船舶排放及不确定性对中国空气质量的影响

船舶排放是我国沿海地区重要的人为排放源,但现有的船舶排放评估研究大多只关注区域尺度的影响分析,而且忽视了排放清单的不确定性,这在一定程度上削弱了评估结果的可靠性.为此,本文利用WRF-SMOKE-CAMQ空气质量模型,定量评估了船舶排放及其不确定性对我国七大沿海港口城市夏季空气质量的影响,结果表明：船舶排放对我国主要沿海港口城市的SO₂、NO_x和PM_2.5浓度贡献范围分别为16.5%~62.5%、21.9%~72.9%和5.9%~26.0%,尤其对宁波、青岛和深圳等港口城市空气质量的影响显著,主要是由于港口较高的船舶排放以及气象传输两方面原因造成的;如果考虑船舶排放清单的总量不确定性,船舶排放对沿海港口城市夏季SO₂、NO_x和PM_2.5的影响分别呈现1.0~3.1,2.1~5.5,0.3~0.9μg/m³的波动;考虑船舶排放清单的时空分配不确定性,船舶排放对沿海港口城市夏季SO₂、NO_x和PM_2.5的影响分别呈现1.9~15.7,5.1~29.3,0.6~2.5μg/m³的波动.可见,船舶排放清单的不确定性对沿海城市船舶排放贡献影响量化有明显的影响.所以在评估船舶排放对港口城市空气质量的影响时,要考虑船舶排放清单的不确定性,尤其是时空分配的不确定性.而合理的时空分配能够提高船舶排放清单的质量和对沿海空气质量模拟的准确性.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

石墨烯/聚苯胺修饰阴极对反硝化MFC性能影响

反硝化生物阴极微生物燃料电池（MFC）以电极为电子供体,在自养条件下完成硝酸盐去除过程.本研究以碳布（CC）为基底材料,分别制备获得还原氧化石墨烯修饰（rGO-CC）,聚苯胺修饰（PANI-CC）及二者复合修饰的CC电极（rGO/PANI-CC）,并考察其作为阴极材料对反硝化生物阴极MFC产电脱氮性能的影响.扫描电镜结果显示,rGO-CC和PANI-CC的碳纤维分别被片层状rGO和网状PANI覆盖,而rGO/PANI-CC表面呈现PANI在附着rGO的碳纤维上团聚的形貌,均增大了碳布的比表面积.循环伏安测试显示,rGO/PANI-CC具有最高的电化学活性.以rGO-CC,PANI-CC和rGO/PANI-CC为阴极构建MFC的产电能力分别提高了82%,24%和41%,其阴极对NO₃^--N的去除能力增强了23%,9%和13%.16S rDNA测序结果揭示修饰后电极表面微生物的多样性下降,Stappia和Pacacoccus属微生物的丰度增加.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

中国工业园区绿色发展政策对比分析及对策研究

为了提升我国工业园区绿色发展水平,对目前我国工业园区发展历程、现状特征进行了分析,对工业园区绿色发展政策进行了梳理和对比,并结合工业园区绿色发展中存在的问题提出了对策建议.研究表明:①我国工业园区经历了快速发展、调整发展和科学发展等阶段,在经济发展、资源与能源优化利用、污染减排等方面成效显著.②我国工业园区绿色发展的相关政策主要体现在国家生态工业示范园区创建、园区循环化改造、国家低碳工业园区试点、绿色园区建设和UNIDO绿色工业园区创建等工作中,这些政策在推动主体、实施路径、侧重方向上各不相同又各有特色,对推动工业园区节能减排绩效明显.③目前,我国工业园区绿色发展存在的问题主要表现在重视程度有待提升、风险防范意识有待加强、创新能力有待提高等方面.为此,提出了我国工业园区绿色发展对策建议:积极践行绿色发展理念,推进园区绿色化、生态化、低碳化建设,实现经济环境双赢;注意环境风险防控,确保环境安全;创新管理机制,强化监督管理.      

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

长三角背景点夏季大气PM2.5中水溶性无机离子污染特征及来源解析

为研究长三角背景点夏季PM_2.5污染特征,于2018年5月30日—8月15日在上海市崇明岛对PM_2.5样品进行昼夜采集,并对其中水溶性无机离子(Cl-、NO₃-、SO₄2-、Na+、NH₄+、K+、Mg2+、Ca2+)进行了分析.运用PSCF(潜在源贡献)方法判别污染物排放源区,并结合PCA(主成分分析)和PMF(正交矩阵因子)源解析探究PM_2.5来源.结果表明:①观测期间崇明岛ρ(PM_2.5)平均值为(33±21)μg/m3,低于GB 3095—2012《环境空气质量标准》一级标准限值(35 μg/m3),但在部分时段存在显著超标现象,ρ(PM_2.5)最高值在120 μg/m3以上.②水溶性无机离子质量浓度平均值为(14±9.3)μg/m3,占PM_2.5的42.4%,其中SNA(SO₄2-、NO₃-、NH₄+三者统称)为主要离子,占水溶性离子总质量浓度的85.7%.③n(NH₄+)/n(SO₄2-)(NH₄+与SO₄2-的摩尔浓度比)显示,清洁期〔ρ(PM_2.5) < 15 μg/m3〕呈贫铵状态,过渡期〔15≤ρ(PM_2.5)≤35 μg/m3〕和污染期〔ρ(PM_2.5)>35 μg/m3〕均呈富铵状态;过渡期SNA主要以NH₄HSO₄和NH₄NO₃形式存在,而污染期则主要以(NH₄)₂SO₄和NH₄NO₃形式存在.④通过对两次典型污染事件进行离子相关性分析和PSCF分析发现,E1污染事件(5月30日—6月8日)为局地生物质燃烧型污染事件,E2污染事件(7月23日—8月1日)为区域传输污染事件.源解析结果进一步表明,两次典型污染事件期间气态污染物的二次转化对PM_2.5的贡献最显著,贡献率分别为62.8%和59.8%;其次是生物质燃烧,其贡献率分别为32.5%和20.1%;E2污染事件期间海盐源对崇明岛PM_2.5贡献率较高(16.6%),远超过E1污染事件期间对PM_2.5的贡献率(2.7%).研究显示,区域输送对崇明岛PM_2.5有显著贡献,二次颗粒物累积是崇明岛PM_2.5超标的主要原因.      

福建省2005-2017年大气边界层SO2的时空变化特征

为研究近年来福建省SO₂污染的时空动态特征,利用臭氧观测仪（ozone monitoring instrument,OMI）卫星遥感反演的PBL（planetary boundary layer,大气边界层）SO₂柱含量数据,分析了2005-2017年福建省PBL SO₂柱含量的时空间分布特征.结果表明:①在长时间尺度上,PBL SO₂柱含量的变化趋势可分为2个时段,其中,2005-2011年PBL SO₂柱含量呈逐渐上升趋势,6 a增加了约0.027 DU,增长率约为6.12%;2011-2017年PBL SO₂柱含量呈下降趋势,7 a减少了约0.018 DU,下降率约为3.89%.②PBL SO₂柱含量呈明显的周期性变化特征,最小值和最大值分别出现在6月和12月,多年平均值分别约为0.383和0.555 DU.③PBL SO₂柱含量的3个高值区分别出现在沿海的福州市,厦门市、漳州市东部和泉州市西部,三明市和南平市部分地区,这3个高值区多年平均PBL SO₂柱含量分别约为0.505、0.495和0.485 DU.从城市尺度上来看,PBL SO₂柱含量最大值出现在厦门市,其多年平均值为（0.486±0.015）DU;其次为福州市,PBL SO₂柱含量多年平均值为（0.465±0.026）DU;最低值出现在漳州市,PBL SO₂柱含量多年平均值为（0.429±0.020）DU.④福建省PBL SO₂柱含量变化趋势在空间分布上存在明显的差异,不同时期、不同区域变化趋势不一致.2005-2011年PBL SO₂柱含量的变化范围为-0.13~0.18 DU,变化率范围为-25%~50%,PBL SO₂柱含量出现增长的区域主要是在高值区,如龙岩市西部、厦门市北部以及三明市东部等区域;2011-2017年PBL SO₂柱含量的变化范围为-0.13~0.15 DU,变化率范围为-29%~34%.2011-2017年福州市和厦门市PBL SO₂柱含量下降最为明显,减少了约0.10 DU,下降率约为25%.研究显示,卫星遥感估算的PBL SO₂柱含量具有一定的可靠性,可以用于区域SO₂污染的研究.