Large-scale impact of CO2 storage in deep saline aquifers: A sensitivity study on pressure response in stratified systems

Large volumes of CO₂ captured from carbon emitters (such as coal-fired power plants) may be stored in deep saline aquifers as a means of mitigating climate change. Storing these additional fluids may cause pressure changes and displacement of native brines, affecting subsurface volumes that can be significantly larger than the CO₂ plume itself. This study aimed at determining the three-dimensional region of influence during/after injection of CO₂ and evaluating the possible implications for shallow groundwater resources, with particular focus on the effects of interlayer communication through low-permeability seals. To address these issues quantitatively, we conducted numerical simulations that provide a basic understanding of the large-scale flow and pressure conditions in response to industrial-scale CO₂ injection into a laterally open saline aquifer. The model domain included an idealized multilayered groundwater system, with a sequence of aquifers and aquitards (sealing units) extending from the deep saline storage formation to the uppermost freshwater aquifer. Both the local CO₂-brine flow around the single injection site and the single-phase water flow (with salinity changes) in the region away from the CO₂ plume were simulated. Our simulation results indicate considerable pressure buildup in the storage formation more than 100 km away from the injection zone, whereas the lateral distance migration of brine is rather small. In the vertical direction, the pressure perturbation from CO₂ storage may reach shallow groundwater resources only if the deep storage formation communicates with the shallow aquifers through sealing units of relatively high permeabilities (higher than 10^?18 m²). Vertical brine migration through a sequence of layers into shallow groundwater bodies is extremely unlikely. Overall, large-scale pressure changes appear to be of more concern to groundwater resources than changes in water quality caused by the migration of displaced saline water.     

Basin-scale hydrogeologic impacts of CO2 storage: Capacity and regulatory implications

Industrial-scale injection of CO₂ into saline formations in sedimentary basins will cause large-scale fluid pressurization and migration of native brines, which may affect valuable groundwater resources overlying the deep sequestration aquifers. In this paper, we discuss how such basin-scale hydrogeologic impacts (1) may reduce current storage capacity estimates, and (2) can affect regulation of CO₂ storage projects. Our assessment arises from a hypothetical future carbon sequestration scenario in the Illinois Basin, which involves twenty individual CO₂ storage projects (sites) in a core injection area most suitable for long-term storage. Each project is assumed to inject five million tonnes of CO₂ per year for 50 years. A regional-scale three-dimensional simulation model was developed for the Illinois Basin that captures both the local-scale CO₂–brine flow processes and the large-scale groundwater flow patterns in response to CO₂ storage. The far-field pressure buildup predicted for this selected sequestration scenario support recent studies in that environmental concerns related to near- and far-field pressure buildup may be a limiting factor on CO₂ storage capacity. In other words, estimates of storage capacity, if solely based on the effective pore volume available for safe trapping of CO₂, may have to be revised based on assessments of pressure perturbations and their potential impacts on caprock integrity and groundwater resources. Our results suggest that (1) the area that needs to be characterized in a permitting process may comprise a very large region within the basin if reservoir pressurization is considered, and (2) permits cannot be granted on a single-site basis alone because the near- and far-field hydrogeologic response may be affected by interference between individual storage sites. We also discuss some of the challenges in making reliable predictions of large-scale hydrogeologic impacts related to CO₂ sequestration projects.     

A method for quick assessment of CO2 storage capacity in closed and semi-closed saline formations

Saline aquifers of high permeability bounded by overlying/underlying seals may be surrounded laterally by low-permeability zones, possibly caused by natural heterogeneity and/or faulting. Carbon dioxide (CO₂) injection into and storage in such “closed” systems with impervious seals, or “semi-closed” systems with non-ideal (low permeability) seals, is different from that in “open” systems, from which the displaced brine can easily escape laterally. In closed or semi-closed systems, the pressure buildup caused by continuous industrial-scale CO₂ injection may have a limiting effect on CO₂ storage capacity, because geomechanical damage caused by overpressure needs to be avoided. In this research, a simple analytical method was developed for the quick assessment of the CO₂ storage capacity in such closed and semi-closed systems. This quick-assessment method is based on the fact that native brine (of an equivalent volume) displaced by the cumulative injected CO₂ occupies additional pore volume within the storage formation and the seals, provided by pore and brine compressibility in response to pressure buildup. With non-ideal seals, brine may also leak through the seals into overlying/underlying formations. The quick-assessment method calculates these brine displacement contributions in response to an estimated average pressure buildup in the storage reservoir. The CO₂ storage capacity and the transient domain-averaged pressure buildup estimated through the quick-assessment method were compared with the “true” values obtained using detailed numerical simulations of CO₂ and brine transport in a two-dimensional radial system. The good agreement indicates that the proposed method can produce reasonable approximations for storage–formation–seal systems of various geometric and hydrogeological properties.     

Evaluation of large-scale CO2 storage on fresh-water sections of aquifers: An example from the Texas Gulf Coast Basin

Large-scale injections of CO₂ into subsurface saline aquifers have been proposed to remediate climate change related to buildup of green house gases in the atmosphere. The pressure buildup caused by such injections may impact a volume of the basin significantly larger than the CO₂ plume itself. In areas with hydrological settings similar to the Gulf Coast Basin, the perturbation of the flow-field in deep parts of the basin could result in brines or brackish water being pushed up-dip into unconfined sections of the same formations or into the capture zone of fresh-water wells. The premise of the current study is that the details of multiple-phase flow processes necessary to model the near field evolution of the CO₂ plume are not necessary to describe the impact of the pressure anomaly on up-dip aquifers. This paper quantitatively explores conditions under which shallow groundwater would be impacted by up-dip displacement of brines, utilizing an existing carefully calibrated flow model. Modeling an injection of water, arguably equivalent to 50 million tons of CO₂/year for 50 years resulted in an average water-table rise of 1 m, with minor increase in stream baseflow and larger increase in ground water evapotranspiration, but no significant change in salinity.     

Assessing the economic feasibility of regional deep saline aquifer CO2 injection and storage: A geomechanics-based workflow applied to the Rose Run sandstone in Eastern Ohio, USA

Typical top-down regional assessments of CO₂ storage feasibility are sufficient for determining the maximum volumetric capacity of deep saline aquifers. However, they do not reflect the regional economic feasibility of storage. This is controlled, in part, by the number and type of injection wells that are necessary to achieve regional CO₂ storage goals. In contrast, the geomechanics-based assessment workflow that we present in this paper follows a bottom-up approach for evaluating regional deep saline aquifer CO₂ storage feasibility. The CO₂ storage capacity of an aquifer is a function of its porous volume as well as its CO₂ injectivity. For a saline aquifer to be considered feasible in this assessment it must be able to store a specified amount of CO₂ at a reasonable cost per ton of CO₂. The proposed assessment workflow has seven steps that include (1) defining the storage project and goals, (2) characterizing the geology and developing a geomechanical model of the aquifer, (3) constructing 3D aquifer models, (4) simulating CO₂ injection, (5,6) evaluating CO₂ injection and storage feasibility (with and without injection well stimulation), and (7) determining whether it is economically feasible to proceed with the storage project. The workflow was applied to a case study of the Rose Run sandstone aquifer in the Eastern Ohio River Valley, USA. We found that it is feasible in this region to inject 113 Mt CO₂/year for 30 years at an associated well cost of less than US $1.31/t CO₂, but only if injectivity enhancement techniques such as hydraulic fracturing and injection induced micro-seismicity are implemented.     

Methodology for CO2 chain analysis

The paper presents a methodology for CO₂ chain analysis with particular focus on the impact of technology development on the total system economy. The methodology includes the whole CO₂ chain; CO₂ source, CO₂ capture, transport and storage in aquifers or in oil reservoirs for enhanced oil recovery. It aims at supporting the identification of feasible solutions and assisting the selection of the most cost-effective options for carbon capture and storage. To demonstrate the applicability of the methodology a case study has been carried out to illustrate the possible impact of technology improvements and market development. The case study confirms that the CO₂-quota price to a large extent influence the project economy and dominates over potential technology improvements. To be economic feasible, the studied chains injecting the CO₂ in oil reservoirs for increased oil production require a CO₂-quota price in the range of 20–27 €/tonne CO₂, depending on the technology breakthrough. For the chains based on CO₂ storage in saline aquifers, the corresponding CO₂-quota price varies up to about 40 €/tonne CO₂.     

Screening and selection of sites for CO2 sequestration based on pressure buildup

This paper presents a simple methodology for estimating pressure pressure buildup due to the injection of supercritical CO₂into a saline formation, and the limiting pressure at which the formation starts to fracture. Pressure buildup is calculated using the approximate solution of Mathias et al. [Mathias, S.A., Hardisty, P.E., Trudell, M.R., Zimmerman, R.W., 2009. Approximate solutions for pressure buildup during CO₂ injection in brine aquifers. Transp. Porous Media. doi:10.1007/s11242-008-9316-7], which accounts for two-phase Forchheimer flow (of supercritical CO₂ and brine) in a compressible porous medium. Compressibility of the rock formation and both fluid phases are also accounted for. Injection pressure is assumed to be limited by the pressure required to fracture the rock formation. Fracture development is assumed to occur when pore pressures exceed the minimum principal stress, which in turn is related to the Poisson’s ratio of the rock formation. Detailed guidance is also offered concerning the estimation of viscosity, density and compressibility for the brine and CO₂. Example calculations are presented in the context of data from the Plains CO₂ Reduction (PCOR) Partnership. Such a methodology will be useful for screening analysis of potential CO₂ injection sites to identify which are worthy of further investigation.     

Integration of counter-current relative permeability in the simulation of CO2 injection into saline aquifers

Carbon dioxide (CO₂) injection into saline aquifers is one of the promising options to sequester large amounts of CO₂ in geological formations. During as well as after injection of CO₂ into an aquifer, CO₂ migrates towards the top of the formation due to density differences between the formation brine and the injected CO₂. The time scales of CO₂ migration towards the top of an aquifer and the fraction of CO₂ that is trapped as residual gas depends strongly on the driving forces that are acting on the injected CO₂.When CO₂ migrates to the top of an aquifer, brine may be displaced downwards in a counter-current flow setting particularly during the injection period. A majority of the published work on counter-current flow settings have reported significant reductions in the associated relative permeability functions as compared to co-current measurements. However, this phenomenon has not yet been considered in the simulation of CO₂ storage into saline aquifers.In this paper we study the impact of changes in mobility for the two-phase brine/CO₂ system as a result of transitions between co- and counter-current flow settings. We have included this effect in a simulator and studied the impact of the related mobility reduction on the saturation distribution and residual saturation of CO₂ in aquifers over relevant time scales. We demonstrate that the reduction in relative permeability in the vertical direction changes the plume migration pattern and has an impact on the amount of gas that is trapped as a function of time. This is to our best knowledge the first attempt to integrate counter-current relative permeability into the simulation of injection and subsequent migration of CO₂ in aquifers. The results and analysis presented in this paper are directly relevant to all ongoing activities related to the design of large-scale CO₂ storage in saline aquifers.     

CO2 storage capacity estimation: Methodology and gaps

Implementation of CO₂ capture and geological storage (CCGS) technology at the scale needed to achieve a significant and meaningful reduction in CO₂ emissions requires knowledge of the available CO₂ storage capacity. CO₂ storage capacity assessments may be conducted at various scales—in decreasing order of size and increasing order of resolution: country, basin, regional, local and site-specific. Estimation of the CO₂ storage capacity in depleted oil and gas reservoirs is straightforward and is based on recoverable reserves, reservoir properties and in situ CO₂ characteristics. In the case of CO₂-EOR, the CO₂ storage capacity can be roughly evaluated on the basis of worldwide field experience or more accurately through numerical simulations. Determination of the theoretical CO₂ storage capacity in coal beds is based on coal thickness and CO₂ adsorption isotherms, and recovery and completion factors. Evaluation of the CO₂ storage capacity in deep saline aquifers is very complex because four trapping mechanisms that act at different rates are involved and, at times, all mechanisms may be operating simultaneously. The level of detail and resolution required in the data make reliable and accurate estimation of CO₂ storage capacity in deep saline aquifers practical only at the local and site-specific scales. This paper follows a previous one on issues and development of standards for CO₂ storage capacity estimation, and provides a clear set of definitions and methodologies for the assessment of CO₂ storage capacity in geological media. Notwithstanding the defined methodologies suggested for estimating CO₂ storage capacity, major challenges lie ahead because of lack of data, particularly for coal beds and deep saline aquifers, lack of knowledge about the coefficients that reduce storage capacity from theoretical to effective and to practical, and lack of knowledge about the interplay between various trapping mechanisms at work in deep saline aquifers.     

Simultaneous CO2 injection and water production to optimise aquifer storage capacity

The estimates for geological CO₂ storage capacity worldwide vary, but it is generally believed that the capacity in saline aquifers will be sufficient for the amounts of CO₂ that will need to be stored. The effort required to select and qualify a geological storage site for safe storage will, however, be significant and storage capacity may be a limited resource regionally. Both from a economic and resource management perspective it is therefore important that potential storage sites are exploited to their full potential.In static capacity estimates, where the maximum stored amount of CO₂ is given as a fraction of the formation pore volume, typically arrive at efficiency factors in the range of a few per cents. Recent work has shown that when the dynamic behaviour of the injected CO₂ is taken into account, the efficiency factor will be reduced because of the increase in pore pressure in the region around the injection well(s). The increase in pore pressure will propagate much further than the CO₂. The EU directive on geological CO₂ storage specifically addresses the restriction that will apply when different storage sites are interacting due to pressure communication. Consequently, the pore pressure increase at the boundary of the storage license area will be an important limiting factor for the amount of CO₂ that can be injected.One obvious method to control the pore pressure is to produce water from the aquifer at some distance from the CO₂ injection wells. This paper discusses results from simulations of CO₂ injection in two aquifers on the Norwegian Continental Shelf; the Johansen aquifer and the southern part of the Utsira aquifer. These aquifers are candidates for injection of CO₂ shipped out via pipeline from the Norwegian West Coast. The injected amounts of CO₂ over a period of 50 years are 0.518 Gtonne for the Johansen aquifer and 1.04 Gtonne for the Utsira aquifer.Several design options for the injection operations are investigated: Injection of CO₂ without water production; injection into several wells to distribute the injected fluids and reduce the local pressure increase around each injection well; and injection with simultaneous production of water from one or more wells. The boundaries of the aquifer formations are assumed closed in all simulations. The possible consequences of other types of boundary conditions (semi-closed or open) are briefly discussed.     

Coupled hydromechanical modeling of CO2 sequestration in deep saline aquifers

Sequestration of carbon dioxide (CO₂) in deep saline aquifers has emerged as an option for reducing greenhouse gas emissions to the atmosphere. The large amounts of supercritical CO₂ that need to be injected into deep saline aquifers may cause large fluid pressure increases. The resulting overpressure may promote reactivation of sealed fractures or the creation of new ones in the caprock seal. This could lead to escape routes for CO₂. In order to assess the probability of such an event, we model an axisymmetric horizontal aquifer–caprock system, including hydromechanical coupling. We study the failure mechanisms, using a viscoplastic approach. Simulations illustrate that, depending on boundary conditions, the least favorable moment takes place at the beginning of injection. Initially, fluid pressure rises sharply because of a reduction in permeability due to desaturation. Once CO₂ fills the pores in the vicinity of the injection well and a capillary fringe is fully developed, the less viscous CO₂ displaces the brine and the capillary fringe laterally. The overpressure caused by the permeability reduction within the capillary fringe due to desaturation decreases with distance from the injection well. This results in a drop in fluid pressure buildup with time, which leads to a safer situation. Nevertheless, in the presence of low-permeability boundaries, fluid pressure continues to rise in the whole aquifer. This occurs when the radius of influence of the injection reaches the outer boundary. Thus, caprock integrity might be compromised in the long term.     

Intermediate storage of carbon dioxide in geological formations: A technical perspective

Enhanced oil recovery (EOR) through CO₂ flooding has been practiced on a commercial basis for the last 35 years and continues today at several sites, currently injecting in total over 30 million tons of CO₂ annually. This practice is currently exclusively for economic gain, but can potentially contribute to the reduction of emissions of greenhouse gases provided it is implemented on a large scale. Optimal operations in distributing CO₂ to CO₂-EOR or enhanced gas recovery (EGR) projects (referred to here collectively as CO₂-EHR) on a large scale and long time span imply that intermediate storage of CO₂ in geological formations may be a key component. Intermediate storage is defined as the storage of CO₂ in geological media for a limited time span such that the CO₂ can be sufficiently reproduced for later use in CO₂-EHR. This paper investigates the technical aspects, key individual parameters and possibilities of intermediate storage of CO₂ in geological formations aiming at large scale implementation of carbon dioxide capture and storage (CCS) for deep emission reduction. The main parameters are thus the depth of injection and density, CO₂ flow and transport processes, storage mechanisms, reservoir heterogeneity, the presence of impurities, the type of the reservoirs and the duration of intermediate storage. Structural traps with no flow of formation water combined with proper injection planning such as gas-phase injection favour intermediate storage in deep saline aquifers. In depleted oil and gas fields, high permeability, homogeneous reservoirs with structural traps (e.g. anticlinal structures) are good candidates for intermediate CO₂ storage. Intuitively, depleted natural gas reservoirs can be potential candidates for intermediate storage of carbon dioxide due to similarity in storage characteristics.     

Water/acid gas interfacial tensions and their impact on acid gas geological storage

Acid gas geological disposal is a promising process to reduce CO₂ atmospheric emissions and an environment-friendly and economic alternative to the transformation of H₂S into sulphur by the Claus process. Acid gas confinement in geological formations is to a large extent controlled by the capillary properties of the water/acid–gas/caprock system, because a significant fraction of the injected gas rises buoyantly and accumulates beneath the caprock. These properties include the water/acid gas interfacial tension (IFT), to which the so-called capillary entry pressure of the gas in the water-saturated caprock is proportional. In this paper we present the first ever systematic water/acid gas IFT measurements carried out by the pendant drop technique under geological storage conditions. We performed IFT measurements for water/H₂S systems over a large range of pressure (up to P = 15 MPa) and temperature (up to T = 120 °C). Water/H₂S IFT decreases with increasing P and levels off at around 9–10 mN/m at high T (≥70 °C) and P (>12 MPa). The latter values are around 30–40% of water/CO₂ IFTs, and around 20% of water/CH₄ IFTs at similar T and P conditions. The IFT between water and a CO₂ + H₂S mixture at T = 77 °C and P > 7.5 MPa is observed to be approximately equal to the molar average IFT of the water/CO₂ and water/H₂S binary mixtures. Thus, when the H₂S content in the stored acid gas increases the capillary entry pressure decreases, together with the maximum height of acid gas column and potential storage capacity of a given geological formation. Hence, considerable attention should be exercised when refilling with a H₂S-rich acid gas a depleted gas reservoir, or a depleted oil reservoir with a gas cap: in the case of hydrocarbon reservoirs that were initially (i.e., at the time of their discovery) close to capillary leakage, acid gas leakage through the caprock will inevitably occur if the refilling pressure approaches the initial reservoir pressure.     

Assessment of basin-scale hydrologic impacts of CO2 sequestration,Illinois basin

Idealized, basin-scale sharp-interface models of CO₂ injection were constructed for the Illinois basin. Porosity and permeability were decreased with depth within the Mount Simon Formation. Eau Claire confining unit porosity and permeability were kept fixed. We used 726 injection wells located near 42 power plants to deliver 80 million metric tons of CO₂/year. After 100 years of continuous injection, deviatoric fluid pressures varied between 5.6 and 18 MPa across central and southern part of the Illinois basin. Maximum deviatoric pressure reached about 50% of lithostatic levels to the south. The pressure disturbance (>0.03 MPa) propagated 10–25 km away from the injection wells resulting in significant well–well pressure interference. These findings are consistent with single-phase analytical solutions of injection. The radial footprint of the CO₂ plume at each well was only 0.5–2 km after 100 years of injection. Net lateral brine displacement was insignificant due to increasing radial distance from injection well and leakage across the Eau Claire confining unit. On geologic time scales CO₂ would migrate northward at a rate of about 6 m/1000 years. Because of paleo-seismic events in this region (M5.5–M7.5), care should be taken to avoid high pore pressures in the southern Illinois basin.     

Scenario simulations of CO2 injection feasibility, plume migration and storage in a saline aquifer, Scania, Sweden

Deep saline aquifers have large capacity for geological CO₂ storage, but are generally not as well characterized as petroleum reservoirs. We here aim at quantifying effects of uncertain hydraulic parameters and uncertain stratigraphy on CO₂ injectivity and migration, and provide a first feasibility study of pilot-scale CO₂ injection into a multilayered saline aquifer system in southwest Scania, Sweden. Four main scenarios are developed, corresponding to different possible interpretations of available site data. Simulation results show that, on the one hand, stratigraphic uncertainty (presence/absence of a thin mudstone/claystone layer above the target storage formation) leads to large differences in predicted CO₂ storage in the target formation at the end of the test (ranging between 11% and 98% of injected CO₂ remaining), whereas other parameter uncertainty (in formation and cap rock permeabilities) has small impact. On the other hand, the latter has large impact on predicted injectivity, on which stratigraphic uncertainty has small impact. Salt precipitation at the border of the target storage formation affects CO₂ injectivity for all considered scenarios and injection rates. At low injection rates, salt is deposited also within the formation, considerably reducing its availability for CO₂ storage.     

Geological storage of CO2 in saline aquifers—A review of the experience from existing storage operations

The experience from CO₂ injection at pilot projects (Frio, Ketzin, Nagaoka, US Regional Partnerships) and existing commercial operations (Sleipner, Snøhvit, In Salah, acid-gas injection) demonstrates that CO₂ geological storage in saline aquifers is technologically feasible. Monitoring and verification technologies have been tested and demonstrated to detect and track the CO₂ plume in different subsurface geological environments. By the end of 2008, approximately 20 Mt of CO₂ had been successfully injected into saline aquifers by existing operations. Currently, the highest injection rate and total storage volume for a single storage operation are approximately 1 Mt CO₂/year and 25 Mt, respectively. If carbon capture and storage (CCS) is to be an effective option for decreasing greenhouse gas emissions, commercial-scale storage operations will require orders of magnitude larger storage capacity than accessed by the existing sites. As a result, new demonstration projects will need to develop and test injection strategies that consider multiple injection wells and the optimisation of the usage of storage space. To accelerate large-scale CCS deployment, demonstration projects should be selected that can be readily employed for commercial use; i.e. projects that fully integrate the capture, transport and storage processes at an industrial emissions source.     

Carbon dioxide storage capacity in uneconomic coal beds in Alberta,Canada: Methodology,potential and site identification

Methodology is presented for a first-order regional-scale estimation of CO₂ storage capacity in coals under sub-critical conditions, which is subsequently applied to Cretaceous-Tertiary coal beds in Alberta, Canada. Regions suitable for CO₂ storage have been defined on the basis of groundwater depth and CO₂ phase at in situ conditions. The theoretical CO₂ storage capacity was estimated on the basis of CO₂ adsorption isotherms measured on coal samples, and it varies between ∼20 kt CO₂/km² and 1260 kt CO₂/km², for a total of approximately 20 Gt CO₂. This represents the theoretical storage capacity limit that would be attained if there would be no other gases present in the coals or they would be 100% replaced by CO₂, and if all the coals will be accessed by CO₂. A recovery factor of less than 100% and a completion factor less than 50% reduce the theoretical storage capacity to an effective storage capacity of only 6.4 Gt CO₂. Not all the effective CO₂ storage capacity will be utilized because it is uneconomic to build the necessary infrastructure for areas with low storage capacity per unit surface. Assuming that the economic threshold to develop the necessary infrastructure is 200 kt CO₂/km², then the CO₂ storage capacity in coal beds in Alberta is greatly reduced further to a practical capacity of only ∼800 Mt CO₂.     

Coupled reservoir-geomechanical analysis of CO2 injection and ground deformations at In Salah,Algeria

In Salah Gas Project in Algeria has been injecting 0.5–1 million tonnes CO₂ per year over the past 5 years into a water-filled strata at a depth of about 1800–1900 m. Unlike most CO₂ storage sites, the permeability of the storage formation is relatively low and comparatively thin with a thickness of about 20 m. To ensure adequate CO₂ flow-rates across the low-permeability sand-face, the In Salah Gas Project decided to use long-reach (about 1–1.5 km) horizontal injection wells. In an ongoing research project we use field data and coupled reservoir-geomechanical numerical modeling to assess the effectiveness of this approach and to investigate monitoring techniques to evaluate the performance of a CO₂ injection operation in relatively low-permeability formations. Among the field data used are ground surface deformations evaluated from recently acquired satellite-based inferrometry (InSAR). The InSAR data shows a surface uplift on the order of 5 mm per year above active CO₂ injection wells and the uplift pattern extends several km from the injection wells. In this paper we use the observed surface uplift to constrain our coupled reservoir-geomechanical model and conduct sensitivity studies to investigate potential causes and mechanisms of the observed uplift. The results of our analysis indicate that most of the observed uplift magnitude can be explained by pressure-induced, poro-elastic expansion of the 20-m-thick injection zone, but there could also be a significant contribution from pressure-induced deformations within a 100-m-thick zone of shaly sands immediately above the injection zone.     

Monitoring of the microbial community composition in saline aquifers during CO2 storage by fluorescence in situ hybridisation

This study reveals the first analyses of the composition and activity of the microbial community of a saline CO₂ storage aquifer. Microbial monitoring during CO₂ injection has been reported. By using fluorescence in situ hybridisation (FISH), we have shown that the microbial community was strongly influenced by the CO₂ injection. Before CO₂ arrival, up to 6 × 10⁶ cells ml⁻¹ were detected by DAPI staining at a depth of 647 m below the surface. The microbial community was dominated by the domain Bacteria that represented approximately 60% to 90% of the total cell number, with Proteobacteria and Firmicutes as the most abundant phyla comprising up to 47% and 45% of the entire population, respectively. Both the total cell counts as well as the counts of the specific physiological groups revealed quantitative and qualitative changes after CO₂ arrival. Our study revealed temporal outcompetition of sulphate-reducing bacteria by methanogenic archaea. In addition, an enhanced activity of the microbial population after five months CO₂ storage indicated that the bacterial community was able to adapt to the extreme conditions of the deep biosphere and to the extreme changes of these atypical conditions.     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.