical effects, assessed the effect of annular spaces between wellbore casing and cement, and of radial cracks in cement on the effective permeability of the casing-cement assemblage. The results show that, if both the cement and the bond are of good quality, the effective permeability of the assemblage is extremely low (in the order of 1 nD, or 10^?21 m²). The presence of an annular gap and/or cracks in the order of 0.01–0.3 mm in aperture leads to a significant increase in effective permeability, which reaches values in the range of 0.1–1 mD (10^?15 m²). The results of both sets of experiments suggest that good cement and good bonding with casing and the surrounding rock will likely constitute a good and reliable barrier to the upward flow of CO₂ and/or CO₂-saturated brine. The presence of mechanical defects such as gaps in bonding between the casing or the formation, or cracks in the cement annulus itself, leads to flow paths with significant effective permeability. This indicates that the external and internal interfaces of cements in wells would most probably constitute the main flow pathways for fluids leakage in wellbores, including both gaseous/supercritical phase CO₂ and CO₂-saturated brine.     

Analytical solution for estimating storage efficiency of geologic sequestration of CO2

During injection of carbon dioxide (CO₂) into deep saline aquifers, the available pore volume of the aquifer may be used inefficiently, thereby decreasing the effective capacity of the repository for CO₂ storage. Storage efficiency is the fraction of the available pore space that is utilized for CO₂ storage, or, in other words, it is the ratio between the volume of stored CO₂ and the maximum available pore volume. In this note, we derive and present simple analytical expressions for estimating CO₂ storage efficiency under the scenario of a constant-rate injection of CO₂ into a confined, homogeneous, isotropic, saline aquifer. The expressions for storage efficiency are derived from models developed previously by other researchers describing the shape of the CO₂-brine interface. The storage efficiency of CO₂ is found to depend on three dimensionless groups, namely: (1) the residual saturation of brine after displacement by CO₂; (2) the ratio of CO₂ mobility to brine mobility; (3) a dimensionless group (which we call a “gravity factor”) that quantifies the importance of CO₂ buoyancy relative to CO₂ injection rate. In the particular case of negligible residual brine saturation and negligible buoyancy effects, the storage efficiency is approximately equal to the ratio of the CO₂ viscosity to the brine viscosity. Storage efficiency decreases as the gravity factor increases, because the buoyancy of the CO₂ causes it to occupy a thin layer at the top of the confined formation, while leaving the lower part of the aquifer under-utilized. Estimates of storage efficiency from our simple analytical expressions are in reasonable agreement with values calculated from simulations performed with more complicated multi-phase-flow simulation software. Therefore, we suggest that the analytical expressions presented herein could be used as a simple and rapid tool to screen the technical or economic feasibility of a proposed CO₂ injection scenario.     

CO2SINK—From site characterisation and risk assessment to monitoring and verification: One year of operational experience with the field laboratory for CO2 storage at Ketzin, Germany

The CO₂SINK pilot project at Ketzin is aimed at a better understanding of geological CO₂ storage operation in a saline aquifer. The reservoir consists of fluvial deposits with average permeability ranging between 50 and 100 mDarcy. The main focus of CO₂SINK is developing and testing of monitoring and verification technologies. All wells, one for injection and two for observation, are equipped with smart casings (sensors behind casing, facing the rocks) containing a Distributed Temperature Sensing (DTS) and electrodes for Electrical Resistivity Tomography (ERT). The in-hole Gas Membrane Sensors (GMS) observed the arrival of tracers and CO₂ with high temporal resolution. Geophysical monitoring includes Moving Source Profiling (MSP), Vertical Seismic Profiling (VSP), crosshole, star and 4-D seismic experiments. Numerical models are benchmarked via the monitoring results indicating a sufficient match between observation and prediction, at least for the arrival of CO₂ at the first observation well. Downhole samples of brine showed changes in the fluid composition and biocenosis. First monitoring results indicate anisotropic flow of CO₂ coinciding with the “on-time” arrival of CO₂ at observation well one (Ktzi 200) and the later arrival at observation well two (Ktzi 202). A risk assessment was performed prior to the start of injection. After one year of operations about 18,000 t of CO₂ were injected safely.     

Re-establishment of the proper injectivity of the CO2-injection well Ktzi 201 in Ketzin, Germany

The onshore CO₂-storage site Ketzin consists of one CO₂-injection well and two observation wells. Hydraulic tests revealed permeabilities between 50 and 100 mD for the sandstone rock units. The designated injection well Ktzi 201 showed similar production permeability. After installation of the CO₂-injection string, an injection test with water yielded a significantly lower injectivity of 0.002 m³/d kPa, while the observation wells showed an injection permeability in the same range as the productivity. Several possible reasons for the severe decline in injectivity are discussed. Acidification of the reservoir interval, injection at high wellhead pressure, controlled mini-fractures and back-production of the well are discussed to remove the plugging material to re-establish the required injectivity of the well. It has been decided to perform a nitrogen lift and analyse the back-produced fluids. Initially during the lift, the back-produced fluids were dark-black. Chemical and XRD analyses proved that the black solids consisted mainly of iron sulphide. Sulphate-reducing bacteria (SRB) were detected in fluid samples with up to 10⁶ cells/ml by fluorescent in situ hybridisation (FISH) indicating that the formation of iron sulphide was caused by bacterial activity. Organic compounds within the drilling mud and other technical fluids were likely left during the well completion process, thus providing the energy source for strong proliferation of bacteria. During the lift, the fraction of SRB in the whole bacterial community decreased from approximately 32% in downhole samples to less than 5%. The lift of Ktzi 201 succeeded in the full restoration of the well productivity and injectivity. Additionally, the likely energy source of the SRB was largely removed by the lifting, thus ensuring the long-term preservation of the injectivity.     

Laboratory calibration of the seismo-acoustic response of CO2 saturated sandstones

Ultrasonic experiments were undertaken on CO₂ flooded sandstone core samples, both synthetic sandstones and core plugs from the CRC1 CO₂ injection well in the Otway Basin, Victoria, South Eastern. Australia. The aim of these laboratory tests was to investigate the effects of CO₂ as a pore fluid on the seismo-acoustic response of the sandstone and ultimately to provide an indication of the sensitivity of time-lapse seismic imaging of the eventual CO₂/CH₄ plume in the Otway, Waarre C formation.The synthetic sandstones were manufactured using both a proprietary calcium in situ precipitation (CIPS) process and a silica cementing technique. Samples were tested in a computer controlled triaxial pressure cell where pore pressures can be controlled independently of the confining pressures. The pressure cell is equipped with ultrasonic transducers housed in the loading platens. Consequently, effective pressures equivalent to those expected in the reservoir can be applied while ultrasonic testing is undertaken. Both compressional, P and shear waves, S were recorded via a digital oscilloscope at a range of effective pressure steps. Pore pressures were varied from 4 MPa to 17 MPa to represent both the gaseous and liquid phase regions of the CO₂ phase diagram. Similar experiments were conducted on core plugs from the Waarre C reservoir horizon obtained from the CRC1 injection well, but with an intervening brine-saturated step and in some cases with a CO₂/CH₄ mix of 80%/20% molar fraction which is representative of the field situation. However, the pore pressure in these experiments was held at 4 MPa. Finally, acoustic impedances and reflection coefficients were calculated for the reservoir using Gassmann theory and the implications for imaging the CO₂ plume is discussed.     

Role and impact of CO2–rock interactions during CO2 storage in sedimentary rocks

Before implementing CO₂ storage on a large scale its viability regarding injectivity, containment and long-term safety for both humans and environment is crucial. Assessing CO₂–rock interactions is an important part of that as these potentially affect physical properties through highly coupled processes. Increased understanding of the physical impact of injected CO₂ during recent years including buoyancy driven two-phase flow and convective mixing elucidated potential CO₂ pathways and indicated where and when CO₂–rock interactions are potentially occurring. Several areas of interactions can be defined: (1) interactions during the injection phase and in the near well environment, (2) long-term reservoir and cap rock interactions, (3) CO₂–rock interactions along leakage pathways (well, cap rock and fault), (4) CO₂–rock interactions causing potable aquifer contamination as a consequence of leakage, (5) water–rock interactions caused by aquifer contamination through the CO₂ induced displacement of brines and finally engineered CO₂–rock interactions (6). The driving processes of CO₂–rock interactions are discussed as well as their potential impact in terms of changing physical parameters. This includes dissolution of CO₂ in brines, acid induced reactions, reactions due to brine concentration, clay desiccation, pure CO₂–rock interactions and reactions induced by other gases than CO₂. Based on each interaction environment the main aspects that are possibly affecting the safety and/or feasibility of the CO₂ storage scheme are reviewed and identified. Then the methodologies for assessing CO₂–rock interactions are discussed. High priority research topics include the impact of other gaseous compounds in the CO₂ stream on rock and cement materials, the reactivity of dry CO₂ in the absence of water, how CO₂ induced precipitation reactions affect the pore space evolution and thus the physical properties and the need for the development of coupled flow, geochemical and geomechanical models.     

Experimental study on CO2 monitoring and quantification of stored CO2 in saline formations using resistivity measurements

This paper reports CO₂ saturation estimations based on resistivity data obtained from laboratory measurements and induction logging results at the Nagaoka pilot CO₂ injection site. The laboratory experiments put in evidence that the presence of clay content tends to reduce the increase of resistivity caused by the displacement of brine by less conductive CO₂. As a result, CO₂ saturations estimated from resistivity measurements without any correction for the clay effect are considerably lower than the actual saturations. The resistivity index (RI) provides better estimates of CO₂ saturations than the Archie's equation because it requires the determination or assumption of only one rock parameter: the saturation exponent. CO₂ saturations estimated from the induction logging data acquired at Nagaoka are considerably lower than the neutron porosity changes due to displacement between brine and CO₂ in the reservoir. Even in the case of considering the De Witte's equation and the Poupon's to account for the clay effect, it was still difficult to get a good agreement with the neutron logging results. New relations based on the resistivity index with correction factors for the clay effect are developed and implemented in this study. One of these relations has proved to be effective to estimate CO₂ saturations in saline formations with high clay content.