Vegetative Buffer Strips for Reducing Herbicide Transport in Runoff: Effects of Buffer Width,Vegetation, and Season

The effectiveness of vegetative buffer strips (VBS) for reducing herbicide transport has not been well documented for runoff prone soils. A multi‐year plot‐scale study was conducted on an eroded claypan soil with the following objectives: (1) assess the effects of buffer width, vegetation, and season on runoff transport of atrazine (ATR), metolachlor (MET), and glyphosate; (2) develop VBS design criteria for herbicides; and (3) compare differences in soil quality among vegetation treatments. Rainfall simulation was used to create uniform antecedent soil water content and to generate runoff. Vegetation treatment and buffer width impacted herbicide loads much more than season. Grass treatments reduced herbicide loads by 19‐28% and sediment loads by 67% compared to the control. Grass treatments increased retention of dissolved‐phase herbicides by both infiltration and adsorption, but adsorption accounted for the greatest proportion of retained herbicide load. This latter finding indicated VBS can be effective on poorly drained soils or when the source to buffer area ratio is high. Grass treatments modestly improved surface soil quality 8‐13 years after establishment, with significant increases in organic C, total N, and ATR and MET sorption compared to continuously tilled control. Herbicide loads as a function of buffer width were well described by first‐order decay models which indicated VBS can provide significant load reductions under anticipated field conditions.     

Alachlor and bentazone losses from subsurface drainage of two soils

Atrazine (6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4-diamine) is frequently detected at high concentrations in ground water. Bentazone [3-isopropyl-1H-2,1,3-benzothiadiazin-4(3H)-one 2,2-dioxide] plus alachlor (2-chloro-2',6'-diethyl-N-methoxymethylacetanilide) is a potential herbicide combination used as a substitute for atrazine. Thus, the objective of this study was to assess the environmental risk of this blend. Drainage water contamination by bentazone and alachlor was assessed in silty clay (Vertic Eutrochrept) and silt loam (Aquic Hapludalf) soils under the same management and climatic conditions. Drainage volumes and concentrations of alachlor and bentazone were monitored after application. Herbicides first arrived at the drains after less than 1 cm of net drainage. This is consistent with preferential flow and suggests that about 3% of the pore volume was active in rapid transport. During the monitoring periods, bentazone losses were higher (0.11-2.40% of the applied amount) than alachlor losses (0.00-0.28%) in the drains of the silty clay and silt loam. The rank order of herbicide mass losses corresponded with the rank order of herbicide adsorption coefficients. More herbicide residues were detected in drainage from the silty clay, probably due to preferential flow and more intensive drainage in this soil than the silt loam. Surprisingly, herbicide losses were higher in the drains of both soils in the drier of the two study years. This could be explained by the time intervals between the treatments and first drainage events, which were longer in the wetter year. Results suggest that the drainage phases occurred by preferential flow in the spring-summer period, with correspondingly fast leaching of herbicides, and by matrix flow during the fall-winter period, with slower herbicide migration.     

Tillage system, application rate, and extreme event effects on herbicide losses in surface runoff

Conservation tillage can reduce soil loss; however, the residual herbicides normally used to control weeds are often detected in surface runoff at high levels, particularly if runoff-producing storms occur shortly after application. Therefore, we measured losses of alachlor, atrazine, linuron, and metribuzin from seven small (0.45-0.79-ha) watersheds for 9 yr (1993-2001) to investigate whether a reduced-input system for corn (Zea mays L.) and soybean [Glycine max (L.) Merr.] production with light disking, cultivation, and half-rate herbicide applications could reduce losses compared with chisel and no-till. As a percentage of application, annual losses were highest for all herbicides for no-till and similar for chisel and reduced-input. Atrazine was the most frequently detected herbicide and yearly flow-weighted concentrations exceeded the drinking water standard of 3 microg L(-1) in 20 out of 27 watershed years that it was applied. Averaged for 9 corn yr, yearly flow-weighted atrazine concentrations were 26.3, 9.6, and 8.3 microg L(-1) for no-till, chisel, and reduced-input, respectively. Similarly, flow-weighted concentrations of alachlor exceeded the drinking water standard of 2 microg L(-1) in 23 out of 54 application years and in all treatments. Thus, while banding and half-rate applications as part of a reduced-input management practice reduced herbicide loss, concentrations of some herbicides may still be a concern. For all watersheds, 60 to 99% of herbicide loss was due to the five largest transport events during the 9-yr period. Thus, regardless of tillage practice, a small number of runoff events, usually shortly after herbicide application, dominated herbicide transport.     

Residual and contact herbicide transport through field lysimeters via preferential flow

Usage of glyphosate [N-(phosphonomethyl)-glycine] and glufosinate [2-amino-4-(hydroxy-methylphosphinyl)butanoic acid] may reduce the environmental impact of agriculture because they are more strongly sorbed to soil and may be less toxic than many of the residual herbicides they replace. Preferential flow complicates the picture, because due to this process, even strongly sorbed chemicals can move quickly to ground water. Therefore, four monolith lysimeters (8.1 m(2) by 2.4 m deep) were used to investigate leaching of contact and residual herbicides under a worst-case scenario. Glufosinate, atrazine (6-chloro-N(2)-ethyl-N(4)-isopropyl-1,3,5-triazine-2,4-diamine), alachlor [2-chloro-N-(2,6-diethylphenyl)-N-(methoxymethyl) acetamide], and linuron (3-3,4-dichlorophenyl-1-methoxy-1-methylurea) were applied in 1999 before corn (Zea mays L.) planting and glyphosate, alachlor, and metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one] were applied in 2000 before soybean [Glycine max (L.) Merr.] planting. A high-intensity rainfall was applied shortly after herbicide application both years. Most alachlor, metribuzin, atrazine, and linuron losses occurred within 1.1 d of rainfall initiation and the peak concentration of the herbicides coincided (within 0.1 d of rainfall initiation in 2000). More of the applied metribuzin leached compared with alachlor during the first 1.1 d after rainfall initiation (2.2% vs. 0.035%, P < 0.05). In 1999, 10 of 24 discrete samples contained atrazine above the maximum contaminant level (atrazine maximum contaminant level [MCL] = 3 mug L(-1)) while only one discrete sample contained glufosinate (19 mug L(-1), estimated MCL = 150 mug L(-1)). The results indicate that because of preferential flow, the breakthrough time of herbicides was independent of their sorptive properties but the transport amount was dependent on the herbicide properties. Even with preferential flow, glyphosate and glufosinate were not transported to 2.4 m at concentrations approaching environmental concern.     

Preferential bromide and pesticide movement to tile drains under different cropping practices

Subsurface drainage systems are useful tools to study chemical leaching in soils. Our objective was to compare the breakthrough behavior of bromide, atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine) and metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-methoxy-1-methylethyl) acetamid] to tile drains under two fall tillage practices (conventional tillage [CT] with a moldboard plow, and reduced tillage [RT] with a chisel plow) in field plots cultivated with corn (Zea mays L.). Leachate volume were greater in RT than in CT, with no statistical differences. Soil analysis showed that bromide migrated deeper in the soil profile than both herbicides, with little tillage effect. All chemicals were detected in drainage water at the same time and followed an event-driven behavior. Tillage had no effect on atrazine and metolachlor found in drainage water, while bromide concentration peaks were higher in RT than in CT in 1999. Concentration peaks were recorded earlier for atrazine and metolachlor than for bromide. Plots of cumulative relative chemical mass (cumulative mass divided by total mass measured in drainage) as a function of cumulative drainage were mostly linear for bromide, while they were S-shaped for both herbicides. Drainage that corresponded to 50% of relative cumulative mass ranged from 40 to 55% for bromide and from 5 to 28% for both herbicides. Rapid chemical movement to tile drains suggested that preferential flow was important in both CT and RT, and that these tillage practices had little influence on this phenomena.     

Reducing herbicides and veterinary antibiotics losses from agroecosystems using vegetative buffers

Multiple species vegetative buffer strips (VBSs) have been recommended as a cost-effective approach to mitigate agrochemical transport in surface runoff derived from agronomic operations, while at the same time offering a broader range of long-term ecological and environmental benefits. However, the effect of VBS designs and species composition on reducing herbicide and veterinary antibiotic transport has not been well documented. An experiment consisting of three VBS designs and one continuous cultivated fallow control replicated in triplicate was conducted to assess effectiveness in reducing herbicide and antibiotic transport for claypan soils. The three VBS designs include (i) tall fescue, (ii) tall fescue with a switchgrass hedge barrier, and (iii) native vegetation (largely eastern gamagrass). Rainfall simulation was used to create uniform antecedent soil moisture content in the plots and to generate runoff. Our results suggested that all VBS significantly reduced the transport of dissolved and sediment-bound atrazine, metolachlor, and glyphosate in surface runoff by 58 to 72%. Four to 8 m of any tested VBS reduced dissolved sulfamethazine transport in the surface runoff by more than 70%. The tall fescue VBS was overall most effective at reducing dissolved tylosin and enrofloxacin transport in the runoff (>75%). The developed exponential regression models can be used to predict expected field-scale results and provide design criteria for effective field implementation of grass buffers. Our study has demonstrated that an optimized VBS design may achieve desired agrochemical reductions and minimize acreage removed from crop production.     

Impact of glyphosate-tolerant soybean and glufosinate-tolerant corn production on herbicide losses in surface runoff

Residual herbicides used in the production of soybean [Glycine max (L.) Merr] and corn (Zea mays L.) are often detected in surface runoff at concentrations exceeding their maximum contaminant levels (MCL) or health advisory levels (HAL). With the advent of transgenic, glyphosate-tolerant soybean and glufosinate-tolerant corn this concern might be reduced by replacing some of the residual herbicides with short half-life, strongly sorbed, contact herbicides. We applied both herbicide types to two chiseled and two no-till watersheds in a 2-yr corn-soybean rotation and at half rates to three disked watersheds in a 3-yr corn/soybean/wheat (Triticum aestivum L.)-red clover (Trifolium pratense L.) rotation and monitored herbicide losses in runoff water for four crop years. In soybean years, average glyphosate loss (0.07%) was approximately 1/7 that of metribuzin (0.48%) and about one-half that of alachlor (0.12%), residual herbicides it can replace. Maximum, annual, flow-weighted concentration of glyphosate (9.2 microg L(-1)) was well below its 700 microg L(-1) MCL and metribuzin (9.5 microg L(-1)) was well below its 200 microg L(-1) HAL, whereas alachlor (44.5 microg L(-1)) was well above its 2 microg L(-1) MCL. In corn years, average glufosinate loss (0.10%) was similar to losses of alachlor (0.07%) and linuron (0.15%), but about one-fourth that of atrazine (0.37%). Maximum, annual, flow-weighted concentration of glufosinate (no MCL) was 3.5 microg L(-1), whereas atrazine (31.5 microg L(-1)) and alachlor (9.8 microg L(-1)) substantially exceeded their MCLs of 3 and 2 microg L(-1), respectively. Regardless of tillage system, flow-weighted atrazine and alachlor concentrations exceeded their MCLs in at least one crop year. Replacing these herbicides with glyphosate and glufosinate can reduce the occurrence of dissolved herbicide concentrations in runoff exceeding drinking water standards.     

Impact of climatic and soil conditions on environmental fate of atrazine used under plantation forestry in Australia

We studied the leaching and dissipation of atrazine (2-chloro-4-ethylamino-6-isopropylamino-1, 3, 5-s-triazine) and its two principal metabolites (desethylatrazine and desisopropylatrazine) for more than two years through soil profiles at five forestry sites across Australia (representing subtropical, temperate and Mediterranean climatic conditions with rainfall ranging from 780 to 1536 mm yr^?1). Following atrazine applications at local label rates, soil cores were collected at regular intervals (up to depths of 90–150 cm), and the residues of the three compounds in soil were analysed in composite samples using liquid chromatography. Bromide was applied simultaneously with atrazine to follow the movement of the soil water. While bromide ion rapidly leached through the entire profile, in most cases the bulk of atrazine, desethylatrazine and desisopropylatrazine remained in the top 45 cm of the soil profile. However, a small fraction of residue moved deeper into the soil profile and at a subtropical site (Toolara) trace levels (ng L^?1) of atrazine and one of its metabolites (DEA) were detected in perched groundwater located at a depth of 1.8 m. Data on the total residues of atrazine in soil profiles from all sites except the Tasmanian site fitted a first-order decay model. The half-life of atrazine in surface soils at the subtropical sites (Toolara and Imbil) ranged from 11 to 21 days. Four separate applications of atrazine at Toolara resulted in a narrow range of half-lives (16 ± 3.6 days), confirming relatively rapid dissipation of atrazine under subtropical conditions (Queensland). In contrast, a prominent biphasic pattern of initial rapid loss followed by very slow phase of degradation of atrazine was observed under the colder temperate climate of Highclere (Tasmania). The data showed that while its 50% (DT₅₀) loss occurred relatively rapidly (36 days), more than 10% of herbicide residue was still detectable in the profile even a year after application (DT₉₀ = 375 days). The rate of dissipation of atrazine at warm subtropical Queensland sites (Imbil and Toolara) was 2–3 times faster than sites located in colder climate of Tasmania. The marked contrast in DT₅₀ values between subtropical and temperate sites suggest that climatic conditions (soil temperature) is one of the key factors affecting atrazine dissipation. At the Tasmanian site, the combination of leaching of the herbicide in subsoil and slower microbial activity at cooler temperatures would have caused a longer persistence of atrazine.     

Behavior of pesticide residues in agricultural soil and adjacent River Kuywa sediment and water samples from Nzoia sugarcane belt in Kenya

An inventory survey conducted to determine pesticide usage in a sub-catchment of the Nzoia sugarcane belt found a variety of pesticides used in the sub-catchment, which are reported in this paper. Analysis of soil samples from seven fallow experimental field plots left uncultivated for various periods from 3 to 96?months after cultivation with pesticide application indicated persistence of high concentrations of pesticide residues in the soil, with estimated soil half-lives (in years) ranging from 0.72 to 57.75 for organochlorines and from 1.13 to 8.25 for herbicides. The mean water concentrations (in ??g/L) of the pesticide residues in River Kuywa, which flows through the Nzoia Nucleus Estate sugarcane farms, ranged from 0.12 (lindane) to 1.36 (p,p??-DDT) for organochlorines and from 0.14 (atrazine) to 1.75 (diuron) for herbicides during the heavy rains period in August 2008 while the mean sediment concentrations (in ??g/g) ranged from 0.28 (lindane) to 1.87 (endrin) for organochlorines and 0.39 (hexazinone) to 4.61 (alachlor) for herbicides. The mean concentrations of residues in water during the light rain period in December 2008 ranged from 0.17 (p,p??-DDT) to 0.71 (aldrin) for organochlorines and 0.01 (atrazine) to 1.74 (alachlor) for herbicides while the sediment concentrations ranged from 0.38 (p,p??-DDT) to 1.145 (aldrin) for organochlorines and 0.74 (atrazine) to 1.98 (alachlor) for herbicides. Although DDT, aldrin, dieldrin, and endrin were not reported in the survey, their presence in the fallow experimental field plot soils and in River Kuywa water and sediment could indicate previous application, lack of recorded data or illegal usage since 1997 when they were banned. Notably, the concentrations of alachlor, diuron, cypermethrin, and hexazinone in the water column were substantial indicating their extensive usage and residual persistence in the sub-catchment, with subsequent wash-off and leaching into River Kuywa. The concentration levels of some of the individual pesticides exceeded the EU limit requirements for drinking water and indicated potential risk to humans and cattle if the water is used without treatment.     

Comparative losses of glyphosate and selected residual herbicides in surface runoff from conservation-tilled watersheds planted with corn or soybean

Residual herbicides regularly used in conjunction with conservation tillage to produce corn ( L.) and soybean [ (L.) Merr] are often detected in surface water at concentrations that exceed their U.S. maximum contaminant levels (MCL) and ecological standards. These risks might be reduced by planting glyphosate-tolerant varieties of these crops and totally or partially replacing the residual herbicides alachlor, atrazine, linuron, and metribuzin with glyphosate, a contact herbicide that has a short half-life and is strongly sorbed to soil. Therefore, we applied both herbicide types at typical rates and times to two chisel-plowed and two no-till watersheds in a 2-yr corn/soybean rotation and at half rates to three disked watersheds in a 3-yr corn/soybean/wheat-red clover ( L.- L.) rotation and monitored herbicide losses in surface runoff for three crop years. Average dissolved glyphosate loss for all tillage practices, as a percentage of the amount applied, was significantly less ( ≤ 0.05) than the losses of atrazine (21.4x), alachlor (3.5x), and linuron (8.7x) in corn-crop years. Annual, flow-weighted, concentration of atrazine was as high as 41.3 μg L, much greater than its 3 μg L MCL. Likewise, annual, flow-weighted alachlor concentration (MCL = 2 μg L) was as high as 11.2 and 4.9 μg L in corn- and soybean-crop years, respectively. In only one runoff event during the 18 watershed-years it was applied did glyphosate concentration exceed its 700 μg L MCL and the highest, annual, flow-weighted concentration was 3.9 μg L. Planting glyphosate-tolerant corn and soybean and using glyphosate in lieu of some residual herbicides should reduce the impact of the production of these crops on surface water quality.     

Retention and runoff losses of atrazine and metribuzin in soil

Minimizing herbicide runoff and mobility in the soil and thus potential contamination of water resources is a national concern. Metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one] and atrazine [2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine] dynamics in surface soils and in runoff waters were studied on six 0.2-ha sugarcane (Saccharum spp.) plots of a Commerce silt loam (fine-silty, mixed, superactive, nonacid, thermic Fluvaquentic Endoaquept) during three growing seasons under different best management practices. Metribuzin was applied in the spring as a postemergence herbicide and atrazine was applied following winter harvest. Both herbicides were applied on top of the sugarcane rows as 0.6- or 0.9-m band width application, or broadcast application, where the entire area was treated. Maximum effluent concentrations were measured from the broadcast treatment and ranged from 600 to 1100 microg L(-1) for atrazine and 250 to 450 microg L(-1) for metribuzin. Atrazine runoff losses were highest for the broadcast treatment (2.8-11% of that applied) and lowest for the 0.6-m band treatment (1.9-7.6%), with a similar trend for metribuzin losses. Measured extractable herbicides from the surface soil exhibited a sharp decrease with time and were well described with a simple first-order decay model. For atrazine, estimates for the decay rate (lambda) were higher than for metribuzin. Results based on laboratory adsorption-desorption (kinetic-batch) measurements were consistent with field observations. The distribution coefficients (Kd) for atrazine exhibited stronger retention over time in comparison with metribuzin on the Commerce soil. Moreover, discrepancies between adsorption isotherm and desorption indicated slower release and that hysteresis was more pronounced for atrazine compared with metribuzin.     

Major herbicides in ground water: results from the National Water-Quality Assessment

To improve understanding of the factors affecting pesticide occurrence in ground water, patterns of detection were examined for selected herbicides, based primarily on results from the National Water-Quality Assessment (NAWQA) program. The NAWQA data were derived from 2,227 sites (wells and springs) sampled in 20 major hydrologic basins across the USA from 1993 to 1995. Results are presented for six high-use herbicides--atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine), cyanazine (2-[4-chloro-6-ethylamino-1,3,5triazin-2-yl]amino]-2-methylpropionitrile), simazine (2-chloro-4,6-bis-[ethylamino]-s-triazine), alachlor (2-chloro-N-[2,6-diethylphenyl]-N-[methoxymethyl]acetamide), acetochlor (2-chloro-N-[ethoxymethyl]-N-[2-ethyl-6-methylphenyl]acetamide), and metolachlor (2-chloro-N-[2-ethyl-6-methylphenyl]-N-[2-methoxylethyl]acetamide)--as well as for prometon (2,4-bis[isopropylamino]-6-methoxy-s-triazine), a nonagricultural herbicide detected frequently during the study. Concentrations were <1 microg L(-1) at 98% of the sites with detections, but exceeded drinking-water criteria (for atrazine) at two sites. In urban areas, frequencies of detection (at or above 0.01 microg L(-1)) of atrazine, cyanazine, simazine, alachlor, and metolachlor in shallow ground water were positively correlated with their nonagricultural use nationwide (P < 0.05). Among different agricultural areas, frequencies of detection were positively correlated with nearby agricultural use for atrazine, cyanazine, alachlor, and metolachlor, but not simazine. Multivariate analysis demonstrated that for these five herbicides, frequencies of detection beneath agricultural areas were positively correlated with their agricultural use and persistence in aerobic soil. Acetochlor, an agricultural herbicide first registered in 1994 for use in the USA, was detected in shallow ground water by 1995, consistent with previous field-scale studies indicating that some pesticides may be detected in ground water within 1 yr following application. The NAWQA results agreed closely with those from other multistate studies with similar designs.     

Anionic polyacrylamide effects on soil sorption and desorption of metolachlor,atrazine, 2,4-D,and picloram

Polyacrylamide (PAM) treatment of irrigation water is a growing conservation technology in irrigated agriculture in recent years. There is a concern regarding the environmental impact of PAM after its application. The effects of anionic PAM on the sorption characteristics of four widely used herbicides (metolachlor, atrazine, 2,4-D, and picloram) on two natural soils were assessed in batch equilibrium experiments. Results showed that PAM treatment kinetically reduced the sorption rate of all herbicides, possibly due to the slower diffusion of herbicide molecules into interior sorption sites of soil particles that were covered and/or cemented together by PAM. The equilibrium sorption and desorption amounts of nonionic herbicides (metolachlor and atrazine) were essentially unaffected by anionic PAM, even under a high PAM application rate, while the sorption amounts of anionic herbicides (2,4-D and picloram) were slightly decreased and their desorption amounts increased little. The impact mechanisms of PAM were related to the molecular characteristics of PAM and herbicides. The negative effects of PAM on the sorption of anionic herbicides are possibly caused by the enhancement of electrostatic repulsion by presorbed anionic PAM and competition for sorption sites. However, steric hindrance of the large PAM molecule weakens its influence on herbicide sorption on interior sorption sites of soil particles, which probably leads to the small interference on herbicide sorption, even under high application rates.     

PERCOLATE WATER AND BROMIDE MOVEMENT IN THE ROOT ZONE OF EFFLUENT IRRIGATION SITES1

ABSTRACT: A bromide tracer was used to evaluate percolate water and ion movement in the upper 1.2 m of soil at a proposed sewage effluent irrigation site located in the Missouri Ozarks. Two plots representing Doniphan silt loam and Crider silt loam soils were sprinkler irrigated with local ground water at a rate of 7.62 cm/week from June through August 1976. Soil water potential, percent soil moisture by volume, and background levels of bromide in soil water, ground water, and precipitation were measured at the study plots. Bromide exchange properties and saturated hydraulic conductivity of the soils were determined in the laboratory. During two selected time periods, irrigation water, was spiked with NaBr (5.0 mg/l Br). Bromide movement through the upper profile was quantified by soil water samples and post-sampling neutron activation analysis. Soil moisture was near saturatin in both soils when the Br tracer was applied. Bromide concentrations above background levels (0.023 mg/l Br, Doniphan silt loam and 0.016 mg/l Br, Crider silt loam) were detected within 2.60 hours at 0.9 m in the Doniphan soil and within 3.75 hours at that depth in the Crider soil. The rate of Br movement in the profile was greater in both soils than the measured saturated hydraulic conductivity, Bromide concentrations above background levels were present in soil water from the study plots for a minimum of 21 days after irrigation with the Br tracer.     

SUSCEPTIBILITY OF INDIANA WATERSHEDS TO HERBICIDE CONTAMINATION1

ABSTRACT: An index of watershed susceptibility to surface water contamination by herbicides could be used to improve source water assessments for public drinking water supplies, prioritize watershed restoration projects, and direct funding and educational efforts to areas where the greatest environmental benefit can be realized. The goal of this study is to use streamflow and herbicide concentration data to develop and evaluate a method for estimating comparative watershed susceptibility to herbicide loss. United States Geological Survey (USGS) concentration data for five relatively water soluble herbicides (alachlor, atrazine, cyanazine, metolachlor, and simazine) were analyzed for 16 Indiana watersheds. Correlation was assessed between observed herbicide losses and: (1) a herbicide runoff index using GIS‐based land use, soil type, SCS runoff curve number, tillage practice, herbicide use estimates, and combinations of these factors; and (2) predicted herbicide losses from a non‐point source pollution model (NAPRA‐Web, an Internet‐based interface for GLEAMS). The highest adjusted R²value was found between herbicide concentration and the runoff curve number alone, ranging from 0.25 to 0.56. Predictions from the simulation model showed a poorer correlation with observed herbicide loss. This indicates potential for using the runoff curve number as a simple herbicide contamination susceptibility index.     

FACTORS AFFECTING HERBICIDE YIELDS IN THE CHESAPEAKE BAY WATERSHED,JUNE 19941

ABSTRACT: Median concentrations and instantaneous yields of alachlor, metolachlor, atrazine, cyanazine, and simazine were generally highest at sites in the Lower Susquehanna River Basin and in agricultural subbasins. Instantaneous herbicide yields are related to land use, hydrogeologic setting, streamflow yield, and agricultural row cropping practices. The significance of these relations may be affected by the interdependence of the factors. The percentage of basin area planted in corn is the most influential factor in the prediction of herbicide yield. Instantaneous yields of all five herbicides measured in June 1994 related poorly to averaged 1990–94 herbicide use. Annually averaged herbicide-use data are too general to use as a predictor for short-term herbicide yields. An evaluation of factors affecting herbicide yields could be refined with more-current land use and land cover information and a more accurate estimate of the percentage of basin area planted in corn. Factors related to herbicide yields can be used to predict herbicide yields in other basins within the Chesapeake Bay watershed and to develop an estimate of herbicide loads to Chesapeake Bay.     

Assessment of herbicide leaching risk in two tropical soils of Reunion Island (France)

Application of organic chemicals to a newly irrigated sugarcane (Saccharum officinarum L.) area located in the semiarid western part of Reunion Island has prompted local regulatory agencies to determine their potential to contaminate ground water resources. For that purpose, simple indices known as the ground water ubiquity score (Gustafson index, GUS), the retardation factor (RF), the attenuation factor (AF), and the log-transformed attenuation factor (AFT) were employed to assess the potential leaching of five herbicides in two soil types. The herbicides were alachlor [2-chloro-2',6'-diethyl-N-(methoxy-methy) acetanilide], atrazine [2-chloro-4-(ethylamino)-6-(isopropylamino)-1,3,5-triazine], diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea], 2,4-D [(2,4-dichlorophenoxy) acetic-acid], and triclopyr [((3,5,6-trichloro-2-pyridyl)oxy) acetic-acid]. The soil types were Vertic (BV) and Andepts (BA) Inceptisols, which are present throughout the Saint-Gilles study area on Reunion Island. To calculate the indices, herbicide sorption (K(oc)) and dissipation (half-life, DT50) properties were determined from controlled batch experiments. Water fluxes below the root zone were estimated by a capacity-based model driven by a rainfall frequency analysis performed on a 13-yr data series. The results show a lower risk of herbicide leaching than in temperate regions due to the tropical conditions of the study area. Higher temperatures and the presence of highly adsorbent soils may explain smaller DT50 and higher K(oc) values than those reported in literature concerning temperate environments. Based on the RF values, only 2,4-D and triclopyr appear mobile in the BV soil, with all the other herbicides being classified from moderately to very immobile in both soils. The AFT values indicate that the potential leaching of the five herbicides can be considered as unlikely, except during the cyclonic period (about 40 d/yr) when there is a 2.5% probability of recharge rates equal to or higher than 50 mm/d. In that case, atrazine in both soils, 2,4-D and triclopyr in the BV soil, and diuron and alachlor in the BA soil present a high risk of potential contamination of ground water resources.     

Small-scale spatial variability of atrazine and dinoseb adsorption parameters in an alluvial soil

Soil sorption processes largely control the environmental fate of herbicides. Therefore, accuracy of sorption parameters is crucial for accurate prediction of herbicide mobility in agricultural soils. A combined experimental and statistical study was performed to investigate the small-scale spatial variability of sorption parameters for atrazine and dinoseb in soils and to establish the number of samples needed to provide a value of the distribution coefficient (K(d)) next to the mean, with a given precision. The study explored sorption properties of the two herbicides in subsurface samples collected from four pits distributed along a transect of an alluvial soil; two to four samples were taken at about 30 cm apart at each sampling location. When considering all the data, the distribution coefficients were found to be normally and log-normally distributed for atrazine and dinoseb, respectively; the CVs were relatively high (close to 50% for dinoseb and 40% for atrazine). When analyzed horizon by horizon, the data revealed distribution coefficients normally distributed for both herbicides, whatever the soil layer, with lower CVs. The K(d) values were shown to vary considerably between samples collected at very short distance (a few centimeters), suggesting that taking a single soil sample to determine sorption properties through batch experiments can lead to highly unrepresentative results and to poor sorption/mobility predictions.     

REGIONAL PATTERNS OF PESTICIDE CONCENTRATIONS IN SURFACE WATERS OF NEW YORK IN 19971

ABSTRACT: The predominant mixtures of pesticides found in New York surface waters consist of five principal components. First, herbicides commonly used on corn (atrazine, metolachlor, alachlor, cyanazine) and a herbicide degradate (deethylatrazine) were positively correlated to a corn‐herbicide component, and watersheds with the highest corn‐herbicide component scores were those in which large amounts of row crops are grown. Second, two insecticides (diazinon and carbaryl) and one herbicide (prometon) widely used in urban and residential settings were positively correlated to an urban/residential component. Watersheds with the highest urban/residential component scores were those with large amounts of urban and residential land use. A third component was related to two herbicides (EPTC and cyanazine) used on dry beans and corn, the fourth to an herbicide (simazine) and an insecticide (carbaryl) commonly used in orchards and vineyards, and the fifth to an herbicide (DCPA). Results of this study indicate that this approach can be used to: (1) identify common mixtures of pesticides in surface waters, (2) relate these mixtures to land use and pesticide applications, and (3) indicate regions where these mixtures of pesticides are commonly found.     

Spatial variability of atrazine and metolachlor dissipation on dryland no-tillage crop fields in Colorado

An area of interest in precision farming is variable-rate application of herbicides to optimize herbicide use efficiency and minimize negative off-site and non-target effects. Site-specific weed management based on field scale management zones derived from soil characteristics known to affect soil-applied herbicide efficacy could alleviate challenges posed by post-emergence precision weed management. Two commonly used soil-applied herbicides in dryland corn (Zea mays L.) production are atrazine and metolachlor. Accelerated dissipation of atrazine has been discovered recently in irrigated corn fields in eastern Colorado. The objectives of this study were (i) to compare the rates of dissipation of atrazine and metolachlor across different soil zones from three dryland no-tillage fields under laboratory incubation conditions and (ii) to determine if rapid dissipation of atrazine and/or metolachlor occurred in dryland soils. Herbicide dissipation was evaluated at time points between 0 and 35 d after soil treatment using a toluene extraction procedure with GC/MS analysis. Differential rates of atrazine and metolachlor dissipation occurred between two soil zones on two of three fields evaluated. Accelerated atrazine dissipation occurred in soil from all fields of this study, with half-lives ranging from 1.8 to 3.2 d in the laboratory. The rapid atrazine dissipation rates were likely attributed to the history of atrazine use on all fields investigated in this study. Metolachlor dissipation was not considered accelerated and exhibited half-lives ranging from 9.0 to 10.7 d in the laboratory.