Global solar radiation and energy yield estimation from photovoltaic power plants for small loads

Daily global solar radiation on a horizontal surface and duration of sunshine hours have been determined experimentally for five meteorological stations in Saudi Arabia, namely, Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser sites. Five-years of data covering 1998–2002 period have been used. Suitable Angstrom models have been developed for the global solar radiation estimation as a function of the sunshine duration for each respective sites. Daily averages of monthly solar PV power outputs have been determined using the Angstrom models developed. The effect of the PV cell temperature on the PV efficiency has been considered in calculating the PV power output. The annual average PV output energy has been discussed in all five sites for small loads. The minimum and maximum monthly average values of the daily global solar radiation are found to be 12.09 MJ/m²/d and 30.42 MJ/m²/d for Al-Qaisumah and Al-Jouf in the months of December June, respectively. Minimum monthly average sunshine hours of 5.89 hr were observed in Al-Qaisumah in December while a maximum of 12.92 hr in Al-Jouf in the month of June. Shortest range of sunshine hours of 7.33–10.12 hr was recorded at Abha station. Minimum monthly average Solar PV power of 1.59 MJ/m²/day was obtained at Al-Qaisumah in the month of December and a maximum of 3.39 MJ/m²/day at Al-Jouf in June. The annual PV energy output was found to be 276.04 kWh/m², 257.36 kWh/m², 256.75 kWh/m², 245.44 kWh/m², and 270.95 kWh/m² at Abha, Al-Ahsa, Al-Jouf, Al-Qaisumah, and Wadi Al-Dawaser stations, respectively. It is found that the Abha site yields the highest solar PV energy among the five sites considered.     

Comparative study on performances of a heat-pipe PV/T system and a heat-pipe solar water heating system

The heat-pipe solar water heating (HP-SWH) system and the heat-pipe photovoltaic/thermal (HP-PV/T) system are two practical solar systems, both of which use heat pipes to transfer heat. By selecting appropriate working fluid of the heat-pipes, these systems can be used in the cold region without being frozen. However, performances of these two solar systems are different because the HP-PV/T system can simultaneously provide electricity and heat, whereas the HP-SWH system provides heat only. In order to understand these two systems, this work presents a mathematical model for each system to study their one-day and annual performances. One-day simulation results showed that the HP-SWH system obtained more thermal energy and total energy than the HP-PV/T system while the HP-PV/T system achieved higher exergy efficiency than the HP-SWH system. Annual simulation results indicated that the HP-SWH system can heat the water to the available temperature (45°C) solely by solar energy for more than 121 days per year in typical climate regions of China, Hong Kong, Lhasa, and Beijing, while the HP-PV/T system can only work for not more than 102 days. The HP-PV/T system, however, can provide an additional electricity output of 73.019 kWh/m², 129.472 kWh/m², and 90.309 kWh/m² per unit collector area in the three regions, respectively.     

Automated energy management in distributed electricity systems: An EEPOS approach

The increasing capacity of distributed electricity generation brings new challenges in maintaining a high security and quality of electricity supply. New techniques are required for grid support and power balance. The highest potential for these techniques is to be found on the part of the electricity distribution grid.

This article addresses this potential and presents the EEPOS project’s approach to the automated management of flexible electrical loads in neighborhoods. The management goals are (i) maximum utilization of distributed generation in the local grid, (ii) peak load shaving/congestion management, and (iii) reduction of electricity distribution losses. Contribution to the power balance is considered by applying two-tariff pricing for electricity.

The presented approach to energy management is tested in a hypothetical sensitivity analysis of a distribution feeder with 10 households and 10 photovoltaic (PV) plants with an average daily consumption of electricity of 4.54 kWh per household and a peak PV panel output of 0.38 kW per plant. Energy management shows efficient performance at relatively low capacities of flexible load. At a flexible load capacity of 2.5% (of the average daily electricity consumption), PV generation surplus is compensated by 34–100% depending on solar irradiance. Peak load is reduced by 30% on average. The article also presents the load shifting effect on electricity distribution losses and electricity costs for the grid user.     

The global solar radiation estimation and analysis of solar energy: Case study for Osmaniye,Turkey

This paper investigates the prediction of solar radiation model and actual solar energy in Osmaniye, Turkey. Four models were used to estimate using the parameters of sunshine duration and average temperature. In order to obtain the statistical performance analysis of models, the coefficient of determination (R²), mean absolute percentage error (MAPE), mean absolute bias error (MABE), and root mean square error (RMSE) were used. Results obtained from the linear regression using the parameters of sunshine duration and average temperature showed a good prediction of the monthly average daily global solar radiation on a horizontal surface. In order to obtain solar energy, daily and monthly average solar radiation values were calculated from the five minute average recorded values by using meteorological measuring device. As a result of this measurement, the highest monthly and yearly mean solar radiation values were 698 (April in 2013) and 549 (2014 year) W/m² respectively. On an annual scale the maximum global solar radiation changes from 26.38 MJ/m²/day by June to 19.19 MJ/m²/day by September in 2013. Minimum global solar radiation changes from 14.05 MJ/m²/day by October to 7.20 MJ/m²/day by January in 2013. Yearly average energy potential during the measurement period was 16.53 MJ/m²/day (in 2013). The results show that Osmaniye has a considerable solar energy potential to produce electricity.     

Energy recovery from municipal solid waste in Nigeria and its economic and environmental implications

An assessment of potential biomass resources in Nigeria for the production of methane and power generation is presented in this paper. Nigeria, as an underdeveloped and populous country, needs an uninterrupted source of energy. The country's energy problems have crippled large sectors of the economy. The percentage of people connected to the national grid is 40%. These 40% experience electricity supply failure on average 10–12 hours daily. Energy generation from municipal solid waste (MSW) is an effective MSW management strategy. Yearly waste generation has increased from 6,471 gigagrams (Gg) in 1959 to 26,600 Gg in 2015. This amount is projected to reach 36,250 Gg per year by 2030. Methane emission for 2015 was 491 Gg, and it is projected to reach 669 Gg in 2030. These values translate to 3.48 × 10⁹ kilowatt hours (kWh) of electricity for 2015, with a projected 4.74 × 10⁹ kWh by 2030. The revenue to be derived from the electricity that is generated could have been US$365.04 × 10⁶ for 2015, and it is estimated that it will reach US$473.82 × 10⁶ by 2030. It was found that methane emissions from MSW increased with time, and capturing this gas for energy production will lead to a sustainable waste management.     

Drying of salted silver jewfish in a hybrid solar drying system and under open sun: Modeling and performance analyses

This study investigated the thin-layer drying kinetics of salted silver jewfish in a hybrid solar drying system and under open sun. Ten drying models were compared with experimental data of salted silver jewfish drying. A new model was introduced, which is an offset linear logarithmic (offset modified Page model). The fit quality of the models was evaluated using the coefficient of determination (R²), root mean square error (RMSE), and sum of squared absolute error (SSAE). The result showed that Midilli et al. model and new model were comparable with two or three-term exponential drying models. This study also analyzed energy and exergy during solar drying of salted silver jewfish. Energy analysis throughout the solar drying process was estimated on the basis of the first law of thermodynamics, whereas exergy analysis during solar drying was determined on the basis of the second law of thermodynamics. At an average solar radiation of 540 W/m² and a mass flow rate of 0.0778 kg/sec, the collector efficiency and drying system efficiency were about 41% and 23%, respectively. Specific energy consumption was 2.92 kWh/kg. Moreover, the exergy efficiency during solar drying process ranged from 17% to 44%, with an average value of 31%. The values of improvement potential varied between 106 and 436 W, with an average of 236 W.     

Environmental Impact and Sustainable Development: An Analysis in the Context of Standards ISO 9001, ISO 14001, and OHSAS 18001

In this study, we seek to verify the contributions made by three international standards to efforts by eight companies to reduce their environmental impacts and move toward sustainable development. The standards considered in this article are the International Organization for Standardization's (ISO) 9001 (quality), ISO 14001 (environmental management systems), and the Occupational Health and Safety Assessment Series (OHSAS) 18001. The eight companies analyzed for this study are located in the state of Rio Grande do Sul in Brazil. As part of this work, the authors generated a proposed sustainable positioning matrix and placed each company within one of four quadrants—economic approach, environmental approach, social approach, and sustainability approach—derived from the context of the Triple Bottom Line (Elkington, 2004 ).     

Comparative performance assessment of mono crystalline,multi crystalline,and amorphous silicon grid-connected photovoltaic systems under actual climatic conditions of Agadir,Morocco

This paper analyses actual performance of three grid-connected photovoltaic systems based on different silicon technologies, installed at the faculty of sciences of Agadir. The outdoor facilities consist of 2.04 kW_p of mono crystalline (m-Si), 1.86 kW_p of amorphous (μcSi/a-Si:H), and 2.04 kW_p of multi crystalline (mc-Si) silicon PV systems. Datasets were collected during one entire year under real measured irradiation and ambient temperature conditions. The performance of these roof mounted PV systems was conducted on daily and monthly bases. Parameters like annual specific yield, system efficiency, and performance ratio were evaluated and found to be 1827 kWh/kW_p.year, 20.9% and 80.2% for amorphous, 1863 kWh/kW_p.year, 21.3% and 80.7%, for mono crystalline and 1895 kWh/kW_p.year, 21.7% and 82.2% for multi crystalline.     

Dams in the Amazon: Belo Monte and Brazil’s Hydroelectric Development of the Xingu River Basin

Hydroelectric dams represent major investments and major sources of environmental and social impacts. Powerful forces surround the decision-making process on public investments in the various options for the generation and conservation of electricity. Brazil’s proposed Belo Monte Dam (formerly Kararaô) and its upstream counterpart, the Altamira Dam (better known by its former name of Babaquara) are at the center of controversies on the decision-making process for major infrastructure projects in Amazonia. The Belo Monte Dam by itself would have a small reservoir area (440 km²) and large installed capacity (11, 181.3 MW), but the Altamira/Babaquara Dam that would regulate the flow of the Xingu River (thereby increasing power generation at Belo Monte) would flood a vast area (6140 km²). The great impact of dams provides a powerful reason for Brazil to reassess its current policies that allocate large amounts of energy in the country’s national grid to subsidized aluminum smelting for export. The case of Belo Monte and the five additional dams planned upstream (including the Altamira/Babaquara Dam) indicate the need for Brazil to reform its environmental assessment and licensing system to include the impacts of multiple interdependent projects.     

Observed Changes in Climate and Streamflow in the Upper Rio Grande Basin

Observed streamflow and climate data are used to test the hypothesis that climate change is already affecting Rio Grande streamflow volume derived from snowmelt runoff in ways consistent with model‐based projections of 21st‐Century streamflow. Annual and monthly changes in streamflow volume and surface climate variables on the Upper Rio Grande, near its headwaters in southern Colorado, are assessed for water years 1958–2015. Results indicate winter and spring season temperatures in the basin have increased significantly, April 1 snow water equivalent (SWE) has decreased by approximately 25%, and streamflow has declined slightly in the April–July snowmelt runoff season. Small increases in precipitation have reduced the impact of declining snowpack on trends in streamflow. Changes in the snowpack–runoff relationship are noticeable in hydrographs of mean monthly streamflow, but are most apparent in the changing ratios of precipitation (rain + snow, and SWE) to streamflow and in the declining fraction of runoff attributable to snowpack or winter precipitation. The observed changes provide observational confirmation for model projections of decreasing runoff attributable to snowpack, and demonstrate the decreasing utility of snowpack for predicting subsequent streamflow on a seasonal basis in the Upper Rio Grande Basin.     

GENERATION OF SYNTHETIC AND MISSING CLIMATIC DATA FOR PUERTO RICO1

ABSTRACT: Climatic data such as temperature, solar radiation, relative humidity, and wind speed have been widely used to estimate evapotranspiration. Moat of the solar radiation data and portions of the relative humidity data are either not available or missing from the records in Puerto Rico. Depending upon the availability and data characteristics of records, three methods (including a regression technique, an averaging of historical data, and a regional average) were used to generate missing data, and a time series analysis was used to synthesize a series of climatic data. The limitations and applicability of each method are discussed. The results showed that the time series analysis method can be successfully used to synthesize a series of monthly solar radiations for several stations. The regression technique and the regional average can be successfully applied to generate missing monthly solar radiation data. The regression technique and the averaging of historical data have been satisfactorily used to interpolate missing monthly relative humidity. The explained variance (R²) varied from 0.68 to 0.88, which are both significant at the 0.05 level of significance.     

Comparison of the Performance of Statistical Models in Forecasting Monthly Total Dissolved Solids in the Rio Grande1

Abudu, S., J.P. King, Z. Sheng, 2011. Comparison of the Performance of Statistical Models in Forecasting Monthly Total Dissolved Solids in the Rio Grande. Journal of the American Water Resources Association (JAWRA) 48(1): 10‐23. DOI: 10.1111/j.1752‐1688.2011.00587.x Abstract: This paper presents the application of autoregressive integrated moving average (ARIMA), transfer function‐noise (TFN), and artificial neural networks (ANNs) modeling approaches in forecasting monthly total dissolved solids (TDS) of water in the Rio Grande at El Paso, Texas. Predictability analysis was performed between the precipitation, temperature, streamflow rates at the site, releases from upstream reservoirs, and monthly TDS using cross‐correlation statistical tests. The chi‐square test results indicated that the average monthly temperature and precipitation did not show significant predictability on monthly TDS series. The performances of one‐ to three‐month‐ahead model forecasts for the testing period of 1984‐1994 showed that the TFN model that incorporated the streamflow rates at the site and Caballo Reservoir release improved monthly TDS forecasts slightly better than the ARIMA models. Except for one‐month‐ahead forecasts, the ANN models using the streamflow rates at the site as inputs resulted in no significant improvements over the TFN models at two‐month‐ahead and three‐month‐ahead forecasts. For three‐month‐ahead forecasts, the simple ARIMA showed similar performance compared to all other models. The results of this study suggested that simple deseasonalized ARIMA models could be used in one‐ to three‐month‐ahead TDS forecasting at the study site with a simple, explicit model structure and similar model performance as the TFN and ANN models for better water management in the Basin.     

Processing of Straw/Corn Stover: Comparison of Life Cycle Emissions

The LCA emissions from four renewable energy routes that convert straw/corn stover into usable energy are examined. The conversion options studied are ethanol by fermentation, syndiesel by oxygen gasification followed by Fischer Tropsch synthesis, and electricity by either direct combustion or biomass integrated gasification and combined cycle (BIGCC). The greenhouse gas (GHG) emissions of these four options are evaluated, drawing on a range of studies, and compared to the conventional technology they would replace in a western North American setting. The net avoided GHG emissions for the four energy conversion processes calculated relative to a “business as usual” case are 830 g CO₂e/kWh for direct combustion, 839 g CO₂e/kWh for BIGCC, 2,060 g CO₂e/L for ethanol production, and 2,440 g CO₂e/L for FT synthesis of syndiesel. The largest impact on avoided emissions arises from substitution of biomass for fossil fuel. Relative to this, the impact of emissions from processing of fossil fuel, e.g., refining of oil to produce gasoline or diesel, and processing of biomass to produce electricity or transportation fuels, is minor.     

Deployment of parabolic trough concentrated solar power plants in North Africa – a case study for Libya

The study addresses the potential of using concentrated solar power plants (CSPs) as a sustainable alternative of clean energy generation in the Mediterranean region and, in particular, in its North Africa shore. This location presents attractive conditions for the installation of CSPs, in particular high solar irradiation, good manpower concentration, and proximity and availability of water resources for condenser cooling. Energetic, exergetic, and economic analyses were conducted taking into consideration a particular type of CSPs - the parabolic trough concentrated solar power plant, which incorporates the most proven technology and it is already used in Southern Europe (Spain). In addition, the study considered the impact of project financing and incentives on the cost of energy. The combination of higher values for performance and potentially lower levelized cost of electricity (LCE) for the North Africa Mediterranean Rim than the South of Spain region can yield a very favorable return for the invested capital. Tripoli compared to Almeria presented superior performance and potentially lower LCE values ($0.18/kWh versus $0.22/kWh). This is significant, even when it is taken into consideration the fact that the plant in Tripoli, despite a relatively modest capacity factor of 34%, has a large gross power output of 173,886 MWhe. In addition, the implementation at the Tripoli location of a plant similar to the Anadsol plant has a slight advantage (2–3%) in terms of overall efficiency.     

Photovoltaic-thermal (PV/t) panel to minimize electrical and air conditioning energy consumption of a typical office in Beirut

A combined photovoltaic–thermal (PV/t) panel is proposed to produce simultaneously electricity and heat from one integrated unit. The unit utilizes effectively the solar energy through achieving higher PV electrical efficiency and using the thermal energy for heating applications. To predict the performance of the PV/t at a given environmental conditions, a transient mathematical model was developed. The model was integrated in a heating application for a typical office space in the city of Beirut to provide the office needs for electricity, heating during winter season, and dehumidification and evaporative cooling during the summer season. To minimize the yearly office energy (electrical and heat) needs, the PV/t panel cooling air flow rate and the dehumidification regeneration temperature were determined for opimal unit operation. Thermal energy savings of up to 85% in winter and 71% in summer were achived compared to conventional systems at a payback period of 8 years for the panels.     

Evaluation of Rio Grande Management Alternatives Using a Surface‐Water/Ground‐Water Model1

Abstract: Previous investigations observed significant seepage losses from the Rio Grande to the shallow aquifer between Socorro and San Antonio, New Mexico. High‐resolution telescopic modeling was used along a 10‐km reach of the Rio Grande and associated drains and canals to evaluate several management alternatives aimed at improving river conveyance efficiency. Observed data consisted of ground‐water and surface‐water elevations, seepage rates along the Rio Grande and associated canals and drains, and borehole geology. Model calibration was achieved by adjusting hydraulic conductivity and specific storage until the output matched observed data. Sensitivity analyses indicated that the system was responsive to changes in hydrogeologic properties, especially when such alterations increased vertical connectivity between layers. The calibrated model predicted that removal of the low flow conveyance channel, a major channel draining the valley, would not only decrease river seepage by 67%, but also decrease total flow through the reach by 75%. The decreased flow through the reach would result in increased water logging and an average increase in ground‐water elevations of 1.21 meter. Simulations of the system with reduced riparian evapotranspiration rates or a relocated river channel also predicted decreased river seepage, but to a much lesser degree.     

The Design of a New Energy-conservation Type Solar-powered Lighting System Using a High‐pressure Sodium Lamp

This study designs and applies a new energy-conservation type solar-powered lighting system using a high-pressure sodium lamp to areas not having any utility company's electricity. The proposed system uses a zero-voltage-switching (ZVS) DC/DC converter in the batteries’ charge circuit to reduce the switching loss for a higher charging efficiency. Said system also adopts the maximum power point tracking (MPPT) technique to maximize the solar panels’ photovoltaic conversion capability. When dark, the batteries in the proposed system will discharge, with a raised voltage, through a push-pull DC/DC converter; said voltage, as the input voltage of the series-parallel resonant inverter, will be regulated to dim the lamp. To enable the efficient usage of the batteries’ stored energy capacity, this control scheme of the proposed system may adjust the night-time discharge time lengths, according to season difference, and compute the usable capacity for the load, according to the batteries’ charged voltage, so as to select a suitable pre-scheduled light-dimming curve for the lamp to achieve energy conservation for the batteries and continuity in lighting when dark.     

Optimization of a Wind/PV Hybrid Power Generation System

This study investigates the wind and solar electricity generation availability at the Solar Energy Institute of Ege University, Izmir, Turkey. The main purpose of this study is to design an appropriate wind-PV hybrid system to cover the electricity consumption of the Institute. In order to do this, monthly average solar irradiation and wind speed data are used, which were measured, consisting of hourly records over an eight-year period from 1995–2002. Simple models were developed to determine wind, solar, and hybrid power resources per unit area. Correlations between the solar and wind power data were carried out on an hourly, daily, and monthly basis. It is shown that the hybrid system can be applied for the efficient and economic utilization of these resources.