Multiresidue determination of pesticides in tea by gas chromatography-tandem mass spectrometry

An efficient and reliable GC-MS/MS method for the multiresidue determination of pesticides in tea was developed by modifying the Japanese official multiresidue method. Sample preparation was carefully optimized for the efficient removal of coextracted matrix components. The optimal sample preparation procedure involved swelling of the sample in water; extraction with acetonitrile; removal of water by salting-out; and sequential cleanup by ODS, graphitized carbon black/primary secondary amine (GCB/PSA) and silica gel cartridges prior to GC-MS/MS analysis. The recoveries of 162 pesticides from fortified (at 0.01 mg kg^?1) green tea, oolong tea, black tea and matcha (powdered green tea) were mostly (95–98% of the tested pesticides) within the range of 70–120%, with relative standard deviations of <20%. Poor recovery of triazole pesticides was considered to be due to low recovery from the silica gel cartridges. The test solutions obtained by the modified method contained relatively small amounts of pigments, caffeine and other matrix components and were cleaner than those obtained by the original Japanese official multiresidue method. No interfering peaks were observed in the blank chromatograms, indicating the high selectivity of the modified method. The overall results suggest that the developed method is suitable for the quantitative analysis of GC-amenable pesticide residues in tea.     

Surrogate study for dioxins from municipal waste incinerator in startup condition: applicability as a dioxin control indicator and an organohalogen emission warning

Dioxins and their surrogates were continuously monitored during the startup of two municipal waste in cinerators (MWIs). The surrogates studied included low-volatility organohalogen compounds (LVOH) sampled by online systems, as well as chlorobenzenes (CBs) and chlorophenols (CPs). The changes in levels of LVOH, CBs, and CPs corresponded well with the trend of the toxicity equivalent quantity (TEQ). The correlation of LVOH with TEQ was fairly good, whereas that of CBs and CPs with TEQ was not consistent. The correlation of LVOH with TEQ involved a memory effect related to the delayed emission of less volatile compounds. The isomer analysis of the dioxins present under startup conditions showed evidence of the memory effect, i.e., highly chlorinated isomers were emitted slowly, whereas low-chlorinated isomers and LVOH decreased rapidly as the temperature rose. LVOH cannot act as a perfect dioxin surrogate, but it can give a versatile, quick, and comprehensive warning of the presence of organohalogen compounds because it is free from the memory effect and covers many kinds of organohalogen compounds, including dioxins.     

A modeling study of coarse particulate matter pollution in Beijing: regional source contributions and control implications for the 2008 Summer Olympics

In the last 10 yr, Beijing has made a great effort to improve its air quality. However, it is still suffering from regional coarse particulate matter (PM10) pollution that could be a challenge to the promise of clean air during the 2008 Olympics. To provide scientific guidance on regional air pollution control, the Mesoscale Modeling System Generation 5 (MM5) and the Models-3/Community Multiscale Air Quality Model (CMAQ) air quality modeling system was used to investigate the contributions of emission sources outside the Beijing area to pollution levels in Beijing. The contributions to the PM10 concentrations in Beijing were assessed for the following sources: power plants, industry, domestic sources, transportation, agriculture, and biomass open burning. In January, it is estimated that on average 22% of the PM10 concentrations can be attributed to outside sources, of which domestic and industrial sources contributed 37 and 31%, respectively. In August, as much as 40% of the PM10 concentrations came from regional sources, of which approximately 41% came from industry and 31% from power plants. However, the synchronous analysis of the hourly concentrations, regional contributions, and wind vectors indicates that in the heaviest pollution periods the local emission sources play a more important role. The implications are that long-term control strategies should be based on regional-scale collaborations, and that emission abatement of local sources may be more effective in lowering the PM10 concentration levels on the heavy pollution days. Better air quality can be attained during the Olympics by placing effective emission controls on the local sources in Beijing and by controlling emissions from industry and power plants in the surrounding regions.     

Integrated model of reaction rate equations and thermal energy balance in aerobic bioreactor for food waste decomposition

The integrated model is composed of two basic parts: one is a reaction rate model of biodegradation in combination with bioenergetics and the other is a thermal engineering model of energy flow and balance in the bioreactor. Integrating these models provides possibility to estimate microbial activity using time course of physicochemical parameters such as bed temperature, bed weight, and/or C0₂ concentration during decomposition.     

Development of new footwear sole surface pattern for prevention of slip-related falls

In this study, a new rubber surface pattern for a footwear sole was developed to prevent slip-related falls. This pattern shows a high static coefficient of friction (SCOF) and a high dynamic coefficient of friction (DCOF) when sliding against a liquid contaminated surface. A hybrid rubber block, in which a rubber block with a rough surface (Ra = 30.4 μm) was sandwiched between two rubber blocks with smooth surfaces (Ra = 0.98 μm), was prepared. The ratio of the rough surface area to the whole rubber block surface area r was 0%, 30%, 50%, 80%, and 100%. The coefficient of friction of the rubber blocks was measured when sliding against a stainless steel plate with Ra of 0.09 μm contaminated with a 90% aqueous solution of glycerol. While the SCOF increased with an increase of the rough surface area ratio r, the DCOF during steady-state sliding decreased with an increase of the rough surface area ratio r. The rough surface area ratio of 50% achieved a SCOF value around 0.5 or more and a DCOF value greater than 0.5. Furthermore, the difference in the value of the SCOF and DCOF was the smallest for the rubber block with r of 50%. The results indicated that the rubber block with r of 50% would be applicable to a footwear sole surface pattern to prevent slip and fall accidents on contaminated surfaces.     

Evaluation of non-methane hydrocarbon (NMHC) emissions based on an ambient air measurement in Tokyo area,Japan

Non-methane hydrocarbons (NMHCs) are known to have an important role on air quality due to their high reactivity. NMHC analysis has been performed on 148 ambient air samples collected at five different sites in the Kanto area (Tokyo metropolitan area and surrounding six prefectures) of Japan in summer and winter of 2008, and fifty NMHCs have been determined and quantified. A field measurement campaign has been conducted at one of the busiest intersections in Tokyo metropolitan area in winter of 2008. NMHC emissions are evaluated through comparison of distributions of individual NMHCs emitted from motor vehicles, which are estimated from the measurements, with those determined from the current emissions inventory. The comparison revealed that the measured distributions of acetylene, ethylene and toluene showed a good agreement with those estimated from the emissions inventory (the values estimated from the measurements are a factor of 1.5, 0.56 and 2.3 larger than the emissions inventory in median, respectively), however, propane and isobutane are found to be significantly underestimated in the emissions inventory (the measured values were a factor of 18 and 5.1 larger than the emissions inventory, respectively). The significant underestimate of propane can be explained by that the current emissions inventory does not consider emissions from liquefied propane gas (LPG) fueled vehicles. However, for isobutane, reasons for the underestimate are still unclear. Another field measurement has been conducted in summer of 2008, where the air samples have been collected at three different sites on the ground and by a helicopter as well. Remarkable high concentrations of 1-butene and cis- and trans-2-butenes have been sporadically observed in the samples collected at Urayasu in the coastal area of Tokyo bay. Calculated propylene equivalent (PE) concentrations of butenes revealed that those have a significantly important role in ozone formation when the air plume is affected by emissions from their emission sources. The PE concentrations of butenes varied from 0.1 to 39 ppbC, and accounted for 1.5–75% of total PE concentrations at Urayasu. Most of the continuous air quality monitoring stations does not record concentrations of individual hydrocarbons, therefore, the importance of reactive and low concentration hydrocarbon such as butenes might be overlooked in the current emissions inventory and/or air quality model. In this paper, the reliability of NMHC emissions is evaluated based on the field measurements. Their possible impacts on air quality in the Kanto area are discussed as well, based on the calculated propylene equivalent concentrations.     

The mild hydrothermal synthesis of hydrogrossular from coal ash

In this study, an attempt was made to synthesize hydrogrossular, a group of garnet minerals, under hydrothermal conditions at temperatures below 180°C, using coal ash, which is the solid waste from thermal power plants, as a starting material. A single phase corresponding to hydrogrossular was found at around 120°C, and the hydrogrossular coexisted with 11-Å tobermorite above 140°C. The hydrogrossular phase decreased with increasing reaction temperature, while that of 11-Å tobermorite increased concurrently. The physicochemical properties of the hydrogrossular obtained from the hydrothermal synthesis was characterized by X-ray diffraction thermogravimetry/differential thermal, analysis, scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray fluorescence spectroscopy. Received: September 4, 2000 / Accepted: March 7, 2001     

Evaluating households’ preferences regarding reducing power outages in rural areas: cases in the Ganges Floodplain in Bangladesh

This paper investigates household preferences regarding an improved supply of electricity in rural Bangladesh, where the expansion of stable electricity is an urgent policy issue. The paper examines household preferences regarding reductions in the frequency and duration of power outages. It also examines prior notification mechanisms that do not necessarily provide an increased supply of electricity but that allow households to prepare for potential power failures. A questionnaire survey designed as a choice experiment was applied to households to elicit preferences. The econometric analysis reveals that villagers prefer a reduction in both the frequency and duration of power outages and a 1-day prior notification of power outages. There are slight disparities in preferences according to the season and the timing of improvements (e.g., summer or winter and all day or peak hours). Thus, the present study may be beneficial for policymakers when considering the provision of electricity supply improvements in rural areas in exchange for slight increases in electricity tariffs.     

Modeling the current-voltage characteristics of thin-film silicon solar cells based on photo-induced electron transfer processes

Power conversion efficiency of p-i-n type microcrystalline silicon (c-Si:H) solar cells has been analyzed in terms of sequential processes of photo-induced electron transfer. The effect of the excitonic state on the charged carrier generation has been studied compared to a conventional scheme in which only charged carriers are taken into account for the operation of the solar cells. A numerical model has been developed to calculate current-voltage characteristics of solar cells on the basis of two types of charged carrier generation processes (exciton process and charged carrier process). The light trapping effect due to a textured back surface reflector (BSR) was embedded in the numerical model by using the effective medium theory in combination with the matrix method in the field of the electromagnetic theory of light. As an application of this modeling, it was found that the reported data of the power conversion efficiency were not explained by the conventional charged carrier process model and that the combined model of the charged carrier process with the exciton process well explains the performance of the p-i-n type c-Si:H solar cells. In this way, the typical power conversion efficiencies were estimated to be 10.5% for the device (i-layer thickness: 1.8 m) with the BSR (period: 600 nm; height: 250 nm) and 8.6% for the device with the flat reflector under the condition that the fractions of the exciton process and charged carrier process were 60% and 40%, respectively.