CO2 storage capacity estimation: Methodology and gaps

Implementation of CO₂ capture and geological storage (CCGS) technology at the scale needed to achieve a significant and meaningful reduction in CO₂ emissions requires knowledge of the available CO₂ storage capacity. CO₂ storage capacity assessments may be conducted at various scales—in decreasing order of size and increasing order of resolution: country, basin, regional, local and site-specific. Estimation of the CO₂ storage capacity in depleted oil and gas reservoirs is straightforward and is based on recoverable reserves, reservoir properties and in situ CO₂ characteristics. In the case of CO₂-EOR, the CO₂ storage capacity can be roughly evaluated on the basis of worldwide field experience or more accurately through numerical simulations. Determination of the theoretical CO₂ storage capacity in coal beds is based on coal thickness and CO₂ adsorption isotherms, and recovery and completion factors. Evaluation of the CO₂ storage capacity in deep saline aquifers is very complex because four trapping mechanisms that act at different rates are involved and, at times, all mechanisms may be operating simultaneously. The level of detail and resolution required in the data make reliable and accurate estimation of CO₂ storage capacity in deep saline aquifers practical only at the local and site-specific scales. This paper follows a previous one on issues and development of standards for CO₂ storage capacity estimation, and provides a clear set of definitions and methodologies for the assessment of CO₂ storage capacity in geological media. Notwithstanding the defined methodologies suggested for estimating CO₂ storage capacity, major challenges lie ahead because of lack of data, particularly for coal beds and deep saline aquifers, lack of knowledge about the coefficients that reduce storage capacity from theoretical to effective and to practical, and lack of knowledge about the interplay between various trapping mechanisms at work in deep saline aquifers.     

Water/acid gas interfacial tensions and their impact on acid gas geological storage

Acid gas geological disposal is a promising process to reduce CO₂ atmospheric emissions and an environment-friendly and economic alternative to the transformation of H₂S into sulphur by the Claus process. Acid gas confinement in geological formations is to a large extent controlled by the capillary properties of the water/acid–gas/caprock system, because a significant fraction of the injected gas rises buoyantly and accumulates beneath the caprock. These properties include the water/acid gas interfacial tension (IFT), to which the so-called capillary entry pressure of the gas in the water-saturated caprock is proportional. In this paper we present the first ever systematic water/acid gas IFT measurements carried out by the pendant drop technique under geological storage conditions. We performed IFT measurements for water/H₂S systems over a large range of pressure (up to P = 15 MPa) and temperature (up to T = 120 °C). Water/H₂S IFT decreases with increasing P and levels off at around 9–10 mN/m at high T (≥70 °C) and P (>12 MPa). The latter values are around 30–40% of water/CO₂ IFTs, and around 20% of water/CH₄ IFTs at similar T and P conditions. The IFT between water and a CO₂ + H₂S mixture at T = 77 °C and P > 7.5 MPa is observed to be approximately equal to the molar average IFT of the water/CO₂ and water/H₂S binary mixtures. Thus, when the H₂S content in the stored acid gas increases the capillary entry pressure decreases, together with the maximum height of acid gas column and potential storage capacity of a given geological formation. Hence, considerable attention should be exercised when refilling with a H₂S-rich acid gas a depleted gas reservoir, or a depleted oil reservoir with a gas cap: in the case of hydrocarbon reservoirs that were initially (i.e., at the time of their discovery) close to capillary leakage, acid gas leakage through the caprock will inevitably occur if the refilling pressure approaches the initial reservoir pressure.     

Integration of counter-current relative permeability in the simulation of CO2 injection into saline aquifers

Carbon dioxide (CO₂) injection into saline aquifers is one of the promising options to sequester large amounts of CO₂ in geological formations. During as well as after injection of CO₂ into an aquifer, CO₂ migrates towards the top of the formation due to density differences between the formation brine and the injected CO₂. The time scales of CO₂ migration towards the top of an aquifer and the fraction of CO₂ that is trapped as residual gas depends strongly on the driving forces that are acting on the injected CO₂.When CO₂ migrates to the top of an aquifer, brine may be displaced downwards in a counter-current flow setting particularly during the injection period. A majority of the published work on counter-current flow settings have reported significant reductions in the associated relative permeability functions as compared to co-current measurements. However, this phenomenon has not yet been considered in the simulation of CO₂ storage into saline aquifers.In this paper we study the impact of changes in mobility for the two-phase brine/CO₂ system as a result of transitions between co- and counter-current flow settings. We have included this effect in a simulator and studied the impact of the related mobility reduction on the saturation distribution and residual saturation of CO₂ in aquifers over relevant time scales. We demonstrate that the reduction in relative permeability in the vertical direction changes the plume migration pattern and has an impact on the amount of gas that is trapped as a function of time. This is to our best knowledge the first attempt to integrate counter-current relative permeability into the simulation of injection and subsequent migration of CO₂ in aquifers. The results and analysis presented in this paper are directly relevant to all ongoing activities related to the design of large-scale CO₂ storage in saline aquifers.     

A solution against well cement degradation under CO2 geological storage environment

Capturing and storing carbon dioxide (CO₂) underground for thousands of years is one way to reduce atmospheric greenhouse gases, often associated with global warming. Leakage through wells is one of the major issues when storing CO₂ in depleted oil or gas reservoirs. CO₂-injection candidates may be new wells, or old wells that are active, closed or abandoned. In all cases, it is critical to ensure that the long-term integrity of the storage wells is not compromised. The loss of well integrity may often be explained by the geochemical alteration of hydrated cement that is used to isolate the annulus across the producing/injection intervals in CO₂-related wells. However, even before any chemical degradation, changes in downhole conditions due to supercritical CO₂ injections can also be responsible for cement debonding from the casing and/or from the formation, leading to rapid CO₂ leakage. A new cement with better CO₂ resistance is compared with conventional cement using experimental procedure and methodology simulating the interaction of set cement with injected, supercritical CO₂ under downhole conditions. Geochemical experimental data and a mechanical modeling approach are presented. The use of adding expanding property to this new cement to avoid microannulus development during the CO₂ injection is discussed.     

Coalbed methane reservoir data and simulator parameter uncertainty modelling for CO2 storage performance assessment

Laboratory studies and a number of field pilots have demonstrated that CO₂ injection into coal seams has the potential to enhance coalbed methane (CBM) recovery with the added advantage that most of the injected CO₂ can be stored permanently in coal. The concept of storing CO₂ in geologic formations as a safe and effective greenhouse gas mitigation option requires public and regulatory acceptance. In this context it is important to develop a good understanding of the reservoir performance, uncertainties and the risks that are associated with geological storage. The paper presented refers to the sources of uncertainty involved in CO₂ storage performance assessment in coalbed methane reservoirs and demonstrates their significance using extensive digital well log data representing the Manville coals in Alberta, Canada. The spatial variability of the reservoir properties was captured through geostatistical analysis, and sequential Gaussian simulations of these provided multiple realisations for the reservoir simulator inputs. A number of CO₂ injection scenarios with variable matrix swelling coefficients were evaluated using a 2D reservoir model and spatially distributed realisations of total net thickness and permeability.     

Long-term variations of CO2 trapped in different mechanisms in deep saline formations: A case study of the Songliao Basin,China

The geological storage of CO₂ in deep saline formations is increasing seen as a viable strategy to reduce the release of greenhouse gases to the atmosphere. There are numerous sedimentary basins in China, in which a number of suitable CO₂ geologic reservoirs are potentially available. To identify the multi-phase processes, geochemical changes and mineral alteration, and CO₂ trapping mechanisms after CO₂ injection, reactive geochemical transport simulations using a simple 2D model were performed. Mineralogical composition and water chemistry from a deep saline formation of Songliao Basin were used. Results indicate that different storage forms of CO₂ vary with time. In the CO₂ injection period, a large amount of CO₂ remains as a free supercritical phase (gas trapping), and the amount dissolved in the formation water (solubility trapping) gradually increases. Later, gas trapping decrease, solubility trapping increases significantly due to the migration and diffusion of CO₂ plume and the convective mixing between CO₂-saturated water and unsaturated water, and the amount trapped by carbonate minerals increases gradually with time. The residual CO₂ gas keeps dissolving into groundwater and precipitating carbonate minerals. For the Songliao Basin sandstone, variations in the reaction rate and abundance of chlorite, and plagioclase composition affect significantly the estimates of mineral alteration and CO₂ storage in different trapping mechanisms. The effect of vertical permeability and residual gas saturation on the overall storage is smaller compared to the geochemical factors. However, they can affect the spatial distribution of the injected CO₂ in the formations. The CO₂ mineral trapping capacity could be in the order of 10 kg/m³ medium for the Songliao Basin sandstone, and may be higher depending on the composition of primary aluminosilicate minerals especially the content of Ca, Mg, and Fe.     

Scenario simulations of CO2 injection feasibility, plume migration and storage in a saline aquifer, Scania, Sweden

Deep saline aquifers have large capacity for geological CO₂ storage, but are generally not as well characterized as petroleum reservoirs. We here aim at quantifying effects of uncertain hydraulic parameters and uncertain stratigraphy on CO₂ injectivity and migration, and provide a first feasibility study of pilot-scale CO₂ injection into a multilayered saline aquifer system in southwest Scania, Sweden. Four main scenarios are developed, corresponding to different possible interpretations of available site data. Simulation results show that, on the one hand, stratigraphic uncertainty (presence/absence of a thin mudstone/claystone layer above the target storage formation) leads to large differences in predicted CO₂ storage in the target formation at the end of the test (ranging between 11% and 98% of injected CO₂ remaining), whereas other parameter uncertainty (in formation and cap rock permeabilities) has small impact. On the other hand, the latter has large impact on predicted injectivity, on which stratigraphic uncertainty has small impact. Salt precipitation at the border of the target storage formation affects CO₂ injectivity for all considered scenarios and injection rates. At low injection rates, salt is deposited also within the formation, considerably reducing its availability for CO₂ storage.     

Economic evaluation of the geological storage of CO2 considering the scale of economy

CO₂ capture and storage (CCS) technology is expected to play an important role in the efforts directed toward long-term CO₂ emission reduction. This paper analyzes the cost of the geological storage of CO₂ in Japan in order to consider future research, development and deployment (RD&D); these would be based on the information of the obtained cost structure. According to the analysis results, the costs, particularly those of the transportation by pipeline and of CO₂ injection, strongly depend on the scale of the facilities. Therefore, the distance of the transportation of CO₂ should be minimized in the case of small-scale storage, particularly in Japan. In addition, the potential injection rate per well is another key factor for the injection cost. Based on the analyzed cost, the injection cost of the geological storage of CO₂ in Japan for individual storage sites is estimated, and the cost–potential curve is obtained. A mixed-integer programming model has been developed to take into account these characteristics of the CCS technology and its adverse effects arising from the scale of economy with regard to the transportation and injection cost for the geological storage of CO₂. The model is designed to evaluate CCS and other CO₂ mitigation technologies in the energy systems of Japan. With all these adverse effects due to the scale of economy, the geological storage of CO₂ will be one of the important options for CO₂ emission reduction in Japan.     

Lessons learned from natural and industrial analogues for storage of carbon dioxide

The deployment of CCS (carbon capture and storage) at industrial scale implies the development of effective monitoring tools. Noble gases are tracers usually proposed to track CO₂. This methodology, combined with the geochemistry of carbon isotopes, has been tested on available analogues.At first, gases from natural analogues were sampled in the Colorado Plateau and in the French carbogaseous provinces, in both well-confined and leaking-sites. Second, we performed a 2-years tracing experience on an underground natural gas storage, sampling gas each month during injection and withdrawal periods.In natural analogues, the geochemical fingerprints are dependent on the containment criterion and on the geological context, giving tools to detect a leakage of deep-CO₂ toward surface. This study also provides information on the origin of CO₂, as well as residence time of fluids within the crust and clues on the physico-chemical processes occurring during the geological story.The study on the industrial analogue demonstrates the feasibility of using noble gases as tracers of CO₂. Withdrawn gases follow geochemical trends coherent with mixing processes between injected gas end-members. Physico-chemical processes revealed by the tracing occur at transient state.These two complementary studies proved the interest of geochemical monitoring to survey the CO₂ behaviour, and gave information on its use.     

Investigations on CO2 storage capacity in saline aquifers—Part 2: Estimation of storage capacity coefficients

Many studies on geological carbon dioxide (CO₂) storage capacity neglect the influence of complex coupled processes which occur during and after the injection of CO₂. Storage capacity is often overestimated since parts of the reservoirs cannot be reached by the CO₂ plume due to gravity segregation and are thus not accessible for storage. This work investigates the effect of reservoir parameters like depth, temperature, absolute and relative permeability, and capillary pressure on the processes during CO₂ injection and thus on estimates of effective storage capacity. The applied statistical characteristics of parameters are based on a large reservoir parameter database. Different measured relative permeability relations are considered. The methodology of estimating storage capacity is discussed. Using numerical 1D and 3D experiments, detailed time-dependent storage capacity estimates are derived. With respect to the concept developed in this work, it is possible to estimate effective CO₂ storage capacity in saline aquifers. It is shown that effective CO₂ mass stored in the reservoir varies by a factor of 20 for the reservoir setups considered. A high influence of the relative permeability relation on storage capacity is shown.     

Simultaneous CO2 injection and water production to optimise aquifer storage capacity

The estimates for geological CO₂ storage capacity worldwide vary, but it is generally believed that the capacity in saline aquifers will be sufficient for the amounts of CO₂ that will need to be stored. The effort required to select and qualify a geological storage site for safe storage will, however, be significant and storage capacity may be a limited resource regionally. Both from a economic and resource management perspective it is therefore important that potential storage sites are exploited to their full potential.In static capacity estimates, where the maximum stored amount of CO₂ is given as a fraction of the formation pore volume, typically arrive at efficiency factors in the range of a few per cents. Recent work has shown that when the dynamic behaviour of the injected CO₂ is taken into account, the efficiency factor will be reduced because of the increase in pore pressure in the region around the injection well(s). The increase in pore pressure will propagate much further than the CO₂. The EU directive on geological CO₂ storage specifically addresses the restriction that will apply when different storage sites are interacting due to pressure communication. Consequently, the pore pressure increase at the boundary of the storage license area will be an important limiting factor for the amount of CO₂ that can be injected.One obvious method to control the pore pressure is to produce water from the aquifer at some distance from the CO₂ injection wells. This paper discusses results from simulations of CO₂ injection in two aquifers on the Norwegian Continental Shelf; the Johansen aquifer and the southern part of the Utsira aquifer. These aquifers are candidates for injection of CO₂ shipped out via pipeline from the Norwegian West Coast. The injected amounts of CO₂ over a period of 50 years are 0.518 Gtonne for the Johansen aquifer and 1.04 Gtonne for the Utsira aquifer.Several design options for the injection operations are investigated: Injection of CO₂ without water production; injection into several wells to distribute the injected fluids and reduce the local pressure increase around each injection well; and injection with simultaneous production of water from one or more wells. The boundaries of the aquifer formations are assumed closed in all simulations. The possible consequences of other types of boundary conditions (semi-closed or open) are briefly discussed.     

The impact of heterogeneity on the distribution of CO2: Numerical simulation of CO2 storage at Ketzin

Numerical modelling of multiphase flow is an essential tool to ensure the viability of long-term and safe CO₂ storage in geological formations. Uncertainties arising from the heterogeneity of the formation and lack of knowledge of formation properties need to be assessed in order to create a model that can reproduce the data available from monitoring. In this study, we investigated the impact of unknown spatial variability in the petrophysical properties within a sandy channel facies of a fluviatile storage formation using stochastic methods in a Monte Carlo approach. The stochastic method has been applied to the Ketzin test site (CO₂SINK), and demonstrates that the deterministic homogeneous model satisfactorily predicts the first CO₂ arrival time at the Ketzin site. The equivalent permeability was adjusted to the injection pressure and is in good agreement with the hydraulic test. It has been shown that with increasing small-scale heterogeneity, the sharpness of the CO₂ front decreases and a greater volume of the reservoir is affected, which is also seen in an increased amount of dissolved CO₂. Increased anisotropy creates fingering effects, which result in higher probabilities for earlier arrival times. Generally, injectivity decreases with increasing heterogeneity.     

First assessment of sources and sinks for carbon capture and geological storage in Portugal

A preliminary study for a source–sink match for application of Carbon Capture and Storage (CCS) in Portugal is presented. The location of the main CO₂ emission sources in Portugal, existing and planned, was analysed and three main source clusters, emitting a total of 26.8 Mt/year, were defined. The three source clusters are connected by a natural gas pipeline network.CO₂ storage reservoirs are likely to be restricted to deep saline formations. Potential storage formations are described in the Porto, Lusitanian and Algarve sedimentary basins. Due to the large continental shelf, composed mainly of sedimentary rocks, it is important to consider offshore opportunities. A Geographical Information System (GIS), including information on the stratigraphy, seismicity, neotectonics and geothermal features, was used for prioritising the areas where reservoir identification and characterization studies should be conducted. Despite not showing the most promising geological conditions, the area around the deepwater harbour of Sines is given the highest priority, since sources in the area account for more than 40% of point source emissions in Portugal.     

Petrophysical analysis to investigate the effects of carbon dioxide storage in a subsurface saline aquifer at Ketzin, Germany (CO2SINK)

To test the injection behaviour of CO₂ into brine-saturated rock and to evaluate the dependence of geophysical properties on CO₂ injection, flow and exposure experiments with brine and CO₂ were performed on sandstone samples of the Stuttgart Formation representing potential reservoir rocks for CO₂ storage. The sandstone samples studied are generally fine-grained with porosities between 17 and 32% and permeabilities between 1 and 100 mD.Additional batch experiments were performed to predict the long-term behaviour of geological CO₂ storage. Reservoir rock samples were exposed over a period of several months to CO₂-saturated reservoir fluid in high-pressure vessels under in situ temperature and pressure conditions. Petrophysical parameters, porosity and the pore radius distribution were investigated before and after the experiments by NMR (Nuclear Magnetic Resonance) relaxation and mercury injection. Most of the NMR measurements of the tested samples showed a slight increase of porosity and a higher proportion of large pores.     

Numerical investigation concerning the impact of CO2 geologic storage on regional groundwater flow

Large-scale storage of carbon dioxide in saline aquifers may cause considerable pressure perturbation and brine migration in deep rock formations, which may have a significant influence on the regional groundwater system. With the help of parallel computing techniques, we conducted a comprehensive, large-scale numerical simulation of CO₂ geologic storage that predicts not only CO₂ migration, but also its impact on regional groundwater flow. As a case study, a hypothetical industrial-scale CO₂ injection in Tokyo Bay, which is surrounded by the most heavily industrialized area in Japan, was considered, and the impact of CO₂ injection on near-surface aquifers was investigated, assuming relatively high seal-layer permeability (higher than 10 microdarcy). A regional hydrogeological model with an area of about 60 km × 70 km around Tokyo Bay was discretized into about 10 million gridblocks. To solve the high-resolution model efficiently, we used a parallelized multiphase flow simulator TOUGH2-MP/ECO2N on a world-class high performance supercomputer in Japan, the Earth Simulator. In this simulation, CO₂ was injected into a storage aquifer at about 1 km depth under Tokyo Bay from 10 wells, at a total rate of 10 million tons/year for 100 years. Through the model, we can examine regional groundwater pressure buildup and groundwater migration to the land surface. The results suggest that even if containment of CO₂ plume is ensured, pressure buildup on the order of a few bars can occur in the shallow confined aquifers over extensive regions, including urban inlands.     

Pipeline design for a least-cost router application for CO2 transport in the CO2 sequestration cycle

CO₂ capture and geological storage (CCS) is considered as a viable option to mitigate greenhouse gas emissions during the transition phase towards the use of clean and renewable energy. This paper concentrates on the transport of CO₂ between source (CO₂ capture at plants) and sink (geological storage reservoirs). In the cost estimation of CO₂ transport, the pipeline diameter plays an important role. In this respect, the paper reviews equations that were used in several reports on CO₂ pipeline transport. As some parameters are not taken into account in these equations, alternative formulas are proposed which calculate the proper inner diameter size based on flow rate, pressure drop per unit length, CO₂ density, CO₂ viscosity, pipeline material roughness and topographic height differences (the Darcy–Weisbach solution) and, in addition, on the amount and type of bends (the Manning solution). Comparison between calculated diameters using the reviewed and the proposed equations demonstrate the important influence of elevation difference (which is not considered in the reviewed equations) and pipeline material roughness-related factor on the calculated diameter. Concerning the latter, it is suggested that a Darcy–Weisbach roughness height of 0.045 mm better corresponds to a Manning factor of 0.009 than higher Manning values previously proposed in literature. Comparison with the actual diameter of the Weyburn pipeline confirms the accuracy of the proposed equations. Comparison with other existing CO₂ pipelines (without pressure information) indicate that the pipelines are designed for lower pressure gradients than 25 Pa/m or for (future) higher flow rates. The proposed Manning equation is implemented in an economic least-cost route planner in order to obtain the best economic solution for pipeline trajectory and corresponding diameter.     

Dynamis CO2 quality recommendations

In the carbon capture and storage (CCS) chain, transport and storage set different requirements for the composition of the gas stream mainly containing carbon dioxide (CO₂). Currently, there is a lack of standards to define the required quality for CO₂ pipelines. This study investigates and recommends likely maximum allowable concentrations of impurities in the CO₂ for safe transportation in pipelines. The focus is on CO₂ streams from pre-combustion processes. Among the issues addressed are safety and toxicity limits, compression work, hydrate formation, corrosion and free water formation, including the cross-effect of H₂S and H₂O and of H₂O and CH₄.     

CO2 storage and enhanced coalbed methane recovery: Reservoir characterization and fluid flow simulations of the Big George coal,Powder River Basin,Wyoming, USA

Coalbeds are an attractive geological environment for storage of carbon dioxide (CO₂) because CO₂ is retained in the coal as an adsorbed phase and the cost of injection can be offset by enhanced coalbed methane (ECBM) production. This paper presents the findings of a CO₂ storage feasibility study on coalbeds in the Wyodak-Anderson coal zone of the Powder River Basin, Wyoming, USA, using reservoir characterization and fluid flow simulations. A 3D numerical model of the Big George coal was constructed using geostatistical techniques, with values of cleat and matrix permeability and porosity constrained through history-matching of production data from coalbed methane (CBM) wells in the field area.Following history-matching, several ECBM and CO₂ storage scenarios were investigated: shrinkage and swelling of the coal was either allowed or disallowed, a horizontal hydraulic fracture was either placed at the injection well or removed from the model, the number of model layers was varied between 1 and 24, and the permeability and porosity fields were constructed to be either homogeneous or heterogeneous in accordance with geostatistical models of regional variability. All simulations assumed that the injected gas was 100% CO₂ and that the coalbed was overlain by an impermeable caprock. Depending on the scenario, the simulations predicted that after 13 years of CO₂ injection, the cumulative methane production would be enhanced by a factor of 1.5–5. Including coal matrix shrinkage and swelling in the model predicted swelling near the injection well, which resulted in a slight reduction (10%) in injection rate. However, including a horizontal hydraulic fracture in the model at the base of the injection well helped mitigate the negative effect of swelling on injection rate. It was also found that six model layers were needed to have sufficient resolution in the vertical direction to account for the buoyancy effects between the gas and resident water, and that capturing the heterogeneous nature of the coal permeability and porosity fields predicted lower estimates of the storage capacity of the Wyodak-Anderson coal zone.After noting that gravity and buoyancy were the major driving forces behind gas flow within the Big George coal, several leakage scenarios were also investigated, in an effort to better understand the interplay between diffusion and flow properties on the transport and storage of CO₂. The modeling predicted that the upward migration of gas due to the buoyancy effect was faster than the diffusion of CO₂ and therefore the gas rapidly rose to the top of the coalbed and migrated into overlying strata when an impermeable caprock was not included in the model.     

Regulatory challenges and managing public perception in planning a geological storage pilot project in Australia

The implementation of geological storage of CO₂ requires not only further research and development but also the demonstration of carbon dioxide capture and storage (CCS) technology as a viable option. A pilot program is an important first step towards building industry and community confidence in the application of CCS. The Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC), Australia's leading research organisation in CCS, has initiated a comprehensive research and demonstration program in the Otway Basin in South-West Victoria. As the first project of its kind in Australia, the Otway Basin Pilot Project (OBPP) has faced a number of regulatory and organisational challenges while having to concurrently address public perception. The Otway Basin site with its natural CO₂ accumulations and many depleted natural gas fields offers an appropriate CO₂ storage site to test scientific and regulatory concepts and evaluate public response through social research. The project aims to show that CO₂ can be safely captured, transported and stored deep underground under local conditions, and also monitored and verified. Planning has been ongoing for over a year, baseline studies are underway and the project is targeted to start injection in 2007.