THE BISCAYNE AQUIFER CONTAMINATION: CLEANUP AND PREVENTION1

ABSTRACT: The Biscayne Aquifer is the sole source of drinking water for approximately three million residents of southeast Florida. Nine hazardous waste sites on the EPA National Priority List overlie this aquifer. Extensive investigation of an 80 square-mile area in metropolitan Miami detected low to moderate levels of toxic contaminants in the ground water, with volatile organic chemicals the most prevalent. The Centers for Disease Control concluded that contamination of the aquifer within the study area poses a serious potential threat to public health. Recommendations for source control and cleanup have been partially carried out. The top few feet of soil at the Miami Drum site have been excavated and relocated; ground water encountered during excavation has been withdrawn and treated, and the Northwest 58th Street Landfill has been closed. Recovery and treatment of ground water from the contaminated area was the recommended cleanup measure and has been approved by EPA and state and local agencies. A preventive action program for the Biscayne Aquifer region was also recommended for implementation by local agencies. This program consists of regulations, waste management practices, construction and treatment guidelines, and public information activities and materials. Implementing this program will help keep the Biscayne Aquifer water drinkable far into the future.     

Canadian Innovations in Siting Hazardous Waste Management Facilities

/ Siting hazardous waste facilities is an extremely complex and difficult endeavor. Public aversion to the construction of these facilities in or near their community often results in concerted opposition, referred to as the NIMBY syndrome. For the most part, siting processes do not fail because of inadequate environmental or technical considerations, but because of the adversarial decision-making strategies employed by the proponents. Innovative siting processes used in the provinces of Alberta and Manitoba offer tangible evidence of the successful application of an innovative siting approach based on the principles of decentralization of decision-making authority and full and meaningful public involvement. The purpose of this paper is to evaluate four Canadian siting processes from the perspective of public participation and access to decision-making authority. Examples of siting processes related to hazardous waste management facilities are provided from the provinces of Alberta, Manitoba, British Columbia, and Ontario. Siting has evolved from approaches dominated by top-down decision making to increasing decentralized and pluralistic approaches. Focusing on social and political concerns of potentially affected communities and on the process of decision making itself are fundamental to achieving siting success. In Alberta initially, and later in Manitoba, this new "open approach" to siting has resulted in the construction of the first two comprehensive hazardous waste treatment facilities in Canada.KEY WORDS: Hazardous waste facilities; Siting methodologies; Public participation     

Security risks in nuclear waste management: Exceptionalism,opaqueness and vulnerability

This paper analyses some potential security risks, concerning terrorism or more mundane forms of crime, such as fraud, in management of nuclear waste using a PEST scan (of political, economic, social and technical issues) and some insights of criminologists on crime prevention. Nuclear waste arises as spent fuel from ongoing energy generation or other nuclear operations, operational contamination or emissions, and decommissioning of obsolescent facilities. In international and EU political contexts, nuclear waste management is a sensitive issue, regulated specifically as part of the nuclear industry as well as in terms of hazardous waste policies. The industry involves state, commercial and mixed public–private bodies. The social and cultural dimensions – risk, uncertainty, and future generations – resonate more deeply here than in any other aspect of waste management. The paper argues that certain tendencies in regulation of the industry, claimed to be justified on security grounds, are decreasing transparency and veracity of reporting, opening up invisible spaces for management frauds, and in doing allowing a culture of impunity in which more serious criminal or terrorist risks could arise. What is needed is analysis of this ‘exceptional’ industry in terms of the normal cannons of risk assessment – a task that this paper begins.     

Chemical Warfare Materiel: Unique Regulatory Issues

In those states that have not included CWM as hazardous materials in their RCRA programs, the RCRA requirements for management of hazardous waste would not strictly apply to any of the CWM. The Army has historically implemented procedures requiring that chemical warfare agents be managed as RCRA hazardous waste regardless of the concentration, physical form, or configuration of the agent. Such application of strict hazardous waste requirements to management of potentially nonhazardous CWM can result in remedial costs well out of proportion to potential human health and environmental benefits. Recent development of chronic toxicity values for the CWM has opened the door for development of cleanup and waste management standards for waste streams or media containing small residual amounts of CWM. Implementation of this health-based approach to management of CWM remediation wastes may, in part, help to reduce potentially unnecessary hazardous waste management costs for the nonhazardous CWM.     

Monitoring the dispersal of contaminants by wildlife at nuclear weapons production and waste storage facilities

Professor of wildlife biology in the department of biological sciences, California State University. Dr K. Shawn Smallwood is a systems ecologist and may be contacted at 109 Luz Place, Davis, CA 95616, USA. Dr Jan Beyea is a physical scientist with Consulting in the Public Interest, 53 Clinton Street, Lambertville, NJ 08530, USA. The US Government produced and acquired approximately 111 t of plutonium in support of its nuclear weapons programme. Verified reports of the loss of nuclear material into the environment, including loss by animals, has raised questions regarding the monitoring programmes in place on the nuclear facilities. Given these concerns regarding the fate of stored nuclear waste, the authors conducted a review of the wildlife monitoring programme used at nuclear weapons and storage facilities by (1) reviewing the key facets of the monitoring used at the facilities, (2) evaluating published and unpublished data from the facilities and (3) incorporating data from personal site visits. The study concentrated on the Department of Energy's Hanford Reservation in rural south–central Washington and the Rocky Flats Plant in central Colorado. Based on the review, it is concluded that an improved and rigorous environmental surveillance and monitoring programme is needed at both locations. The site surveys identified frequent instances of intrusion into burial sites by animals, most of which had gone unreported by Hanford and Rocky Flats personnel. It was apparent that a significant source of potential contamination was not being adequately monitored at the nuclear waste sites. It is recommended that the development of a systematic, well-planned programme of monitoring animal intrusion on burial sites be considered, coupled with improved training for responsible personnel.     

Failing to Site Hazardous Waste Facilities Voluntarily: Implications for the Production of Sustainable Goods

A current approach to the process of siting hazardous waste facilities is to seek 'willing host' communities that will not oppose but rather voluntarily accept risky facilities. Voluntary siting strategies have been put forward as the solution to hazardous waste location problems, and there have indeed been a small number of siting successes achieved voluntarily. This paper argues that, despite claims about voluntary processes, there are indications that few 'willing host' sites will be found in response to the many that are proposed. Instead, it suggests that the limited success of siting attempts, voluntary or otherwise, signals a new phase in hazardous waste management, a shift in focus from where to site a facility to whether a good is worth producing at all if its wastes are not siteable. A characteristic of this phase is the growing influence that the disposal potential of the generated waste can have on future management decisions to produce a good. In practice, siting failure may be one of the critical turning points on the road to sustainable production. It can accomplish what technology and environmental assessments have generally been unable to do: foresee the sustainability of a good. In this way, siteability can be seen as one indicator of sustainable production. A good can be considered sustainable if the wastes associated with its production are siteable.     

A Paradigm of International Environmental Law: The Case for Controlling the Transboundary Movements of Hazardous Wastes

The production of large quantities of wastes globally has created a commercial activity involving the transfrontier shipments of hazardous wastes, intended to be managed at economically attractive waste-handling facilities located elsewhere. In fact, huge quantities of hazardous wastes apparently travel the world in search of “acceptable” waste management facilities. For instance, within the industrialized countries alone, millions of tonnes of potentially hazardous waste cross national frontiers each year on their way for recycling or to treatment, storage, and disposal facilities (TSDFs) because there is no local disposal capacity for these wastes, or because legal disposal or reuse in a foreign country may be more environmentally sound, or managing the wastes in the foreign country may be less expensive than at home. The cross-boundary traffic in hazardous wastes has lately been under close public scrutiny, however, resulting in the accession of several international agreements and laws to regulate such activities. This paper discusses and analyzes the most significant control measures and major agreements in this new commercial activity involving hazardous wastes. In particular, the discussion recognizes the difficulties with trying to implement the relevant international agreements among countries of vastly different socioeconomic backgrounds. Nonetheless, it is also noted that global environmental agreements will generally be a necessary component of ensuring adequate environmental protection for the world community—and thus a need for the careful implementation of such agreements and regulations.     

基于物联网的杭州市危险废物智能监管平台设计与应用

为满足危险废物监管各种业务管理工作的需求,开展物联网技术在危险废物产生、转移、处置等过程中应用的研究,设计基于物联网技术的危险废物智能监管平台,建成由管理部门门户、产废单位门户、运输单位门户、处置单位门户等四大门户统领,危废监督管理系统、电子联单系统、GIS监控管理系统、污泥刷卡转运管理系统、危废视频监控系统、固废超市管理系统等六大系统组建的统一管理平台,在传统管理模式的基础上,以业务需求结合先进的物联网、移动互联、二维码、NFC、GPS等技术,创新性地形成"移动端电子联单模式、GPRS监管预警模式、IC卡刷卡转运模式、固废超市微循环管理模式"四大管理模式,实现涉危单位内部微循环管理,转运过程多手段监控,让危险废物从最初产生到最终处置的全过程业务流程呈现精细化、实时化的全闭环管理,实现对危险废物从"摇篮"到"坟墓"的全过程跟踪,并以此为基础建立一支业务处理迅速、信息统计分析及时、办事高效、危废监管全面的信息化管理队伍,为环保部门真实、细致、及时、动态地掌握危险废物的转移情况提供技术手段,为领导决策提供辅助支持。     

Utilization of municipal solid waste (MSW) ash in cement and mortar

Solid waste management is gaining significant importance with the ever-increasing quantities of waste materials generated these days. With increased environmental awareness and its potential hazardous effects, recycling/utilization of these materials have become an attractive alternative to disposal. Some of these waste and hazardous materials could possible be used in cement-based materials. One of such waste is municipal solid waste. Ash is obtained after incineration of MSW.This paper presents comprehensive details of the physical, chemical, and mineralogical composition, elemental analysis of ash obtained from MSW. It also covers the effect of MSW ash on the hydration characteristics, setting times, compressive strength, sulfate resistance and mass loss of cement and mortar. It also deals with the leachate analysis of MSW ash.     

Air quality assessment for land disposal of industrial wastes

Air pollution from hazardous waste landfills and lagoons is largely unknown. Routine monitoring of toxic air contaminants associated with hazardous waste facilities is difficult and very costly. The method presented in this paper would be useful for air quality assessment in the absence of monitoring data. It may be used as a screening process to examine the question of whether or not volatilization is considered to be significant for a given contaminant and also to evaluate permit applications for new hazardous waste facilities concerning waste volatilization problems.     

四川省危险废物管理现状分析及评价

随着城市化进程的加快,危险废物的产生量快速增加,数量多、分布广、危害大、潜在利用价值高,管理处理难度大,因此带来了巨大的环境安全隐患。本文利用相关调查统计数据,分析了四川省危险废物产生特性及污染特性,指出危险废物管理过程中出现的问题已成为阻碍四川省循环经济发展及生态省建设的壁垒,针对出现的问题,提出了相关对策和建议。     

A life cycle based multi-objective optimization model for the management of computer waste

The accelerating pace of waste generation from used electrical and electronic equipment is of growing global concern. Within this waste stream, computer hardware is quite significant in terms of both volume and risk to the environment because of the hazardous materials within it. The waste management hierarchy of prevention, reuse, recycle, treatment and disposal in landfill is accepted as a universal guideline for waste management. The contemporary concept of integrated solid waste management is very complex comprising of not only the environmental aspects or the technical aspects of the waste management hierarchy, but also incorporating economic, institutional, perceived risk and social issues in the context of complete life cycle of waste. Moreover, when to shift from one stage of hierarchy to another, is an involved decision warranting inclusion of several case specific issues. This paper presents a life cycle based multi-objective model that can help decision makers in integrated waste management. The proposed model has been applied to a case study of computer waste scenario in Delhi, India, which apart from having computer waste from its native population receives large quantities of imported second hand computers. The model has been used to evaluate management cost and reuse time span or life cycle of various streams of computer waste for different objectives of economy, perceived risk and environmental impact. The model results for different scenarios of waste generation have been analyzed to understand the tradeoffs between cost, perceived risk and environmental impact. The optimum life cycle of a computer desktop was observed to be shorter by 25% while optimizing cost than while optimizing impact to the environment or risk perceived by public. Proposed integrated approach can be useful for determining the optimum life cycle of computer waste, as well as optimum configuration of waste management facilities, for urban centers where computer waste related issues are of growing concern.     

A life cycle based multi-objective optimization model for the management of computer waste

The accelerating pace of waste generation from used electrical and electronic equipment is of growing global concern. Within this waste stream, computer hardware is quite significant in terms of both volume and risk to the environment because of the hazardous materials within it. The waste management hierarchy of prevention, reuse, recycle, treatment and disposal in landfill is accepted as a universal guideline for waste management. The contemporary concept of integrated solid waste management is very complex comprising of not only the environmental aspects or the technical aspects of the waste management hierarchy, but also incorporating economic, institutional, perceived risk and social issues in the context of complete life cycle of waste. Moreover, when to shift from one stage of hierarchy to another, is an involved decision warranting inclusion of several case specific issues. This paper presents a life cycle based multi-objective model that can help decision makers in integrated waste management. The proposed model has been applied to a case study of computer waste scenario in Delhi, India, which apart from having computer waste from its native population receives large quantities of imported second hand computers. The model has been used to evaluate management cost and reuse time span or life cycle of various streams of computer waste for different objectives of economy, perceived risk and environmental impact. The model results for different scenarios of waste generation have been analyzed to understand the tradeoffs between cost, perceived risk and environmental impact. The optimum life cycle of a computer desktop was observed to be shorter by 25% while optimizing cost than while optimizing impact to the environment or risk perceived by public. Proposed integrated approach can be useful for determining the optimum life cycle of computer waste, as well as optimum configuration of waste management facilities, for urban centers where computer waste related issues are of growing concern.     

Waste in the Inner City: Asset or assault?

In an unequal society, undesirable wastes often end up in the poorest and least powerful communities, becoming part of the economic and environmental milieu of the inner city. Two contradictory responses to waste reflect contrasting theoretical paradigms. Some wastes can become assets in local economic development, creating incomes through scavenging, industrial jobs in recycling plants or new businesses using locally available materials. Other wastes are an assault on the community that receives them; toxic wastes, polluting facilities and industrial by-products often create local health hazards rather than development. Waste as an asset is consistent with the free market model of economics. The inner city, 'endowed' with waste materials and low-wage labour, has a comparative advantage in labour-intensive processing of materials that the rest of society has discarded. Waste as an assault on the community is consistent with a different model of environmental risk. Some by-products of industry are so hazardous that they should not be produced, or should be tightly regulated. Each model has a realm of validity; the balance between the two depends on which wastes are hazardous, and which are just ugly resources waiting to be discovered.     

发达国家和地区危险废物名录管理实践

危险废物名录制度是危险废物环境管理的基础。2016年6月14日,环境保护部、国家发改委、公安部联合公布了《国家危险废物名录》(2016年版),对2008年版危险废物名录进行了调整。本文介绍了主要发达国家和地区危险废物名录制度的基本情况,对其优缺点进行了对比分析,以期为更好的理解新版危险废物名录提供参考。主要发达国家和地区的危险废物名录管理体系具有以下优点:一是完善的危险废物豁免排除制度加强了企业和管理部门的责任意识。二是危险废物和一般固体废物共享分类体系便于对废物的统筹管理,废物代码内容翔实,增加了名录的可操作性。三是基于不同处理责任主体进行分类,避免了名录方式或列举方式造成的"漏分"现象。四是根据环境风险实行分级管理,重点突出。同时存在几点不足:一是鉴别程序繁琐,降低了危险废物处置效率;二是存在部分行业产生的废物遗漏、同类危险废物分类过细等问题;三是部分国家危险废物分类过于笼统,不利于企业对危险废物种类及属性的识别。     

Sydney tar ponds: some problems in quantifying toxic waste

Information on the type and amount of hazardous and toxic waste is required to develop a meaningful strategy and estimate a realistic cost for clean up of the Sydney Tar Pond site which is located on Cape Breton, in the province of Nova Scotia, Canada. The site covers the area of the decommissioned Sysco (Sydney Steel Corporation) plant. The materials of concern include BTEX (benzene, toluene, ethylbenzene, and xylenes), PAH (polycyclic aromatic hydrocarbons), PCB (polychlorinated biphenyl), and particulates laden with toxic metals, such as arsenic, lead, and others. The originally nontoxic materials such as soil, blast furnace slag, and vegetation, as well as surface and ground waters, which were subsequently contaminated, must also be included if they fail tests prescribed by environmental regulations. An extensive sampling program must be undertaken to obtain data for an accurate estimate of the waste to be cleaned and disposed of. Apparently, 700,000 tons of toxic waste, which is believed to be present on the site, may represent only a fraction of the actual amount. The clean-up of the site is only part of the solution. Toxic waste has to be disposed of in accordance with environmental regulations.     

Future solutions for the treatment and disposal of hazardous wastes in China

The current status of the treatment and disposal of hazardous wastes in China is summarized on the basis of the results of the Declaring and Registration Project initiated nationally in 1995. A principle framework for the sound management of hazardous wastes is proposed, which includes three levels of technical solutions. Large-scale enterprises are encouraged to recycle, to treat, and to dispose of wastes by means of constructing facilities, and to have their extra capacities available to the public for a reasonable fee. Municipal governments, provincial governments, and the Central Government are to plan and construct centralized facilities to recycle, treat, and dispose of wastes. For a solution at the manufacturing level, recycling is identified as the main approach. Centralized facilities at the municipal level will mainly focus on special wastes that are unsuitable to transport and store, such as hospital waste, and for the technical solution at this level, incineration and recycling are identified as the main approaches. For the technical solution at the provincial and national levels, landfill and incineration are identified as the main approaches. Based on this principle and the current available data on hazardous wastes, a preliminary plan for the spatial distribution of cross-provincial centralized treatment and disposal facilities of hazardous wastes is presented. The construction of approximately nine cross-provincial comprehensive facilities is proposed. A priority list for the construction of these planned facilities is also presented.     

The management and utilization of Scottish wildlife sites

This paper identifies criteria for efficient public utilization of designated wildlife sites. It describes a survey of the major wildlife sites in Scotland in order to determine the site management objectives and extent to which sites are utilized by visitors. Substantial differences were found to exist between organizations as regards site management objectives, promotion and the provision of visitor facilities. Explanations for the apparent variability in efficiency of site utilization are discussed in terms of organization ideology, funding and structure. It is argued that trusts funded through membership may be best able to reconcile the benefits from current site utilization with the conservation of long‐term use and existence values.     

An Expert System for Waste Management

Management of hazardous waste is an increasing problem for both the companies that generate the waste and for the communities that eventually experience the consequences of the management decisions. Thus, both social and political aspects must be considered when solving these problems. It is thus important that waste management technologies are evaluated by a panel of experts with various backgrounds. The methodology for developing an expert system for waste treatment technology evaluation was discussed. An expert system was developed to select the “best” waste treatment alternatives. This expert system includes two different knowledge bases: one for the economic and technical parts of the problem and another for the social and political aspects. This expert system was developed on an IBM personal computer using Turbo Prolog™. The pulp and paper industry was selected as an example problem for developing this expert system, which system was tested using two example waste streams from the pulp and paper industry. The results agree with the current treatment facilities the companies are using.