Impact of glyphosate-tolerant soybean and glufosinate-tolerant corn production on herbicide losses in surface runoff

Residual herbicides used in the production of soybean [Glycine max (L.) Merr] and corn (Zea mays L.) are often detected in surface runoff at concentrations exceeding their maximum contaminant levels (MCL) or health advisory levels (HAL). With the advent of transgenic, glyphosate-tolerant soybean and glufosinate-tolerant corn this concern might be reduced by replacing some of the residual herbicides with short half-life, strongly sorbed, contact herbicides. We applied both herbicide types to two chiseled and two no-till watersheds in a 2-yr corn-soybean rotation and at half rates to three disked watersheds in a 3-yr corn/soybean/wheat (Triticum aestivum L.)-red clover (Trifolium pratense L.) rotation and monitored herbicide losses in runoff water for four crop years. In soybean years, average glyphosate loss (0.07%) was approximately 1/7 that of metribuzin (0.48%) and about one-half that of alachlor (0.12%), residual herbicides it can replace. Maximum, annual, flow-weighted concentration of glyphosate (9.2 microg L(-1)) was well below its 700 microg L(-1) MCL and metribuzin (9.5 microg L(-1)) was well below its 200 microg L(-1) HAL, whereas alachlor (44.5 microg L(-1)) was well above its 2 microg L(-1) MCL. In corn years, average glufosinate loss (0.10%) was similar to losses of alachlor (0.07%) and linuron (0.15%), but about one-fourth that of atrazine (0.37%). Maximum, annual, flow-weighted concentration of glufosinate (no MCL) was 3.5 microg L(-1), whereas atrazine (31.5 microg L(-1)) and alachlor (9.8 microg L(-1)) substantially exceeded their MCLs of 3 and 2 microg L(-1), respectively. Regardless of tillage system, flow-weighted atrazine and alachlor concentrations exceeded their MCLs in at least one crop year. Replacing these herbicides with glyphosate and glufosinate can reduce the occurrence of dissolved herbicide concentrations in runoff exceeding drinking water standards.     

Comparative losses of glyphosate and selected residual herbicides in surface runoff from conservation-tilled watersheds planted with corn or soybean

Residual herbicides regularly used in conjunction with conservation tillage to produce corn ( L.) and soybean [ (L.) Merr] are often detected in surface water at concentrations that exceed their U.S. maximum contaminant levels (MCL) and ecological standards. These risks might be reduced by planting glyphosate-tolerant varieties of these crops and totally or partially replacing the residual herbicides alachlor, atrazine, linuron, and metribuzin with glyphosate, a contact herbicide that has a short half-life and is strongly sorbed to soil. Therefore, we applied both herbicide types at typical rates and times to two chisel-plowed and two no-till watersheds in a 2-yr corn/soybean rotation and at half rates to three disked watersheds in a 3-yr corn/soybean/wheat-red clover ( L.- L.) rotation and monitored herbicide losses in surface runoff for three crop years. Average dissolved glyphosate loss for all tillage practices, as a percentage of the amount applied, was significantly less ( ≤ 0.05) than the losses of atrazine (21.4x), alachlor (3.5x), and linuron (8.7x) in corn-crop years. Annual, flow-weighted, concentration of atrazine was as high as 41.3 μg L, much greater than its 3 μg L MCL. Likewise, annual, flow-weighted alachlor concentration (MCL = 2 μg L) was as high as 11.2 and 4.9 μg L in corn- and soybean-crop years, respectively. In only one runoff event during the 18 watershed-years it was applied did glyphosate concentration exceed its 700 μg L MCL and the highest, annual, flow-weighted concentration was 3.9 μg L. Planting glyphosate-tolerant corn and soybean and using glyphosate in lieu of some residual herbicides should reduce the impact of the production of these crops on surface water quality.     

Residual and contact herbicide transport through field lysimeters via preferential flow

Usage of glyphosate [N-(phosphonomethyl)-glycine] and glufosinate [2-amino-4-(hydroxy-methylphosphinyl)butanoic acid] may reduce the environmental impact of agriculture because they are more strongly sorbed to soil and may be less toxic than many of the residual herbicides they replace. Preferential flow complicates the picture, because due to this process, even strongly sorbed chemicals can move quickly to ground water. Therefore, four monolith lysimeters (8.1 m(2) by 2.4 m deep) were used to investigate leaching of contact and residual herbicides under a worst-case scenario. Glufosinate, atrazine (6-chloro-N(2)-ethyl-N(4)-isopropyl-1,3,5-triazine-2,4-diamine), alachlor [2-chloro-N-(2,6-diethylphenyl)-N-(methoxymethyl) acetamide], and linuron (3-3,4-dichlorophenyl-1-methoxy-1-methylurea) were applied in 1999 before corn (Zea mays L.) planting and glyphosate, alachlor, and metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one] were applied in 2000 before soybean [Glycine max (L.) Merr.] planting. A high-intensity rainfall was applied shortly after herbicide application both years. Most alachlor, metribuzin, atrazine, and linuron losses occurred within 1.1 d of rainfall initiation and the peak concentration of the herbicides coincided (within 0.1 d of rainfall initiation in 2000). More of the applied metribuzin leached compared with alachlor during the first 1.1 d after rainfall initiation (2.2% vs. 0.035%, P < 0.05). In 1999, 10 of 24 discrete samples contained atrazine above the maximum contaminant level (atrazine maximum contaminant level [MCL] = 3 mug L(-1)) while only one discrete sample contained glufosinate (19 mug L(-1), estimated MCL = 150 mug L(-1)). The results indicate that because of preferential flow, the breakthrough time of herbicides was independent of their sorptive properties but the transport amount was dependent on the herbicide properties. Even with preferential flow, glyphosate and glufosinate were not transported to 2.4 m at concentrations approaching environmental concern.     

Reducing atrazine losses: water quality implications of alternative runoff control practices

Water quality is being affected by herbicides, some allegedly harmful to human health. Under scrutiny is atrazine (1-chloro-3-ethylamino-5-isopropylamino-2,4,6-triazine), a commonly used herbicide in corn (Zea mays L.) and sorghum [Sorghum bicolor (L.) Moench] production. Concentrations of soluble and adsorbed atrazine losses sometimes exceed the safe drinking water standard of 3 microg L(-1) established by the USEPA. This study assesses the protective implications of runoff control structures and alternative crop farming practices to minimize atrazine losses. Using a computerized simulation model, APEX, the following four practices were the most effective with respect to the average atrazine loss as a percent of the amount applied: (i) constructing sediment ponds, 0.09%; (ii) establishing grass filter strips, 0.14%; (iii) banding a 25% rate of atrazine, 0.40%; and (iv) constructing wetlands, 0.45%. Other atrazine runoff management options, including adoption of alternative tillage practices such as conservation and no-till as well as splitting applications between fall and spring, were marginally effective.     

Fertilizer, tillage, and dairy manure contributions to nitrate and herbicide leaching

Few studies have examined the water quality impact of manure use in no-tillage systems. A lysimeter study in continuous corn (Zea mays L.) was performed on Maury silt loam (fine, mixed, semiactive, mesic Typic Paleudalf) to evaluate the effect(s) of tillage (no-till [NT] and chisel-disk [CD]), nitrogen fertilizer rate (0 and 168 kg N ha(-1)), and dairy manure application timing (none, spring, fall, or fall plus spring) on NO3-N, atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine), and alachlor [2-chloro-2'-6'-diethyl-N-(methoxymethyl)acetanilide] concentrations in leachate collected at a 90-cm depth. Herbicides were highest immediately after application, declining to less than 4 mug L(-1) in about two months. Manure and manure timing by tillage interactions had little effect on leachate herbicides; rather, the data suggest that macropores rapidly transmitted atrazine and alachlor through the soil. Tillage usually did not significantly affect leachate NO3-N, but no-tillage tended to cause higher NO(3)-N. Manuring caused higher NO3-N concentrations; spring manuring had more impact than fall, but fall manure contained about 78% of the N found in spring manure. Nitrate under spring "only fertilizer" treatment exceeded 10 mg L(-1) 38% of the time, compared with 15% for spring only manure treatment. After three years, manured soil leachate NO3-N exceeded that for soil receiving only N fertilizer. Soil profile (90 cm) NO3-N after corn harvest exceeding 22 kg N ha(-1) was associated with winter leachate NO3-N greater than 10 mg N L(-1). Manure can be used effectively in conservation tillage systems on this and similar soils. Accounting for all N inputs, including previous manure applications, will be important.     

SUSCEPTIBILITY OF INDIANA WATERSHEDS TO HERBICIDE CONTAMINATION1

ABSTRACT: An index of watershed susceptibility to surface water contamination by herbicides could be used to improve source water assessments for public drinking water supplies, prioritize watershed restoration projects, and direct funding and educational efforts to areas where the greatest environmental benefit can be realized. The goal of this study is to use streamflow and herbicide concentration data to develop and evaluate a method for estimating comparative watershed susceptibility to herbicide loss. United States Geological Survey (USGS) concentration data for five relatively water soluble herbicides (alachlor, atrazine, cyanazine, metolachlor, and simazine) were analyzed for 16 Indiana watersheds. Correlation was assessed between observed herbicide losses and: (1) a herbicide runoff index using GIS‐based land use, soil type, SCS runoff curve number, tillage practice, herbicide use estimates, and combinations of these factors; and (2) predicted herbicide losses from a non‐point source pollution model (NAPRA‐Web, an Internet‐based interface for GLEAMS). The highest adjusted R²value was found between herbicide concentration and the runoff curve number alone, ranging from 0.25 to 0.56. Predictions from the simulation model showed a poorer correlation with observed herbicide loss. This indicates potential for using the runoff curve number as a simple herbicide contamination susceptibility index.     

Runoff losses of sediment and phosphorus from no-till and cultivated soils receiving dairy manure

Managing manure in no-till systems is a water quality concern because surface application of manure can enrich runoff with dissolved phosphorus (P), and incorporation by tillage increases particulate P loss. This study compared runoff from well-drained and somewhat poorly drained soils under corn (Zea mays, L.) production that had been in no-till for more than 10 yr. Dairy cattle (Bos taurus L.) manure was broadcast into a fall planted cover crop before no-till corn planting or incorporated by chisel/disk tillage in the absence of a cover crop. Rainfall simulations (60 mm h(-1)) were performed after planting, mid-season, and post-harvest in 2007 and 2008. In both years and on both soils, no-till yielded significantly less sediment than did chisel/disking. Relative effects of tillage on runoff and P loss differed with soil. On the well-drained soil, runoff depths from no-till were much lower than with chisel/disking, producing significantly lower total P loads (22-50% less). On the somewhat poorly drained soil, there was little to no reduction in runoff depth with no-till, and total P loads were significantly greater than with chisel/disking (40-47% greater). Particulate P losses outweighed dissolved P losses as the major concern on the well-drained soil, whereas dissolved P from surface applied manure was more important on the somewhat poorly drained soil. This study confirms the benefit of no-till to erosion and total P runoff control on well-drained soils but highlights trade-offs in no-till management on somewhat poorly drained soils where the absence of manure incorporation can exacerbate total P losses.     

Phosphorus runoff: effect of tillage and soil phosphorus levels

Continued inputs of fertilizer and manure in excess of crop requirements have led to a build-up of soil phosphorus (P) levels and increased P runoff from agricultural soils. The objectives of this study were to determine the effects of two tillage practices (no-till and chisel plow) and a range of soil P levels on the concentration and loads of dissolved reactive phosphorus (DRP), algal-available phosphorus (AAP), and total phosphorus (TP) losses in runoff, and to evaluate the P loss immediately following tillage in the fall, and after six months, in the spring. Rain simulations were conducted on a Typic Argiudoll under a corn (Zea mays L.)-soybean [Glycine max (L.) Merr.] rotation. Elapsed time after tillage (fall vs. spring) was not related to any form of P in runoff. No-till runoff averaged 0.40 mg L(-1) and 0.05 kg ha(-1) DRP and chisel-plow plots averaged 0.24 mg L(-1) and 0.02 kg ha(-1) DRP concentration and loads, respectively. The relationship between DRP and Bray P1 extraction values was approximated by a logistic function (S-shaped curve) for no-till plots and by a linear function for tilled plots. No significant differences were observed between tillage systems for TP and AAP in runoff. Bray P1 soil extraction values and sediment concentration in runoff were significantly related to the concentrations and amounts of AAP and TP in runoff. These results suggest that soil Bray P1 extraction values and runoff sediment concentration are two easily measured variables for adequate prediction of P runoff from agricultural fields.     

Stream transport of herbicides and metabolites in a tile-drained, agricultural watershed

The occurrence of metabolites of many commonly used herbicides in streams has not been studied extensively in tile-drained watersheds. We collected water samples throughout the Upper Embarras River watershed [92% corn, Zea mays L., and soybean, Glycine max (L.) Merr.] in east-central Illinois from March 1999 through September 2000 to study the occurrence of atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine), metolachlor 12-chloro-N-(2-ethyl-6-methylphenyl)-N-(methoxy-1-methylethyl) acetamide], alachlor [2-chloro-N-(2,6-diethylphenyl)-N-(methoxymethyl) acetamide], acetochlor [2-chloro-N-(ethoxymethyl)-N-(2-ethyl-6-methylphenyl) acetamide], and their metabolites. River water samples were collected from three subwatersheds of varying tile density (2.8-5.3 km tile km(-2)) and from the outlet (United States Geological Survey [USGS] gage site). Near-record-low totals for stream flow occurred during the study, and nearly all flow was from tiles. Concentrations of atrazine at the USGS gage site peaked at 15 and 17 microg L(-1) in 1999 and 2000, respectively, and metolachlor at 2.7 and 3.2 microg L(-1); this was during the first significant flow event following herbicide applications. Metabolites of the chloroacetanilide herbicides were detected more often than the parent compounds (evaluated during May to July each year, when tiles were flowing), with metolachlor ethanesulfonic acid [2-[(2-ethyl-6-methylphenyl)(2-methoxy-1-methylethyl)amino]-2-oxoethanesulfonic acid] detected most often (> 90% from all sites), and metolachlor oxanilic acid [2-[(2-ethyl-6-methylphenyl)(2-methoxy-1-methylethyl)amino]-2-oxoacetic acid] second (40-100% of samples at the four sites). When summed, the median concentration of the three chloroacetanilide parent compounds (acetochlor, alachlor, and metolachlor) at the USGS gage site was 3.4 microg L(-1), whereas it was 4.3 microg L(-1) for the six metabolites. These data confirm the importance of studying chloroacetanilide metabolites, along with parent compounds, in tile-drained watersheds.     

Retention and runoff losses of atrazine and metribuzin in soil

Minimizing herbicide runoff and mobility in the soil and thus potential contamination of water resources is a national concern. Metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one] and atrazine [2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine] dynamics in surface soils and in runoff waters were studied on six 0.2-ha sugarcane (Saccharum spp.) plots of a Commerce silt loam (fine-silty, mixed, superactive, nonacid, thermic Fluvaquentic Endoaquept) during three growing seasons under different best management practices. Metribuzin was applied in the spring as a postemergence herbicide and atrazine was applied following winter harvest. Both herbicides were applied on top of the sugarcane rows as 0.6- or 0.9-m band width application, or broadcast application, where the entire area was treated. Maximum effluent concentrations were measured from the broadcast treatment and ranged from 600 to 1100 microg L(-1) for atrazine and 250 to 450 microg L(-1) for metribuzin. Atrazine runoff losses were highest for the broadcast treatment (2.8-11% of that applied) and lowest for the 0.6-m band treatment (1.9-7.6%), with a similar trend for metribuzin losses. Measured extractable herbicides from the surface soil exhibited a sharp decrease with time and were well described with a simple first-order decay model. For atrazine, estimates for the decay rate (lambda) were higher than for metribuzin. Results based on laboratory adsorption-desorption (kinetic-batch) measurements were consistent with field observations. The distribution coefficients (Kd) for atrazine exhibited stronger retention over time in comparison with metribuzin on the Commerce soil. Moreover, discrepancies between adsorption isotherm and desorption indicated slower release and that hysteresis was more pronounced for atrazine compared with metribuzin.     

Comparison of atrazine losses in three small headwater catchments

Understanding the processes causing herbicide transport to surface waters is crucial to determine mitigation options to reduce these losses. To this end, we investigated the atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-triazine) transport in three agricultural catchments (1.1-2.1 km2) in the watershed of Lake "Greifensee" (Switzerland). In 1999, atrazine application data were recorded for all three catchments. Time proportional samples were taken at a high temporal resolution at the catchment outlets. Extremely wet conditions caused large relative losses from the catchments, ranging between 0.6 and 3.5% of the amount applied. Most of the atrazine load was due to event-driven diffuse losses from the fields. Farmyard runoff contributed less but caused the highest concentrations (up to 31 microg L(-1)) in the brooks. The maximum concentrations due to diffuse losses varied between 1.2 and 8.2 microg L(-1) among the catchments. Despite different absolute concentration levels, the concentration time-series were very similar. It seems that the travel-times within the catchments were mainly controlled by the rainfall pattern with little influence of the catchment properties. These properties, however, caused the relative losses to vary by a factor of 6 between the catchments. This variability could be partly explained by differences in the connectivity of the fields to the brooks and by their hydrological soil properties. A comparison of the losses from the three catchments with those from the entire watershed of Lake Greifensee demonstrated that they were representative for the larger area. Hence, the study results provide a good data set to evaluate distributed models predicting herbicide losses.     

Alachlor and bentazone losses from subsurface drainage of two soils

Atrazine (6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4-diamine) is frequently detected at high concentrations in ground water. Bentazone [3-isopropyl-1H-2,1,3-benzothiadiazin-4(3H)-one 2,2-dioxide] plus alachlor (2-chloro-2',6'-diethyl-N-methoxymethylacetanilide) is a potential herbicide combination used as a substitute for atrazine. Thus, the objective of this study was to assess the environmental risk of this blend. Drainage water contamination by bentazone and alachlor was assessed in silty clay (Vertic Eutrochrept) and silt loam (Aquic Hapludalf) soils under the same management and climatic conditions. Drainage volumes and concentrations of alachlor and bentazone were monitored after application. Herbicides first arrived at the drains after less than 1 cm of net drainage. This is consistent with preferential flow and suggests that about 3% of the pore volume was active in rapid transport. During the monitoring periods, bentazone losses were higher (0.11-2.40% of the applied amount) than alachlor losses (0.00-0.28%) in the drains of the silty clay and silt loam. The rank order of herbicide mass losses corresponded with the rank order of herbicide adsorption coefficients. More herbicide residues were detected in drainage from the silty clay, probably due to preferential flow and more intensive drainage in this soil than the silt loam. Surprisingly, herbicide losses were higher in the drains of both soils in the drier of the two study years. This could be explained by the time intervals between the treatments and first drainage events, which were longer in the wetter year. Results suggest that the drainage phases occurred by preferential flow in the spring-summer period, with correspondingly fast leaching of herbicides, and by matrix flow during the fall-winter period, with slower herbicide migration.     

Herbicide transport to surface waters at field and watershed scales in a Mediterranean vineyard area

The contamination of soil and runoff water by two herbicides, diuron [N'-(3,4-dichlorphenyl)-N,N-dimethylurea] and simazine (6-chloro-N,N'-diethyl-1,3,5-triazine-2,4-diamine), were monitored on two fields, one no-till and one tilled. Experiments were carried out in a 91.4-ha watershed in southern France during the 1997 growing season in order to understand the patterns of pesticide transport from field to watershed. The persistence of the herbicides in soil was prolonged due to the climatic conditions. At the field scale, annual herbicide loads were due to overland flow and amounted to 65.6 and 6.3 g ha(-1) of diuron for the no-till and tilled field, respectively, and to 29.6 and 1.83 g ha(-1) of simazine. Maximum herbicide concentrations exceeded 580 microg L(-1) during the first storm event after application and decreased thereafter but remained for 8 mo above 0.1 microg L(-1). At the watershed outlet, estimated annual loads amounted to 4.12 g ha(-1) of diuron and 0.56 g ha(-1) of simazine. Among them, 96% of the losses in diuron and 83% of those in simazine were caused by the fast transmission through the network of ditches of the overland flow exiting the fields. For diuron, which was sprayed over most of the vineyards, its in-stream concentrations during storm flow were close to those at the outlet of the fields. The herbicide loads in baseflow were smaller than 0.2 g ha(-1). The patterns of the loads at the field and watershed scales suggested that a major part of the herbicides leaving the fields reinfiltrated to the ground water by seepage through the ditches, and was there degraded or adsorbed.     

Atrazine and alachlor transport in claypan soils as influenced by differential antecedent soil water content

Increased attention to ground water contamination has encouraged an interest in mechanisms of solute transport through soils. Few studies have investigated the effect of the initial soil water content on the transport and degradation of herbicides for claypan soils. We investigated the effect of claypan soils at initial field capacity vs. permanent wilting level on atrazine and alachlor transport. The soil studied was Mexico silt loam (fine, smectitic, mesic Aeric Vertic Epiaqualf) with a subsoil clay content, primarily montmorillonite, of >40%. Strontium bromide, atrazine, and alachlor were applied to plots; half were at field capacity (Wet treatment), and half were near the permanent wilting point (Dry treatment). Soil cores were removed at selected depths and times, and cores were analyzed for bromide and herbicide concentrations. Bromide, atrazine, and alachlor were detected at the 0.90-m depth in dry plots within 15 d after experiment initiation. Bromide was detected 0.15 m deeper (P < 0.05) in the Dry compared with the Wet treatment at 1, 7, and 60 d after application and >0.30 m deeper (P < 0.01) in the Dry treatment at 15 and 30 d after application; similar treatment results were found for atrazine and alachlor, although on fewer dates with significant differences. The mobility order of the applied chemicals was bromide > atrazine > alachlor. The atrazine apparent half-life was significantly longer in the Dry plots compared with the Wet plots. The retardation factor determined from the relative velocity of each herbicide to that of bromide was higher for alachlor than for atrazine. This study identifies the impact that shrinkage cracks have for different moisture conditions on preferential transport of herbicides in claypan soils.     

Major herbicides in ground water: results from the National Water-Quality Assessment

To improve understanding of the factors affecting pesticide occurrence in ground water, patterns of detection were examined for selected herbicides, based primarily on results from the National Water-Quality Assessment (NAWQA) program. The NAWQA data were derived from 2,227 sites (wells and springs) sampled in 20 major hydrologic basins across the USA from 1993 to 1995. Results are presented for six high-use herbicides--atrazine (2-chloro-4-ethylamino-6-isopropylamino-s-triazine), cyanazine (2-[4-chloro-6-ethylamino-1,3,5triazin-2-yl]amino]-2-methylpropionitrile), simazine (2-chloro-4,6-bis-[ethylamino]-s-triazine), alachlor (2-chloro-N-[2,6-diethylphenyl]-N-[methoxymethyl]acetamide), acetochlor (2-chloro-N-[ethoxymethyl]-N-[2-ethyl-6-methylphenyl]acetamide), and metolachlor (2-chloro-N-[2-ethyl-6-methylphenyl]-N-[2-methoxylethyl]acetamide)--as well as for prometon (2,4-bis[isopropylamino]-6-methoxy-s-triazine), a nonagricultural herbicide detected frequently during the study. Concentrations were <1 microg L(-1) at 98% of the sites with detections, but exceeded drinking-water criteria (for atrazine) at two sites. In urban areas, frequencies of detection (at or above 0.01 microg L(-1)) of atrazine, cyanazine, simazine, alachlor, and metolachlor in shallow ground water were positively correlated with their nonagricultural use nationwide (P < 0.05). Among different agricultural areas, frequencies of detection were positively correlated with nearby agricultural use for atrazine, cyanazine, alachlor, and metolachlor, but not simazine. Multivariate analysis demonstrated that for these five herbicides, frequencies of detection beneath agricultural areas were positively correlated with their agricultural use and persistence in aerobic soil. Acetochlor, an agricultural herbicide first registered in 1994 for use in the USA, was detected in shallow ground water by 1995, consistent with previous field-scale studies indicating that some pesticides may be detected in ground water within 1 yr following application. The NAWQA results agreed closely with those from other multistate studies with similar designs.     

Runoff and drainage losses of atrazine, metribuzin, and metolachlor in three water management systems

Rainfall can transport herbicides from agricultural land to surface waters, where they become an environmental concern. Tile drainage can benefit crop production by removing excess soil water but tile drainage may also aggravate herbicide and nutrient movement into surface waters. Water management of tile drains after planting may reduce tile drainage and thereby reduce herbicide losses to surface water. To test this hypothesis we calculated the loss of three herbicides from a field with three water management systems: free drainage (D), controlled drainage (CD), and controlled drainage with subsurface irrigation (CDS). The effect of water management systems on the dissipation of atrazine (6-chloro-N2-ethyl-N4-isopropyl-1,3,5-triazine-2,4-diamine), metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazine-5(4H)-one), and metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-methoxy-1-methylethyl)acetamide] in soil was also monitored. Less herbicide was lost by surface runoff from the D and CD treatments than from CDS. The CDS treatment increased surface runoff, which transported more herbicide than that from D or CD treatments. In one year, the time for metribuzin residue to dissipate to half its initial value was shorter for CDS (33 d) than for D (43 d) and CD (46 d). The half-life of atrazine and metolachlor were not affected by water management. Controlled drainage with subsurface irrigation may increase herbicide loss through increased surface runoff when excessive rain is received soon after herbicide application. However, increasing soil water content in CDS may decrease herbicide persistence, resulting in less residual herbicide available for aqueous transport.     

Herbicide retention in soil as affected by sugarcane mulch residue

Reducing surface and subsurface losses of herbicides in the soil and thus their potential contamination of water resources is a national concern. This study evaluated the effectiveness of sugarcane (Saccharum spp.) residue (mulch cover) in reducing nonpoint-source contamination of applied herbicides from sugarcane fields. Specifically, the effect of mulch residue on herbicide retention was quantified. Two main treatments were investigated: a no-till treatment and a no-mulch treatment. The amounts of extractable atrazine [2-chloro-4-(isopropylamino)-6-ethylamino-s-triazine], metribuzin [4-amino-6-(1,1-dimethylethyl)-3-(methylthio)-1,2,4-triazin-5(4H)-one], and pendimethalin [N-(ethylpropyl)-3,4-dimethyl-2,6-dinitroaniline] from the mulch residue and the surface soil layer were quantified during the 1999 and 2000 growing seasons. Significant amounts of applied herbicides were intercepted by the mulch residue. Extractable concentrations were at least one order of magnitude higher for the mulch residue compared with that retained by the soil. Moreover, the presence of mulch residue on the sugarcane rows was highly beneficial in minimizing runoff losses of the herbicides applied. When the residue was not removed, a reduction in runoff-effluent concentrations, as much as 50%, for atrazine and pendimethalin was realized. Moreover, the presence of mulch residue resulted in consistently lower estimates for rates of decay or disappearance of atrazine and pendimethalin in the surface soil.     

The acetochlor registration partnership surface water monitoring program for four corn herbicides

A surface drinking water monitoring program for four corn (Zea mays L.) herbicides was conducted during 1995-2001. Stratified random sampling was used to select 175 community water systems (CWSs) within a 12-state area, with an emphasis on the most vulnerable sites, based on corn intensity and watershed size. Finished drinking water was monitored at all sites, and raw water was monitored at many sites using activated carbon, which was shown capable of removing herbicides and their degradates from drinking water. Samples were collected biweekly from mid-March through the end of August, and twice during the off-season. The analytical method had a detection limit of 0.05 microg L(-1) for alachlor [2-chloro-N-(2,6-diethylphenyl)-N-(methoxymethyl)-acetamide] and 0.03 microg L(-1) for acetochlor [2-chloro-N-(ethoxymethyl)-N-(2-ethyl-6-methylphenyl)-acetamide], atrazine [6-chloro-N-ethyl-N'-(1-methylethyl)-1,3,5-triazine-2,4-diamine], and metolachlor [2-chloro-N-(2-ethyl-6-methylphenyl)-N-(2-methoxy-1-methylethyl)-acetamide]. Of the 16528 drinking water samples analyzed, acetochlor, alachlor, atrazine, and metolachlor were detected in 19, 7, 87, and 53% of the samples, respectively. During 1999-2001, samples were also analyzed for the presence of six major degradates of the chloroacetanilide herbicides, which were detected more frequently than their parent compounds, despite having higher detection limits of 0.1 to 0.2 microg L(-1). Overall detection frequencies were correlated with product use and environmental fate characteristics. Reservoirs were particularly vulnerable to atrazine, which exceeded its 3 microg L(-1) maximum contaminant level at 25 such sites during 1995-1999. Acetochlor annualized mean concentrations (AMCs) did not exceed its mitigation trigger (2 microg L(-1)) at any site, and comparisons of observed levels with standard measures of human and ecological hazards indicate that it poses no significant risk to human health or the environment.     

Herbicides and herbicide degradation products in Upper Midwest agricultural streams during August base-flow conditions

Herbicide concentrations in streams of the U.S. Midwest have been shown to decrease through the growing season due to a variety of chemical and physical factors. The occurrence of herbicide degradation products at the end of the growing season is not well known. This study was conducted to document the occurrence of commonly used herbicides and their degradation products in Illinois, Iowa, and Minnesota streams during base-flow conditions in August 1997. Atrazine, the most frequently detected herbicide (94%), was present at relatively low concentrations (median 0.17 microg L(-1)). Metolachlor was detected in 59% and cyanazine in 37% of the samples. Seven of nine compounds detected in more than 50% of the samples were degradation products. The total concentration of the degradation products (median of 4.4 microg L(-1)) was significantly greater than the total concentration of parent compounds (median of 0.26 microg L(-1)). Atrazine compounds were present less frequently and in significantly smaller concentrations in streams draining watersheds with soils developed on less permeable tills than in watersheds with soils developed on more permeable loess. The detection and concentration of triazine compounds was negatively correlated with antecedent rainfall (April-July). In contrast, acetanalide compounds were positively correlated with antecedant rainfall in late spring and early summer that may transport the acetanalide degradates into ground water and subsequently into nearby streams. The distribution of atrazine degradation products suggests regional differences in atrazine degradation processes.     

Phosphorus transport through subsurface drainage and surface runoff from a flat watershed in east central Illinois, USA

A long-term water quality monitoring program was established to evaluate the effects of agricultural management practices on water quality in the Little Vermilion River (LVR) watershed, IL. This watershed has intensive random and irregular subsurface drainage systems. The objective of this study was to assess the fate and transport of soluble phosphorus (soluble P) through subsurface drainage and surface runoff. Four sites (sites A, B, C, and E) that had subsurface and surface monitoring programs were selected for this study. Three of the four study sites had corn (Zea mays L.) and soybeans (Glycine max L.) planted in rotations and the other site had seed corn and soybeans. Subsurface drainage and surface runoff across all sites removed an average of 16.1 and 2.6% of rainfall, respectively. Annual flow-weighted soluble P concentrations fluctuated with the precipitation, while concentrations tended to increase with high precipitation coupled with high application rates. The long-term average flow-weighted soluble P concentrations in subsurface flow were 102, 99, 194, and 86 microg L(-1) for sites A, B, C, and E, respectively. In contrast, the long-term average flow-weighted soluble P concentrations in surface runoff were 270, 253, 534, and 572 microg L(-1) for sites As, Bs, Cs, and Es, respectively. These values were substantially greater than the critical values that promote eutrophication. Statistical analysis indicated that the effects of crop, discharge, and the interactions between site and discharge and crop and discharge on soluble P concentrations in subsurface flow were significant (alpha = 0.05). Soluble P mass loads in surface runoff responded to discharge more consistently than in the subsurface flow. Subsurface flow had substantially greater annual average soluble P mass loads than surface runoff due to greater flow volume.